LG OLED65G6V Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

Please read this manual carefully before operating your set and retain
it for future reference.
www.lg.com
P/NO : MFL69365713 (1606-REV02)
Printed in Korea
*MFL69365713*
Safety and Reference
2
ENGLISH
Safety instructions
Please read these safety precautions carefully before
using the product.
WARNING
Do not place the TV and/or remote control in the following
environments:
•  A location exposed to direct sunlight
•  An area with high humidity such as a bathroom
•  Near any heat source such as stoves and other devices that
produce heat
•  Near kitchen counters or humidiers where they can easily be
exposed to steam or oil
•  An area exposed to rain or wind
•  Near containers of water such as vases
Otherwise, this may result in re, electric shock, malfunction or product
deformation.
Do not place the product where it might be exposed to dust. This may
cause a re hazard.
Mains Plug is the TV connecting/disconnecting device to AC mains
electric supply. This plug must remain readily attached and operable
when TV is in use.
Do not touch the power plug with wet hands. Additionally, if the cord
pin is wet or covered with dust, dry the power plug completely or wipe
dust o. You may be electrocuted due to excess moisture.
Make sure to connect Mains cable to compliant AC mains socket with
Grounded earth pin. (Except for devices which are not grounded on
earth.) Otherwise possibility you may be electrocuted or injured.
Insert power cable plug completely into wall socket otherwise if not
secured completely into socket, re ignition may break out.
Ensure the power cord does not come into contact with hot objects
such as a heater. This may cause a re or an electric shock hazard.
Do not place a heavy object, or the product itself, on power cables.
Otherwise, this may result in re or electric shock.
Bend antenna cable between inside and outside building to prevent
rain from owing in. This may cause water damaged inside the Product
and could give an electric shock.
When mounting TV onto wall make sure to neatly install and isolate
cabling from rear of TV as to not create possibility of electric shock /
re hazard.
ENGLISH
3
Do not plug too many electrical devices into a single multiple electrical
outlet. Otherwise, this may result in re due to over-heating.
Do not drop the product or let it fall over when connecting external
devices. Otherwise, this may result in injury or damage to the product.
Desiccant
Keep the anti-moisture packing material or vinyl packing out of the
reach of children. Anti-moisture material is harmful if swallowed. If
swallowed by mistake, force the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause suocation. Keep it out
of the reach of children.
Do not let your children climb or cling onto the TV.
Otherwise, the TV may fall over, which may cause serious injury.
Dispose of used batteries carefully to ensure that a small child does not
consume them. Please seek Doctor- Medical Attention immediately if
child consumes batteries.
Do not insert any metal objects/conductors (like a metal chopstick/
cutlery/screwdriver) between power cable plug and input Wall Socket
while it is connected to the input terminal on the wall. Additionally,
do not touch the power cable right after plugging into the wall input
terminal. You may be electrocuted. (Depending on model)
Do not put or store inammable substances near the product. There is a
danger of combustion/explosion or re due to careless handling of the
inammable substances.
Do not drop metallic objects such as coins, hair pins, chopsticks or wire
into the product, or inammable objects such as paper and matches.
Children must pay particular attention. Electrical shock, re or injury
can occur. If a foreign object is dropped into the product, unplug the
power cord and contact the service centre.
Do not spray water on the product or scrub with an inammable
substance (thinner or benzene). Fire or electric shock accident can
occur.
Do not allow any impact, shock or any objects to fall into the unit,
and do not drop anything onto the screen. You may be injured or the
product can be damaged.
Never touch this product or antenna during a thunder or lighting storm.
You may be electrocuted.
Never touch the wall outlet when there is leakage of gas, open the
windows and ventilate. It may cause a re or a burn by a spark.
4
ENGLISH
Do not disassemble, repair or modify the product at your own
discretion. Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
If any of the following occur, unplug the product immediately and
contact your local service centre.
•  The product has been impacted by shock
•  The product has been damaged
•  Foreign objects have entered the product
•  The product produced smoke or a strange smell
This may result in re or electric shock.
Unplug the TV from AC mains wall socket if you do not intend to use the
TV for a long period of time. Accumulated dust can cause re hazard
and insulation deterioration can cause electric leakage/shock/re.
Apparatus shall not be exposed to dripping or splashing and no objects
lled with liquids, such as vases, shall be placed on the apparatus.
Do not install this product on a wall if it could be exposed to oil or oil
mist. This may damage the product and cause it to fall.
If water enters or comes into contact with TV, AC adapter or power
cord please disconnect the power cord and contact service centre
immediately. Otherwise ,this may result in electric shock or re.
Only use an authorized AC adapter and power cord approved by
LG Electronics. Otherwise, this may result in re, electric shock,
malfunction or product deformation.
Never Disassemble the AC adapter or power cord.
This may result in re or electric shock.
Be careful in handling the adapter to prevent any external shocks to it.
An external shock may cause damage to the adapter.
Make sure the power cord is connected securely to the power plug on
the TV. (Depending on model)
CAUTION
Install the product where no radio wave occurs.
There should be enough distance between an outside antenna and
power lines to keep the former from touching the latter even when the
antenna falls. This may cause an electric shock.
Do not install the product on places such as unstable shelves or inclined
surfaces. Also avoid places where there is vibration or where the
product cannot be fully supported. Otherwise, the product may fall or
ip over, which may cause injury or damage to the product.
ENGLISH
5
If you install the TV on a stand, you need to take actions to prevent the
product from overturning. Otherwise, the product may fall over, which
may cause injury.
If you intend to mount the product to a wall, attach VESA standard
mounting interface (optional parts) to the back of the product. When
you install the set to use the wall mounting bracket (optional parts), x
it carefully so as not to drop.
Only use the attachments / accessories specied by the manufacturer.
When installing the antenna, consult with a qualied service
technician. If not installed by a qualied technician, this may create a
re hazard or an electric shock hazard.
We recommend that you maintain a distance of at least 2 to 7 times
the diagonal screen size when watching TV. If you watch TV for a long
period of time, this may cause blurred vision.
Only use the specied type of battery. This could cause damage to the
remote control.
Do not mix new batteries with old batteries. This may cause the
batteries to overheat and leak.
Batteries should not be exposed to excessive heat. For example, keep
away from direct Sunlight , open replace and electric heaters .
Do not place non-rechargeable batteries in charging device.
Make sure there are no objects between the remote control and its
sensor.
Signal from Remote Control can be interrupted due to external/internal
lighting eg Sunlight, uorescent lighting. If this occurs turn o lighting
or darken viewing area.
When connecting external devices such as video game consoles, make
sure the connecting cables are long enough. Otherwise, the product
may fall over, which may cause injury or damage the product.
Do not turn the product On/O by plugging-in or unplugging the power
plug to the wall outlet. (Do not use the power plug for switch.) It may
cause mechanical failure or could give an electric shock.
Please follow the installation instructions below to prevent the product
from overheating.
•  The distance between the product and the wall should be more
than 10cm.
•  Do not install the product in a place with no ventilation (e.g., on a
bookshelf or in a cupboard).
•  Do not install the product on a carpet or cushion.
•  Make sure the air vent is not blocked by a tablecloth or curtain.
Otherwise, this may result in re.
6
ENGLISH
Take care not to touch the ventilation openings when watching the TV
for long periods as the ventilation openings may become hot. This does
not aect the operation or performance of the product.
Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact replacement part
by an authorized servicer.
Prevent dust collecting on the power plug pins or outlet. This may cause
a re hazard.
Protect the power cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and the point where the cord
exits the appliance.
Do not press strongly upon the panel with a hand or sharp object such
as nail, pencil or pen, or make a scratch on it, as it may causedamage
to screen.
Avoid touching the screen or holding your nger(s) against it for long
periods of time. Doing so may produce some temporary or permanent
distortion/damage to screen.
When cleaning the product and its components, unplug the power
rst and wipe it with a soft cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with water or wipe with a wet
cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,
benzene, alcohol etc., which can damage the product and its panel.
Otherwise, this may result in re, electric shock or product damage
(deformation, corrosion or breakage).
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn o this unit
by SWITCH.
When unplugging the cable, grab the plug and unplug it, by pulling at
the plug.
Don’t pull at the cord to unplug the power cord from the power board,
as this could be hazardous.
When moving the product, make sure you turn the power o rst. Then,
unplug the power cables, antenna cables and all connecting cables.
The TV set or power cord may be damaged, which may create a re
hazard or cause electric shock.
When moving or unpacking the product, work in pairs because the
product is heavy. Otherwise, this may result in injury.
Refer all servicing to qualied service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
ENGLISH
7
If the product feels cold to the touch, there may be a small “icker”
when it is turned on. This is normal, there is nothing wrong with
product.
This panel is an advanced product that contains millions of pixels.
You may see tiny black dots and/or brightly coloured dots (white, red,
blue or green) at a size of 1ppm on the panel. This does not indicate a
malfunction and does not aect the performance and reliability of the
product.
This phenomenon also occurs in third-party products and is not subject
to exchange or refund.
You may nd dierent brightness and colour of the panel depending on
your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not
related with the product performance, and it is not malfunction.
Displaying a still image for a prolonged period of time may cause image
sticking. Avoid displaying a xed image on the TV screen for a long
period of time.
Some horizontal lines may appear when the Clear Panel Noise feature is
performed. It is normal and there is no need to be concerned.
Generated Sound
“Cracking noise: A cracking noise that occurs when watching or turning
o the TV is generated by plastic thermal contraction due to tempera-
ture and humidity. This noise is common for products where thermal
deformation is required. Electrical circuit humming/panel buzzing:
A low level noise is generated from a high-speed switching circuit,
which supplies a large amount of current to operate a product. It varies
depending on the product.
This generated sound does not aect the performance and reliability
of the product.
Do not use high voltage electrical goods near the TV(e.g. electric
mosquito-swatter). This may result in product malfunction.
Viewing 3D imaging (Only 3D
models)
CAUTION
•  Children should be supervised by an adult when viewing 3D video.
If a child experiences eye fatigue, headaches or blurred vision
while watching 3D, they should take a break, before they resume
watching 3D content.
•  When viewing a 3D video, some may experience discomfort such as
a headache, dizziness, fatigue, or blurred vision. In this case, stop
watching the 3D video and take a rest.
•  If you watch a 3D video for a long time, you may experience eye
fatigue. In this case, stop watching the 3D video and take a rest.
•  Only use LG 3D glasses. Otherwise, you may not be able to view 3D
videos properly.
•  Do not use 3D glasses instead of your normal glasses, sunglasses,
or protective goggles.
•  Do not keep your 3D glasses in extremely high or low
temperatures. It will cause deformation.
•  Do not use 3D glasses while walking or moving around. It may
cause an accident or injury.
•  Be careful not to poke your eye with the frames of the 3D glasses.
•  Do not watch 3D content if you have photosensitive seizures,
epilepsy, or heart disease.
Preparing
NOTE
•  If the TV is turned on for the rst time after it was shipped from the
factory, initialization of the TV may take a few minutes.
•  Image shown may dier from your TV.
•  Your TV’s OSD (On Screen Display) may dier slightly from that
shown in this manual.
•  The available menus and options may dier from the input source
or product model that you are using.
•  New features may be added to this TV in the future.
•  The items supplied with your product may vary depending on the
model.
•  Product specications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
•  For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not t into your TV’s USB port.
8
ENGLISH
A
B
A
B
*A
<
=
10 mm
*B
<
=
18 mm
•  Use a certied cable with the HDMI logo attached.
•  If you do not use a certied HDMI
cable, the screen may not display
or a connection error may occur. (Recommended HDMI
Cable Types)
- High-Speed HDMI
®
/
TM
Cable (3m or less)
- High-Speed HDMI
®
/
TM
Cable with Ethernet (3m or less)
CAUTION
•  Do not use any unapproved items to ensure the safety and product
life span.
•  Any damage or injuries caused by using unapproved items are not
covered by the manufacturer’s warranty.
•  Some models have a thin lm attached on to the screen and this
must not be removed.
•  When attaching the stand to the TV set, place the screen facing
down on a cushioned table or at surface to protect the screen
from scratches.
•  Make sure that the screws are fastened completely. (If they are
not fastened securely enough, the TV may tilt forward after being
installed.) Do not use too much force and over tighten the screws;
otherwise screw may be damaged and not tighten correctly.
•  Make sure to wring any excess water or cleaner from the cloth.
•  Do not spray water or cleaner directly onto the TV screen.
•  Make sure to spray just enough of water or cleaner onto a dry cloth
to wipe the screen.
Separate purchase
Separate purchase items can be changed or modied for quality
improvement without any notication. Contact your dealer to buy these
items. These devices only work with certain models.
The model name or design may be changed depending on the upgrade
of product functions, manufacturer’s circumstances or policies.
(Depending on model)
AG-F***
Cinema 3D Glasses
AN-MR650
Magic Remote
AG-F***DP
Dual Play Glasses
AN-VC550
Smart Camera
Lifting and moving the TV
Please note the following advice to prevent the TV from being scratched
or damaged and for safe transportation regardless of its type and size.
•  It is recommended to move the TV in the box or packing material
that the TV originally came in.
•  Before moving or lifting the TV, disconnect the power cord and
all cables.
•  When holding the TV, the screen should face away from you to
avoid damage.
•  Hold the top and bottom of the TV frame rmly. Make sure not to
hold the transparent part, speaker, or speaker grill area.
•  When transporting a large TV, there should be at least 2 people.
•  When transporting the TV by hand, hold the TV as shown in the
following illustration.
•  When transporting the TV, do not expose the TV to jolts or
excessive vibration.
•  When transporting the TV, keep the TV upright, never turn the TV
on its side or tilt towards the left or right.
•  Do not apply excessive pressure to cause exing /bending of frame
chassis as it may damage screen.
•  When handling the TV, be careful not to damage the protruding
buttons.
ENGLISH
9
CAUTION
•  Avoid touching the screen at all times, as this may result in damage
to the screen.
•  Do not move the TV by holding the cable holders, as the cable
holders may break, and injuries and damage to the TV may occur.
•  Make sure to attach the AV box xing supporter to the AV box
before you lift the product and move. Moving the product without
attaching the AV box xing supporter to the AV box rst may cause
injury to your ngers.
Using the button
You can simply operate the TV functions, pressing or moving the button.
Joystick Button
Basic functions
Power On (Press)
Power O (Press and hold)
1
Volume Control
Programmes Control
1 All running apps will close, and any recording in progress will stop.
Adjusting the menu
When the TV is turned on, press the button one time. You can adjust
the Menu items pressing or moving the buttons.
Turns the power o.
Clears on-screen displays and returns to TV viewing.
Changes the input source.
Accesses the settings menu.
Mounting on a table
1 Lift and tilt the TV into its upright position on a table.
•  Leave a 10 cm (minimum) space from the wall for proper
ventilation.
10 cm
10 cm
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
•  Do not place the TV near or on sources of heat, as this may result in
re or other damage.
Securing the TV to a wall
(This feature is not available for all models.)
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back
of the TV.
•  If there are bolts inserted at the eye-bolts position, remove the
bolts rst.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear
of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
Make sure to keep the rope horizontal with the at surface.
10
ENGLISH
CAUTION
•  Make sure that children do not climb on or hang on the TV.
NOTE
•  Use a platform or cabinet that is strong and large enough to
support the TV securely.
•  Brackets, bolts and ropes are not provided. You can obtain
additional accessories from your local dealer.
Mounting on a wall
Attach an optional wall mount bracket at the rear of the TV carefully
and install the wall mount bracket on a solid wall perpendicular to
the oor. When you attach the TV to other building materials, please
contact qualied personnel. LG recommends that wall mounting be
performed by a qualied professional installer.
We recommend the use of LG’s wall mount bracket. LG’s wall mount
bracket is easy to move with cables connected. When you do not use
LG’s wall mount bracket, please use a wall mount bracket where the
device is adequately secured to the wall with enough space to allow
connectivity to external devices. It is advised to connect all the cables
before installing xed wall mounts.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount bracket that meet the VESA
standard. Standard dimensions for the wall mount kits are described in
the following table.
Separate purchase(Wall mounting bracket)
Model OLED65G6* OLED77G6*
VESA (mm) (A x B) 400 x 200 600 x 300
Standard screw M6 M8 M4
Number of screws 4 4 2
Wall mount bracket OTW420B OTW630B
A
B
A
B
CAUTION
•  Fold the AV box or remove the stand before installing the TV on a
wall mount by performing the stand attachment in reverse.
•  To install the wall mount, switch the selector to
as
shown in the gure below. (Only OLED77G6*)
NOTE
•  Fold the AV box and attach the AV box xing supporter / Wall
mount spacer to the AV box before installing the product on a wall
mount. (Only when the item of the following form is provided)
Provided item
AV box xing supporter
x 2
1
2
ENGLISH
11
Provided item
AV box xing supporter /
Wall mount spacer
x 2
x 2
Wall mount spacer
x 2
Connections (notications)
Connect various external devices to the TV and switch input modes to
select an external device. For more information of external devices
connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio
systems, USB storage devices, PC, gaming devices, and other external
devices.
NOTE
•  The external device connection may dier from the model.
•  Connect external devices to the TV regardless of the order of the
TV port.
•  If you record a TV program on a DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder
or VCR. For more information of recording, refer to the manual
provided with the connected device.
•  Refer to the external equipment’s manual for operating
instructions.
•  If you connect a gaming device to the TV, use the cable supplied
with the gaming device.
•  In PC mode, there may be noise associated with the resolution,
vertical pattern, contrast or brightness. If noise is present, change
the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the PICTURE
menu until the picture is clear.
•  In PC mode, some resolution settings may not work properly
depending on the graphics card.
•  If ULTRA HD content is played on your PC, video or audio may
become disrupted intermittently depending on your PC’s
performance. (Depending on model)
Antenna connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
•  Use a signal splitter to use more than 2 TVs.
•  If the image quality is poor, install a signal amplier properly to
improve the image quality.
•  If the image quality is poor with an antenna connected, try to
realign the antenna in the correct direction.
•  An antenna cable and converter are not supplied.
•  Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,
HE-AAC
•  For a location that is not supported with ULTRA HD broadcasting,
this TV cannot receive ULTRA HD broadcasts directly. (Depending
on model)
Satellite dish connection
(Only satellite models)
Connect the TV to a satellite dish to a satellite socket with a satellite RF
cable (75 Ω).
CI module connection
(Depending on model)
View the encrypted (pay) services in digital TV mode.
•  Check if the CI module is inserted into the PCMCIA card slot in the
right direction. If the module is not inserted properly, this can
cause damage to the TV and the PCMCIA card slot.
•  If the TV does not display any video and audio when CI+ CAM is
connected, please contact to the Terrestrial/Cable/Satellite Service
Operator.
USB connection
Some USB Hubs may not work. If a USB device connected through a USB
Hub is not detected, connect it directly to the USB port on the TV.
12
ENGLISH
Other connections
Connect your TV to external devices. For the best picture and audio
quality, connect the external device and the TV with the HDMI cable.
Some separate cable is not provided.
• 
General HDMI ULTRA HD Deep
Colour :
- On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)
- Off : Support 4K @ 50/60 Hz 8 bit (4:2:0)
If the device connected to Input Port also supports ULTRA HD Deep
Colour, your picture may be clearer.
However, if the device doesn’t support it, it may not work properly.
In that case, connect the device to a different HDMI port or change the
TV’s HDMI ULTRA HD Deep Colour setting to Off.
(This feature is available on certain models which are supported ULTRA
HD Deep Colour only.)
NOTE
•  Supported HDMI Audio format :
Dolby Digital (32 kHz, 44.1 kHz, 48 kHz),
DTS (44.1 kHz, 48 kHz),
PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz)
(Depending on model)
Slim remote control
(Depending on model)
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
To replace coin batteries, turn the battery cover counterclockwise by
using a coin. Take the battery cover o and insert the battery (CR2032)
facing forward
. Put the battery cover on the remote control and
turn it clockwise to close. To remove the coin batteries, perform the
installation actions in reverse.
Make sure to point the remote control toward the remote control sensor
on the TV.
EXIT
BACK
STB
PWR
A
B
A
(POWER) Turns the TV on or o.
You can turn your set-top box on or o by adding the
set-top box to the universal remote control for your TV.
Adjusts the volume level.
Scrolls through the saved programmes.
(MUTE) Mutes all sounds.
* By pressing and holding the
button, audio descriptions
function will be enabled. (Depending on model)
B
Returns to the previous level.
Clears on-screen displays and returns to last input viewing.
(HOME) Accesses the Home menu.
(INPUT) Changes the input source.
* Pressing and holding the
button displays all the lists of
external inputs.
Selects menus or options and conrms your input.
Navigation buttons (up/down/left/right)
Press the up, down, left or right button to scroll the menu.
Battery installation
WARNING
DO NOT INGEST BATTERY. CHEMICAL BURN HAZARD.
CAUTION
•  The battery used in this device may present a re or chemical burn
hazard if mistreated. Do not recharge, disassemble, incinerate, or
heat above 100 °C. Replace the battery part no. CR2032 only. Use of
another battery may present a risk of re or explosion. Dispose of
used battery. Keep battery away from children. Do not disassemble
or dispose of in re.
•  [The remote control supplied with] This product contains a coin/
button cell battery. If the coin/button cell battery is swallowed,
it can cause severe internal burns in just 2 hours and can lead to
death. Keep new and used batteries away from children. If the
battery compartment does not close securely, stop using the
product and keep it away from children. If you think batteries
might have been swallowed or placed inside any part of the body,
seek immediate medical attention.
•  If you have long nails, do not open the battery cover by using your
nger. Or else, your nail could break.
ENGLISH
13
Magic remote functions
(Depending on model)
When the message “Magic remote battery is low. Change the battery. is
displayed, replace the battery.
To replace batteries, open the battery cover, replace batteries (1.5 V AA)
matching the
and ends to the label inside the compartment,
and close the battery cover. Be sure to point the magic remote toward
the remote control sensor on the TV. To remove the batteries, perform
the installation actions in reverse.
GUIDE
LIST
STB
TEXT
T.OPT
FOCUS
MENU
RECENT
EXIT
BACK
LIVE ZOOM
STB
PWR
6
mno
9
wxyz
3
def
2
abc
1
. @
4
ghi
8
tuv
7
pqrs
0
5
jkl
/
/
A
B
A
(POWER) Turns the TV on or o.
You can turn your set-top box on or o by adding the
set-top box to the universal remote control for your TV.
Number buttons Enters numbers.
(Space) Opens an empty space on the screen keyboard.
Accesses the saved programmes list.
(Screen Remote) Displays the Screen Remote.
*Accesses the Universal Control Menu. (Depending on model)
B
Adjusts the volume level.
P Scrolls through the saved programmes.
(MUTE) Mutes all sounds.
* By pressing and holding the
button, audio descriptions
function will be enabled. (Depending on model)
(SEARCH) Search for content such as TV programmes, movies
and other videos, or perform a web search by entering text in the
search bar.
(Voice recognition) (Depending on model)
Network connection is required to use the voice recognition function.
1. Press the voice recognition button.
2. Speak when the voice display window appears on the TV screen.
C
D
C
(HOME) Accesses the Home menu.
Shows the previous history.
Displays the set-top box Home menu.
* When you are not watching via a set-top box: the display changes
to the set-top box screen.
Wheel (OK) Press the center of the Wheel button to select a
menu. You can change programmes by using the wheel button.
Navigation buttons (up/down/left/right)
Press the up, down, left or right button to scroll the menu.
If you press
buttons while the pointer is in use, the
pointer will disappear from the screen and Magic Remote will
operate like a general remote control. To display the pointer on the
screen again, shake Magic Remote to the left and right.
Returns to the previous level.
Clears on-screen displays and returns to last input viewing.
Shows programmes guide.
D
Used for viewing 3D video. (Only 3D models)
(INPUT) Changes the input source.
* Pressing and holding the button displays all the lists of
external inputs.
(Q. Settings) Accesses the Quick Settings.
* Pressing and holding the
button displays the All Settings
menu.
TELETEXT buttons (
, )
These buttons are used for
teletext.
Views the information of the current programme and
screen.
Control buttons (
) Controls media contents.
You can zoom in on the area where the remote control is
pointed.
By zooming in on the selected area, you can view it in
full screen.
Coloured buttons These access special functions in some menus.
(
: Red, : Green, : Yellow, : Blue)
14
ENGLISH
Registering magic remote
How to register the magic remote
To use the Magic Remote, rst pair it with your TV.
1 Put batteries into the Magic Remote and turn the TV on.
2 Point the Magic Remote at your TV and press the
Wheel (OK) on
the remote control.
* If the TV fails to register the Magic Remote, try again after turning the
TV o and back on.
How to deregister the magic remote
Press the and (HOME) buttons at the same time, for ve
seconds, to unpair the Magic Remote with your TV.
* Pressing and holding the
button will let you cancel and re-
register Magic Remote at once.
Licenses
Supported licenses may dier by model. For more information about
licenses, visit www.lg.com.
Open source software
notice information
To obtain the source code under GPL, LGPL, MPL, and other open source
licenses, that is contained in this product, please visit http://opensource.
lge.com.
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
as the cost of media, shipping, and handling) upon email request to
[email protected]om. This oer is valid for three (3) years from the date
on which you purchased the product.
External control device
setup
To obtain the external control device setup information, please visit
www.lg.com.
Troubleshooting
Cannot control the TV with the remote control.
•  Check the remote control sensor on the product and try again.
•  Check if there is any obstacle between the product and the remote
control.
•  Check if the batteries are still working and properly installed (
to , to ).
No image display and no sound is produced.
•  Check if the product is turned on.
•  Check if the power cord is connected to a wall outlet.
•  Check if there is a problem in the wall outlet by connecting other
products.
The TV turns o suddenly.
•  Check the power control settings. The power supply may be
interrupted.
•  Check if the Sleep Timer / Timer Power Off is activated in the
TIMERS settings.
•  Check if the Auto Power O is activated in the General
ECO
MODE settings. (Depending on model)
•  If there is no signal while the TV is on, the TV will turn o
automatically after 15 minutes of inactivity.
When connecting to the PC (HDMI), ‘No signal’ or ‘Invalid Format’ is
displayed.
•  Turn the TV o/on using the remote control.
•  Reconnect the HDMI cable.
•  Restart the PC with the TV on.
Specications
Wireless module specication
•  As band channels can vary per country, the user cannot change or
adjust the operating frequency. This product is congured for the
regional frequency table.
•  For consideration of the user, this device should be installed and
operated with a minimum distance of 20 cm between the device
and the body.
ENGLISH
15
Wireless module (LGSBWAC61) Specifications
Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency range Output power(Max.)
2400 to 2483.5 MHz
5150 to 5725 MHz
5725 to 5850 MHz (Not for EU)
15.5 dBm
17.5 dBm
8.0 dBm
Bluetooth
Frequency range Output power(Max.)
2400 to 2483.5 MHz 10 dBm
* ‘IEEE802.11ac is not available in all countries.
CI Module (W x H x D) 100.0 mm x 55.0 mm x 5.0 mm
Environment
condition
Operating
Temperature
0 °C to 40 °C
Operating
Humidity
Less than 80 %
Storage
Temperature
-20 °C to 60 °C
Storage
Humidity
Less than 85 %
(Depending on country)
Digital TV Analogue TV
Satellite Terrestrial Cable Terrestrial / Cable
Television system DVB-S/S2*
DVB-T
DVB-T2*
DVB-C
PAL/SECAM B/G, D/K, I,
SECAM L
Channel coverage
(Band)
950~2150MHz
VHF III : 174 ~ 230MHz
UHF IV : 470 ~ 606MHz
UHF V : 606 ~ 862MHz
S Band II : 230 ~ 300MHz
S Band III : 300 ~ 470MHz
46 ~ 862MHz 46 ~ 862MHz
Maximum number of
storable programmes
6,000 3,000
External antenna impedance 75 Ω
* Only DVB-T2/C/S2 support model only.
Bitte lesen Sie dieses Handbuch aufmerksam durch, bevor Sie Ihr
Gerät zum ersten Mal verwenden und bewahren Sie es zur späteren
Verwendung auf.
www.lg.com
Sicherheitshinweise und Referenzen
2
DEUTSCH
Sicherheitshinweise
Bevor Sie das Produkt zum ersten Mal verwenden,
lesen Sie diese Sicherheitshinweise bitte
aufmerksam durch.
WARNUNG
Stellen Sie das TV-Gerät mit Fernsteuerung nicht in folgenden
Umgebungen auf:
•  Unter direkter Sonneneinstrahlung
•  In Bereichen mit hoher Luftfeuchtigkeit, wie z. B. einem
Badezimmer
•  In der Nähe von Hitzequellen, wie z. B. Öfen und anderen
hitzeerzeugenden Geräten
•  In der Nähe von Küchenzeilen oder Befeuchtern, wo das Gerät
leicht Dampf oder Öl ausgesetzt sein kann
•  In Bereichen, die Regen oder Wind ausgesetzt sind
•  In der Nähe von Behältern mit Wasser, wie z. B. Vasen
Andernfalls kann es zu Bränden, Stromschlägen, Fehlfunktionen oder
Produktverformungen kommen.
Schützen Sie das Gerät vor Staub. Es besteht Brandgefahr.
Wenn Sie das Gerät vom Stromnetz trennen möchten, müssen Sie den
Netzstecker aus der Steckdose ziehen. Dieser Stecker muss jederzeit gut
zugänglich sein.
Berühren Sie den Netzstecker nicht mit nassen Händen. Wenn die
Kontaktstifte nass oder verstaubt sind, trocknen Sie den Netzstecker
vollständig ab, bzw. befreien Sie ihn von Staub.
Feuchtigkeit erhöht die Gefahr eines tödlichen Stromschlags.
Stellen Sie sicher, dass das Stromkabel geerdet ist. (Außer bei Geräten,
die nicht geerdet sind.)
Bei Nichtbeachtung besteht die Gefahr von Verletzungen oder eines
tödlichen Stromschlags.
Das Stromkabel muss vollständig in die Steckdose eingesteckt werden.
Ist das Stromkabel nicht fest in die Steckdose eingesteckt, besteht
Brandgefahr.
Das Stromkabel darf nicht mit heißen Gegenständen wie einem
Heizkörper in Berührung kommen.
Andernfalls bestehen Brandgefahr und die Gefahr von Stromschlägen.
Stellen Sie keinen schweren Gegenstand oder das Gerät selbst auf
das Stromkabel. Andernfalls kann es zu Bränden und Stromschlägen
kommen.
Platzieren Sie das Antennenkabel zwischen dem Innen- und
Außenbereich des Gebäudes so, dass kein Regen hereinießen kann.
Etwaiger Wassereintritt kann zu Schäden am Gerät und Stromschlag
führen.
Falls das TV-Gerät an der Wand montiert wird, darf es nicht an den
Strom- und Signalkabeln auf der Rückseite des TV-Gerätes aufgehängt
werden.
Anderenfalls besteht die Gefahr von Bränden oder Stromschlägen.
DEUTSCH
3
Schließen Sie nicht zu viele Elektrogeräte an einer einzelnen Steckdose
an. Andernfalls kann es aufgrund von Überhitzung zu Bränden
kommen.
Lassen Sie das Gerät beim Anschluss eines externen Gerätes nicht
fallen. Andernfalls können Verletzungen verursacht oder das Gerät
beschädigt werden.
Desiccant
Bewahren Sie das Trockengranulat und die Vinyl-Verpackung außerhalb
der Reichweite von Kindern auf.
Trockengranulat ist bei Verschlucken gesundheitsschädlich. Falls es
verschluckt wurde, Erbrechen herbeiführen und die Person ins nächste
Krankenhaus bringen. Außerdem besteht Erstickungsgefahr durch die
Vinyl-Verpackung. Bewahren Sie sie außerhalb der Reichweite von
Kindern auf.
Achten Sie darauf, dass sich Kinder nicht an das TV-Gerät hängen oder
daran hochklettern.
Andernfalls kann das Gerät umfallen, wodurch schwere Verletzungen
hervorgerufen werden können.
Leere Batterien müssen sicher entsorgt werden, um zu verhindern, dass
Kinder sie verschlucken.
Wenn ein Kind eine Batterie verschluckt hat, sofort den Arzt aufsuchen.
Berühren Sie das Ende des Netzkabels nicht mit einem leitenden
Gegenstand (wie einer Gabel), während das Netzkabel mit der
Steckdose verbunden ist. Berühren Sie das Netzkabel nicht, kurz
nachdem Sie es mit der Steckdose verbunden haben.
Es besteht die Gefahr eines tödlichen Stromschlags.
(Abhängig vom Modell)
Bringen Sie keine entammbaren Stoe in die Nähe des Gerätes.
Bei unsachgemäßem Umgang mit entammbaren Stoen besteht
Explosionsgefahr.
Es dürfen keine Metallgegenstände wie Münzen, Haarnadeln,
Besteck oder Draht bzw. entzündliche Gegenstände wie Papier oder
Streichhölzer in das Gerät gelangen. Achten Sie insbesondere auf
Kinder.
Es besteht die Gefahr von Stromschlag, Brand oder Verletzung. Wenn
ein Gegenstand in das Gerät gelangt, ziehen Sie das Stromkabel, und
wenden Sie sich an den Kundendienst.
Sprühen Sie kein Wasser auf das Produkt, und bringen Sie es nicht mit
entzündlichen Stoen (Verdünnungsmittel oder Benzol) in Verbindung.
Es besteht Stromschlag- und Brandgefahr.
Setzen Sie das Produkt keinen Schlägen und Stößen aus. Sorgen Sie
dafür, dass keine Gegenstände auf das Gerät oder den Bildschirm fallen.
Es besteht Verletzungsgefahr. Außerdem kann das Produkt beschädigt
werden.
Berühren Sie das Produkt oder die Antenne nicht während eines
Gewitters. Es besteht die Gefahr eines tödlichen Stromschlags.
Im Falle eines Gasaustritts berühren Sie keinesfalls die Steckdose.
Önen Sie zum Lüften die Fenster.
Durch Funken können ein Brand oder Verbrennungen hervorgerufen
werden.
4
DEUTSCH
Sie dürfen das Gerät nicht eigenmächtig auseinanderbauen, reparieren
oder verändern. Es besteht Stromschlag- und Brandgefahr.
Wenden Sie sich zur Überprüfung, Kalibrierung oder Reparatur an den
Kundendienst.
Ziehen Sie in jedem der folgenden Fälle sofort den Netzstecker, und
setzen Sie sich mit Ihrem Kundendienst vor Ort in Verbindung.
•  Das Gerät wurde einer Erschütterung ausgesetzt
•  Das Gerät wurde beschädigt
•  Fremdkörper sind in das Gerät gelangt
•  Vom Gerät sind Rauch oder ungewöhnliche Gerüche ausgegangen
Dies kann Brand oder Stromschlag verursachen.
Ziehen Sie das Stromkabel aus der Steckdose, wenn das Gerät für
längere Zeit nicht verwendet wird.
Wenn das Gerät eingestaubt ist, besteht Brandgefahr. Ein Verschleiß der
Isolation kann zu Kriechverlust, Stromschlag oder Brand führen.
Achten Sie darauf, dass keine Flüssigkeit auf das Gerät spritzt oder
tropft. Stellen Sie keine Gegenstände, die Flüssigkeiten enthalten (z. B.
Vasen), auf dem Gerät ab.
Installieren Sie dieses Produkt nicht an Wänden, falls es dadurch Öl oder
Ölnebel ausgesetzt werden könnte. Dies kann zu Schäden am Produkt
führen oder das Produkt könnte sich lösen.
Wenn Wasser oder eine andere Substanz in das Produkt (z.B.
Netzadapter, Netzkabel, TV-Gerät) eindringen, ziehen Sie das Netzkabel
ab, und kontaktieren Sie unverzüglich den Kundendienst. Andernfalls
kann es zu einem Brand oder Stromschlag kommen.
Verwenden Sie nur autorisierte Netzadapter und Netzkabel, die von
LGElectronics genehmigt wurden. Andernfalls kann es zu Bränden,
Stromschlägen, Fehlfunktionen oder Produktverformungen kommen.
Nehmen Sie den Netzadapter und das Netzkabel nicht auseinander.
Andernfalls kann es zu einem Brand oder Stromschlag kommen.
Im Umgang mit dem Adapter ist Vorsicht geboten– vermeiden Sie
externe Erschütterungen am Adapter.
Externe Erschütterungen können zu Schäden am Adapter führen.
Stellen Sie sicher, dass das Netzkabel sicher mit dem Netzstecker des
TV-Geräts verbunden ist. (Abhängig vom Modell)
VORSICHT
Stellen Sie das Gerät nicht in der Nähe von Funkwellen auf.
Der Abstand zwischen einer Außenantenne und Stromleitungen muss
groß genug sein, um eine Berührung der beiden zu verhindern, selbst
wenn die Antenne herunterfällt.
Andernfalls besteht die Gefahr von Stromschlägen.
Stellen Sie das Produkt nicht auf unstabilen Regalen oder geneigten
Oberächen auf. Vermeiden Sie außerdem Stellplätze, die vibrieren
oder auf denen das Produkt keinen sicheren Halt hat.
Andernfalls kann das Gerät herunter- oder umfallen, wodurch
Verletzungen oder Beschädigungen am Gerät verursacht werden
können.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

LG OLED65G6V Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues