Jenn-Air JXW5036WS Le manuel du propriétaire

Marque: Jenn-Air

Modèle: JXW5036WS

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

JENN-AIR_30"AND 36"(76.2CM AND 91.4 CM)

WALL-MOUNTCANOPY RANGEHOOD

HOTE DECU

MURAL30"ET36"7(6,2CM ET91,4CM)

InstallationInstructionsand Use&Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:

1-800-JennAir (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.

Instructionsd'installationetGuide d'utilisationetd'entretien

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web a www.jennair.ca.

Table of Contents/Table des matieres ................... 2

IMPORTANT: READ AND SAVE THESE iNSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION RI_SIDENTIELLE UNIQUEMENT.

JENN-AIR°

LI3U 1B/W10274303G

TABLEOF CONTENTS

RANGE HOOD SAFETY ................................................................. 3

INSTALLATION REQUIREMENTS ................................................ 5

Tools and Parts ............................................................................ 5

Location Requirements ................................................................ 5

Venting Requirements .................................................................. 6

Electrical Requirements ............................................................... 7

INSTALLATION INSTRUCTIONS .................................................. 7

Prepare Location .......................................................................... 7

Install Range Hood ....................................................................... 8

Connect Vent System .................................................................. 9

Make Electrical Connection ....................................................... 10

Install Vent Covers ..................................................................... 10

Install Filters................................................................................ 11

Complete Installation ................................................................. 11

RANGE HOOD USE ...................................................................... 11

Display ........................................................................................ 11

Light............................................................................................ 12

Tim er........................................................................................... 12

Fan Speed Buttons .................................................................... 12

RANGE HOOD CARE ................................................................... 12

Cleaning ...................................................................................... 12

WIRING DIAGRAM ...................................................................... 14

ASSISTANCE OR SERVICE ......................................................... 15

WAR RANTY .................................................................................. 16

TABLEDESMATIERES

SI_CURITI_ DE LA HOTTE DE CUlSINII_RE ............................... 18

EXIGENCES D'INSTALLATION ................................................... 20

Outillage et pieces ...................................................................... 20

Exigences d'emplacement ......................................................... 20

Exigences concernant I'evacuation ........................................... 21

Specifications electriques .......................................................... 22

INSTRUCTIONS D'INSTALLATION ............................................. 23

Preparation de I'emplacement ................................................... 23

Installation de la hotte ................................................................ 24

Raccordement du circuit d'evacuation ...................................... 24

Raccordement electrique ........................................................... 25

Installation du cache-conduit ..................................................... 26

Installation des filtres .................................................................. 26

Achever I'installation .................................................................. 26

UTILISATION DE LA Ho'n'E ....................................................... 26

Afficheur ..................................................................................... 27

€:clairage ..................................................................................... 27

Minuterie ..................................................................................... 27

Boutons de vitesse du ventilateur .............................................. 27

ENTRETIEN DE LA HOTTE DE CUlSINII_RE ............................. 28

Nettoyage ................................................................................... 28

SCHI_MA DE C.&,BLAGE.............................................................. 29

ASSISTANCE OU SERVICE ......................................................... 30

GARANTIE ..................................................................................... 31

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

[] Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

[] Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

[] Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

[] Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

[] When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

[] Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

[] Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

[] Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb6).

[] Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

[] Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: a

[] SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

[] NEVER PICK UP A FLAMING PAN -you may be burned.

[] DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

[] Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.

[] WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

READ AND SAVE THESE iNSTRUCTiONS

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Level

• Drill with 11¼'' (3.0 cm), 3/8"(9.5 mm), 7/64"(2.75 mm) and

1/8"(3.0 mm) drill bits

• Pencil

• Wire stripper or utility knife

• Tape measure or ruler

• Pliers

• Caulking gun and weatherproof caulking compound

• Vent clamps

• Jigsaw or keyhole saw

• Flat-blade screwdriver

• Metal snips

• Phillips screwdriver

Parts needed

• Home power supply cable

• 1/2"(12.7 mm) UL listed or CSA approved strain relief

• 3 UL listed wire connectors

For vented installations, you will also need:

• 1 wall or roof cap

• Metal vent system

For non-vented (recirculating) installations, you will also

need:

• Recirculation Kit Part Number W10272064 for non-vented

(recirculating) installations only. See "Assistance or Service"

section to order.

Parts supplied

Remove parts from packages. Check that all parts are included.

• Hood canopy assembly with ventilator and light bulbs

installed

• 2 glass mounting brackets

• Vent transition with back draft dampers installed

• Blower support bracket

• Glass mantle

• Vent cover support bracket (3 pieces)

• Mounting template

• 2-piece vent cover

• 2 - 2.9 x 6.5 mm screws

• 8-4x8mmscrews

• 6- 5 x 45 mm mounting screws

• 2- 8 x 40 mm wall anchors

• 4- 10 x 50 mm wall anchors

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located behind the left filter on the rear wall of the vent

hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) Installation see "For Non-

vented (recirculating) Installations" in "Connect Vent System"

section. Recirculation Kit Part Number W10272064 is available

from your dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

Product Dimensions

35" (88.9 cm) mh

"60 3/4" (154.3 crn)

56 s,46"(143.0 crn)

(50 cm)

30" - 36"

(78.2 crn - 91.4 crn)

*For non-vented (recirculating) installations

Installation Dimensions

11%"

13%"

*8" (20.3 cm) rain.

2" (5.1 cm) rain.

(36 cm) vent and power

supply cable entry

location

26 7/8"

(68cm)

side I side

cabinet _;;;;;;;;i;._ ......::i.;;;;; ,_.;_i_ cabinet

, i<ji:i2o

"X" bottom

of canopy to

cooking surface

centerline cooking surface

*For non-vented (recirculating) installations

IMPORTANT:

Minimum distance "X": 24" (61.0 cm) from electric cooking

surface.

Minimum distance "X": 27" (68.6 cm) from gas cooking

surfaces.

Suggested maximum distance "X": 36" (91.4 cm)

For vented installations, the chimneys can be adjusted for

ceilings between 8' (2.44 m) and 10' 2" (3.1 m).

For non-vented (recirculating) installations, the chimneys can

be adjusted for ceilings between 8' (2.44 m) and 10' 6" (3.2 m).

*NOTE: The range hood chimneys are adjustable and designed to

meet varying ceiling or soffit heights depending on the distance

"X" between the bottom of the range hood and the cooking

surface. For higher ceilings, a Stainless Steel Chimney Extension

Kit Part Number W10272071 is available from your dealer or an

authorized parts distributor. The chimney extension replaces the

upper chimney shipped with the range hood.

Vent system must terminate to the outdoors, except for non-

vented (recirculating) installations.

Do not terminate the vent system in an attic or other enclosed

area.

• Do not use 4" (10.2 cm) laundry-type wall cap.

• Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

• The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

For the most efficient and quiet operation:

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than 1 elbow is used.

• Do not install 2 elbows together.

• Use clamps to seal all joints in the vent system.

The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

• Use caulking to seal exterior wall or roof opening around the

cap.

• The size of the vent should be uniform.

Cold Weather Installations

An additional back draft damper should be installed to minimize

backward cold air flow and athermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup Air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Venting Methods

This canopy hood is factory set for venting through the roof or

wall.

A 8" (20.0 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 8" (20.0 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates

back pressure and air turbulence that greatly reduce

performance.

Vent system can terminate either through the roof or wall. To vent

through a wall, a 90° elbow is needed.

Rear discharge

A 90° elbow may beinstalled immediately above the hood.

For Non-Vented (recirculating) Installations

If it is not possible to vent cooking fumes and vapors to the

outside, the hood can be used in the non-vented (recirculating)

version, fitting a charcoal filter and the deflector. Fumes and

vapors are recycled through the top grille.

Roof Venting Wall Venting Non-vented

(recirculating)

A. Roof cap A. Wall cap A. Deflector

B. 8" (20.0 cm) B. 8" (20.0 cm) B. 8" (20.0 cm)

round vent round vent round vent

NOTE: Wall venting may not be possible for all installations.

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent Piece 8" (20.0 cm) Round

45° elbow 2.5 ft

(0.8 m)

90° elbow 5.0 ft

(1.5 m)

Maximum equivalent vent length is 35 ft (10.7 m).

Example vent system

90° e,bow _,_ 6tt (1._m)-_._l Wall cap

2fl

(0.6m)

The following example falls within the maximum recommended

vent length of 35 ft (10.7 m).

1 - 90 ° elbow = 5.0 ft (1.5 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Length of system = 13.0 ft (3.9 m)

E®c 'ccl <i!®quss> :Y.............@n'B

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSl/NFPA 70 (latest

edition), or CSA Standards C22.1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate.

The model/serial plate is located behind the filter on the rear

wall of the range hood.

Wire sizes must conform to the requirements of the National

Electrical Code, ANSl/NFPA 70 (latest edition), or CSA

Standards C22.1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

INSTALLATIONINSTRUCTIONS

• It is recommended that the vent system be installed before

hood is installed.

• Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

• Check your ceiling height and the hood height maximum

before you select your hood.

1. Disconnect power.

2. Determine which venting method to use: roof, wall, or non-

vented.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

5. Determine and mark the centerline on the wall where the

canopy hood will be installed.

6. Select a mounting height between a minimum of

24" (61.0 cm) for an electric cooking surface, a minimum of

27" (68.6 cm) for a gas cooking surface, and a suggested

maximum of 36" (91.4 cm) above the range to the bottom of

the hood and mark a reference line on the wall.

7. Tape template in place, aligning the template centerline and

bottom of template with hood bottom line and with the

centerline marked on the wall.

'<i ill...........................

,4.Centerline

B. Lower support bracket

C. 5 x 45 mm screws

D. Mounting height reference

E. Fastener locations

F Waft

Place the support bracket on the template aligning it with the

traced rectangle. Mark centers of 4 fastener locations through

the template to the wall, 2 for support bracket, 2 for bottom

rear of blower housing.

IMPORTANT: All screws must be installed into wood.

Remove the template.

Drill %4" (2.75 mm) pilot holes at all locations where screws

are being installed into wood.

NOTE: When mounting into a concrete wall, drill 5/le" (8 mm)

pilot holes and use anchors supplied.

10. Attach the support bracket to the wall using 2 - 5 x 45 mm

screws at the top 2 drilled hole locations.

A. Support bracket

B. 5 x 45 mm screws

C. Centerline on wall

Install vent cover bracket to wall about %" (3.0 mm) away

from the ceiling. Use 2 - 5 x 45 mm screws with 8 x 40 mm

drywall anchors supplied.

' B

A. Vent cover bracket

B. Centerline on wall

Complete Preparation

1. Determine and make all necessary cuts in the wall for the vent

system. Install the vent system before installing the hood. See

"Venting Requirements" section.

2. Determine the required height for the home power supply

cable and drill a 11¼'' (3.2 cm) hole at this location.

3. Run wire through the home power supply cable according to

the National Electrical Code or CSA Standards and local

codes and ordinances. There must be enough 1/2"conduit

and wires from the fused disconnect (or circuit breaker) box

to make the connection in the hood's electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

4. Use caulk to seal all openings.

Using 2 or more people, hang blower housing on lower

support bracket using the 2 mounting hooks on the rear of

the blower housing.

Vent Cover Bracket Assembly and Installation

1. Assemble the 3 pieces of the vent cover bracket using 4 -

4 x 8 mm screws provided. The assembled bracket should be

sized to dimension "X" to fit inside the upper vent cover.

A. Vent cover bracket assembly

B. Upper vent cover

C. 4 x 8 mm screws

A. Lower support bracket

B. Mounting hooks

C. Adjust in and out

(for leveling front to back).

D. Adjust up and down

(for leveling left to right).

E. Blower housing

Level the blower housing with leveling screws in mounting

hooks, using a level across bottom of blower housing.

3. Remove the metal grease filter and secure the blower

housing with two screws in the bottom holes located in the

rear of the blower.

A. Rearof blower housing

B.Bottom 5x 45 mm screw holes

Glass Mantle Installation

1. Place the glass mantle onto the hood.

2. Connect glass mantle to range hood with the 2 glass

mounting brackets and four 4 x 8 mm screws.

A. Glass mantle

B. Glass mounting bracket

C. 4 x 8 mm screws

Vented Installation Only

1. Fit vent system over transition piece.

2. Seal connection with clamps.

3. Check that backdraft dampers work properly.

For Non-vented (Recirculating) Installation:

1. Assemble the 3 parts of the deflector with 2 - 3.5 x 9.5 mm

screws provided. The assembled deflector should be sized to

fit the width of the vent cover bracket installed earlier.

A. Vent cover bracket width

B.Deflector

C. 3.5 x 9.5 mm screws

Connect the deflector to the vent cover bracket using 4 - 3.5

x 9.5 mm screws provided.

..........A

....s"

A. Vent cover bracket

B.3.5 x 9.5 mm screws

3. Measure the length of 8" (20.3 cm) round vent (not provided)

needed to connect the transition to the deflector.

NOTE: Vent should fit inside deflector a minimum of

1" (2.5 cm)

4. Install vent between the transition and the deflector.

5. Seal connection with clamps.

6. Check that backdraft dampers work properly.

Mc,, <®Eecff Connect on

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

Disconnect power•

Remove terminal box cover•

Remove the knockout in the terminal box cover and install a

UL listed or CSA approved 1/2"strain relief•

Run 3 wires, black, white and green (14AWG), in 1/2"conduit

from service panel to terminal box. Use caulking to seal

opening•

g .........................

A .......

C ............_!_--

E c

A. UL listed or CSA approved strain refief

B. Home power supply cable

C• Terminal box

D. Black wires

E• Green (or bare) wire connected to yellow-green wire

F. White wires

5. Use UL listed wire connectors and connect black wires (D)

together•

6. Use UL listed wire connectors and connect white wires (F)

together•

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

7. Connect green (or bare) ground wire from home power supply

to yellow-green ground wire (E)in terminal box using UL listed

wire connectors•

8. Tighten strain relief screw•

9. Install terminal box cover•

10. Check that all light bulbs are secure in their sockets•

11. Reconnect power•

Push lower cover down onto hood and lift upper cover to ceiling

and install with two 2.9 x 6.5 mm screws.

NOTE: For vented installations the upper vent cover may be

reversed to hide slots.

,_ ....................................................S

A. Vent cover bracket

B. Upper vent cover

C. Lower vent cover

D. 2.9 x 6.5 mm screws

1. For non-vented (recirculating installations) install charcoal

filter, wrapping it around the grease filter.

2. Place the charcoal filter mat around the grease filter and fix it

in place by using the cap lock springs provided.

3. Position the upper cap and fix it in place using the cap lock

spring provided.

A B

A. Charcoal filter mat

B. Grease filter

C. Charcoal filter side lock springs

D. Upper cap

E. Cap lock spring

F. Grease filter support

For all installations, install the grease filter. See "Range Hood

Care" section.

Check Range Hood Operation

If range hood does not operate, check to see whether a circuit

breaker has tripped or a household fuse has blown.

NOTE: To get the most efficient use from your new range hood,

read the "Range Hood Use" section.

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the

kitchen.

Control Panel

The range hood controls are located on the front side of the

canopy.

A B C D E

[r el

@ Clean grease filter I

A. Power decrease

B. Power increase

C.Display

D.Light

E. Timer

Grease Filter Saturation Alarm

After 30 hours of fan function, the display will show "Clean

Grease Filter" when the fan is active. When this icon shows in the

display, the installed grease filters should be washed. See

"Range Hood Care" section.

• To reset the grease filter saturation alarm, press and hold the

POWER INCREASE button for 5 seconds. The "Clean Grease

Filter" icon will no longer be displayed.

Charcoal Filter Saturation Alarm

After 120 hours of fan function, the display will show "Replace

Charcoal Filter" when the fan is active. When this icon shows in

the display, the charcoal filters should be replaced. See "Range

Hood Care" section.

• To reset the charcoal filter saturation alarm, press and hold

the POWER DECREASE button for 5 seconds. The "Replace

Charcoal Filter" icon will no longer be displayed.

Audible Signal Activation and Deactivation

The audible signals can be activated or deactivated by pressing

the "LIGHT" button for 5 seconds.

• If the audible signal is activated, a tone will sound, and "Snd"

will appear on the display for 3 seconds.

• If the audible signal is deactivated, "Snd" will appear on the

display for 3 seconds.

Charcoal Filter (Recirculation Accessory) Inclusion and

Exclusion

When the charcoal filter is in use (recirculating mode), press and

hold the POWER DECREASE and POWER INCREASE buttons at

the same time for 5 seconds. "Able" will appear on the display for

3 seconds.

If the charcoal filter is not used (vented mode), press and hold

the POWER DECREASE and POWER INCREASE buttons at the

same time for 5 seconds, "none" will appear on the display for

3 seconds.

• When the charcoal filter has been excluded, the charcoal filter

alarm is disabled.

• The inclusion or exclusion of the charcoal filter must be

selected while the lights and the fan motor are Off.

Heat Sensor

The control is equipped with a heat sensor that will turn on the

blower to the highest speed if excessive heat occurs around the

control area.

• If the blower is On or Off, the blower will automatically set to

the highest speed. "Auto" will appear in the display to

indicate that the heat sensor has detected excessive heat.

• When the blower is operating due to excessive heat detected

by the heat sensor, the blower speed cannot be decreased.

• When the temperature level on the hood drops to normal, the

blower will return to its setting before the excessive heat was

sensed.

The timer can be set from 1 to 60 minutes. The default timer

setting is 10 minutes.

To use the timer:

1. Press the Timer button to enter the timer mode. After

5 seconds the default time will be automatically selected.

2. Press the POWER DECREASE and POWER INCREASE

buttons while the display is flashing (5 seconds) to adjust to

the desired time. Pressing the timer button again or waiting

5 seconds after selecting the desired time will start the timer

countdown.

3. The timer can be canceled at any time by pressing the Timer

button again.

NOTE: During the timer setup, the Power Decrease and Power

Increase buttons are dedicated to the timer. After the timer starts,

the Power Decrease and Power Increase buttons can be used for

other functions.

Power Increase/On

This button is used to turn the fan On or increase the fan speed.

• The fan will turn On if the Power Increase button is pressed

and the hood was Off.

• An audible tone will sound when the fan reaches its highest

speed.

Power Decrease/Off

• This button is used to turn the fan Off or to decrease the fan

speed.

RANGE HOOD CARE

To operate the light:

1. Press the Light button to turn the light on to high.

2. Press the Light button again to turn the light to low.

3. Press the Light button a third time to turn the light off.

IMPORTANT: Clean the hood and grease filters frequently

according to the following instructions. Replace grease filters

before operating hood.

Be sure lights are cool before cleaning the hood.

Exterior Surfaces

Clean the range hood with a mild detergent and soft cloth. To

avoid damage to the exterior surface, do not use abrasive

cleanser or steel-wool pads.

Metal Grease Filters

The filters should be washed frequently. Place metal filters in

dishwasher or hot detergent solution to clean.

Let filter dry thoroughly before replacing it.

To Remove Metal Grease Filters

1. Turn off fan and lights. Check that halogen lamp is cool.

2. Remove the filter holder frame and grease filter using a flat-

blade screwdriver to turn the grease filter release screws 90°

counterclockwise.

_ ..............................................................................C

A. Grease filter release screw

B. Filter frame holder

C. Grease filter

To Replace Metal Grease Filter

1. Turn off fan and lights. Check that halogen lamp is cool.

2. Remove the filter holder frame and grease filter using a flat-

blade screwdriver to turn the grease filter release screws 90°

counterclockwise.

3. Replace grease filter and filter holder frame into range hood.

Align the grease filter release screw and use a flat-blade

screwdriver to turn the grease filter release screws 90°

clockwise to lock in place.

Charcoal Filters - For Non-Vented (recirculating)

Installations

NOTE: After approximately 3 years of use the charcoal filter

should be replaced. To order a replacement Charcoal Filter Kit,

see the "Assistance or Service" section.

The charcoal filters can be cleaned and reactivated. Clean the

filter in the dishwasher using normal detergent and choosing the

highest temperature setting.

To reactivate the filter, the filter should be dried in an oven for

10 minutes with a maximum temperature of 210°F (100°C).

To Replace Charcoal Filters

1. Turn fan and lights off. Check that halogen lamp is cool.

2. Remove the metal grease filters. See "Metal Grease Filters"

section.

3. Remove the upper and side lock springs.

4. Clean or discard the charcoal filter.

5. Install cleaned or replacement filter.

Replacing a Halogen Lamp

Turn off the range hood and allow the halogen lamp to cool. To

avoid damage or decreasing the life of the new bulb, do not

touch bulb with bare fingers. Replace bulb, using tissue or

wearing cotton gloves to handle bulb.

If new lights do not operate, make sure the lamps are inserted

correctly before calling service.

1. Disconnect power.

2. Use a flat-blade screwdriver and gently pry the light cover

loose.

3. Remove the lamp and replace with a 12-volt, 20-watt

maximum, halogen lamp made for a G-4 base.

4. Replace the light cover.

5. Reconnect power.

WIRING DIAGRAM

WIRINGBOX

L@N

ElectronicUserinterface

ElectronicPowerBoard

N L NL NM

P1 P2 P4A P3 P4

ATTENTION!:

ADDITIONALLAMPSONLY

PRESENTONTHEVERSIONS

WITH4 LAMPS

--I I-- --1 I--

, o, o, , o, o,,

1_e'r---m _ --- l

i ,. i y "_ y i

- - - r_e r ..... i

I--l

CON2 1

Y-G

CON1

$3 $2 $1

P8 P7 P6

LIJ oo.4

cc _

C13 rn

f," db "

ASSISTANCEOR SERVICE

When calling for assistance or service, please know the purchase

date and the complete model and serial number of your

appliance. This information will help us to better respond to your

request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance. To locate factory

specified replacement parts in your area, call us or your nearest

designated service center.

Call the dealer from whom your appliance was purchased, or call

Jenn-Air at 1-800-688-1100 to locate an authorized service

company. When calling, please know the purchase date and the

complete model and serial number of your appliance. Be sure to

retain proof of purchase to verify warranty status.

If the dealer or service company cannot resolve your problem,

write to:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Web address: www.jennair.com

Or call: 1-800-688-1100

U.S. customers using -I-I-Yfor deaf, hearing impaired or speech

impaired, call: 1-800-688-2080 (Monday - Friday, 8:00 a.m. -

8:00 p.m. Eastern Time).

NOTE: When writing or calling about a service problem, please

include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt).

User's guides, service manuals and parts information are

available from Jenn-Air Brand Home Appliances, Customer

eXperience Center.

Recirculation Kit

(for non-vented installations only)

Order Part Number W10272064

Replacement Charcoal Filters

(for non-vented installations only)

Order Part Number W10272069

Chimney Extension Kit

Order Part Number W10272071

Call the dealer from whom your appliance was purchased, or call

Jenn-Air at 1-800-807-6777 to locate an authorized service

company. When calling, please know the purchase date and the

complete model and serial number of your appliance. Be sure to

retain proof of purchase to verify warranty status.

If the dealer or service company cannot resolve your problem,

write to:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Web address: www.jennair.ca

Or call: 1-800-807-6777.

NOTE: When writing or calling about a service problem, please

include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt).

User's guides, service manuals and parts information are

available from Jenn-Air Brand Home Appliances, Customer

eXperience Centre.

JENN-AIR MAJOR APPLIANCEWARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Jenn-Air brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Jenn-Air") will pay for factory

specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Jenn-Air designated

service company. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used

in the country in which it was purchased. Outside the 50 United States and Canada, this limited warranty does not apply. Proof of

original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is

contrary to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by Jenn-Air.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Jenn-Air within 30 days from the date of purchase.

6. Any food loss due to refrigerator or freezer product failures.

7. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be

repaired in the home and only in-home service is covered by this warranty.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Jenn-Air servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with published installation instructions.

11. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty

is void if the factory applied serial number has been altered or removed from your major appliance.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. JENN-AIR SHALL NOT BE LIABLE FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

If outside the 50 United States and Canada, contact your authorized Jenn-Air dealer to determine if another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," you may find

additional help by checking the "Assistance or Service" section or by calling Jenn-Air. In the U.S.A., call 1-800-688-1100. In Canada,

call 1-800-807-6777. 9/07

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

SECURITEDELA HOTTEDECUISINIERE

Votre securite et celle des autres est tres importante.

Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de

toujours lire tousles messages de s_curit_ et de vous y conformer.

Voici le symbole d'alerte de s_curit&

Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves & vous

et &d'autres.

Tous les messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d_cbs ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d_cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tousles messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

llVIPORTANTES iNSTRUCTiONS DE SI CURITI

AVERTISSEMENT : POUR REDUIRE LE RISQUE

D'INCENDIE, CHOC ¢:LECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

m Utiliser cet appareil uniquement dans les applications

envisag6es par le fabricant. Pour toute question, contacter

le fabricant.

m Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre I'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour emp6cher tout r6tablissement accidentel de

I'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur le tableau

de disjoncteurs une 6tiquette d'avertissement pro6minente

interdisant le r6tablissement de I'alimentation.

m Tout travail d'installation ou c&blage 61ectrique doit 6tre

r6alis6 par une personne qualifi6e, dans le respect des

prescriptions de tousles codes et normes applicables, y

compris les codes du b&timent et de protection contre les

incendies.

m Une source d'air de d6bit suffisant est n6cessaire pour le

fonctionnement correct de tout appareil & gaz (combustion

et 6vacuation des gaz & combustion par la chemin6e), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de 1'6quipement de chauffage et

les prescriptions des normes de s6curit6 - comme celles

publi6es par la National Fire Protection Association (NFPA)

et I'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorit6s r6glementaires locales.

m Lors d'op6rations de d6coupage et de perqage dans un mur

ou un plafond, veiller & ne pas endommager les c&blages

61ectriques ou canalisations qui peuvent s'y trouver.

m Les ventilateurs d'6vacuation doivent toujours d6charger

I'air & I'ext6rieur.

MISE EN GARDE : Cet appareil est con£:u uniquement

pour la ventilation g6n6rale. Ne pas I'utiliser pour I'extraction

de mati_res ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et 6vacuer ad6quatement les gaz, veiller &acheminer I'air

aspir6 par un conduit jusqu'b, I'ext6rieur - ne pas d6charger

I'air aspir6 dans un espace vide du b&timent comme une

cavit6 murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR R¢:DUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

MI2TALLIQUES.

AVERTISSEMENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINIF:RE :

[] Ne jamais laisser un 616ment de surface fonctionner &

puissance de chauffage maximale sans surveillance. Un

renversement/d6bordement de mati_re graisseuse pourrait

provoquer une inflammation et la g6n6ration de fum6e.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

[] Veiller & toujours faire fonctionner le ventilateur de la hotte

Iors de la cuisson avec une puissance de chauffage 61ev6e

ou Iors de la cuisson d'un mets &flamber (& savoir cr6pes

Suzette, cerise jubil6e, steak au poivre flamb6).

[] Nettoyer fr6quemment les ventilateurs d'extraction. Veiller &

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

[] Utiliser toujours un ustensile de taille appropri6e. Utiliser

toujours un ustensile adapt6 & la taille de 1'616ment

chauffant.

AVERTISSEMENT : POUR RC:DUIRE LE RISQUE DE

DOMMAGES CORPORELS APRF:S LE DECLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINI_:RE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :a

[] Placer sur le r6cipient un couvercle bien ajust6, une t61e &

biscuits ou un plateau m6tallique POUR ETOUFFER LES

FLAMMES, puis 6teindre le brt_leur. VEILLER ,_ ¢:VITER

LES BRULURES. Si les flammes ne s'6teignent pas

imm6diatement, ¢:VACUER LA PIECE ET APPELER LES

POMPIERS.

[] NE JAMAIS PRENDRE EN MAIN UN RECIPIENT

ENFLAMME - vous risquez de vous brQler.

[] NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brQlante.

[] Utiliser un extincteur SEULEMENT si :

- II s'agit d'un extincteur de classe ABC, dont on connaft le

fonctionnement.

- II s'agit d'un petit feu encore limit6 & I'endroit oQ il s'est

d6clar6.

- Les pompiers ont 6t6 contact6s.

- II est possible de garder le dos orient6 vers une sortie

pendant I'op6ration de lutte contre le feu.

aRecommandations tir6es des conseils de s6curit6 en cas

d'incendie de cuisine publi6s par la NFPA.

[] AVERTISSEMENT : Pour r6duire le risque d'incendie

ou de choc 61ectrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de r6glage de la vitesse & semi-

conducteurs.

LIRE ET CONSERVER CES iNSTRUCTiONS

EXIGENCESD'INSTALLATION

Rassembler tous les outils et pieces necessaires avant

d'entreprendre I'installation. Lire et observer les instructions

fournies avec chaque outil de la liste suivante.

Outils n_cessaires

• Niveau

• Perceuse avec forets de 11¼'' (3,0 cm), 3/8"(9,5 mm),

7/64"(2,75 mm) et 1/8"(3,0 mm)

• Crayon

• Pince & denuder ou couteau utilitaire

• Metre-ruban ou regle

• Pince

• Pistolet & calfeutrage et compose de calfeutrage resistant

aux intemperies

• Brides de serrage pour conduit d'evacuation

• Scie sauteuse ou scie & guichet

• Tournevis & lame plate

• Cisaille de ferblantier

• Tournevis Phillips

Pi_ces n_cessaires

• C&ble d'alimentation electrique de la residence

• Serre-c&ble de V2"(12,7 mm) (homologation UL ou CSA)

• 3 connecteurs de ills (homologation UL)

Pour une installation avec d_charge a I'ext_rieur - Materiel

additionnel n_cessaire :

• 1 bouche de decharge (decharge &travers le mur ou &travers

le toit (mitre)

• Circuit d'evacuation (conduits metalliques)

Pour une installation sans d_charge a I'ext_rieur (recyclage) -

Materiel additionnel n_cessaire :

• Trousse de recyclage (produit n° W10272064) - seulement

pour une installation sans decharge a I'exterieur (recyclage).

Voir la section "Assistance ou service" pour commander.

Pi_ces fournies

Retirer les pieces des emballages. Verifier que toutes les pieces

sont presentes.

• Auvent de hotte avec ventilateur et lampes installes

• 2 crochets de montage en verre

• Raccord de transition avec clapet anti-reflux installe

• Tablette en verre

• Bride de support du cache-conduit (3 pieces)

• Gabarit de montage

• Cache-conduit (2 pieces)

• 2-vis2,9x6,5mm

• 8-vis4x8mm

• 6-vis5x45mm

• 2 chevilles d'ancrage mural de 8 x 40 mm

• 4 chevilles d'ancrage mural de 10 x 50 mm

IMPORTANT : Observer les dispositions de tousles codes et

reglements en vigueur.

Confier I'installation de la hotte & un technicien qualifi& C'est &

I'installateur qu'incombe la responsabilite de respecter les

distances de separation exigees, specifiees sur la plaque

signaletique de I'appareil. La plaque signaletique de I'appareil est

situee derriere le filtre de gauche, sur la paroi arriere de la hotte.

On doit toujours installer la hotte & distance des sources de

courant d'air (fen_tres, portes et bouches de chauffage).

Respecter les dimensions indiquees pour les ouvertures &

decouper dans les placards; ces dimensions tiennent compte

des valeurs minimales des degagements de separation.

On doit disposer d'une prise de courant electrique reliee & la

terre. Voir la section "Specifications des circuits electriques".

La hotte est configuree & I'usine pour la decharge & travers le toit

ou un mur. Pour une installation sans decharge & I'exterieur

(recyclage), voir "Installations sans decharge & I'exterieur

(recyclage)", & la section "Raccordement du circuit

d'evacuation".

La trousse de recyclage (piece n° W10272064) est disponible

chez votre marchand ou chez un distributeur de pieces agree.

On doit assurer I'etancheite au niveau de chaque ouverture

decoupee dans le plafond ou un mur traverse par I'equipement

de la hotte.

Installation dans une r_sidence mobile

L'installation de cette hotte doit satisfaire aux exigences de la

norme Manufactured Home Construction Safety Standards, Titre

24 CFR, partie 328 (anciennement Federal Standard for Mobile

Home Construction and Safety, titre 24, HUD, partie 280); Iorsque

cette norme n'est pas applicable, I'installation doit satisfaire aux

criteres de la plus recente edition de la norme Manufactured

Home Installation 1982 (Manufactured Home Sites, Communities

and Setups)ANSI A225.1/NFPA 501A, ou des codes et

reglements Iocaux applicables.

• Dispositif de support du ventilateur

La page charge ...

Jenn-Air JXW5036WS Le manuel du propriétaire

Marque: Jenn-Air

Modèle: JXW5036WS

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Jenn-Air JXW5036WS Owner's manual

Jenn-Air JXW5036WS Le manuel du propriétaire

Ce manuel convient également à

Jenn-Air JXW5036WS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents