Whirlpool WED8000DW Mode d'emploi

Marque: Whirlpool

Modèle: WED8000DW

Catégorie: Sèche-linge

Taper: Mode d'emploi

W10680139C

W10680140C - SP

If you have any problems or questions, visit us at www.whirlpool.com

Pour tout problème ou question, consulter www.whirlpoolappliances.ca

Use & Care Guide

Guide d’utilisation et d’entretien

Electronic Dryer

Sécheuse électronique

Para obtener acceso

al Manual de uso y

cuidado en español, o para

obtener información adicional

acerca de su producto, visite:

www.whirlpool.com.

Dryer Safety

Table of Contents

DRYER SAFETY .......................................................................2

CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW ...........4

CONTROL PANEL AND FEATURES ........................................5

CYCLE GUIDE .......................................................................... 6

USING YOUR DRYER ............................................................10

ADDITIONAL FEATURES .......................................................12

DRYER CARE .........................................................................13

TROUBLESHOOTING ............................................................15

WARRANTY ............................................................................18

ASSISTANCE OR SERVICE .................................... Back Cover

Table de matières

SÉCURITÉ DE LA SÉCHEUSE ...............................................19

VÉRIFICATION D’UNE CIRCULATION D’AIR ADÉQUATE

POUR LE SYSTÈME D’ÉVACUATION....................................21

TABLEAU DE COMMANDE ET CARACTÉRISTIQUES ..........23

GUIDE DES PROGRAMMES ..................................................25

UTILISATION DE LA SÉCHEUSE ........................................... 29

CARACTÉRISTIQUES SUPPLÉMENTAIRES .........................31

ENTRETIEN DE LA SÉCHEUSE .............................................32

DÉPANNAGE ..........................................................................34

GARANTIE .............................................................................. 38

ASSISTANCE OU SERVICE ..........................Couverture arrière

IMPORTANT: When discarding or storing your old clothes dryer, remove the door.

Check Your Vent System For Good Air Flow

Good air ow

Maintain good air ow by:

Cleaning your lint screen before each load.

Replace plastic or foil vent material

with 4" (102 mm) diameter heavy, rigid

vent material.

Good

Better

Use the shortest length of vent possible.

Use no more than four 90° elbows in a vent system;

each bend and curve reduces air ow.

Remove lint and debris from the exhaust hood.

Remove lint from the entire length of the vent system

at least every 2 years. When cleaning is complete, be

sure to follow the Installation Instructions supplied with

your dryer for nal product check.

Clear away items from the front of the dryer.

What To Dry and How To Dry? for better fabric care and energy savings.

By answering these questions, you can achieve the most energy savings and enhanced fabric care from your dryer. Using these

automatic cycles, the drying air temperature and moisture levels are sensed in the load. This sensing process occurs throughout

the entire drying cycle and turns off once the load reaches your selected dryness level. Using the NORMAL dryness level provides

the optimal energy savings.

If Timed Dry is your answer, the dryer runs for the amount of time you select, which sometimes results in shrinkage, wrinkling, and

static due to over-drying. Use Timed Dry for the occasional damp load that needs a little more drying time or when using the drying

rack.

Tips for getting the best performance from your steam dryer (on some models)

Results may vary depending on fabric. 100% cotton

garments with wrinkle-free nish may yield better results

than those without. 100% cotton items may require

additional touching up after cycles that use steam.

Use of fabric softener sheet is not recommended with

cycles that use steam. It may cause temporary staining

on clothes.

Cycles that use steam are not recommended for items that

have been starched. Wash any starched or new garments

prior to using a cycle that uses steam.

The Steam Refresh Cycle is best for smoothing out wrinkles

and reducing odors from loads consisting of dry items of

wrinkle-free cotton, cotton-polyester blend, common knits,

and synthetics.

Along with heat, dryers require good air ow to efciently

dry laundry. Proper venting will reduce your drying times and

improve your energy savings. See Installation Instructions.

The venting system attached to the dryer plays a big

role in good air ow. Blocked or crushed vents as well

as improper venting installation will reduce air ow and

dryer performance.

Service calls caused by improper venting are not covered by

the warranty and will be paid by the customer, regardless of

who installed the dryer. To clean or repair venting, contact a

venting specialist.

EcoBoost™ option

Touch to activate the EcoBoost™ option, which allows you to increase your energy savings by using a slightly lower heat level.

For automatic cycles the EcoBoost™ option will increase drying times by approximately 40 minutes; the LED Display will reect

this time.

The EcoBoost™ option will default on for Normal. For optimal energy turn on the EcoBoost™ option. For optimal time turn off

the EcoBoost™ option

Control Panel and Features

POWER

Touch to turn the dryer on and off. Touch to stop/cancel

a cycle at any time.

WHAT TO DRY/HOW TO DRY

First select a cycle from the “What to Dry” (Automatic

cycles) and then select the “How to Dry” to get the best

combination cycle available for the type of items you are

going to dry. See “Cycle Guide” for cycle details.

START/PAUSE

Touch and hold until the LED comes on to start a cycle,

or touch once while a cycle is in process to pause it.

LED DISPLAY

When you select a cycle, its default settings will light up

and the Estimated Time Remaining (for Automatic Cycles)

will vary depending on “What to Dry” and “How to Dry”

selections or actual time remaining for Timed Dry cycles

(for Manual Cycles) will be displayed.

Not all features and cycles are available on all models.

MODIFIERS

Use to select available modiers for your dryer. Not all

cycles and options are available on all models.

Temperature

When using Timed Dry Cycle, you may select a dry

temperature based on the type of load you are drying.

Use the warmest setting safe for the garments in the

load. Follow garment label instructions.

NOTE: Automatic Cycles will give you up to

3 temperatures to adjust and it varies, depending

on the “What to Dry” or “How to Dry” selections that

have been made.

Dryness

You may adjust the Dryness on Automatic Cycles

(except for the Sanitize cycle), if desired.

NOTE: Dryness is for use with Automatic Cycles only.

+\- Timed Dry Adjust

Touch “+” or “–” with Timed Dry cycle to increase or

decrease the length of the cycle.

NOTE: The control panel features a sensitive surface that responds to a light touch of your nger.

To ensure your selections are registered, touch the control panel with your nger tip, not your

ngernail. When selecting a setting or option, simply touch its name.

6 5

STEAM MODELS

NON-STEAM MODELS

OPTIONS

Use to select available options for your dryer. Not all

cycles and options are available on all models.

Static Reduce (on some models)

Touch to add the Static Reduce option to selected

Automatic cycles. The dryer will automatically tumble,

pause, and introduce a small amount of moisture

into the load to help reduce static. This option adds

approximately 8 minutes to the total cycle time.

End Beep

Use this to turn the signal indicating the end

of a drying cycle to low, medium, high, or off.

NOTE: You may also turn off the tones that sound

when a feature, setting, or option is touched. Touch

and hold End Beep for about three seconds to turn

sounds to low, medium, high, or off.

Damp Beep

Touch to select the Damp Beep signal. You may

adjust the signal to low, medium, high, or off. When

selected, a series of beeps will sound when the load

is damp, but not completely dry. This will allow you to

take clothes out of the load that do not need to dry

completely. This option is available on some cycles.

The Damp Beep signal is selected as a default for

the Bulky/Sheets cycle, as a reminder to manually

reposition bulky loads midway through the cycle.

Wrinkle Shield

™

Option

If you will be unable to remove a load immediately,

touch Wrinkle Shield

™

to add up to 150 minutes of

periodic tumbling to help reduce wrinkling. You may

select the “+ Steam” setting (on some models) to add

a short steam cycle after 60 minutes to help smooth

out wrinkles.

NOTE: If you open the dryer door prior to the end

of the Wrinkle Shield™ option, the dryer will go into

Pause mode. You will need to touch Power to turn

off or touch Start/Pause to continue Wrinkle Shield™

option.

EcoBoost

™

Option

Touch to activate the EcoBoost

™

option, which

allows you to increase your energy savings by using

a slightly lower heat level. This will increase dry

times. EcoBoost™ option will default on for Mixed

Normal. Can be selected for: Mixed Gentle, Casual

Normal, Casual Gentle, Delicate Normal, and Delicate

Gentle. It will be not available for the other cycles.

Steam Refresh (steam models only)

This cycle is best for reducing wrinkles and odors

from dry items. Cycle time will increase depending

on number of items.

Cycle Guide - Steam Model

How do you want to dry?

“How to Dry” Cycle Selection

Normal Sanitize* Gentle

Steam

Refresh

Timed

Dry

Regular

Automatic

Sensor Cycle

stops when

dryness level

is reached.

Hot High Heat

Used to kill

99.9% of

3 common

bacteria.

Lower Heat

Automatic

Sensor Cycle

stops when

dryness level is

reached.

Steam Cycle to

remove wrinkles

and odors.

Set amount of

dry time

Dryer runs for

the amount of

time selected.

What do you

want to dry?

“What to Dry”

Cycle Selection

Baby Clothes

Mixed

Handkerchiefs

a R

Pajamas

Sweatshirts

T-Shirts

Business Casual

Casuals

Cotton Drapes

Dress Shirts/Pants

Machine Wash Curtains

Napkins

No-Iron Fabrics

Tablecloth

The Whirlpool

Cabrio

dryer, has a unique user interface to help you select the best cycle you need for your load. The “What to Dry”

“How to Dry” layout guides you to the optimal cycle in two easy steps:

First determine what items are in the load that you are trying to dry. Use that to guide your “What to Dry” selection. Then determine

how you want the dryer to dry them by selecting the appropriate “How to Dry” selection.

To get the most energy savings and enhanced fabric care from your dryer use the Automatic cycles. These cycles measure the drying

air temperature and moisture levels to turn the dryer off once the load reaches the selected dryness level. Dryer performance and

results may vary with service voltage less than 240.

For best fabric care, choose the cycle that

best ts the load being dried.

R - Recommended Cycle

a - Alternate Cycle

Blank – Cycle is available but not optimal.

How do you want to dry?

“How to Dry” Cycle Selection

Normal Sanitize* Gentle

Steam

Refresh

Timed

Dry

Regular

Automatic

Sensor Cycle

stops when

dryness level

is reached.

Hot High Heat

Used to kill

99.9% of

3 common

bacteria.

Lower Heat

Automatic

Sensor Cycle

stops when

dryness level is

reached.

Steam Cycle to

remove wrinkles

and odors.

Set amount of

dry time

Dryer runs for

the amount of

time selected.

What do you

want to dry?

“What to Dry”

Cycle Selection

Dish Cloths

Towels

R a

Jeans

a R

Non-Rubber Lined Rugs

& Mats

Towels

Athletic/High

Performance Wear

Delicates

Bras

a R

Fabric Shower Curtain

Lingerie

a R

Sheers

Undergarments

a R

Wool

Blankets

Bulky/Sheets

Coats & Jackets

Comforters

Fabric Rugs

Fiber Fill Pillows (not

feather or decorative)

Heavy Drapes

Pet Bedding

Sheets

Sleeping Bags

Stuffed Animals

Feather Pillows

Air Only

Plastic Shower Curtains

Rubber and Rubber

backed rugs and mats

Vinyl Table Cloths

For best fabric care, choose the cycle that

best ts the load being dried.

R - Recommended Cycle

a - Alternate Cycle

Blank – Cycle is available but not optimal.

*Extended high-heat drying cycle intended to help sanitize items such as sheets and towels. This cycle is not recommended for all

fabrics. For best results, this cycle should be run to completion to ensure sanitization and do not interrupt cycle.

Cycle Guide - Non-Steam Model

The Whirlpool

Cabrio

dryer, has a unique user interface to help you select the best cycle you need for your load. The “What to Dry”

“How to Dry” layout guides you to the optimal cycle in two easy steps:

First determine what items are in the load that you are trying to dry. Use that to guide your “What to Dry” selection. Then determine

how you want the dryer to dry them by selecting the appropriate “How to Dry” selection.

To get the most energy savings and enhanced fabric care from your dryer use the Automatic cycles. These cycles measure the drying

air temperature and moisture levels to turn the dryer off once the load reaches the selected dryness level. Dryer performance and

results may vary with service voltage less than 240.

How do you want to dry?

“How to Dry” Cycle Selection

Normal Sanitize* Gentle

Heavy

Duty

Timed

Dry

Regular

Automatic

Sensor Cycle

stops when

dryness level is

reached.

Hot High Heat.

Used to kill

99.9% of

3 common

bacteria.

Lower Heat.

Automatic

Sensor Cycle

stops when

dryness level is

reached.

High Heat longer

cycle.

Automatic

Sensor Cycle

stops when

dryness level

is reached.

Set amount of

dry time

Dryer runs for

the amount of

time selected.

What do you

want to dry?

“What to Dry”

Cycle Selection

Baby Clothes

Mixed

Handkerchiefs

a R a

Pajamas

Towels-Normal

T-Shirts

Business Casual

Casuals

Cotton Drapes

Dress Shirts/Pants

Machine Wash Curtains

Napkins

No-Iron Fabrics

Tablecloth

Dish Cloths

Towels

a a R

Jeans

Non-Rubber Lined Rugs

& Mats

Sweatshirts

Towels

a R

Athletic/High

Performance Wear

Delicates

Bras

Fabric Shower Curtain

Lingerie

Sheers

Undergarments

a R

Wool

For best fabric care, choose the cycle that

best ts the load being dried.

R - Recommended Cycle

a - Alternate Cycle

Blank – Cycle is available but not optimal.

How do you want to dry?

“How to Dry” Cycle Selection

Normal Sanitize* Gentle

Heavy

Duty

Timed

Dry

Regular

Automatic

Sensor Cycle

stops when

dryness level is

reached.

Hot High Heat.

Used to kill

99.9% of

3 common

bacteria.

Lower Heat.

Automatic

Sensor Cycle

stops when

dryness level is

reached.

High Heat longer

cycle.

Automatic

Sensor Cycle

stops when

dryness level

is reached.

Set amount of

dry time

Dryer runs for

the amount of

time selected.

What do you

want to dry?

“What to Dry”

Cycle Selection

Blankets

Bulky/Sheets

Coats & Jackets

Comforters

Fabric Rugs

Heavy Drapes

Pet Bedding

Pillows - Fiber Fill

Sheets

Sleeping Bags

Stuffed Animals

Feather Pillows

Air Only

Plastic Shower Curtains

Rubber and Rubber

backed rugs and mats

Vinyl Table Cloths

For best fabric care, choose the cycle that

best ts the load being dried.

R - Recommended Cycle

a - Alternate Cycle

Blank – Cycle is available but not optimal.

*Extended high-heat drying cycle intended to help sanitize items such as sheets and towels. This cycle is not recommended for all

fabrics. For best results, this cycle should be run to completion to ensure sanitization and do not interrupt cycle.

Touch POWER

Touch POWER to turn on the dryer.

Using Your Dryer

Clean the lint screen

Clean the lint screen before each load. Pull the lint screen

straight up and push tab down on front to open lint screen.

Roll lint off the screen with your ngers. Do not rinse or wash

screen to remove lint. Wet lint is hard to remove. Close lint

screen and push the lint screen rmly back into place.

For additional cleaning information, see “Dryer Care.”

Load the dryer

Open the door by pulling on the handle. Place laundry in the

dryer. Add a dryer sheet to wet load, if desired. Close the door.

IMPORTANT: Do not tightly pack the dryer. Items need

to tumble freely. Tightly packing can lead to poor drying

performance and may increase wrinkling and tangling.

WARNING: To reduce the risk of re, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance.

Select type of load to dry

First select a cycle from the “What to Dry” (Automatic cycles)

and then select the “How to Dry” to get the best combination

cycle available for the type of items you are going to dry. See

“Cycle Guide” for cycle details. Not all cycles are available on

all models.

Automatic Cycles:

You can select a different dryness level, depending on your

load. Touch DRYNESS to scroll to Less to More. Selecting

Less to More automatically adjusts the dryness level at which

the dryer will shut off. Dryness level can be changed in the rst

5-8 minutes of the cycle.

Automatic Cycles give the best drying in the shortest time.

Drying time varies based on fabric type, load size, and

dryness setting.

NOTE: Automatic Cycles will give you up to 3 temperatures to

adjust and it varies, depending on the “What to Dry” or “How

to Dry” selections that have been made.

TIMED DRY Cycle:

When you select Timed Dry, the default time appears in the

display. Touch “+” and “–” to increase or decrease the time in

1 minute increments. Touch and hold to change the time in 5

minute increments.

The default temperature may be changed by pressing

Temperature until the desired dry temperature is lit.

Steam Refresh Cycles (on some models):

Select Steam Refresh to reduce odors and light wrinkles in

dry loads consisting of wrinkle-free cotton, cotton-polyester

blends, common knits, and synthetics. If you will be unable

to remove a load immediately, touch Wrinkle Shield

™

to add

up to 150 minutes of periodic tumbling. You may select the +

Steam setting to add a short steam cycle after 60 minutes to

help smooth out wrinkles.

Touch and hold START/PAUSE

to begin cycle

Touch and hold START/PAUSE to begin the cycle.

8. Remove garments promptly

after cycle is nished

Promptly remove garments after cycle has completed

to reduce wrinkling.

Adjust cycle modiers, if desired

You may adjust different settings,

depending on what you are drying and

how your are going to dry the item. See the

“Cycle Guide” for detailed information.

NOTE: Not all options and modiers are

available with all cycles. Not all cycles

are on all models.

Select any additional options

Add additional options such as Static Reduce, Wrinkle Shield,

and/or EcoBoost

™

(on some models) by touching that option.

If you will be unable to remove the load promptly, select

Wrinkle Shield

™

before pressing START/PAUSE. You may

select the “+ Steam” setting (on some models) to add a short

steam cycle after 60 minutes to help smooth out wrinkles.

NOTE: Not all options and settings are available with all

cycles.

Changing the Automatic Cycle settings

to increase or decrease drying time

If all your loads on all Automatic Cycles are consistently less

dry or more dry than you would like, you may change the

default settings to increase or decrease the default dryness

level.

Your automatic drying settings can be adjusted to adapt to

different installations, environmental conditions, or personal

preference. This change is retained and will affect all of your

Automatic Cycles, not just the current cycle/load. There are

5 drying settings, which are displayed using the time display:

0 Much wetter clothes, 30% less drying time.

1 Slightly wetter clothes, 15% less drying time.

2 Factory preset dryness level.

3 Slightly drier clothes, 15% more drying time.

4 Much drier clothes, 30% more drying time.

To change the drying settings:

NOTE: The settings cannot be changed while the dryer

is running or paused. The dryer must be in standby mode

(power is off) to adjust the default settings.

1. Before starting a cycle, touch and hold DRYNESS

for 6 seconds.

2. Touch DRYNESS to select the dryness level shown in

the time display: 0, 1, 2, 3, or 4.

3. Touch START/PAUSE to save the new dryness level

setting.

Additional Features

USING THE DRYING RACK

To obtain a drying rack for your dryer, order by calling

1-877-944-7566. You will need your model and serial

number and the purchase date. Remove and discard any

packing material before use.

Use the Drying Rack for items that you do not want to

tumble dry, such as sweaters and tennis shoes. When you

use the drying rack, the drum continues to turn, but the

rack remains stationary.

The drying rack is intended for use with the Manual Dry/

Timed Dry cycles only. The drying rack cannot be used

with Automatic cycles.

To use the drying rack:

IMPORTANT: Do not remove the lint screen.

1. Open dryer door.

USING THE DRYING RACK (cont.)

2. Align the two hooks on the front of the drying rack with

the holes in the dryer door opening and press down

fully into holes. Rest the rear support on the dryer back

ledge.

3. Place wet items on top of the drying rack. Allow space

around items for air to circulate. The drying rack does

not move, but the drum will rotate; be sure to leave

adequate clearance between items and the inside of

the dryer drum. Make sure items do not hang over the

edges or between drying rack grille.

4. Close the door.

5. Select a Timed Dry/Air Only, or Low Temperature cycle.

Items containing foam, rubber, or plastic must be dried

on a clothesline or by using the Air Only setting.

6. When the cycle is selected, the Estimated Time

Remaining display shows the default time. You can

change the actual time in the cycle by increasing or

decreasing the cycle time.

7. Start the dryer.

NOTE: Check the lint screen and remove any lint

accumulated from items dried on the drying rack after the

cycle is nished.

CLEANING THE LINT SCREEN

Every load cleaning

The lint screen is located in the door opening of the dryer.

The control panel has an indicator light “Check Lint” to

remind you to clean the lint screen after each load. A

screen blocked by lint can increase drying time.

To clean:

1. Pull the lint screen straight up. Press tab down and open

lint screen. Roll lint off the screen with your ngers. Do

not rinse or wash screen to remove lint. Wet lint is hard

to remove.

2. Close the lint screen and push rmly back into place.

IMPORTANT:

Do not run the dryer with the lint screen loose,

damaged, blocked, or missing. Doing so can cause

overheating and damage to both the dryer and fabrics.

If lint falls off the screen into the dryer during removal,

check the exhaust hood and remove the lint. See

“Venting Requirements” in the Installation Instructions.

Clean space where lint

screen is located, as

needed. Using a vacuum,

gently remove any lint that

has accumulated outside of

the lint screen.

As needed cleaning

Laundry detergent and fabric softener residue can build

up on the lint screen. This buildup can cause longer

drying times for your clothes, or cause the dryer to stop

before your load is completely dry. The screen is probably

clogged if lint falls off while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months,

or more frequently, if it becomes clogged due to a residue

buildup.

To wash:

1. Roll lint off the screen with your ngers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent.

Scrub lint screen with the brush to remove residue

buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel.

Reinstall screen in dryer.

Dryer Care

CLEANING THE DRYER LOCATION

Keep dryer area clear and free from items that would

block the air ow for proper dryer operation. This includes

clearing piles of laundry in front of the dryer.

CLEANING THE DRYER INTERIOR

To clean dryer drum

1. Use a mild hand dish detergent mixed at a low

concentration with very warm water, and rub with

a soft cloth.

2. Rinse well with a wet sponge or towel.

3. Tumble a load of clean clothes or towels to dry drum

Use a microber cloth and hot water in a spray bottle

to clean the drum and a second microber towel to dry.

NOTE: Garments that contain unstable dyes, such as

denim blue jeans or brightly colored cotton items, may

discolor the rear of the dryer interior. These stains are

not harmful to your dryer and will not stain future loads

of clothes. Dry unstable dye items inside out to avoid

transfer of dye.

REMOVING ACCUMULATED LINT

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often,

depending on dryer usage. Cleaning should be done by a

qualied appliance servicer or ventilation system cleaner.

From the Exhaust Vent

Lint should be removed every 2 years, or more often,

depending on dryer usage.

SPECIAL INSTRUCTIONS

FOR STEAM MODELS

Water Inlet Hose

Replace inlet hose and hose screen after 5 years of use

to reduce the risk of hose failure. Periodically inspect and

replace inlet hose if bulges, kinks, cuts, wear, or leaks

are found.

When replacing your inlet hose, record the date

of replacement.

To Winterize the Dryer

1. Unplug dryer or disconnect power.

2. Shut off water faucet.

3. Disconnect water inlet hose from faucet and drain.

To Use the Dryer Again

1. Flush water pipes. Reconnect water inlet hose to faucet.

Turn on water faucet.

2. Plug in dryer or reconnect power as described in the

Installation Instructions.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

NON-USE, STORAGE, AND MOVING CARE

Steam models only: Install and store your dryer where it

will not freeze. Because some water may stay in the hose,

freezing can damage your dryer. If storing or moving your

dryer during freezing weather, winterize it.

Non-Use or Storage Care

Operate your dryer only when you are at home. If you will

be on vacation or not using your dryer for an extended

period of time, you should:

1. Unplug dryer or disconnect power.

2. Clean lint screen. See “Cleaning the Lint Screen.”

3. Turn off the water supply to the dryer. This helps to

avoid unintended ooding (due to a water pressure

surge) while you are away.

Moving Care

For power supply cord-connected dryers:

1. Unplug the power supply cord.

2. Gas models only: Close shut-off valve in gas supply line.

3. Gas models only: Disconnect gas supply line pipe and

remove ttings attached to dryer pipe.

4. Gas models only: Cap the open fuel supply line.

5. Steam models only: Shut off water faucet.

6. Disconnect the water inlet hose from faucet, then drain

the hose. Transport hose separately.

7. Make sure leveling legs are secure in dryer base.

8. Use tape to secure dryer door.

For direct-wired dryers:

1. Disconnect power.

2. Disconnect wiring.

3. Steam models only: Shut off water faucet.

4. Steam models only: Disconnect the water inlet hose from

faucet; then drain the hose. Transport hose separately.

5. Make sure leveling legs are secure in dryer base.

6. Use tape to secure dryer door.

Reinstalling the Dryer

Follow the Installation Instructions to locate, level, and

connect the dryer.

Troubleshooting

If you experience Possible Causes Solution

Dryer Operation

Dryer will not run Door not closed completely. Make sure the dryer door is closed completely.

START/PAUSE touched with

ngernail.

Touch START/PAUSE with pad of nger.

Household fuse is blown or circuit

breaker has tripped.

There may be 2 household fuses or circuit breakers for the dryer.

Check that both fuses are intact and tight, or that both circuit

breakers have not tripped. Replace the fuses or reset the circuit

breaker. If the problem continues, call an electrician.

Incorrect power supply. Electric dryers require 240-volt power supply. Check with a

qualied electrician.

Wrong type of fuse. Use a time-delay fuse.

Dryer will not turn off Dryer door was opened prior to the

end of the Wrinkle Shield™ option.

If you open the dryer door prior to the end of the Wrinkle

Shield™ option, the dryer will go into Pause mode. You will

need to touch Power to turn off or touch Start/Pause to continue

Wrinkle Shield™ option.

Dryer will not heat Household fuse is blown or circuit

breaker has tripped.

The drum may be turning, but you may not have heat. Electric

dryers use 2 household fuses or circuit breakers. Replace the

fuses or reset the circuit breaker. If the problem continues, call

an electrician.

Incorrect power supply. Electric dryers require 240-volt power supply. Check with a

qualied electrician.

Supply line valve not open. For gas dryers, make sure that the valve on the gas supply line

is open.

Unusual Noise

Humming or whining

noise with Steam cycle

selected

Water pump on dryer is running. The water pump on the dryer is used during the Steam function.

If the dryer has just been installed or unused for an extended

period, the pump may be louder and run longer. This is normal.

Thumping noise Dryer hasn’t been used in a while. This is normal. The thumping sound should diminish after a few

minutes of use.

Rattling or vibrating noise A small object caught between the

edges of dryer drum.

Check the front and rear edges of the drum for small objects.

Clean out pockets before laundering.

Dryer isn’t properly leveled. The dryer may vibrate if not properly installed. See the

Installation Instructions. All four dryer feet should be in rm

contact with the oor.

Clothing is balled up in dryer. When balled up, the load will bounce, causing the dryer to

vibrate. Separate the load items and restart the dryer.

Clicking noise Gas valve operating. On gas dryers, you may hear the gas valve clicking as it opens

and closes. This is normal.

Dryer Results

Drying times are too

long and clothes are not

getting dry

Lint screen or lint screen housing is

clogged with lint.

Clean lint screen before each load. Clean space where lint

screen is located, as needed. Using a vacuum, gently remove

any lint that has accumulated outside of the lint screen.

The exhaust vent or outside exhaust

hood is clogged with lint, restricting

air movement.

Run the dryer for 5–10 minutes. Hold your hand under the

outside exhaust hood to check air movement. If you do not feel

air movement, clean exhaust system of lint or replace exhaust

vent with heavy metal or exible metal vent. See the Installation

Instructions.

The exhaust vent is not the correct

length.

Check that the exhaust vent is not too long or has too many

turns. Long venting will increase drying times. See the

Installation Instructions.

The exhaust vent diameter is not the

correct size.

Use 4" (102 mm) diameter vent material.

The dryer is not level. Clothes not contacting the moisture sensors during Automatic

cycles. See “Level Dryer” in the Installation Instructions.

The No Heat temperature setting has

been selected.

Select the correct temperature for the types of garments being

dried. See “Cycle Guide.”

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help –

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Troubleshooting

If you experience Possible Causes Solution

Dryer Results (cont.)

Drying times are too

long and clothes are not

getting dry

The load is too large and heavy to dry

quickly.

Separate the load to tumble freely.

Fabric softener sheets are blocking

the grille.

The air outlet grille is just inside the door, behind the lint screen.

Check that it is not blocked by a fabric softener sheet.

Use only one fabric softener sheet, and use it only once.

The dryer is located in a room with

temperature below 45ºF (7ºC).

Proper operation of dryer cycles requires temperatures above

45ºF (7ºC).

The dryer is located in a closet. Closet doors must have ventilation openings at the top and

bottom of the door. The front of the dryer requires a minimum of

1" (25 mm) of airspace, and, for most installations, the rear of the

dryer requires 5" (127 mm). See the Installation Instructions.

Cycle time is too short The load may not be contacting the

sensor strips on Automatic Cycles.

Level the dryer. See the Installation Instructions. All four dryer

feet should be in rm contact with the oor.

Clothes are coming out of the Steam

Refresh cycle with damp or wet

spots.

Under certain environmental or installation conditions, you may

experience underdrying.

The automatic cycle is ending early. Change the dryness level setting on Automatic Cycles.

Increasing or decreasing the dryness level will change the

amount of drying time in a cycle. If loads are consistently ending

too early, see also “Changing the Automatic Cycle settings to

increase or decrease drying time.”

Lint on load Lint screen is clogged with lint. Clean lint screen before each load.

Stains on load Improper use of fabric softener. Add dryer fabric softener sheets at the beginning of the cycle.

Fabric softener sheets added to a partially dried load can stain

your garments. Do not use fabric softener sheets with steam

cycles.

Stains on drum Loose dyes in clothes. Drum stains are caused by dyes in clothing (usually blue jeans).

These will not transfer to other clothing.

Loads are wrinkled The load was not removed from dryer

at the end of the cycle.

Select Steam Refresh cycle to tumble the load with water and

heat. This cycle is best for smoothing out wrinkles and reducing

odors from dry loads consisting of wrinkle-free cotton, cotton-

polyester blends, common knits, and synthetics.

NOTE: Refer to garment care label instructions. Dry-clean-only

garments are not recommended.

The dryer was tightly packed. Dry smaller loads that can tumble freely. Results may also vary

depending on fabric type.

For steam cycles, the water is not

properly connected with the dryer.

Make sure water is connected to the dryer. Check that water

inlet hose is connected to both the faucet and dryer’s water inlet

valve. Check that the water supply is turned on.

Odors Recent painting, staining, or

varnishing in the area where your

dryer is located.

Ventilate the area. When the odors or fumes are gone from the

area, rewash and dry the clothing.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Troubleshooting

If you experience Possible Causes Solution

Dryer Results (cont.)

Odors (cont.) For steam cycles, the water is not

properly connected with the dryer.

Make sure water is connected to the dryer. Check that water

inlet hose is connected to both the faucet and dryer’s water inlet

valve. Check that the water supply is turned on.

Odors are left in garments after

wearing.

To remove odors left in garments after wearing, select Steam

Refresh. This cycle is best for reducing wrinkles and odors from

dry loads consisting of wrinkle-free cotton, cotton-polyester

blends, common knits, and synthetics.

Load too hot Load removed before cooldown

portion of cycle complete.

Allow the dryer to complete the cooldown portion of the cycle

before removing the load.

Using Timed Dry cycle with a high

temperature setting.

Select an Automatic Cycle with a lower heat setting to avoid

overdrying the load.

Dryer Displaying Code Message or Indicator Is Lit

“PF” (power failure) The drying cycle has been interrupted

by a power failure.

Touch and hold START to restart the dryer cycle or press power

to clear the display.

“L2” Diagnostic Code

(low or no line voltage

condition)

There may be a problem with your

home power supply, keeping the

dryer’s heater from turning on.

The dryer will continue to run when this diagnostic code is

present. Touch any pad to clear the code from the display and

return to the estimated time remaining.

NOTE: This error will only show during the initial installation.

Try the following:

•

Check to see if a household fuse has blown or circuit breaker

has tripped. Electric dryers use two household fuses or

breakers. Replace the fuse or reset the circuit breaker.

•

Conrm that the power cord is properly installed. Refer to

the Installation Instructions for details.

•

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, consult a qualied electrician.

“F# E#” (F1 E1, F3 E1,

etc.) variable service

codes.

The dryer is in need of service. If a code beginning with an “F” appears in the display, alternating

between F# and E#, the dryer control has detected a problem

that requires service. Call for service.

AF (restricted air ow) The lint screen or vent is clogged;

the vent is crushed, kinked or has

too many turns.

The dryer will continue to run when this diagnostic code is

present. Touch any key to clear the code from the display and

return to the estimated time remaining.

Try the following:

•

Clean lint screen.

•

Check to see if the vent run from the dryer to the wall is

crushed or kinked.

•

Conrm that the vent run from the dryer to the wall is free

of lint and debris.

•

Conrm that the exterior vent exhaust hood is free of lint

and debris.

•

Conrm that your vent system falls within the recommended

run length and number of elbows for the type of vent you are

using. Refer to “Plan Vent System” in the Installaton Instructions

for details.

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, have your entire home venting run

cleaned. Contact a venting specialist.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

WHIRLPOOL

LAUNDRY

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS

REQUIRED TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

Name, address, and telephone number

Model number and serial number

A clear, detailed description of the problem

Proof of purchase including dealer or retailer name and address

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or tness, so this limitation may not apply to you. This

warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

03/14

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair.

Some questions can be addressed without service. Please take a few minutes to review the

Troubleshooting or Problem Solver section of the Use and Care Guide, scan the QR code on

the right to access additional resources, or visit https://www.whirlpool.com/product_help.

2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers.

In the U.S. and Canada, direct all requests for warranty service to:

Whirlpool Customer eXperience Center

In the U.S.A. call 1-800-253-1301. In Canada call 1-800-807-6777.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.

https://www.whirlpool.com/product_help

ONE YEAR LIMITED WARRANTY

WHAT IS COVERED

WHAT IS NOT COVERED

1. Commercial, non-residential, multiple-family use, or use inconsistent with published

user, operator, or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not in

accordance with electrical or plumbing codes, or correction of household electrical or

plumbing (i.e. house wiring, fuses, or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water ﬁlters, etc.).

5. Conversion of your product from natural gas or L.P. gas or reversal of appliance doors.

6. Damage from accident, misuse, abuse, ﬁre, ﬂoods, acts of God, or use with products

not approved by Whirlpool.

7. Repairs to parts or systems to correct product damage or defects caused by

unauthorized service, alteration, or modiﬁcation of the appliance.

8. Cosmetic damage including scratches, dents, chips, and other damage to appliance

ﬁnishes unless such damage results from defects in materials and workmanship and is

reported to Whirlpool within 30 days.

9. Discoloration, rust, or oxidation of surfaces resulting from caustic or corrosive

environments, including but not limited to, high salt concentrations, high moisture or

humidity, or exposure to chemicals.

10. Pick-up or delivery. This product is intended for in-home repair.

11. Travel or transportation expenses for service in remote locations where an authorized

Whirlpool servicer is not available.

12. Removal or reinstallation of inaccessible appliances or built-in ﬁxtures (i.e. trim,

decorative panels, ﬂooring, cabinetry, islands, countertops, drywall, etc.) that interfere

with servicing, removal, or replacement of the product.

13. Service or parts for appliances with original model/serial numbers removed, altered, or

not easily determined.

The cost of repair or replacement under these excluded circumstances shall be

borne by the customer.

For one year from the date of purchase,

when this major appliance is installed,

operated, and maintained according to

instructions attached to or furnished with

the product, Whirlpool Corporation or

Whirlpool Canada LP (hereafter “Whirlpool”)

will pay for Factory Specified Replacement

Parts and repair labor to correct defects

in materials or workmanship that existed

when this major appliance was purchased,

or at its sole discretion replace the product.

In the event of product replacement, your

appliance will be warranted by the remaining

term of the original unit’s warranty period.

YOUR SOLE AND EXCLUSIVE REMEDY

UNDER THIS LIMITED WARRANTY SHALL

BE PRODUCT REPAIR AS PROVIDED

HEREIN. Service must be provided by a

Whirlpool designated service company. This

limited warranty is valid only in the United

States or Canada and applies only when

the major appliance is used in the country

in which it was purchased. This limited

warranty is effective from the date of original

consumer purchase. Proof of original

purchase date is required to obtain service

under this limited warranty.

Sécurité de la sécheuse

IMPORTANT : Pour mettre l’ancienne sécheuse au rebut ou pour la remiser, enlever la porte.

La page charge ...

Whirlpool WED8000DW Mode d'emploi

Marque: Whirlpool

Modèle: WED8000DW

Catégorie: Sèche-linge

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WED8000DW User guide

Documents connexes

Autres documents

Frigidaire FASG7073LN Le manuel du propriétaire