Jenn-Air JXW8230WS Le manuel du propriétaire

Marque: Jenn-Air

Modèle: JXW8230WS

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

JENN-AIRTM36"(91.4CM) WALL-MOUNT

CANOPY RANGEHOOD

HOTTEDECUISINII:REJENN-AIRTMPOUR

MONTAGEMURAL36 (91,4 CM)

InstallationInstructionsand Use&Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:

1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.com.

In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.

Instructionsd'installationet Guide d'utilisationetd'entretien

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web _]www.jennair.ca.

Table of Contents/Table des mati_res ..................... 2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION RI_SIDENTIELLE UNIQUEMENT.

JENN-AIR°

LI3UUB/W102743200

TABLEOF CONTENTS

RANGE HOOD SAFETY ................................................................. 3

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Location Requirements ................................................................ 5

Venting Requirements.................................................................. 6

Electrical Requirements ............................................................... 7

INSTALLATION INSTRUCTIONS .................................................. 8

Prepare Location .......................................................................... 8

Install Range Hood ....................................................................... 9

Connect Vent System .................................................................. 9

Install Vent Covers ..................................................................... 10

Complete Installation ................................................................. 10

RANGE HOOD USE ...................................................................... 10

Display ........................................................................................ 10

Light............................................................................................ 11

Timer ........................................................................................... 11

Fan Speed Buttons .................................................................... 11

RANGE HOOD CARE ................................................................... 12

Cleaning ...................................................................................... 12

WIRING DIAGRAM ...................................................................... 13

ASSISTANCE OR SERVICE ......................................................... 14

WAR RANTY .................................................................................. 15

TABLEDESMATIERES

SI_CURITI_ DE LA HOTTE DE CUlSINII_RE ............................... 17

EXIGENCES D'INSTALLATION ................................................... 19

Outils et pieces ........................................................................... 19

Exigences d'emplacement ......................................................... 19

Exigences concernant I'evacuation ........................................... 20

Specifications electriques .......................................................... 22

INSTRUCTIONS D'INSTALLATION ............................................. 23

Preparation de I'emplacement ................................................... 23

Installation de la hotte ................................................................ 24

Raccordement du circuit d'evacuation ...................................... 24

Installation des cache-conduits ................................................. 25

Achever I'installation .................................................................. 25

UTILISATION DE LA HOI-I'E ....................................................... 25

Affichage ..................................................................................... 25

Eclairage ..................................................................................... 26

Minuterie ..................................................................................... 26

Boutons de vitesse du ventilateur .............................................. 26

ENTRETIEN DE LA HOTTE .......................................................... 27

Nettoyage ................................................................................... 27

SCHI_MA DE CABLAGE .............................................................. 28

ASSISTANCE OU SERVICE ......................................................... 29

GARANTIE ..................................................................................... 30

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

• Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

• Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

• Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

• Do not operate any fan with a damaged cord or plug.

Discard fan or return to an authorized service facility for

examination and/or repair.

• Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

• When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

• Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

[] Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

[] Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb6).

[] Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

[] Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: =

[] SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

[] NEVER PICK UP A FLAMING PAN -you may be burned.

[] DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

[] Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

=Based on "Kitchen Fire Safety Tips" published by NFPA.

[] WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

READ AND SAVE THESE INSTRUCTIONS

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Level

• Drill with 1W' (3.0 cm), 3/8"(9.5 mm), and 8Ad'(7.9 mm)

drill bits

• Pencil

• Pliers

• Caulking gun and weatherproof caulking compound

• Vent clamps

• Jigsaw or keyhole saw

• Flat-blade screwdriver

• Metal snips

• Phillips screwdriver

• Wire stripper or utility knife

• Metric Allen wrench set

• Tape measure or ruler

Parts needed

For vented installations, you will also need:

• 1 wall or roof cap

• Metal vent system

For non-vented (recirculating) installations, you will also

need:

• Recirculation Kit Part Number W10272063 for non-vented

(recirculating) installations only. See "Assistance or Service"

section to order.

• 6" (15.2 cm) dia. round metal vent duct - length required is

determined by ceiling height.

Parts supplied

Remove parts from packages. Check that all parts are included.

• Hood canopy assembly with ventilator and light bulbs

installed

• Vent transition with back draft dampers installed

• Metal grease filter(s)

• Vent cover support bracket

• Mounting template

• 2-piece vent cover

• 2 - 3.5 x 6.5 mm screws

• 2 - 2.9 x 6.5 mm screws

• 6- 5 x 45 mm mounting screws

• 2 - 8 x 40 mm wall anchors

• 4- 10 x 50 mm wall anchors

Product Dimensions

81/16" 81/8"

(20.4 cm) (20.7 cm)

*281%o" (73.4 cm) rain.

141/8. 42%o" (107.2 cm) max.

(3_.9cm) I

*'287/8" (73.3 ore) rain.

387/16"(97.6 cm) max.

36" (91.4 cm)

20" (50.8 cm)

*For non-vented (recirculating) installations

**For vented installations

Cabinet Dimensions

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood, It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located behind the left filter on the rear wall of the vent

hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) Installation see "For Non-

vented (recirculating) Installations Only" in "Connect Vent

System" section. Recirculation Kit Part Number W10272063 is

available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

power

supply cable

entry location

Side

cabinet

"/ I "-.. 15" (38.1 cm)

//*+// "%".%_

-- _ 36" (71.4 cm)

x i

bottom of

canopy

to cooking I

surface

iCenterline

Cookinq surface

*For non-vented (recirculating) installations

*NOTE: The range hood chimneys are adjustable and designed

to meet varying ceiling or soffit heights depending on the

distance "X" between the bottom of the range hood and the

cooking surface. For higher ceilings, a Stainless Steel Chimney

Extension Kit Part Number W10272070 is available from your

dealer or an authorized parts distributor. The chimney extension

replaces the upper chimney shipped with the range hood.

IMPORTANT:

Minimum distance "X": 27" (68.6 cm) from electric cooking

surface.

Minimum distance "X": 30" (76.2 cm) from gas cooking

surfaces.

Suggested maximum distance "X": 36" (91.4 cm)

For vented installations, the chimneys can be adjusted for

ceilings between 7' 11" (2.4 m) and 8' 8" (2.6 m).

For non-vented (recirculating) installations, the chimneys can

be adjusted for ceilings between 7' 11" (2.4 m) and 9' 0" (2.7 m).

Ventsystemmustterminatetotheoutdoors,exceptfornon-

Roof Venting

vented (recirculating) installations.

Do not terminate the vent system in an attic or other enclosed

area.

Wall Venting Non-vented

(recirculating)

• Do not use 4" (10.2 cm) laundry-type wall cap.

• Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

• The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

For the most efficient and quiet operation:

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than 1 elbow is used.

• Do not install 2 elbows together.

• Use clamps to seal all joints in the vent system.

• The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

A. Roof cap A. Wall cap A. Deflector

B. 6" (15.2 cm) B. 6" (15.2 cm) B. 6" (15.2 cm)

round vent round vent round vent

• Use caulking to seal exterior wall or roof opening around the

cap.

• The size of the vent should be uniform.

Cold Weather Installations

An additional back draft damper should be installed to minimize

backward cold air flow and a thermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent Piece 6" (15.2 cm) Round

45° elbow 2.5 ft ....

(0.8 m)

Makeup Air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Venting Methods

This canopy hood is factory set for venting through the roof or

wall.

A 6" (15.2 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 6" (15.2 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates

back pressure and air turbulence that greatly reduce

performance.

Vent system can terminate either through the roof or wall. To vent

through a wall, a 90° elbow is needed.

Rear discharge

A 90° elbow may be installed immediately above the hood.

For Non-Vented (recirculating) Installations

If it is not possible to vent cooking fumes and vapors to the

outside, the hood can be used in the non-vented (recirculating)

version, fitting a charcoal filter and the deflector. Fumes and

vapors are recycled through the top grille.

90° elbow 5.0 ft

(1.5m)

Maximum equivalent vent length is 35 ft (10.7 m).

Example vent system

,oo I o. ....W°,,

The following example falls within the maximum recommended

vent length of 35 ft (10.7 m).

1 - 90 ° elbow = 5.0 ft (1.5 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Length of system = 13.0 ft (3.9 m)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

• The grounded 3 prong outlet is to be located above the range

hood at a maximum distance of 337_e'' (85.0 cm) from where

the power cord exits the hood. See illustration.

337/%"

(85 cm)

[

IMPORTANT: The range hood must be electrically grounded in

accordance with local codes and ordinances, or in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70

(latest edition) or Canadian Electrical Code, CSA C22.1

No. 0-M91 (latest edition).

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

• A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical

circuit is required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this range hood be provided.

• This range hood is equipped with a power supply cord having

a 3 prong grounding plug.

• To minimize possible shock hazard, the cord must be

plugged into a mating, 3 prong, grounding-type outlet,

grounded in accordance with local codes and ordinances. If a

mating outlet is not available, it is the personal responsibility

and obligation of the customer to have the properly grounded

outlet installed by a qualified electrician.

GROUNDING INSTRUCTIONS

• For a grounded, cord-connected range hood:

This range hood must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of electric

shock by providing an escape wire for the electric current.

This range hood is equipped with a cord having a grounding

wire with a grounding plug.The plug must be plugged into

an outlet that is properly installed and grounded.

WARNING: Improper grounding can result in a risk of

electric shock.

Consult a qualified electrician if the grounding instructions

are not completely understood, or if doubt exists as to

whether the range hood is properly grounded.

Do not use an extension cord. If the power supply cord is too

short, have a qualified electrician install an outlet near the

range hood.

SAVE THESE INSTRUCTIONS

INSTALLATIONINSTRUCTIONS

• It is recommended that the vent system be installed before 8. Mark centers of the fastener locations through the template

hood is installed, to the wall.

• Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

• Check your ceiling height and the hood height maximum

before you select your hood.

1. Disconnect power.

2. Determine which venting method to use: roof, wall, or non-

vented.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

5. Determine and mark the centerline on the wall where the

canopy hood will be installed.

6. Select a mounting height between a minimum of

27" (68.6 cm) for an electric cooking surface, a minimum

of 30" (76.2 cm) for a gas cooking surface, and a suggested

maximum of 36" (91.4 cm) above the range to the bottom

of the hood. Mark a reference line on the wall.

7. Tape template in place, aligning the template centerline and

bottom of template with hood bottom line and with the

centerline marked on the wall.

:......................................A

d,! ..........

10.

IMPORTANT: All screws must be installed into wood. If there

is no wood to screw into, additional wall framing supports

may be required.

Remove the template.

Drill 3Ad'(4.8 mm) pilot holes at all locations where screws are

being installed into wood.

Install the 2 - 5 x 45 mm mounting screws. Leave a

1/4"(6.4 mm) gap between the wall and the back of the

screw head to slide range hood into place.

(6.4rnrn) _

Vent Cover Support Bracket Installation

Installations using telescoping upper and lower vent cover

assembly

1. Position vent cover bracket on wall about 1/8"(3.0 mm) away

from the ceiling.

2. Mark the hole locations.

3. Drill 3/8"(9.5 mm) holes for wall anchors and insert anchors

flush with the wall.

A. 8 x 40 mm drywall anchors

B. Centerline on wall

C. Vent cover support bracket

D. 5 x 45 mm screws

4. Attach vent cover support bracket to wall.

Complete Preparation

1. Determine and make all necessary cuts in the wall for the vent

system. Install the vent system before installing the hood. See

"Venting Requirements" section.

2. Use caulk to seal all openings.

A. Centerline

B. Fastener locations

C. Mounting height reference

Using 2 or more people, hang range hood on 2 mounting

screws through the mounting slots on back of hood.

A I

For non-vented (recirculating) installation only:

1. Assemble the air deflector with the duct cover bracket with

2 - assembly screws provided with the Recirculation Kit.

A. Mounting screws

B. Mounting slots

C. Lower mounting screws

2. Remove the grease filter. See "Range Hood Care" section.

3. Level the range hood and tighten upper mounting screws.

4. Install 2 - 5 x 45 mm lower mounting screws and tighten.

Install transition on top of hood (if removed for shipping) with

2 - 3.5 x 6.5 mm sheet metal screws.

A. Vent transition

B. 3.5 x 6.5 mm screw

For vented installations only:

1. Fit vent system over transition piece.

2. Seal connection with clamps.

3. Check that back draft dampers work properly.

A. Ventcover bracket

B.2.9 x 6.5 mm screws

C.Deflector

Measure from the bottom of the air deflector to the bottom of

the hood outlet.

g ................................

X---------------------C

E .............

A.Air deflector

B. Ventclamp

C.X = length to cut vent duct

D. Ventduct

E.Exhaustoutlet

Cut the duct to the measured size (X).

Remove the air deflector.

Slide the duct onto the bottom of the air deflector.

Place the assembled air deflector and duct over the exhaust

outlet from the hood.

Reassemble the air deflector to the duct cover bracket with

2 assembly screws.

8. Sealconnectionswithventclamps.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to folow these instructions can result in death,

fire, or electrical shock.

9. Plug 3 prong power cord into a grounded 3 prong outlet

located above the range hood.

n C

When using both upper and lower vent covers, push lower cover

down onto hood and lift upper cover to ceiling and install with

two 2.9 x 6.5 mm screws.

NOTE: For vented installations, the upper vent cover may be

reversed to hide slots.

A. Upper vent cover

B. Lower vent cover

C. 2.9 x 6.5 mm screws

D. Bracket

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the

kitchen.

The range hood controls are located on the front side of the

canopy.

A. Louver holes (non-vented

[recirculating] installations only)

B.Duct covers

C. Canopy

D. Grease filters

E. Lamp housings

F. Grease filter handles

G. Control panel

Control Panel

The range hood controls are located on the front side of the

canopy.

A B C D E

[_o.........................

:_ IIJENN-AIR BSBB

Q Clean grease fll er

A.Power decrease

B.Power increase

C.Display

D.Light

E.Timer

1. For non-vented (recirculating) installations only, install

charcoal filters over grille on blower housing. See the "Range

Hood Care" section.

2. Install metal filters. See the "Range Hood Care" section.

3. Check the operation of the range hood blower and light. See

the "Range Hood Use" section.

NOTE: To get the most efficient use from your new range hood,

read the "Range Hood Use" section.

Grease Filter Saturation Alarm

After 30 hours of fan function, the display will show "Clean

Grease Filter" when the fan is active. When this icon shows in the

display, the installed grease filters should be washed. See

"Range Hood Care" section.

• To reset the grease filter saturation alarm, press and hold the

POWER INCREASE button for 5 seconds. The "Clean Grease

Filter" icon will no longer be displayed.

Charcoal Filter Saturation Alarm

After 120 hours of fan function, the display will show "Replace

Charcoal Filter" when the fan is active. When this icon shows in

the display, the charcoal filters should be replaced. See "Range

Hood Care" section.

• To reset the charcoal filter saturation alarm, press and hold

the POWER DECREASE button for 5 seconds. The "Replace

Charcoal Filter" icon will no longer be displayed.

Audible Signal Activation and Deactivation

The audible signals can be activated or deactivated by pressing

the "LIGHT" button for 5 seconds.

• If the audible signal is activated, a tone will sound, and "Snd"

symbol will appear in the display for 3 seconds.

• If the audible signal is deactivated, the "Snd" symbol will

appear on the display for 3 seconds.

Charcoal Filter (Recirculation Accessory) Inclusion and

Exclusion

When the charcoal filter is in use (recirculating mode), press and

hold the POWER DECREASE and POWER INCREASE buttons at

the same time for 5 seconds. "Able" will appear in the display for

3 seconds.

If the charcoal filter is not used (vented mode), press and hold the

POWER DECREASE and POWER INCREASE buttons at the

same time for 5 seconds. "None" will appear in the display for

3 seconds.

• When the charcoal filter has been excluded, the charcoal filter

alarm is disabled.

• The inclusion or exclusion of the charcoal filter must be

selected while the lights and the fan motor are Off.

Heat Sensor

The control is equipped with a heat sensor that will turn on the

blower to the highest speed if excessive heat occurs around the

control area.

• If the blower is On or Off, the blower will automatically set to

the highest speed. "Auto" will appear in the display to

indicate that the heat sensor has detected excessive heat.

• When the blower is operating due to excessive heat detected

by the heat sensor, the blower speed cannot be decreased.

• When the temperature level on the hood drops to normal, the

blower will return to its setting before the excessive heat was

sensed.

To operate the light:

1. Press the Light button to turn the light on to high.

2. Press the Light button again to turn the light to low.

3. Press the Light button a third time to turn the light off.

The timer can be set from 1 to 60 minutes. The default timer

setting is 10 minutes.

To use the timer:

1. Press the Timer button to enter the timer mode. After

5 seconds the default time will be automatically selected.

2. Press the POWER DECREASE and POWER INCREASE

buttons while the display is flashing (5 seconds) to adjust to

the desired time. Pressing the timer button again or waiting

5 seconds after selecting the desired time will start the timer

countdown.

3. The timer can be canceled at any time by pressing the Timer

button again.

NOTE: During the timer setup, the Power Decrease and Power

Increase buttons are dedicated to the timer. After the timer starts,

the Power Decrease and Power Increase buttons can be used for

other functions.

Power Increase/On

This button is used to turn the fan On or increase the fan speed.

• The fan will turn On if the Power Increase button is pressed

and the hood was Off.

• An audible tone will sound when the fan reaches its highest

speed.

Power Decrease/Off

• This button is used to turn the fan Off or to decrease the fan

speed.

RANGE HOOD CARE

IMPORTANT: Clean the hood and grease filters frequently

according to the following instructions. Replace grease filters

before operating hood.

Exterior Surfaces:

To avoid damage to the exterior surface, do not use steel wool or

soap-filled scouring pads.

Always wipe dry to avoid water marks.

Cleaning Method:

• Liquid detergent soap and water, or all-purpose cleanser

• Wipe with damp soft cloth or nonabrasive sponge, then rinse

with clean water and wipe dry.

Metal Grease Filter

The filters should be washed frequently. Place metal filters in

dishwasher or hot detergent solution to clean.

Let filter dry thoroughly before replacing it.

Turn off fan and lights. Allow halogen lamp to cool.

1. Remove each filter by pulling the spring release handle and

then pulling down the filter.

A. Spring release handle

2. Wash metal filters as needed in dishwasher or hot detergent

solution.

3. Reinstall the filter by making sure the spring release handles

are toward the front. Insert metal grease filter into upper

track.

4. Pull the spring release handle down.

5. Push up on metal filter and release handle to latch into place.

6. Repeat steps 1-5 for the other filter.

Non-Vented (recirculating) Installation Filters

The charcoal filter is not washable. It should last up to 6 months

with normal use. Replace with Charcoal Filter Kit Number

W10272068.

To replace charcoal filter:

1. Cover the grille that covers the blower motor with the

charcoal filter so that the slots on the filter correspond to the

pins on the sides of the motor grille.

A. Charcoal filter

B. Pins

C. Blower motor

2. Turn the charcoal filter clockwise to lock it.

3. Repeat steps 1-2 on the other filter.

Replacing a Halogen Lamp

Turn off the range hood and allow the halogen lamp to cool. To

avoid damage or decreasing the life of the new bulb, do not

touch bulb with bare fingers. Replace bulb, using tissue or

wearing cotton gloves to handle bulb.

If new lamps do not operate, make sure the lamps are inserted

correctly before calling service.

1. Disconnect power.

2. Push up on the lens and turn it counterclockwise.

Remove the bulb and replace it with a 120-volt, 50-watt

maximum halogen bulb with a GU10 base. Turn it clockwise

to lock it into place.

Repeat steps 2-3 for the other bulb if needed.

Reconnect power.

WIRING DIAGRAM

IXSA

Electronic User Interface

[

Electronic Power Board

CON1

L[[_ &_ 4

_>-

(_5

S3 S2 Sl

P8 P7 P6

13 12

rr _

_CON4

Y/G

COLOR TABLE

BK BLACK

BU BLUE

BR BROWN

G GREEN

GY GREY

COLOR TABLE

R RED

W WHITE

Y YELLOW

Y/G YELLOW/GREEN

ASSISTANCEOR SERVICE

When calling for assistance or service, please know the purchase

date and the complete model and serial number of your

appliance. This information will help us to better respond to your

request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance. To locate factory

specified replacement parts in your area, call us or your nearest

designated service center.

Call the dealer from whom your appliance was purchased, or call

1-800-JENNAIR (1-800-536-6247) to locate an authorized

service company. When calling, please know the purchase date

and the complete model and serial number of your appliance. Be

sure to retain proof of purchase to verify warranty status.

If the dealer or service company cannot resolve your problem,

write to:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Web address: www.jennair.com

Or call: 1-800-536-6247

U.S. customers using -I-I-Yfor deaf, hearing impaired or speech

impaired, call: 1-800-688-2080 (Monday - Friday, 8:00 a.m. -

8:00 p.m. Eastern Time).

NOTE: When writing or calling about a service problem, please

include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt).

User's guides, service manuals and parts information are

available from Jenn-Air Brand Home Appliances, Customer

eXperience Center.

Charcoal Filter Kit

(for non-vented installations only)

Order Part Number W10272068

Recirculation Kit

(for non-vented installations only)

Order Part Number W10272063

Chimney Extension Kit

Order Part Number W10272070

Call the dealer from whom your appliance was purchased, or call

Jenn-Air at 1-800-807-6777 to locate an authorized service

company. When calling, please know the purchase date and the

complete model and serial number of your appliance. Be sure to

retain proof of purchase to verify warranty status.

If the dealer or service company cannot resolve your problem,

write to:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Web address: www.jennair.ca

Or call: 1-800-807-6777.

NOTE: When writing or calling about a service problem, please

include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt).

User's guides, service manuals and parts information are

available from Jenn-Air Brand Home Appliances, Customer

eXperience Centre.

JENN-AIR MAJOR APPLIANCEWARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Jenn-Air brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Jenn-Air") will pay for factory

specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Jenn-Air designated

service company. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used

in the country in which it was purchased. Outside the 50 United States and Canada, this limited warranty does not apply. Proof of

original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is

contrary to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by Jenn-Air.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Jenn-Air within 30 days from the date of purchase.

6. Any food loss due to refrigerator or freezer product failures.

7. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be

repaired in the home and only in-home service is covered by this warranty.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Jenn-Air servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with published installation instructions.

11. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty

is void if the factory applied serial number has been altered or removed from your major appliance.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. JENN-AIR SHALL NOT BE LIABLE FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

If outside the 50 United States and Canada, contact your authorized Jenn-Air dealer to determine if another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," you may find

additional help by checking the "Assistance or Service" section or by calling Jenn-Air. In the U.S.A., call 1-800-536-6247. In Canada,

call 1-800-807-6777. 6/09

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

SECURITEDELA HOTTEDECUISINIERE

Votre securite et celle des autres est tres importante.

Nous donnons de nombreux messages de securite importants dans ce manuel et sur votre appareil menager. Assurez-vous de

toujours lire tousles messages de securite et de vous y conformer.

Voici le symbole d'alerte de securit&

Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves & vous

et &d'autres.

Tous les messages de securite suivront le symbole d'alerte de securite et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d_cbs ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d_cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tousles messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

llVIPORTANTES iNSTRUCTiONS DE Sl CURITl

AVERTISSEMENT : POUR REDUIRE LE RISQUE

D'INCENDIE, CHOC ¢:LECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

m Utiliser cet appareil uniquement dans les applications

envisag_es par le fabricant. Pour toute question, contacter

le fabricant.

m Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre I'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour emp6cher tout r_tablissement accidentel de

I'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur le tableau

de disjoncteurs une 6tiquette d'avertissement pro6minente

interdisant le r@ablissement de I'alimentation.

m Tout travail d'installation ou c&blage 61ectrique doit @re

r6alis_ par une personne qualifi6e, dans le respect des

prescriptions de tous les codes et normes applicables, y

compris les codes du b&timent et de protection contre les

incendies.

m Ne pas faire fonctionner un ventilateur dont le cordon ou la

fiche est endommag6(e). Jeter le ventilateur ou le retourner

&un centre de service agr66 pour examen et/ou r6paration.

m Une source d'air de d_bit suffisant est n6cessaire pour le

fonctionnement correct de tout appareil a gaz (combustion

et 6vacuation des gaz & combustion par la chemin6e), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de I'_quipement de chauffage et

les prescriptions des normes de s_curit_ - comme celles

publi_es par la National Fire Protection Association (NFPA)

et I'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorit6s r6glementaires locales.

m Lors d'op@ations de d6coupage et de per£age dans un mur

ou un plafond, veiller a ne pas endommager les c&blages

61ectriques ou canalisations qui peuvent s'y trouver.

m Les ventilateurs d'6vacuation doivent toujours d6charger

I'air a I'ext@ieur.

MISE EN GARDE : Cet appareil est congu uniquement

pour la ventilation g6n@ale. Ne pas I'utiliser pour I'extraction

de mati_res ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et 6vacuer ad6quatement les gaz, veiller & acheminer I'air

aspir6 par un conduit jusqu'b, I'ext@ieur - ne pas d6charger

I'air aspir6 dans un espace vide du b&timent comme une

cavit_ murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR REDUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

METALLIQUES.

AVERTISSEMENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINIF:RE :

[] Ne jamais laisser un _16ment de surface fonctionner &

puissance de chauffage maximale sans surveillance. Un

renversement/d6bordement de mati@e graisseuse pourrait

provoquer une inflammation et la g6n@ation de fum_e.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

[] Veiller &toujours faire fonctionner le ventilateur de la hotte

Iors de la cuisson avec une puissance de chauffage _lev_e

ou Iors de la cuisson d'un mets &flamber (& savoir crSpes

Suzette, cerise jubil6e, steak au poivre flamb6).

[] Nettoyer fr6quemment les ventilateurs d'extraction. Veiller &

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

[] Utiliser toujours un ustensile de taille appropri6e. Utiliser

toujours un ustensile adapt_ & la taille de 1'616ment

chauffant.

AVERTISSEMENT : POUR REDUIRE LE RISQUE DE

DOMMAGES CORPORELS APR_:S LE DECLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINI_:RE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :a

[] Placer sur le r6cipient un couvercle bien ajust_,, une t61e &

biscuits ou un plateau m6tallique POUR ETOUFFER LES

FLAMMES, puis @eindre le brt_leur. VEILLER ,_ ¢:VITER

LES BRULURES. Si les flammes ne s'_teignent pas

imm_diatement, CVACUER LA PIECE ET APPELER LES

POMPIERS.

[] NE JAMAIS PRENDRE EN MAIN UN RECIPIENT

ENFLAMMt _ - vous risquez de vous brQler.

[] NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brQlante.

[] Utiliser un extincteur SEULEMENT si :

- IIs'agit d'un extincteur de classe ABC, dont on connaft le

fonctionnement.

- IIs'agit d'un petit feu encore limit6 & I'endroit oQ il s'est

d6clar&

- Les pompiers ont 6t_ contact,s.

- IIest possible de garder le dos orient_ vers une sortie

pendant I'op@ation de lutte contre le feu.

aRecommandations tir_es des conseils de s_curit_ en cas

d'incendie de cuisine publi_s par la NFPA.

[] AVERTISSEMENT : Pour r_duire le risque d'incendie

ou de choc _lectrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de r_glage de la vitesse & semi-

conducteurs.

LIRE ET CONSERVER CES INSTRUCTIONS

EXIGENCESD'INSTALLATION

Rassembler les outils et pieces necessaires avant d'entreprendre

I'installation. Lire et observer les instructions fournies avec

chacun des outils de la liste ci-dessous.

Outils n_cessaires

• Niveau

• Perceuse avec des forets de 11¼"(3 cm), 3/8"(9,5 mm)

et %e" (7,9 mm)

• Crayon

• Pince & denuder ou couteau utilitaire

• Metre-ruban ou regle

• Pince

• Pistolet & calfeutrage et compose de calfeutrage resistant

aux intemperies

• Brides deserrage

• Scie sauteuse ou scie &guichet

• Tournevis & lame plate

• Cisaille de ferblantier

• Tournevis Phillips

• Ensemble de cles Allen (systeme metrique)

Pi_ces n_cessaires

Pour les installations avec d_charge a I'ext_rieur, il faudra

aussi :

• 1 bouche de decharge (decharge a travers lemur ou & travers

le toit)

• Circuit d'evacuation metallique

Pour les installations sans d_charge a I'ext_rieur (recyclage),

il faudra aussi :

• Ensemble de recyclage, piece numero W10272063 pour les

installations sans decharge & I'exterieur (recyclage)

uniquement. Voir la section "Assistance ou service" pour

commander.

Conduit d'evacuation metallique circulaire de 6" (15,2 cm) de

diametre - Iongueur necessaire determinee par la hauteur de

plafond.

Pi_ces fournies

Retirer les pieces de leur emballage. Verifier que toutes les

pieces sont presentes.

• Auvent de hotte avec ventilateur et ampoules installes

• Raccord de transition avec clapets anti-reflux installes

• Filtre(s) a graisse metallique(s)

• Bride de support du cache-conduit

• Gabarit de montage

• Cache-conduit- 2 pieces

• 2 vis de 3,5 x 6,5 mm

• 2 vis de 2,9 x 6,5 mm

• 6 vis de montage de 5 x 45 mm

• 2 chevilles d'ancrage mural de 8 x 40 mm

• 4 chevilles d'ancrage mural de 10 x 50 mm

IMPORTANT : Observer les dispositions de tousles codes et

reglements en vigueur.

Confier I'installation de la hotte & un technicien qualifi& C'est &

I'installateur qu'incombe la responsabilite de respecter les

distances de separation specifiees sur la plaque signaletique de

I'appareil. La plaque signaletique de I'appareil est situee derriere

le filtre de gauche, sur la paroi arriere de la hotte.

On doit toujours installer la hotte & distance des sources de

courant d'air (fen_tres, portes et bouches de chauffage).

Respecter les dimensions indiquees pour les ouvertures &

decouper dans les placards. Ces dimensions tiennent compte

des valeurs minimales des degagements de separation.

On doit disposer d'une prise de courant electrique reliee & la

terre. Voir la section "Specifications electriques".

La hotte est configuree & I'usine pour une decharge & travers le

toit ou un mur. Pour une installation sans decharge & I'exterieur

(recyclage), voir "Installations sans decharge a I'exterieur

(recyclage) uniquement", & la section "Raccordement du circuit

d'evacuation". L'ensemble de recyclage (piece numero

W10272063) est disponible chez votre marchand ou chez un

distributeur de pieces autoris&

On doit assurer I'etancheite au niveau de chaque ouverture

decoupee dans le plafond et lemur oQ la hotte sera installee.

Installation dans une r_sidence mobile

L'installation de cette hotte doit satisfaire aux exigences de la

norme Manufactured Home Construction Safety Standards, Titre

24 CFR, partie 328 (anciennement Federal Standard for Mobile

Home Construction and Safety, titre 24, HUD, partie 280); Iorsque

cette norme n'est pas applicable, I'installation doit satisfaire aux

criteres de la plus recente edition de la norme Manufactured

Home Installation 1982 (Manufactured Home Sites, Communities

and Setups)ANSI A225.1/NFPA 501A, ou des codes Iocaux.

Dimensions du produit

8V_d' 8W'

(20,4 crn) (20,7 cm)

*28_%d ' (73,4 crn) rain.

14W' 42_/_d' (107,2 cm) max.

(s_,9ore) I

*'287/8" (73,3 Ore) rain.

387/16'' (97,6 cm) max.

36" (91.4 crn)

10W'

cm)

20" (50,8 crn)

*Installations sans decharge & I'exterieur (recyclage)

**Installations avec decharge a I'exterieur

65/8"

7%" (18,8 crn)

Placard

adjacent

Pointd'entr_e

du circuit

d'_vacuation

et du c_ble

d'aiimentation

i...........J...........i _lectrique

...."...... 'i .........!5" (38,1 crn)

Placard

adjacent

36" (91,4 crn)

Distance "X"

entre le bas de

I'auvent et la

elLirlaoe de CILIJeson

Axe central

Surface de cuisson

*Installations sans decharge a I'exterieur (recyclage)

*REMARQUE • Les cache-conduits de hotte sont reglables; on

peut les ajuster en fonction de la hauteur disponible sous

plafond ou soffite, selon la distance "X" entre le bas de la hotte

et la surface de cuisson. Pour des plafonds de hauteur

superieure, un ensemble d'extension de cache-conduit en acier

inoxydable, piece numero W10272070 est disponible chez votre

marchand ou chez un distributeur de pieces autoris&

L'extension de cache-conduit remplace la section superieure du

cache-conduit fournie avec la hotte.

IMPORTANT •

Valeur minimale de la distance "X" : 27" (68,6 cm) a partir de

la surface de cuisson electrique.

Distance minimale "X" : 30" (76,2 cm) a partir d'une surface

de cuisson au gaz.

Distance maximale "X" suggeree : 36" (91,4 cm)

Pour les installations avec decharge & I'exterieur, on peut

ajuster les cache-conduits pour une hauteur sous plafond de

7' 11" (2,4 m) et 8' 8" (2,6 m).

Pour une installation sans decharge & I'exterieur (recyclage), on

peut ajuster les cache-conduits pour une hauteur sous plafond

entre 7' 11" (2,4 m) et 9' 0" (2,7 m).

• Le circuit d'evacuation doit decharger I'air & I'exterieur,

excepte pour une installation sans decharge a I'exterieur

(recyclage).

• Ne pas terminer le circuit d'evacuation dans un grenier ou

dans un autre espace ferme.

• Ne pas utiliser une bouche de decharge murale de

4" (10,2 cm) normalement utilisee pour un equipement de

buanderie.

• Utiliser uniquement du conduit metallique. Le conduit en

metal rigide est recommand& Ne pas utiliser de conduit de

plastique ou en feuille metallique.

• La Iongueur du circuit d'evacuation et le nombre de coudes

doit etre reduit au minimum pour fournir la meilleure

performance.

Pour un fonctionnement efficace et silencieux •

• Ne pas utiliser plus de trois coudes a 90°.

• Veiller & ce qu'il y ait une section droite de conduit de

24" (61,0 cm) ou plus entre deux coudes, si on doit utiliser

plus de un raccord coud&

• Ne pas connecter 2 coudes ensemble.

• Au niveau de chaque jointure du circuit d'evacuation, assurer

I'etancheite avec les brides de serrage pour conduit.

• Le circuit d'evacuation doit comporter un clapet anti-reflux. Si

la bouche de decharge murale ou par le toit comporte un

clapet, ne pas utiliser le clapet fourni avec la hotte.

• Autour de la bouche de decharge a I'exterieur (mur ou toit),

assurer I'etancheite avec un compose de calfeutrage.

• La taille du conduit doit etre uniforme.

Installation dans une r_gion & climat froid

On doit installer un clapet anti-reflux additionnel pour minimiser

le reflux d'air froid, et incorporer un element d'isolation thermique

pour minimiser la perte de chaleur par conduction par

I'intermediaire du circuit d'evacuation, de I'interieur de la maison

I'exterieur. Le clapet anti-reflux doit etre place du c6te froid par

rapport a I'element d'isolation thermique.

L'element d'isolation thermique doit etre aussi proche que

possible de I'endroit oQ le circuit d'evacuation penetre la partie

chauffee de la maison.

Air d'appoint

Le code du b&timent local peut exiger I'emploi d'un systeme de

renouvellement de I'air/introduction d'air d'appoint, Iors de

I'utilisation d'un systeme d'aspiration de debit superieur a une

valeur (pieds cubes par minute) specifiee. Le debit specifiC, pieds

cubes par minute, est variable d'une juridiction & une autre.

Consulter un professionnel des installations de chauffage/

ventilation/climatisation au sujet des exigences specifiques

applicables dans la juridiction locale.

La page charge ...

Jenn-Air JXW8230WS Le manuel du propriétaire

Marque: Jenn-Air

Modèle: JXW8230WS

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Jenn-Air JXW8230WS Owner's manual

Jenn-Air JXW8230WS Le manuel du propriétaire

Ce manuel convient également à

Jenn-Air JXW8230WS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents