Yes NK30CB700WCG Manuel utilisateur

Marque: Yes

Modèle: NK30CB700WCG

Catégorie: Hottes

Taper: Manuel utilisateur

Ce manuel convient également à

Range Hood

Installation & User Manual

NK30CB700W**/NK36CB700W**

2 English

Contents

Makeup Air 24

Using the lighting 24

Checking air quality 25

Filter cleaning reminder 25

Wi-Fi On/Off 26

Smart ventilation mode 26

Automatic operation to prevent range hood overheating 27

Language setting 28

Entering AP(Access Point) 28

Cleaning and Maintenance 29

AI Energy Mode 29

Bixby 29

Amazon Alexa & Google Assistant 29

Installation Guide 29

Cleaning the range hood 30

Cleaning the sensor unit 30

Cleaning the Filters 31

Replacing the LED Lamp 31

SmartThings app 31

Open Source Announcement 33

Troubleshooting 33

General 33

Hood Operation 33

Information codes 34

Warranty (USA) 35

Warranty (CANADA) 36

Contents

Important Safety Instructions 3

Installation Requirements 7

General Specifications 7

Mounting Height 7

Venting Methods 8

Parts List 8

Sub-Parts List 9

Additional Purchase Accessories 9

Installation Clearances 9

Making a hole in the furniture 10

Installation 11

Setting the Location 11

Connecting the Vent System 12

Installing the Range Hood 13

Connect the filter support cable 16

Installing the Recirculation Kit 16

Range Hood Description 20

Range Hood Overview 20

Button panel 20

Using the Range Hood 21

Display 21

Turning the Range Hood On or Off 21

First Use Guide 22

Changing the operation mode 22

Smart mode 23

Activates/Deactivates Boost mode 23

English 3English 3

Important Safety Instructions

APPROVED FOR RESIDENTIAL APPLIANCES FOR RESIDENTIAL USE ONLY

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ THE ENTIRE INSTALLATION GUIDE BEFORE PROCEEDING.

INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

IMPORTANT: Save these instructions for the local electrical inspector's use.

INSTALLER: Please leave these Instructions with this unit for the owner.

OWNER: Please retain these instructions for future reference.

Symbols used in this manual

WARNING

Hazards or unsafe practices that may result in severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in electric shock, personal injury, or

property damage.

NOTE

Useful tips and instructions

These warning icons and symbols are here to prevent injury to you and others.

Please follow them explicitly. After reading this section, keep it in a safe place for

future reference.

WARNING

Turn off the power circuit in the service panel and lock out panel before wiring this

appliance.

Installation requires a branch circuit of 120 VAC, 60 Hz, and 15 or 20 A.

State of California Proposition 65 warning (US only)

WARNING

This product contains chemicals known to the State of California to cause cancer

and birth defects or other reproductive harm.

1. FCC Notice

CAUTION

FCC CAUTION: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to operate the

equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that

causes undesired operation.

For products sold in the US and Canadian markets, only channels 1-11 are available.

You cannot select any other channels.

FCC STATEMENT:

This equipment has been tested and found to be in compliance within the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful

interference with radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorienting or relocating the receiving antenna

• Increasing the separation between the equipment and receiver

• Connecting the equipment to an outlet that is on a different circuit than the radio

or TV.

• Consulting with a dealer or an experienced radio/TV technician for help.

4 English

Important Safety Instructions

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING PRECAUTIONS:

• Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer.

• Before servicing or cleaning the unit, switch the power off at the service panel and

lock the service panel to prevent the power from being switched on accidentally.

If the service panel cannot be locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

• The installation work and electrical wiring must be done by qualified person(s)

in accordance with all applicable codes and standards, including fire-rated

construction.

• Sufficient air is needed for proper combustion and the exhausting of gases

through the flue (chimney) of the fuel burning equipment to prevent backdrafting.

Follow the heating equipment manufacturer’s guidelines and safety standards,

such as those published by the National Fire Protection Association (NFPA), the

American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

• When cutting or drilling into the wall or ceiling, do not damage electrical wiring or

other hidden utilities.

• Ducted fans must always be vented outdoors.

CAUTION

For general ventilating use only. Do not use to exhaust hazardous or explosive

materials and vapors.

CAUTION

To reduce the risk of fire and to properly exhaust air, be sure to duct air outside -

do not vent exhaust air into spaces enclosed within walls, ceilings, attics, or into

crawl spaces or garages.

FCC RADIATION EXPOSURE STATEMENT:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated so

there is at least 8 inches (20 cm) between the radiator and your body. This device

and its antenna(s) must not be co-located or operated in conjunction with any

other antenna or transmitter.

2. IC Notice

The term “IC” before the radio certification number only signifies that Industry

Canada technical specifications were met. Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause undesired operation

of the device.

This Class B digital apparatus complies with Canadian ICES-003. For products sold

in the US and Canadian markets, only channels 1-11 are available. You cannot

select any other channels.

IC RADIATION EXPOSURE STATEMENT:

This equipment complies with the IC RSS-102 radiation exposure limits set forth

for an uncontrolled environment. This equipment should be installed and operated

so there is at least 8 inches (20 cm) between the radiator and your body. This

device and its antenna(s) must not be co-located or operated in conjunction with

any other antenna or transmitter.

English 5English 5

Important Safety Instructions

WARNING

Do not let children near this appliance. Do not let children play with this appliance.

Keep all packaging materials out of children’s reach. Properly dispose the

packaging materials after this appliance is unpacked.

Electrical Requirements

IMPORTANT

Observe all governing codes and ordinances.

It is the customer’s responsibility:

To contact a qualified electrical installer.

To assure that the electrical installation is adequate and in conformance with the

National Electrical Code, ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-

94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all

local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a

qualified electrician determine that the ground path is adequate. A copy of the

above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

• If the house has aluminum wiring, follow the procedure below:

1. Connect a section of solid copper wire to the pigtail leads.

2. Connect the aluminum wiring to the added section of copper wire using

special connectors and/or tools designed and UL listed for joining copper to

aluminum.

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

• Never leave surface units unattended at high settings. Boilovers cause smoking

and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

• Always turn the hood ON when cooking at high heat or when flambeing food (i.e.

Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

• Clean ventilating fans frequently. Grease should not be allowed to accumulate on

the fan or filter.

• Use proper pan sizes. Always use cookware appropriate for the size of the surface

element.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP

GREASE FIRE, OBSERVE THE FOLLOWING PRECAUTIONS:*

• SMOTHER FLAMES with a close fitting lid, cookie sheet, or metal tray, then turn

off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out

immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

• NEVER PICK UP A FLAMING PAN - you may get burned.

• DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion

will result.

• Use an extinguisher ONLY if:

–You know you have a class ABC extinguisher, and you already know how to

operate it.

–The fire is small and contained in the area where it started.

–The fire department is being called.

–You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

WARNING

To reduce the risk of fire or electrical shock, do not use this fan with any solid-

state speed control device.

6 English

Important Safety Instructions

• Use clamps to seal all joints in the vent system.

• The vent system must have a damper.

• Use caulking to seal the exterior wall or roof opening around the cap.

• The size of the vent should be uniform.

Venting Methods

To use the hood’s top outlet to vent your hood, a 6” (15.2 cm) round vent system is

required. To use the hood’s rear outlet, a 31⁄4” x 10” (8.25 x 25.4 cm) rectangular

vent system is required. Neither of these vent systems are included and must be

purchased separately.

NOTE

Flexible vents are not recommended. Flexible vents create back pressure and air

turbulence that greatly reduces performance. The vent system can terminate either

through the roof or a wall. To vent through a wall, a 90° elbow is needed.

Mounting Height

Select a mounting height between a minimum of 24” (61 cm) for an electric

cooking surface, a minimum of 27” (68.6 cm) for a gas cooking surface, and a

suggested maximum of 36” (91.4 cm) above the range to the bottom of the hood.

Rear discharge

A 90° elbow may be installed immediately above the hood.

For Non-Vented (recirculating) Installations

If it is not possible to vent cooking fumes and vapors to the outside, the hood can

be used in the non-vented (recirculating) version, fitting a charcoal filter and a

plastic grid. Fumes and vapors are recycled through the recirculation grid.

• Follow the electrical connector manufacturer’s recommended procedure.

Aluminum/copper connections must conform with local codes and industry

accepted wiring practices.

• Wire sizes and connections must conform with the rating of the appliance as

specified on the model/serial rating plate. The model/serial plate is located behind

the filter on the rear wall of the range hood.

• Wire sizes must conform to the requirements of the National Electrical Code, ANSI/

NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 (latest edition and all local codes and ordinances.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit,

grounding reduces the risk of electric shock by providing an escape wire for the

electric current. This appliance is equipped with a cord that has a grounding wire

with a grounding plug. The plug must be plugged into an outlet that is properly

installed and grounded.

WARNING

• Improper grounding can result in a risk of electric shock.

• Consult a qualified electrician if the grounding instructions are not completely

understood, or if doubt exists as to whether the appliance is properly grounded.

• Do not use an extension cord. If the power supply cord is too short, have a

qualified electrician install an outlet near the appliance.

Venting Requirements (ducted models only)

• The vent system must terminate outdoors.

• Do not terminate the vent system in an attic or other enclosed area.

• Do not use a 4” (10.2 cm) laundry-type wall cap.

• Only use metal vents. Rigid metal vents are recommended. Plastic or metal foil

vents are not recommended.

• The length of the vent system and the number of elbows should be kept to a

minimum to provide efficient performance.

For the most efficient and quietest operation:

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24” (61 cm) of straight vent between the elbows

if more than one elbow is used.

• Do not install two elbows together.

English 7English 7

Installation Requirements

Mounting Height

CAUTION

• Be sure to check the mounting height before installing the product.

• The mounting height is measured from the top of the range to the upper

cabinets. The mounting height for an electric cooking surface is measured from

its glass cooktop as shown in the image on the left. For a gas cooking surface,

the mounting height is measured from the top of the burning grates as shown in

the image on the right.

Min 24 " (61 cm)

Max 36 " (91.4 cm)

Min 24" (61 cm)

Max 36" (91.4 cm)

Min 27 " (68.5 cm)

Max 36 " (91.4 cm)

Min 27" (68.5 cm)

Max 36" (91.4 cm)

ELECTRIC RANGES GAS RANGES

General Specifications

11 1/4" (28.5 cm) 13 11/16" (34.8 cm)

2 3/16" (5.5 cm)

19 11/16" (50.0 cm)

Vent Mode (Extension Kit)

Min 40" (101.6 cm)

Max 71

" (180.6 cm)

Vent Mode

Min 25

" (64.6 cm)

Max 42" (106.6 cm)

Recirculation Mode (Extension Kit)

Min 40" (106.0 cm)

Max 71

" (180.6 cm)

Recirculation Mode

Min 28

" (72.0 cm)

Max 44

" (113.0 cm)

30" NK30CB700W** (29 7/8" = 75.8 cm)

30" NK30CB600W** (29 7/16" = 74.8 cm)

36" NK36CB700W** (35 3/8" = 89.8 cm)

36" NK36CB600W** (35 3/8" = 89.8 cm)

21 7/8"

(55.5 cm)

8 English

Installation Requirements

Venting Methods

Smoke is exhausted to the outside through a special pipe connected to the hood.

(Recirculating)

Wall Venting

Roof Venting

B. 6" (15.2 cm)

A. Wall cap

B. 6" (15.2 cm)

A. Roof cap

B. 6" (15.2 cm)

Roof Venting Wall Venting (Recirculating)

A. Roof cap

B. 6" (15.2 cm)

A. Wall cap

B. 6" (15.2 cm)

A. Deflector

B. 6" (15.2 cm)

CAUTION

• The minimum connectable exhaust outlet diameter is 6" (15.2 cm).

• Ensure the exhaust outlet diameter and duct diameter match, and then connect

the duct to the wall outlet.

• If the duct and the wall outlet have different diameters, the suction performance

will decrease while also significantly increasing noise.

The manufacturer is not responsible for any problems caused by this.

• Use the minimum possible length for the duct, and do not significantly alter the

cross-section.

• When connecting the duct, minimize bending. (Max bending angle: 90˚)

• In an environment where installing with an external venting method is possible,

be sure to install only using the external venting method.

Parts List

User & Installation

manual (2)

Template for

Installation (1)

Hood Mounting

Bracket (1)

Duct Cover Mounting

Bracket (1)

Electric Damper (1)

NK3*CB700W** only

Damper (1)

NK3*CB600W** only

Damper Adapter (1) Upper Duct Cover (1) Lower Duct Cover (1)

5 mm Magnet (2) Filter Support Cable * (2)

To reduce the risk of the filter dropping, assemble the filter support cable to the filter.

English 9English 9

Installation Requirements

Sub-Parts List

6 x 130 mm

Screw Anchor (2)

6 x 30 mm

Screw Anchor (5)

10 mm

Hood Fixing Screw (10)

22 mm Washer (4)

NOTE

Install the product by using the included accessories and materials appropriately

and according to the installation environment and conditions.

Additional Purchase Accessories

Model NK30CB700W**, NK36CB700W**

Recirculation Kit NK-AR7000WB/AA

Charcoal Filter Kit NK-AF7000WB/AA

Hood Extension Kit NK-AE7000W*/AA

Installation Clearances

Upper furniture Dimension

30" (Min 77.0 cm)

36" (Max 90.0 cm)

Min (Vent) 25 7/16" (64.6 cm)

Min (Recirculation) 28 3/8" (72.0 cm)

Min 11 7/16"

(29.0 cm)

Elec : 46 7/8" – 67 1/2" (119.0 cm – 171.5 cm)

Gas : 51 3/8" – 69 5/16" (130.5 cm – 176.0 cm)

Required Hood installation Height

Elec : 24" – 36" (61.0 cm – 91.4 cm)

Gas : 27" – 36" (68.5 cm – 91.4 cm)

Min (Vent) 25

" (64.6 cm)

Min (Recirculation) 28

" (72.0 cm)

10 English

Installation Requirements

Making a hole in the furniture

Duct hole guide_Op.1

Cabinet floor drilling work: hood exhaust outlet (damper) cutting work

Rear (Wall)

Front

Duct

Hole

Furniture's Center Line

Max

(0.5 cm)

Min

(22.0 cm)

Min 6 5/16" (16.0 cm)

Max 6 11/16" (17.0 cm)

Min

(2.0 cm)

CAUTION

• Cut the cabinet in a way that does not interfere with the damper outlet.

• After assembling the duct cover, make sure that the cut surface of the cabinet is

not exposed. (The hole size must be smaller than the duct cover.)

• Vacuum the sawdust to prevent it from blowing away.

• Make sure the cabinets are not damaged.

• Before cutting the cabinet, explain to the customer that the cabinet needs to be

cut, and then obtain consent before proceeding.

Method and sequence of cutting the upper cabinets

1. Refer to the cutting dimensions above and mark the lines to be cut on the cabinet.

2. Use a jigsaw to cut the upper cabinets. When cutting, use a vacuum cleaner to

minimize the amount of dust.

Installation Tool Jigsaw

Duct hole guide_Op.2

Cabinet floor drilling work: hood exhaust outlet (damper) cutting work

Rear (Wall)

Front

Furniture's Center Line

Cutting Area

13 3/8" (34.0 cm)

CAUTION

• Cut the cabinet in a way that does not interfere with the damper outlet.

• Vacuum the sawdust to prevent it from blowing away.

• Make sure the cabinets are not damaged.

• Before cutting the cabinet, explain to the customer that the cabinet needs to be

cut, and then obtain consent before proceeding.

Method and sequence of cutting the upper cabinets

1. Refer to the cutting dimensions above and mark the lines to be cut on the cabinet.

2. Use a jigsaw to cut the upper cabinets. When cutting, use a vacuum cleaner to

minimize the amount of dust.

Installation Tool Jigsaw, Grinder

English 11English 11

Installation

3. Check the position for fixing the hood

mounting bracket.

또는

길이

130 mm

칼블럭(2 개)

와셔(2 개)

길이

30 mm

칼블럭(2 개)

130 mm

Screw Anchors

(2 pcs.)

or 30 mm

Screw Anchors

(2 pcs.)

and Washers

(2 pcs.)

4. Fix the hood mounting bracket

horizontally on the wall where the

hood is to be installed using screw

anchors, hood mounting bracket

screws, and washers.

Be sure to install it on the wall using

the two 30 mm screw anchors.

NOTE

For a secure hold, use a 130 mm screw

anchor.

CAUTION

• This product must be installed by a professional hood installer.

• If the product is installed on a tiled wall or on drywall, there is a risk of the hood

falling, so be sure to fix the fixing screws to the concrete behind the wall.

• Do not attach the product as if it were a tile or fix it with cement, silicone, or

adhesive. Install it on a concrete wall using the provided screws.

Setting the Location

1. Be sure to check that the product you

have purchased is suitable for the

installation space you have chosen.

24" – 36"

(61.0 cm – 91.4 cm)

27" – 36"

(68.5 cm – 91.4 cm)

2. Fix the enclosed installation template

and then install it so that it does not

twist horizontally.

CAUTION

Please pay attention to the mounting

height. The mounting height is

measured from the top of the range

to the upper cabinets. The mounting

height for an electric cooking surface

is measured from its glass cooktop. For

a gas cooking surface, the mounting

height is measured from the top of the

burning grates.

12 English

Installation

7. Remove the cover by loosening the

screw on the PCB cover.

8. Connect the connector of the electric

damper wire and the PCB connector.

NOTE

Insert the wire into the hole at the top

left corner.

9. Assemble the PCB cover using a

screw.

NOTE

Put the connected connector into the

hole of the cover as shown in the

picture.

Connecting the Vent System

NK3*CB600W**

5. Assemble the damper or the electric

damper for preventing backflow by

turning it in to the hood exhaust

outlet.

NOTE

• Damper is provided in NK3*CB600W**.

• Electric Damper is provided in

NK3*CB700W**.

CAUTION

Check that the electric damper is seated

correctly on the screw thread and there

is no tilt. If the electric damper is not

flush, air will leak through the gap.

NK3*CB700W**

6. Assemble the damper adapter,

pushing it into a damper or electric

damper. Fix it using tape.

NOTE

• If the hood is NK3*CB600W**,

please follow it from No.10.

• If the hood is NK3*CB700W**,

please follow it from No.7.

English 13English 13

Installation

6" (15.2 cm)

12. Fix the duct (6" (15.2 cm)) to the

hood outlet and the vent on the wall,

respectively, with tape.

CAUTION

• Ensure the exhaust outlet diameter and duct diameter match, and then connect

the duct to the wall outlet.

• If the duct and the wall outlet have different diameters, the suction performance

will decrease while significantly increasing noise.

The manufacturer is not responsible for any problems caused by this.

• Use the minimum possible length for the duct, and do not significantly alter the

cross-section.

• Minimize bending when connecting the duct (max bending angle: 90 degrees).

Installing the Range Hood

10. Fix the hood to the hood mounting

bracket installed on the wall.

11. Fix the duct auxiliary bracket using

two 30 mm screw anchors in the top

left of the duct.

14 English

Installation

15. Assemble with 10 mm hood fixing

screws from both sides.

Upper Duct

Lower Duct

16. Assemble the lower duct cover to

the hood. Magnets on the upper duct

cover hold the lower duct cover in

place.

NOTE

The magnet must be attached to the

upper line of the lower duct.

13. Fix the duct cover mounting bracket

to the ceiling or rear wall with the 10

mm hood fixing screws.

CAUTION

• Install the upper duct closely to the

ceiling and upper cabinets.

• Be careful not to let the upper duct

come into contact with the upper

cabinet door.

14. Attach each magnet to the inner

surface of the upper duct cover

overlapping the lower duct cover, and

assemble the upper duct cover in a

way that it fits the mounting bracket.

WARNING

Installation with screws or brackets

other than those specified in the

instruction of this manual may result in

electrical hazards.

NOTE

Magnets are included in the accessory

box.

English 15English 15

Installation

Grounding Pin

CAUTION

Do not ground on gas pipes, water

pipes, telephone lines, etc.

NOTE

Be sure to install a short-circuit breaker

where there is a risk of a short circuit.

17. Remove the filter at the bottom of

the hood.

Assemble the lower duct cover by

fitting a 10 mm hood fixing screw to

the hole in the lower duct cover.

CAUTION

When removing the filter, use both

hands to avoid dropping the filter.

18. When the lower duct cover assembly

is complete, reassemble the filter in

the reverse order of disassembly.

NOTE

To install the extension kit, follow same

process.

WARNING

Be sure to use an outlet with a ground terminal for safety. This can prevent the

risk of electric shock, fire, or malfunction. If the outlet does not have a ground

terminal, purchase a separate grounding wire and connect it to the grounding

line.

16 English

Installation

Installing the Recirculation Kit

NOTE

Same process until No. 14

Duct Cover Mounting Bracket

Deflector Assembly

screws

1. Assemble the air deflector with the

duct cover mounting bracket with the

four assembly screws provided with

the Recirculation Kit.

NOTE

• Use of recirculation type hoods

in closed spaces may cause poor

ventilation performance.

• Please ventilate the room by opening

the windows while operating the

device.

2. Measure from the bottom of the deflector

to the bottom of the hood outlet.

3. Cut the duct to the measured size “X.”

4. Remove the deflector.

5. Slide the duct onto the bottom of the

deflector.

6. Place the assembled deflector and duct

over the exhaust outlet from the hood.

7. Reassemble the air deflector to the duct

cover mounting bracket with the four

assembly screws.

8. Seal the connections with tape.

ADeflector

BX = length to cut

duct

CDuct

DExhaust outlet

Connect the filter support cable

1. Remove the filter at the bottom of

the hood. Pass the filter support

cable through the wire loop attached

on the top of the filter. Make the

knot by passing the hook of the filter

support cable through the other end

of the filter support cable.

2. Hang the hook of the filter support

cable to the anchor at bottom of the

hood. Assemble the filter.

English 17English 17

Installation

10. Attach each magnet to the inner

surface of the upper duct cover

overlapping with the lower duct

cover, and assemble the upper

duct cover in a way that it fits the

mounting bracket.

WARNING

Installation with screws or brackets

other than those specified in the

instruction of this manual may result in

electrical hazards.

NOTE

Magnets are included in the accessory

box.

11. Assemble with 10 mm hood fixing

screws from both sides.

9. Rotate the upper duct as in the

picture.

18 English

Installation

14. Remove the 2 screws from the range

hood.

15. Remove the frame middle part from

the range hood.

16. Remove one screw from the range

hood.

Upper Duct

Lower Duct

12. Assemble the lower duct cover to

the hood. Magnets on the upper duct

cover hold the lower duct cover in

place.

NOTE

The Magnet must be attached to the

upper line of the Lower Duct.

13. Remove metal grease filter from the

range hood.

English 19English 19

Installation

19. Assemble the charcoal filter with the

assembly screw provided with the

Recirculation Kit. Reassemble the

frame middle and filter in the reverse

order of disassembly.

17. Remove the guard by pushing the

hook of the guard in the direction of

the arrow.

18. Insert the charcoal filter hook by

pushing it in the direction of the

arrow.

20 English

Range Hood Description / Overview

Range Hood Description Range Hood Overview

Button panel

01 02 03

01 Light button

• Short press: Changes the light mode (High Low Off)

• 3 second press: Resets the filters

• 5 second press: Activates/deactivates the AP

02 Mode button

• Short press: Changes the operation mode

(Smart Low Medium High (Boost) Smart)

• 3 second press: Language settings (English, Español, Français)

• 5 second press: Deactivates/activates the Wi-Fi

– Smart ventilation mode can be activated on the SmartThings app.

– Range Hood can be operated by mobile device or tablet with registered

Samsung products on the SmartThings app.

• 10 second press: Activates/deactivates Boost mode

* Mode button + Light button

• 3 second press : Changes the default operation mode

– Smart mode is the initial default mode.

03 Power button

• Short press: Turns the device ON/OFF

01 Duct 02 Display 03 Button panel

04 Lamp 05 Filter

La page charge ...

Yes NK30CB700WCG Manuel utilisateur

Marque: Yes

Modèle: NK30CB700WCG

Catégorie: Hottes

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Yes NK30CB700WCG User manual
español: Yes NK30CB700WCG Manual de usuario

Documents connexes

Yes NK30CB600WCG Manuel utilisateur

Yes NK30CB700WCG Manuel utilisateur

Ce manuel convient également à

Yes NK30CB700WCG Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents