Chief LSB101 Guide d'installation

Chief
Marque
Chief
Modèle
LSB101
Catégorie
Mur
Taper
Guide d'installation

Vous trouverez ci-dessous de brèves informations pour Support de décalage latéral LSB101. Ce support offre un décalage latéral jusqu'à 3 pouces pour les projecteurs, et il est utilisé avec le support de projecteur Chief Listed RPM Series. Il peut être utilisé pour un décalage latéral ou un décalage avant/arrière. Le poids combiné de tous les composants attachés au LSB101 ne doit pas dépasser 22,68 kg. La capacité de poids du LSB101 peut être limitée à la capacité de poids la plus faible de tout autre composant ou accessoire utilisé dans le système de montage.

Vous trouverez ci-dessous de brèves informations pour Support de décalage latéral LSB101. Ce support offre un décalage latéral jusqu'à 3 pouces pour les projecteurs, et il est utilisé avec le support de projecteur Chief Listed RPM Series. Il peut être utilisé pour un décalage latéral ou un décalage avant/arrière. Le poids combiné de tous les composants attachés au LSB101 ne doit pas dépasser 22,68 kg. La capacité de poids du LSB101 peut être limitée à la capacité de poids la plus faible de tout autre composant ou accessoire utilisé dans le système de montage.

INSTALLATION INSTRUCTIONS
Lateral Shift Bracket Accessory
LSB101
LSB101 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the LSB101 does not exceed 50 lbs
(22.68 kg)
•The weight capacity of the LSB101 may be LIMITED to
the lowest weight capacity of any other component or
accessory used within the mounting system.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : The LSB101 is designed to provide up to 3"
lateral shift for projectors, and is used with the Chief Listed
RPM Series projector mount.
--SAVE THESE INSTRUCTIONS--
Installation Instructions LSB101
3
DIMENSIONS
LEGEND
DIMENSIONS: [MILLIMETERS]
INCHES
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
LSB101 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
5/32" - security
(included)
A (1)
[LSB101 bracket]
B (1)
[LSB101 bracket]
C (2)
10-32 x 1" D (2)
10-32 x 1" E (2)
8-32 x 3/8"
F (2)
[Thumb nut]
G (1)
5/32"
(security)
.
Installation Instructions LSB101
5
ASSEMBLY AND INSTALLATION
The LSB101 may be used in either a lateral shift application or
a forward/backward shift application.
NOTE: For a lateral shift application, proceed to Attaching
LSB101 - Lateral Shift.
Attaching LSB101 - Forward/Backward Shift
1. Attach one thumb nut (F) with one 8-32 x 3/8" button head
security cap screw (E) to both LSB101 brackets (A and B).
(See Figure 1)
Figure 1
2. Proceed to Attaching LSB101 - Lateral Shift section.
Attaching LSB101 - Lateral Shift
1. Line up keyhole slots of both LSB-101 brackets (A and B)
with SLM interface bracket (not included). (See Figure 2)
Figure 2
2. Slide LSB101 brackets so that thumb nuts on SLM interface
bracket rest in the narrow end of key slots. (See Figure 3)
Figure 3
3. Shut bracket arms.
4. Secure bracket arms with one 10-32 x 1" Phillips machine
screw (C) on outside of each LSB101 bracket. (See Figure
4)
NOTE: 10-32 x 1" button head security screws (D) may be
used in place of the Phillips machine screws (C).
Figure 4
(E) x 2
1
(F) x 2
(A)
(B)
SLM
interface bracket
2
2
3
4
(C) x 2
LSB101 Installation Instructions
6
Attaching RPMA (not included) to LSB101
1. Ensure that lock lever on RPMA is moved to "Unlocked"
position.
2. Slide RPMA onto LSB101 brackets (A and B).(See Figure 5)
3. Move the lock lever to "Locked" position and turn key to
lock.
Figure 5
Shifting RPMA on LSB101 Bracket
1. Loosen two Phillips screws on each LSB101 bracket (A and
B). (See Figure 6)
2. Shift RPMA left to right as needed.
NOTE: If using the LSB101 bracket in a forward/backward
application, shift the RPMA either backward or forward
as needed.
3. TIghten the Phillips screws as needed. (See Figure 6)
Figure 6
2
3
Insert key
and turn
to lock
Lock Lever
("Locked" position)
3
13
2
x 4
Installation Instructions LSB101
7
LSB101 Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002530 Rev00
2014 Milestone AV Technologies
www.chiefmfg.com
03/14
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief LSB101 Guide d'installation

Chief
Marque
Chief
Modèle
LSB101
Catégorie
Mur
Taper
Guide d'installation

Vous trouverez ci-dessous de brèves informations pour Support de décalage latéral LSB101. Ce support offre un décalage latéral jusqu'à 3 pouces pour les projecteurs, et il est utilisé avec le support de projecteur Chief Listed RPM Series. Il peut être utilisé pour un décalage latéral ou un décalage avant/arrière. Le poids combiné de tous les composants attachés au LSB101 ne doit pas dépasser 22,68 kg. La capacité de poids du LSB101 peut être limitée à la capacité de poids la plus faible de tout autre composant ou accessoire utilisé dans le système de montage.

Télécharger le PDF
rapport

dans d''autres langues

Documents connexes