Frigidaire FASG7073LA0 Guide d'installation

TABLE OF

Important Safety Instructions .............................. 2_3

Installation Requirements ................................. 4_10

Installed Dryer Dimensions .................................. !::[

Installation Instructions .................................. 12-17

CONTENTS

Espaff01.................................. 45

o

CD

>

For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent

property damage, personal injury or loss of life. Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

A WARNING - RISK OF FIRE

Read all of the following instructions before installing and using this appliance:

- Destroy the carton and plastic bags after the dryer is unpacked. Children might use them for play. Cartons covered

with rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Place all materials in a

garbage container or make materials inaccessible to children.

Clothes dryer installation and service must be performed by a qualified installer, service agency or the gas supplier.

Install the clothes dryer according to the manufacturer's instructions and local codes.

The electrical service to the dryer must conform with local codes and ordinances and the latest edition of the Na-

tional Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian electrical code C22.1 part 1.

The gas service to the dryer must conform with local codes and ordinances and the latest edition of the National

Fuel Gas Code ANSI Z223.1, or in Canada, CAN/ACG B149.1-2000.

The dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 No. 112 (latest editions) for HONE

USE only. This dryer is not recommended for commercial applications such as restaurants, beauty salons, etc.

Do not install a clothes dryer with flexible plastic venting material. Flexible venting materials are known to collapse,

be easily crushed and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.

Do not stack a dryer on top of washer already installed on pedestal. Do not stack dryer on top of another dryer. Do

not stack washer on top of dryer. Do not stack washer on top of another washer.

The instructions in this manual and all other literature included with this dryer are not meant to cover every pos-

sible condition and situation that may occur. Good safe practice and caution MUST be applied when installing,

operating and maintaining any appliance.

WHAT TO DO IF YOU SMELL GAS:

- Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Clear the room, building or area of all occupants.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire department.

Save these instructionsfor future reference.

Pre-Installation Requirements

Tools and materials needed for installation:

- Adjustable pliers

- Phillips, straight, & square bit

screwd rivers

Adjustable wrench

Pipe wrench for gas supply (gas

dryer)

LP-resistant thread tape (for natu-

ral gas or LP supply, gas dryer)

- Carpenter's level

- External vent hood

- 4-inch (102 mm), rigid metal or

semi-rigid metal exhaust duct work

3-wire or 4-wire 240 volt cord kit

(electric dryer)

4 in. (10.2 cm) clamp

- Gas line shutoff valve (gas dryer)

- 1/2NPT union flare adapters (x2)

and flexible gas supply line (gas

dryer)

Metal foil tape (not duct tape)

Pleasereadallinstructionsbeforeusingthisdryer.

Recognize safety symbols, words and

labels

Safety items throughout this manual are labeled with

a WARNING or CAUTION based on the risk type as

described below:

Definitions

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible injury

or death.

DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious

injury,

WARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

IMPORTANT indicates installation, operation or

maintenance information which is important but not

hazard-related,

Exhaust Venting

[] Free-flowing, clear of lint buildup

[] 4 inch (102 mm) rigid or semi-rigid ducting of

minimal length and turns

[] NO foil or plastic venting material

[] Approved vent hood exhausted to outdoors

Leveling

[] Dryer is level, side=to-side and front-to-back

[] Cabinet is setting solid on all corners

Gas Supply (Gas Dryer)

[] Manual shutoff valve present in supply

[] All connections sealed with approved sealer

and wrench tight

[] Conversion kit for LP system

[] Gas supply turned on

[] No leaks present at all connections -

check with soapy water, NEVERcheck with

flame

240v Electric Supply (Electric Dryer)

[] Approved NEMA 10-30R or 14-30R service

cord with all screws tight on terminal block

[] Approved strain relief installed

[] Terminal access cover installed before initial

operation

Door Reversal

[] Follow detailed instructions in this guide

[] Test hinge and latch for function

Electrical Power

[] House power turned on

[] Dryer plugged in

Final Checks

[] Installation Instructions and Use and

Care Guide read thoroughly

[] Door latches and drum tumbles when cycle

starts

[] Registration card sent in

Electrical requirements for electric dryer

CIRCUIT - Individual 30 amp. branch circuit fused with 30 amp. time delay fuses or circuit breakers. Use separately

fused circuits for washer and dryer. DO NOT operate a washer and a dryer on the same circuit.

POWER SUPPLY- 3-wire or 4-wire, 240 volt, single phase, 60 Hz, Alternating Current.

This dryer is internally grounded to neutral unless it was manufactured for sale in Canada.

Only a 4-conductor cord shall be used when the appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the neutral link is prohibited for: (1) new branch circuit

installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes do not permit grounding

OUTLET RECEPTACLE- NEMA 10-30R or NEMA 14-30R receptacle to be located so the power supply cord is accessible

when the dryer is in the installed position.

GROUNDING CONNECTION - See "Grounding requirements" in Electrical Installation section.

3-WIRE POWER SUPPLYCORD KIT (not supplied)

3-wire receptacle

(NEMA type 10=30R)

The dryer MUST employ a 3-conductor power

supply cord NENA 10-30 type SRDT rated at 240

volt AC minimum, 30 amp, with 3 open end spade

lug connectors with upturned ends or closed

loop connectors and marked for use with clothes

dryers. For 3-wire cord connection instructions see

ELECTRICALCONNECTIONS FOR A 3-WIRE SYSTEM.

4-WIRE POWER SUPPLYCORD KIT (not supplied)

4-wire receptacle

(NEMA type 14=30R)

The dryer MUST employ a 4-conductor power supply

cord NEMA 14-30 type SRDT or ST (as required) rated

at 240 volt AC minimum, 30 amp, with 4 open end

spade lug connectors with upturned ends or closed

loop connectors and marked for use with clothes

dryers. For4-wire cord connection instructions see

ELECTRICAL CONNECTIONS FOR A 4-WIRE SYSTEM.

Dryers manufactured for sale in Canada have factory-

installed, 4:w! re power Supply €ord (NEMA 14:30R):..................................

Electrical requirements for gas dryer

CIRCUIT - Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay

fuse or circuit breaker.

POWER SUPPLY- 2-wire, with ground, 120 volt, single

phase, 60 Hz, Alternating Current.

POWER SUPPLYCORD - The dryer is equipped with a 120

volt 3-wire power cord.

GROUNDING CONNECTION - See "Grounding

requirements" in Electrical Installation section.

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

Powercord with

3-prong grounded plug

Gas supply requirements

1 Installation MUST conform with local codes, or in

the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1 (latest edition).

2 The gas supply line should be 1/2 inch (1.27 cm)

pipe.

3 If codes allow, flexible metal tubing may be used

to connect your dryer to the gas supply line. The

tubing MUST be constructed of stainless steel or

plastic-coated brass.

4 The gas supply line MUST have an individual

shutoff valve.

5 A 1/8 inch (0.32 cm) N.RT. plugged tapping,

accessible for test gauge connection, MUST be

installed immediately upstream of the gas supply

connection to the dryer.

6 The dryer MUST be disconnected from the gas

supply piping system during any pressure testing

of the gas supply piping system at test pressures in

excess of 1/2 psig (3.45 kPa).

7 The dryer MUST be isolated from the gas supply

piping system during any pressure testing of the

gas supply piping system at test pressures equal to

or less than 1/2 psig (3.45 kPa).

8 Connections for the gas supply must comply with

the Standard for Connectors for Gas Appliances,

ANSI Z21.24.

Exhaust system requirements

Use only 4 inch (102 mm) diameter rigid or flexible metal

duct and approved vent hood which has a swing-out

damper(s) that open when the dryer is in operation.

When the dryer stops, the dampers automatically close to

prevent drafts and the entrance of insects and rodents.

To avoid restricting the outlet, maintain a minimum of 12

inches (30.5 cm) clearance between the vent hood and

the ground or any other obstruction.

FIRE HAZARD

Failure to follow these instructions can create excessive

drying times and fire hazards.

The following are specific requirements for

proper and safe operation of your dryer.

FIRE HAZARD

Do not install a clothes dryer with flexible plastic or

metal foil venting materials. Flexibleventing materials

are known to collapse, be easily crushed and trap lint.

These conditions will obstruct clothes dryer airflow and

increase the risk of fire:...........................................................................................................................................................................................................

:If your present system is made up of plastic duct or

metal foil duct, replace it with a rigid or semi-rigid metal

duct. Also, ensure the present duct is free of any lint prior

to installing dryer duct.

f

Correct

1i

Incorrect

Exhaust system requirements, continued

FIRE HAZARD

A clothes dryer must be exhausted outdoors. Do not

exhaust dryer into a chimney, a wall, a ceiling, an attic,

a crawl space or any concealed space of a building. A

clothes dryer produces combustible lint. If the dryer is

not exhausted outdoors, some fine lint will be expelled

into the laundry area. An accumulation of lint in any

area of the home can create a health and fire hazard.

The dryer must be connected to an exhaust outdoors.

Regularly inspect the outdoor exhaust opening and

remove any accumulation of lint around the outdoor

exhaust opening and in the surrounding area.

FIRE HAZARD

- Do not allow combustible materials (for example:

clothing, draperies/curtains, paper) to come in

contact with exhaust system. The dryer MUST NOT

be exhausted into a chimney, a wall, a ceiling,

or any concealed space of a building which can

ii

accumulate lint, resulting in a fire hazard.

- Do not screen the exhaust ends of the vent system,

or use any screws, rivets or other fasteners that

extend into the duct to assemble the exhaust

system. Lint can become caught in the screen, on

the screws or rivets, clogging the duct work and

ii

creating a fire hazard as well as increasing drying

ii

times. Use an approved vent hood to terminate the

duct outdoors, and seal all joints with metal foil duct

tape. All male duct pipe fittings MUST be installed

downstream with the flow of air.

FIRE HAZARD

Exceeding the length of duct pipe or number of elbows

allowed in the "MAXIMUM LENGTH" charts can cause

an accumulation of lint in the exhaust system. Plugging

the system could create a fire hazard, as well as

z

€-

3

o

E

S

go

MAXIMUM LENGTH

of 4" (102mm) Rigid Metal Duct

VENT HOOD TYPE

(Preferred)

(10.2cm) Iouvered

64 ft. (19.5 m)

2.5"

(6.35cm)

48 ft. (14.6 m)

0

1 52 ft. (15.9 m) 40 ft. (12.2 m)

2 44 ft. (13.5 m) 32 ft. (9.8 m)

3 32 ft. (9.8 m) 24 ft. (7.3 m)

4 28 ft. (9.5 m) 16 ft. (4.9 m)

FIRE HAZARD

- Do not install flexible plastic or flexible foil venting

material.

- If installing semi-rigid venting, do not exceed 8 ft.

Exhaust system requirementsr continued

Install male fittings in correct direction"

CORRECT iNCORRECT

In installations where the exhaust system is not described

in the charts, the following method must be used to

determine if the exhaust system is acceptable:

:[ Connect an inclined or digital manometer between

the dryer and the point the exhaust connects to the

dryer.

2 Set the dryer timer and temperature to air fluff

(cool down) and start the dryer.

3 Read the measurement on the manometer.

4 The system back pressure MUST NOT be higher

than 0.75 inches of water column. If the

system back pressure is less than 0.75 inches of

water column, the system is acceptable. If the

manometer reading is higher than .075 inches of

water column, the system is too restrictive and the

installation is unacceptable.

Although vertical orientation of the exhaust system is

acceptable, certain extenuating circumstances could

affect the performance of the dryer:

o Only the rigid metal duct work should be used.

Venting vertically through a roof may expose the

exhaust system to down drafts causing an increase

in vent restriction.

Running the exhaust system through an

uninsulated area may cause condensation and

faster accumulation of lint.

Compression or crimping of the exhaust system will

cause an increase in vent restriction.

The exhaust system should be inspected and

cleaned a minimum of every 18 months with

normal usage. The more the dryer is used, the

more often you should check the exhaust system

and vent hood for proper operation.

Exhaust direction

Directional exhausting can be accomplished by installing

a quick-turn 90° dryer vent elbow directly to exhaust

outlet of dryer. Dryer vent elbows are available through

your local parts distributor or hardware store.

See also CLEARANCE REQUIREMENTS on the next page.

Use of 90° quick-turn elbow required to meet minimum

installation depth of free-standing dryer:

• Straight back venting allows for 0" (0 cm) installation.

Venting right with 90° elbow allows for 0.75" (2 cm)

installation.

Venting downward with 90° elbow allows for 0.75" (2

cm) installation.

Venting left with short, straight adapter and 90°

elbow allows for 3.75" (9.5 cm) installation.

Venting upward with short, straight adapter and 90°

.......................e/bow a!!ows for 4" (10-5 cm) !nsta/lat!on- ..............................................................................

Manufactured or mobile home installation

1 Installation MUST conform to current Manufactured

Home Construction & Safety Standard, Title 24

CFR, Part 32-80 (formerly the Federal Standard

for Mobile Home Construction and Safety, Title 24,

HUD Part 280) or Standard CAN/CSAZ240 MH.

2 Dryer MUST be exhausted outside (outdoors, not

beneath the mobile home) using metal ducting

that will not support combustion. Metal ducting

must be 4 inches (10.16 cm) in diameter with no

obstructions. Rigid metal duct is preferred.

3 If dryer is exhausted through the floor and area

beneath the mobile home is enclosed, the exhaust

system MUST terminate outside the enclosure with

the termination securely fastened to the mobile

home structure.

4 Refer to previous sections in this guide for other

important exhaust venting system requirements.

5 When installing a gas dryer into a mobile home, a

provision must be made for outside make up air.

This provision is to be not less than twice the area

of the dryer exhaust outlet.

6 Installer MUST anchor this (1) dryer or (2) dryer

mounted on pedestal to the floor with approved

Mobile Home Installation Kit - P/N 137067200.

Clearance requirements

EXPLOSION HAZARD

Do not install the dryer where gasoline or other

flammables are kept or stored. If the dryer is installed

in a garage, it must be a minimum of 18 inches (45.7

cm) above the floor. Failure to do so can result in

death, explosion, fire or burns.

NOT INSTALL YOUR DRYER:

1 In an area exposed to dripping water or outside

weather conditions.

2 In an area where it will come in contact with

curtains, drapes, or anything that will obstruct

the flow of combustion and ventilation air.

3 On carpet. Floor MUST be solid with a maximum

slope of 1 inch (2.54 cm).

Clearance requirements, continued

Installation in a Recess or Closet

:[ A dryer installed in a bedroom, bathroom, recess or

closet, MUST be exhausted outdoors.

2 No other fuel burning appliance shall be installed in

the same closet as the gas dryer.

3 Your dryer needs the space around it for proper

ventilation.

DO NOT install your dryer in a closet with a solid door.

4 Closet door ventilation required: A minimum

of 120 square inches (774.2 cm 2) of opening,

equally divided at the top and bottom of the

door, is required. Openings should be located 3

inches (7.6 cm) from bottom and top of door.

Openings are required to be unobstructed when a

door is installed. A Iouvered door with equivalent

air openings for the full length of the door is

acceptable.

3"

(7.6c m]

closet door

-1--

60 sq. in.

(387.1cm =)

f

60 sq. in.

(387.1cm _)

MINIMUM INSTALLATION CLEARANCES- Inches (cm)

SIDES REAR TOP FRONT

Alcove _ " )" 0"

_0 (0 cm) (0 cm)* (0 cm) n/a

Under- 0" (0 cm) :)" (0 cm) * 0" (0 cm) n/a

Counter

Closet _ " :)" 0" 1"

!0 (0 cm) (0 cm)* (0 cm) (2.54 cm)

Dryer must be vented straight back to achieve

0" (0 cm) rear installation.

©

O" t

(Ocm)

51.4" (131cm)

freestanddryer

on floor

floorline

dryer mounted on

op_onalpedes_l

floorline

30.3"(77cm)*

to front of closed door

* To obtain these minimal depth dimensions, dryer must be vented straight back. Using a quick-turn 90°

elbow (right or down on freestanding dryer) adds approximately 0.75 in. (2.0 cm) to installation depth.

Upward venting of exhaust on pedestal-mounted or freestanding dryer adds approximately 4 in. (10.2 cm) to

installation depth. Leftward venting on pedestaFmounted or freestanding dryer adds approximately 3.75 in.

(9.5 cm) to installation depth. Downward venting of exhaust on pedestal-mounted dryer adds approximately

2.25 in. (5.7 cm) to installation depth.

gas supply

pipe on rear

of gas unit

51.25"

(130cm)

[

36.0"

(91.5cm)

16.9"

(43cm)

3.75"

(9.5cm)

27.0"

(68.5cm)

©

electrical

supply on

rear of unit

centerline

height for

rear vent

(34.5cm)

to center of rear vent

51,4" (131cm)

to clear open door

30.3" (77cm)*

to front of closed door

71.5"

(182cm)

water supply

connection on

rear of unit1

gas supply

pipe on rear

of gas unit

37"

(94cm)

27.0"

(68.5cm)

0

drain hose on

rear of unit3

electrical

supply on

rear of unit

power cord on

rear of unit2

centerline

height for

rear vent

39"

(99cm)

19.0"

(48cm)

* To obtain these minimal depth dimensions, dryer must be vented straight back. Using a quick-turn 90° elbow (right) adds approximately 0.75 in. (2 cm) to installation depth. Upward venting of exhaust on stacked

dryer adds approximately 4 in. (t0.2 cm) to installation depth. Downward venting of exhaust on stacked dryer adds approximately 2.25 in. (6.5 cm) to installation depth. Leftward venting of exhaust on stacked dryer

adds approximately 3.75 in. (9.5 cm) to installation depth.

1Hot and cold inlet hose length approximately 43 inches (t09cm)

2Powersupply cord length approximately 60 inches (t52.5cm).

3Drain hose length approximately 52 inches (t32cm).

Electrical installation

The following are specific requirements for proper and

safe electrical installation of your dryer. Failure to follow

these instructions can create electrical shock and/or a fire

hazard.

ELECTRICAL SHOCK HAZARD

* This appliance MUST be properly grounded.

Electrical shock can result if the dryer is not properly

grounded. Follow the instructions in this manual for

proper grounding.

* Do not use an extension cord with this dryer. Some

extension cords are not designed to withstand the

amounts of electrical current this dryer utilizes

and can melt, creating electrical shock and/

or fire hazard. Locate the dryer within reach of

the receptacle for the length power cord to be

purchased, allowing some slack in the cord. Refer to

the pre-installation requirements in this manual for

the proper power cord to be purchased.

ELECTRICAL SHOCK HAZARD

* A U.L.-approved strain relief must be installed onto

power cord. If the strain relief is not attached, the

cord can be pulled out of the dryer and can be cut

by any movement of the cord, resulting in electrical

shock.

Do not use an aluminum wired receptacle with a

copper wired power cord and plug (or vice versa).

A chemical reaction occurs between copper and

aluminum and can cause electrical shorts. The

proper wiring and receptacle is a copper wired

power cord with a copper wired receptacle.

Dryers operating on 208 volt power supply will have

longer drying times than dryers operating on 240 volt

Grounding requirements =Electric dryer (USA)

ELECTRICAL SHOCK HAZARD

Improper connection of the equipment grounding

conductor can result in a risk of electrical shock. Check

with a licensed electrician if you are in doubt as to

whether the appliance is properly grounded.

ii

For a grounded, cord-connected dryer:

1 The dryer MUST be grounded. In the event of a

malfunction or breakdown, grounding will reduce

the risk of electrical shock by a path of least

resistance for electrical current.

2 After you purchase and install a 3 wire or 4 wire

power supply cord having an equipment-grounding

conductor and a grounding plug that matches you

3

For a

1

wiring system, the plug MUST be plugged into

an appropriate, copper wired receptacle that is

properly installed and grounded in accordance with

all local codes and ordinances. If in doubt, call a

licensed electrician.

DO NOT modify the plug you've installed on this

appliance. If it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

permanently connected dryer:

The dryer MUST be connected to a grounded

metal, permanent wiring system; or an equipment

grounding conductor must be run with the circuit

conductors and connected to the equipment-

grounding terminal or lead on the appliance.

Grounding requirements = Electric dryer (Canada)

ELECTRICAL SHOCK HAZARD

Improper connection of the equipment grounding

conductor can result in a risk of electrical shock. Check

with a licensed electrician if you are in doubt as to

whether the appliance is properly grounded.

For a grounded, cord-connected dryer:

1 The dryer MUST be grounded. In the event of a

malfunction or breakdown, grounding will reduce

the risk of electrical shock by a path of least

resistance for electrical current.

2 Since your dryer is equipped with a power supply

cord having an equipment-grounding conductor

and a grounding plug, the plug must be plugged

into an appropriate outlet that is properly installed

and grounded in accordance with all local codes

and ordinances. If in doubt, call a licensed

electrician.

3 DO NOT modify the plug provided with this

appliance. If it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

Grounding requirements - Gas dryer (USA and Canada)

1 The dryer is equipped with a three-prong

(grounding) plug for your protection against shock

hazard and should be plugged directly into a

properly grounded three-prong receptacle.

2 The plug must be plugged into an appropriate

outlet that is properly installed and grounded in

accordance with all local codes and ordinances. If

in doubt, call a licensed electrician.

3 DO NOT modify the plug provided with this

appliance. If it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

Grounding type

wall receptacle

f

Do not, under

/ any circumstances,

cut, remove,

or bypass the

grounding prong.

Gas connection

1 Remove the shipping cap from gas pipe at the rear

of the dryer,

DO NOT connect the dryer to LP. gas service without

converting the gas valve. An L.P. conversion kit must be

installed by a qualified gas technician.

Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or

approved pipe from gas supply line to the 3/8 inch

(0.96 cm) pipe located on the back of the dryer.

Use a 1/2 inch to 3/8 inch (1.27 cm to 0.96 cm)

reducer for the connection. Apply an approved

thread sealer that is resistant to the corrosive

action of liquefied gases on all pipe connections.

Manual GASFLOW

Shutoff Flare _ Flare

Valve Union Union

:losea__ t ...... t t

Nipple Flexible Inlet Pipe on

Open Connector Back of Dryer

All connections must be wrench-tightened

The supply line must be equipped with an approved

manual shutoff valve. This valve should be located in

the same room as the dryer and should be in a location

that allows ease of opening and closing, Do not block

access to the gas shutoff valve- ..........................................................................................................................................................

3

4

Open the shutoff valve in the gas supply line to

allow gas to flow through the pipe. Wait a few

minutes for gas to move through the gas line.

Shutoff Valve-

Open position

Check for gas system leaks with a manometer. If a

manometer is not available, test all connections by

brushing on a soapy water solution.

EXPLOSION HAZARD

NEVER test for gas leaks with an open flame.

ii

Electrical connection (non=Canada) - 3 wire cord

3=wire receptacle

(NEMA type 10-30R)

ELECTRICAL SHOCK HAZARD

Failure to disconnect power source before servicing

could result in personal injury or even death.

1 Turn off power supply to outlet.

2 Remove the screw securing the terminal block

access cover in the lower corner on the back of the

dryer.

3 Install a UL-approved strain relief according to the

power cord/strain relief manufacturer's instructions

in the power cord entry hole below the access

panel. At this time, the strain relief should be

loosely in place.

4 Thread an UNPLUGGED, UL-approved, 30 amp.

power cord, NEMA 10-30 type SRDT, through the

strain relief.

5 Attach the power cord neutral (center wire)

conductor to the SILVER colored center terminal on

the terminal block. Tighten the screw securely.

6 Attach the remaining two power cord outer

conductors to the outer, BRASScolored terminals

on the terminal block. Tighten both screws

securely.

_ _ Access cover

_jj screw

Line 2

__z'-L_- _ (BRASSterminal)

Line 1

..... (BRASSterminal)

_ internal ground

(GREEN screw)

Terminal screw

recovery slot

ELECTRICAL SHOCK HAZARD

Do not make a sharp bend or crimp wiring/conductor at

connections,

7 Follow manufacturer's guidelines for firmly securing

the strain relief and power cord.

8 Reinstall the terminal block cover.

the access panel.

iii

DO NOTremove

Neutral

internal ground in

terminal

a 3-wire system!!

If moving dryer from a 4-wire system and installing it

in a 3-wire system, move the internal ground from the

center terminal back to the GREEN screw next to the

terminal block.

Electrical connection (non=Canada) - 4 wire cord

4-wire receptacle

(NEMA type 14-30R)

Neutral

WHITE wire)

ELECTRICAL SHOCK HAZARD

Failureto disconnect power source before servicing

could result in personal injury or even death.

1 Turn off power supply to outlet.

2 Remove the screw securing the terminal block

access cover in the lower corner on the back of the

dryer.

3 Install a UL-approved strain relief according to the

power cord/strain relief manufacturer's instructions

in the power cord entry hole below the access

panel. At this time, the strain relief should be

loosely in place.

4 Thread an UNPLUGGED, UL-approved, 30 amp.

power cord, NEMA 14-30 type ST or SRDT, through

the strain relief.

5 Disconnect the internal (BLACK) dryer harness

ground wire from the (GREEN) ground screw next

to the terminal block.

6 Attach the ground (GREEN) power cord wire to the

cabinet with the ground (GREEN) screw. Tighten

the screw securely.

7 Move the internal dryer harness ground (BLACK)

wire to the terminal block and attach it along with

the neutral (WHITE) power cord wire conductor

to the center, SILVER colored terminal on the

terminal block. Tighten the screw securely.

8 Attach the RED and BLACK power cord conductors

to the outer, BRASScolored terminals on the

terminal block. Tighten both screws securely.

ELECTRICAL SHOCK HAZARD

Do not make a sharp bend or crimp wiring/conductor at

connections,

9 Follow manufacturer's guidelines for firmly securing

the strain relief and power cord.

10 Reinstall the terminal block cover.

........... _ Install

UL-approved

strain relief here

Terminal screw

recovery slot

If a terminal screw falls during cord installation, it can

be retrieved in the terminal screw recovery slot below

Move internal ground (WHITE)

wire to neutral (SILVER)

terminal for 4-wire system.

GREEN

ground screw

Neutral

terminal

WHITE

neutral wire

GREEN

ground wir_

BLACKor

REDpower wire

BLACK

or RED

power wire

General installation

1 Connect the exhaust duct to the outside exhaust

system (see pages 6 through 8). Use of a 4" (102

mm) clamp (item A) is recommended to connect

the dryer to the exhaust vent system. Use metal

foil tape to seal all other joints.

2 Carefully slide the dryer to its final position. Adjust

one or more of the legs until the dryer is resting

solidly on all four legs. Place a level on top of the

dryer. The dryer MUST be level and resting solidly

on all four legs. Rock alternating corners to check

for stability, Remove and discard door tape,

Be sure the power is off at a circuit breaker/fuse box

before plugging the power cord into an outlet,

3 Plug the power cord into a grounded outlet,

4 Turn on the power at the circuit breaker/fuse box.

5 Read the Use & Care Guide provided with the dryer.

It contains valuable and helpful information that

will save you time and money.

6 If you have any questions during initial operation,

please review the "Avoid Service Checklist" in your

Use & Care Guide before calling for service.

7 Place these instructions in a location near the dryer

for future reference.

A wiring diagram and technical data sheet are located

inside the dryer console.

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

Removing the door

1 Protect fiat work surface, such as top of dryer or

floor near dryer, with a soft cloth or towel.

2 Open dryer door and remove the two hinge screws.

Remove lower screw first, then upper screw.

Supporting door with both hands, squarely lift door

and hinge upward approximately 3/8" (10 mm) so

"T" post on back of hinge can slide out through "T"

slot on front panel.

"T" SLOT IN

FRONT PANEL

"T" POST ON

DOOR HINGE

4

5

Gently place dryer door face down on fiat, covered

work surface.

Locate the 5 indented head screws (no. 1-5) in

the small, circular recesses (at 11, 1, 4, 6, and 8

o'clock positions) of the inner door. Remove and

save these 5 screws.

2

7

5 4

Do not attempt to remove the 2 "tamper-resistant"

screws that hold the inner glass !n place:....................................................................

6 Locate the 2 pan head screws (no. 6=7) on the

inner door nearest the metal strike and center of

hinge (9 and 3 o'clock positions). Remove and save

these 2 screws.

7 Separate inner door assembly from outer door

assembly.

Reversing the hinge

1

Carefully pull out the 2 small round hole plugs from

the front panel and save, Remove and save the

square "T" slot cover by sliding it up and pulling

it out. Move all 3 plugs to the opposite side of the

front panel and insert.

\

ROUND PLUG

ROUND PLUG_

1

2 Turn tuner door assembly over to expose retaining

tabs of metal strike. Grip tabs fully with pliers to

remove. Discard old metal strike.

3

Turn the inner door assembly back over and locate

the 2 pan head hinge screws. Remove and save the

2 screws and separate the hinge from inner door

assembly.

HINGE SCREWS

4

IN

From the back side of the inner door, pinch the

retaining tabs of the plastic square plug to release

it. Save square plug for reinstallation.

Carefully remove the 2 round plugs from the inner

door and move them to the opposite holes and

reinstall.

OUT

Rotate the hinge and move it to the opposite side

of the inner door. Attach it with the 2 pan head

screws removed previously. Reinstall plastic plug in

the square hole next to the hinge.

Reassembling the door

:[ Lift the inner glass ring. Rotate it 180 degrees,

reinstall on outer door, lining up indicators - "LH"

for left-hand hinge or "RH" for right-hand hinge.

a

b

2 Rest the opening of the inner door at a 90 degree

angle on the supports for the hinge cutout cover.

Pivot the inner door down onto the outer door.

3 Replace indented head screws (no. 1-5) removed

earlier. Take care not to strip out the plastic holes.

4 Replace pan head screws (no. 6-7) removed earlier.

Take care not to strip out the plastic holes.

2

5

Locate new metal strike supplied with dryer

manuals. Grip new strike with pliers as shown

below. Firmly insert the strike so it is oriented

vertically.

La page est en cours de chargement...

Frigidaire FASG7073LA0 Guide d'installation

Frigidaire FASG7073LA0 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents