Kärcher K3 49M Mode d'emploi

English 2

Français 18

Español 35

K 3.49 M

59629130 06/09

HIGH PRESSURE WASHER - OPERATOR MANUAL

NETTOYEUR HAUTE PRESSION - MANUEL D'UTILISATION

MANUAL DE USUARIO DEL LIMPIADOR DE ALTA PRESIÓN

2 English

To register this product, please visit:

www.karcher-register.com

For technical support, go to:

www.karcher-help.com

If you purchased this unit new and parts

are missing, or if you need to file a war-

ranty claim, please call:

1-800-537-4129

You will need to fax or email your re-

ceipt to a customer service agent. All

other information can be found at:

www.karcherresidential.com

Call: 01-800-024-13-13 for help or visit

our website: www.karcher.com.mx

DANGER

indicates “an imminently hazardous sit-

uation which, if not avoided, will result in

death or serious injury.”

WARNING

indicates “a potentially hazardous situa-

tion which, if not avoided, could result in

death or injury.”

CAUTION

indicates “a potentially hazardous situa-

tion which, if not avoided, may result in

minor or moderate injury or in property

damage incidents.”

The owner and/or user must have an

understanding of the manufacturer’s

operating instructions and warnings be-

fore using this pressure washer.

Warning information should be empha-

sized and understood.

If the operator is not fluent in English,

the manufacturer’s instructions and

warnings shall be read to and discussed

with the operator in the operator’s native

language by the purchaser/owner, mak-

ing sure that the operator comprehends

its contents.

Owner and/or user must study and

maintain for future reference the manu-

facturers’ instructions.

HIGH PRESSURE WASHER OPERATOR MANUAL

MODEL OVERVIEW 3

IMPORTANT SAFETY INSTRUC-

TIONS

4 - 5

ASSEMBLY INSTRUCTIONS 6

OPERATING INSTRUCTIONS 6 - 7

USING THE ACCESSORIES 8

WORKING WITH DETERGENTS 8 - 9

TAKING A BREAK 9

SHUTTING DOWN & CLEAN-UP 10

WINTERIZING AND LONG-TERM

STORAGE

11

CARE AND MAINTENANCE

INSTRUCTIONS

11

CLEANING TIPS 12 - 13

OPTIONAL CLEANING ACCES-

SORIES

14 - 15

TROUBLESHOOTING 16 - 17

Specifications

Max. Pressure 1800 PSI

Max. Water Flow 1.5 GPM

Amp draw 13 AMPS

Voltage 120 V

Part No. 1.601-730.0

Serial no.

Customer Support

USA and Canada

Customer Support

Mexico

Safety Alert Symbols

Owner/User Responsibility

English 3

1 Power cord with Ground Fault Circuit

Interrupter (GFCI)

2 Trigger gun

3 Trigger gun safety lock

4 High pressure hose

5 Water inlet with garden hose con-

nector

6 Transport handle

7 Accessory storage

8 Detergent tank (removeable)

9 Trigger gun storage

10 Detergent suction tube with filter

11 High pressure outlet

12 ON/OFF switch

13 Vario Power Spray wand

14 Dirtblaster® (Rotary spray wand)

CAUTION

This unit has been designed for use with

cleaning detergents recommended by

the manufacturer. The use of other

cleaning detergents may affect the op-

eration of the machine and void the war-

ranty.

For household use only!

MODEL OVERVIEW

4 English

WARNING!

When using this product basic

precautions should always be

followed, including the following:

Read all the instructions before us-

ing the product.

To reduce the risk of injury, close su-

pervision is necessary when a prod-

uct is used near children.

Know how to stop the product and

bleed pressures quickly. Be thor-

oughly familiar with the controls.

Stay alert – watch what you are do-

ing.

Do not operate the product when fa-

tigued or under the influence of alco-

hol or drugs.

Keep operating area clear of all per-

sons.

Do not overreach or stand on unsta-

ble support. Keep good footing and

balance at all times.

Follow the maintenance instructions

specified in the manual.

This Product Is Provided With A

Ground Fault Circuit Interrupter Built

Into The Power Cord Plug. If Re-

placement Of The Plug Or Cord Is

Needed, Use Only Identical Re-

placement Parts.

Risk of Injection or Injury – Do Not

Direct Discharge Stream At Per-

sons.

High pressure jets can be dangerous

if misused. The jet must not be di-

rected at persons, animals, electrical

devices, or the machine itself.

Wear safety goggles.

Do not use acids and solvents in this

product. These products can cause

physical injuries to the operator and

irreversible damage to the machine.

To reduce the risk of electrocution,

keep all connections dry and off the

ground. Do not touch plug with wet

hands.

The Trigger Gun Safety Lock PRE-

VENTS the trigger from accidentally

being engaged. This safety feature

DOES NOT lock trigger in the ON

position.

Do not use extension cord with this

unit.

WARNING

Do not spray electrical apparatus and

wiring.

Do not use with flammable liquids and

toxic chemicals.

Injection hazard: equipment can cause

serious injury if the spray penetrates the

skin. do not point the gun at anyone or

any part of the body. In case of penetra-

tion seek medical aid immediately.

This system is capable of producing

12400 kPa /1800 PSI to avoid rupture

and injury, do not operate this pump

with components rated less than

12400 kPa /1800 PSI working pressure

(including but not limited to spray guns,

hose and hose connections).

Before servicing, cleaning or removing

any parts, shut off power and relieve

pressure.

IMPORTANT SAFETY INSTRUCTIONS

English 5

This product must be grounded. If it

should malfunction or breakdown,

grounding provides a path of least resis-

tance for electric current to reduce the

risk of electric shock. This product is

equipped with a cord having an equip-

ment-grounding conductor and a

grounding plug. The plug must be

plugged into an appropriate outlet that is

properly installed and grounded in ac-

cordance with all local codes and ordi-

nances.

DANGER

Improper connection of the equipment-

grounding conductor can result in a risk

of electrocution. Check with a qualified

electrician or service personnel if you

are in doubt as to whether the outlet is

properly grounded. Do not modify the

plug provided with the product - if it will

not fit the outlet, have a proper outlet in-

stalled by a qualified electrician. Do not

use any type of adapter with this prod-

uct.

This product is supplied with a Ground

Fault Circuit Interrupter (GFCI) built into

the power cord plug. This device pro-

vides additional protection from the risk

of electric shock. If power is interrupted

in the line, the GFCI will automatically

re-close the circuit to the load after pow-

er is restored. Depending on the GFCI

model, it may be necessary to manually

operate the reset button to restore pow-

er to the GFCI load circuit. If replace-

ment of the plug or cord is needed use

identical replacement parts.

CAUTION

When connecting the water inlet to the

water supply mains, local regulations of

your water company must be observed.

In some areas the unit must not be con-

nected directly to the public drinking wa-

ter supply. This is to ensure that there is

no feedback of chemicals into the water

supply. Direct connection via a receiver

tank or backflow preventer, for example,

is permitted.

Dirt in the feed water will damage the

unit. To avoid this risk, we recommend

fitting a water filter.

Garden hose must be at least 1/2

inch or 5/8 inch in diameter.

Flow rate of water supply must not

fall below 2 GPM (gallons per

minute).

Flow rate can be determined by run-

ning the water for one minute into an

empty 5-gallon container.

The water supply temperature must

not exceed 104°F/40°C.

Never use the pressure washer to

draw in water contaminated with sol-

vents, e.g. paint thinners, gasoline,

oil, etc.

Always prevent debris from being

drawn into the unit by using a clean

water source.

SAVE THESE

INSTRUCTIONS !

GROUNDING INSTRUCTIONS

GROUND FAULT CIRCUIT IN-

TERRUPTER PROTECTION

WATER SUPPLY

(Cold Water Only)

6 English

APhilips Screwdriver, medium size

(not supplied)

for final assembly

ÎSTEP 1:

ÎSTEP 2:

ÎSTEP 3:

ÎSTEP 4:

ÎSTEP 5:

ÎSTEP 6:

ÎSTEP 1:

Connect the high pressure hose to

the unit’s high pressure outlet.

ASSEMBLY INSTRUCTIONS

Required tools

OPERATING INSTRUCTIONS

English 7

ÎSTEP 2:

Insert the spray wand of your choice

into the trigger gun. Press in against

the spring tension and twist into

locked position.

ÎSTEP 3:

Connect garden hose to unit’s water

inlet.

ÎSTEP 4:

Connect garden hose to the cold wa-

ter source and turn water on com-

pletely.

ÎSTEP 5:

Plug the Ground Fault Circuit Inter-

rupter (GFCI) into a receptacle.

Press RESET button, indicator

should be “ON”.

Press TEST button, indicator should

be “OFF”.

Press RESET button for use.

WARNING

Do not use if above test fails.

ÎSTEP 6:

Unlock the trigger gun safety lock.

Trigger the gun to eliminate trapped

air, wait for a steady flow of water to

emerge from the spray nozzle.

ÎSTEP 7:

Turn on the high pressure washer (I/

ON).

The motor starts only if the trigger

of the gun is pulled and shuts off

when the trigger is released.

8 English

WARNING

To avoid serious injury never point

spray nozzle at yourself, other per-

sons or animals.

Always test an inconspicuous area

before cleaning with high pressure.

The Vario Power Spray Wand allows

you to adjust the cleaning pressure.

ÎTo clean at maximum pressure, the

wand must be positioned to the high

pressure setting (Max).

ÎFor lower pressure turn the wand

collar in the minus (Min) direction.

ÎTo apply detergent, the wand must

be positioned to the lower pressure

setting (Mix).

This nozzle features a 0º pencil jet

which rotates 360º for maximum dirt

cutting action, effectively increasing

cleaning performance up to 50%.

This nozzle combines the cleaning

performance of a 0º pencil jet with

the surface coverage of a wide angle

nozzle.

Not recommended for soft materi-

als, siding, painted surfaces,

decks or autos.

Always test an inconspicuous area

before cleaning with the Dirtblaster®.

Detergents can only be applied at

low pressure setting (Mix).

ÎSTEP 1:

Install the Vario Power Spray Wand.

Set the spray wand to the low pres-

sure setting (Mix).

ÎSTEP 2:

Fill the Detergent Tank with the se-

lected detergent.

USING THE ACCESSORIES

Vario Power Spray Wand

Dirtblaster®

WORKING WITH DETERGENTS

English 9

ÎSTEP 3:

Turn on the pressure washer (I). Pull

trigger to operate unit. Liquid deter-

gent is drawn into the unit and mixed

with water. Apply detergent to work

area. Do not allow detergent to dry

on surface.

ÎSTEP 4:

To rinse, move the VPS out of „Mix“

position and pull trigger to operate

unit.

ÎSTEP 5:

Cleaning up: Always draw fresh wa-

ter through the detergent tank or si-

phon tube when done to flush any

remaining detergents from the injec-

tion system.

For best results see Cleaning Tips

for specific information on how to

clean different surfaces.

Always Use Kärcher® Detergent for

Best Results

Kärcher® biodegradable detergents are

specially formulated to protect the envi-

ronment and your pressure washer. The

special formula won’t clog the suction

tube filter and will protect the internal

parts of the pressure washer for a long-

er life. For Kärcher® Detergents, check

your retailer or visit our website:

www.soappac.com

CAUTION

Never use:

– Bleach, Chlorine products and other

corrosive chemicals

– Liquids containing solvents (i.e.,

paint thinners, gasoline, oils)

– Tri-sodium phosphate products

– Ammonia products

– Acid-based products

These chemicals will harm the unit and

will damage the surface being cleaned.

Use of these items will void the war-

ranty.

ÎSTEP 1:

Release trigger and engage gun

safety lock.

ÎSTEP 2:

Turn pressure washer to OFF (0) po-

sition.

TAKING A BREAK ..five minutes or more

10 English

ÎSTEP 1:

Turn the switch to OFF (0) position

and unplug cord from outlet.

ÎSTEP 2:

Turn off the water source.

ÎSTEP 3:

Press trigger to release water pres-

sure.

ÎSTEP 4:

Disconnect the garden hose from

the water inlet on the unit.

ÎSTEP 5:

Disconnect the high pressure hose

from the high pressure outlet.

ÎSTEP 6:

Release trigger and engage gun

safety lock.

SHUTTING DOWN & CLEAN-UP

English 11

Î1: Disconnect all water connections.

Î2: Turn on the machine for a few

seconds, until the water which had

remained in the pump exits, turn off

immediately.

Î3: Do not allow high pressure hose

to become kinked.

Î4: Store the machine and accesso-

ries in a room which does not reach

freezing temperatures. DO NOT

store near furnace or other sources

of heat as it may dry out the pump

seals.

CAUTION

Failure to follow the above directions

will result in damage to the pump as-

sembly and accessories and will void

the warranty.

Kärcher® also recommends the regular

practice of using a pump protector like

“Kärcher® Pump Guard” to prevent cold

weather damage during storage in the

winter months.

ÎSTEP 1:

Pull out washer from the water inlet.

ÎSTEP 2:

Pull out water inlet filter with flat-

nose pliers.

ÎSTEP 3:

Rinse out water inlet filter in warm

water.

ÎSTEP 4:

Reinsert water inlet filter and washer

into the water inlet.

The unit is maintenance-free.

WINTERIZING AND LONG-TERM STORAGE

CARE AND MAINTENANCE INSTRUCTIONS

Cleaning the water inlet filter

Maintenance

12 English

CAUTION

Before cleaning any surface an in-

conspicuous area should be cleaned

to test spray pattern and distance for

maximum cleaning results.

If painted surfaces are peeling or

chipping, use extreme caution as

pressure washer may remove the

loose paint from the surface.

When using on surfaces which might

come in contact with food, flush sur-

faces with plenty of drinking water.

For additional cleaning tips and a

complete video library, visit our web-

site:

www.karcherresidential.com

(with or without detergent). Pre-rinse

deck and surrounding area with fresh

water. If using detergent, apply to sur-

face at low pressure. For best results,

limit your work area to smaller sections

of approximately 25 square feet. Allow

detergent to remain on surface 1-3 min-

utes. Do not allow detergent to dry on

surface. Rinse at high pressure in a long

sweeping motion keeping the spray

nozzle approximately 3-6 inches from

the cleaning surface. Always clean from

top to bottom and from left to right.

When moving on to a new section of the

cleaning surface, be sure to overlap the

previous section to eliminate stop marks

and ensure a more even cleaning result.

(with or without detergent). Pre-rinse

cleaning surface with fresh water. If us-

ing detergent, apply to surface at low

pressure (for best results, limit your

work area to sections of approximately

6 feet and always apply detergent from

bottom to top). Allow detergent to re-

main on surface 1-3 minutes. Do not al-

low detergent to dry on surface, if

surface appears to be drying, simply

wet down surface with fresh water. If

needed, use special wash brush attach-

ment (not included) to remove stubborn

dirt. Rinse at high pressure from top to

bottom in an even sweeping motion

keeping the spray nozzle approximately

6 inches from the cleaning surface.

(with or without detergent). Pre-rinse

cleaning surface with fresh water. If us-

ing detergent or Degreaser, apply to

surface at low pressure. For best re-

sults, limit your work area to smaller

sections of approximately 25 square

feet. Allow detergent or Degreaser to re-

main on surface 1-3 minutes. Do not al-

low detergent to dry on surface. Rinse

at high pressure in a sweeping motion

keeping the spray nozzle approximately

3-6 inches from the cleaning surface.

Always clean from top to bottom and

from left to right. For removing extreme-

ly stubborn stains, use the Dirtblaster®

Nozzle.

(with or without detergent). Pre-rinse

vehicle with fresh water. If using deter-

gent, apply to surface at low pressure.

For best results, clean one side of vehi-

cle at a time and always apply detergent

from bottom to top, do not allow deter-

gent to dry on surface. If needed, use

special wash brush attachment (not in-

cluded) to remove stubborn dirt. Rinse

at high pressure in a sweeping motion

CLEANING TIPS

Deck Cleaning

House Siding

Cement Patios, Brick and Stone

Cars, Boats & Motorcycles

English 13

keeping the spray nozzle approximately

6-8 inches from the cleaning surface

(distance should increase when rinsing

pin-striping or other sensitive surfaces).

Always clean from top to bottom and

from left to right. For best results, wipe

surface dry with a chamois or soft dry

cloth.

(with or without detergent). Pre-rinse

cleaning surface with fresh water. If us-

ing detergent or Degreaser, apply deter-

gent at low pressure. Allow detergent to

remain on surface 1-3 minutes. Do not

allow detergent to dry on surface. Rinse

at high pressure keeping the spray noz-

zle approximately 3-6 inches from the

cleaning surface. For removing ex-

tremely stubborn dirt, it may be neces-

sary to move the spray nozzle even

closer to the surface for greater dirt cut-

ting action.

(with or without detergent). Pre-rinse

furniture and surrounding area with

fresh water. If using detergent, apply to

surface at low pressure. Allow detergent

to remain on surface 1-3 minutes. Do

not allow detergent to dry on surface. If

needed use special Wash Brush Attach-

ment (not included) to remove stubborn

dirt. Rinse at high pressure in a sweep-

ing motion keeping the spray nozzle ap-

proximately 3-6 inches from the

cleaning surface. For best results, clean

from top to bottom and from left to right.

Barbecue Grills, Outdoor Power

Equipment & Gardening Tools

Patio & Lawn Furniture

14 English

Optional accessories are available to

further enhance your cleaning capabili-

ties. These accessories are accurate as

of the printing date of this manual.

Please check our website for pricing

and up-to-date information.

Specially formulated to protect your

pressure washer from freezing, corro-

sion and premature wear. The Pump

Guard also adds lubrication to valves

and seals to prevent sticking. Highly

recommended for all Kärcher® pressure

washers!

Part No. 9.558-998.0

Replacement hose fits Kärcher® pres-

sure washer with screw-on type gun

connections from 2400 PSI to

2500 PSI, Extension Hose for all

Kärcher® high pressure washers be-

tween the original equipment hose and

machine up to 2500 PSI.

Part No. 2.640-850.0

Need to clean second story windows or

other high areas? Increase the reach of

your pressure washer by up to 66" with

this extension kit. Includes 4 aluminum

sections for variable length. 66" fully as-

sembled. Fits most Kärcher® pressure

washers up to 2300 PSI. (bayonet)

Part No. 2.640-746.0

For more effortless cleaning of all

smooth surfaces (painted, glass and

plastic) try the Kärcher® Rotating Wash

Brush. Use it on your automobile, house

siding or windows. The water pressure

from your pressure washer causes the

inner brushes to gently spin, making

your cleaning job much easier. The an-

gle of brush head is adjustable to help

you reach difficult areas. Excellent for

the application of detergent. A must-

have accessory designed for Kärcher®

pressure washers up to 2300 PSI. (bay-

onet)

Part No. 2.640-743.0

Made with soft bristles that will not harm

painted surfaces. Easily attaches direct-

ly to the trigger gun. Ideal for stubborn

dirt on cars, boats, patio furniture and

other surfaces. Great for applying deter-

gent. Fits most Kärcher® pressure

washers up to 2300 PSI. (bayonet)

Part No. 2.640-740.0

Need to clean blocked pipes, drains or

downspouts? The Kärcher® pipe clean-

ing kit is the answer! The pipe cleaner

propels itself forward while simulta-

neously flushing out debris. For exam-

ple, insert the cleaning nozzle in the

base of a downspout, pull the trigger on

the pressure washer gun and watch as

the nozzle shoots out leaves and other

debris while climbing upward. Connects

directly to the trigger gun of most

Kärcher® pressure washers up to

2300 PSI. (bayonet)

Part No. 2.640-747.0

OPTIONAL CLEANING ACCESSORIES

Pump Guard

25 Ft. Extension /Replacement

High-Pressure Hose

66" Extension Wand (Four piece)

Rotating Wash Brush (bayonet)

Soft Clean Washing Brush

25 ft. Pipe Cleaning Kit (bayonet)

English 15

Why spend hours stripping old paint and

rust by hand using harsh chemicals?

Let the Kärcher® Wet Sandblasting Kit

do the work! Attach the kit to your pres-

sure washer, add abrasive material and

attack the rust and paint with our eco-

friendly alternative. Fits most Kärcher®

pressure washers up to 2300 PSI. (bay-

onet)

Part No. 2.638-792.0

Ideal for applications which require a

thick foam. Simply fill the resevoir cup

with liquid pressure washer detergent to

generate a foam spray. Connects di-

rectly to the trigger gun. Fits most

Kärcher® pressure washers up to

2300 PSI. (bayonet)

Part No. 6.964-507.0

For cleaning surfaces such as patios,

terraces and driveways without splash-

back, there is no better solution than the

Kärcher® T 100. It saves time by clean-

ing a one foot wide area gently as it hov-

ers, providing consistent, streak-free

cleaning. When you finish cleaning the

patio and driveway, remove the wand

and use the handle to clean garage

doors and other vertical surfaces. In-

cludes two nozzles which spin at high

speed for optimum results. Our top sell-

ing accessory for Kärcher® pressure

washers up to 2300 PSI. (bayonet)

Part No. 2.640-959.0

Wet Sandblasting Kit (bayonet)

Detergent Foamer Attachment

T 100 Wide Area Surface Cleaner

16 English

CAUTION Disconnect the machine from the power

source before making any repair.

TROUBLESHOOTING

Symptom Cause Solution

Motor will not start On/Off switch is in the “OFF”

(0) position.

Turn switch to the “ON” (I) posi-

tion

Power cord is not plugged in. Plug in power cord.

Electrical outlet does not sup-

ply adequate power.

Try a different outlet.

Tripped GFCI plug. Press “RESET” button on GFCI

plug.

Tripped circuit breaker. Switch off pressure washer.

The reset comes automatically

once the temperature of the

unit drops.

Unit does not

reach high pres-

sure.

Diameter of garden hose is

too small.

Replace with a 5/8 inch or larg-

er garden hose.

Water supply is restricted. Check garden hose for kinks,

leaks and blockage.

Not enough inlet water sup-

ply.

Open water source full force.

Water inlet filter is clogged. Remove filter and rinse out in

warm water.

Spray wand is on low pres-

sure position.

Turn spray wand to high pres-

sure position.

Output pressure

varies high and

low.

Not enough inlet water sup-

ply.

Turn water on full force. Check

garden hose for kinks, leaks or

blockage.

Pump is sucking air. Check that hoses and fittings

are air tight. Turn off machine

and purge pump by squeezing

trigger gun until a steady flow of

water emerges through the

nozzle.

Water inlet filter is clogged. Remove filter and rinse out in

warm water.

Discharge nozzle is obstruct-

ed.

Blow out or remove debris with

a fine needle.

Calcified gun, hose or spray

wand.

Run distilled vinegar through

detergent suction tube.

English 17

To register this product, please visit:

www.karcher-register.com

For technical support, go to:

www.karcher-help.com

If you purchased this unit new and parts

are missing, or if you need to file a war-

ranty claim, please call:

1-800-537-4129

You will need to fax or email your re-

ceipt to a customer service agent. All

other information can be found at:

www.karcherresidential.com

Call: 01-800-024-13-13 for help or visit

our website: www.karcher.com.mx

No detergent. Detergent suction tube not

properly connected to the ma-

chine.

Check connection.

Detergent is too thick. Dilute detergent, for best results

use Kärcher

®

detergent.

Filter on detergent suction tube

is clogged.

Run warm water through filter to

remove debris.

Damaged or clogged deter-

gent suction tube.

Remove obstruction or replace

detergent suction tube.

Spray wand is in high pressure

position.

Turn spray wand tip to low pres-

sure position.

Discharge nozzle is obstruct-

ed.

Blow out or remove debris with

fine needle.

Garden hose con-

nection leaks.

Loose fittings. Tighten fittings.

Missing/worn rubber washer. Insert new washer.

Spray wand leaks. Spray wand not properly at-

tached.

Insert the spray wand into the

trigger gun. Carefully press in

against the spring tension and

twist into the locked position.

Broken o-ring or plastic insert. Call Customer Support

Pump is noisy. Pump is sucking air. Check that hoses and fittings are

air tight. Turn off machine and

purge pump by squeezing trigger

gun until a steady flow of water

emerges through the nozzle.

Water leaks from

pump (up to 10

drops per minute is

permissible).

Loose fittings. Check that all fittings are tight.

Water seals are damaged or

worn.

Call Customer Support

Oil Drip. Oil seals are damaged or

worn.

Call Customer Support

Symptom Cause Solution

Customer Support

USA and Canada

Customer Support

Mexico

18 Français

Veuillez visiter :

www.karcher-register.com

pour enregistrer ce produit. Pour le support

technique, aller à :

www.karcher-help.com

Si vous avez acheté cet appareil neuf et qu'il

manque des pièces ou si vous souhaitez ef-

fectuer une demande de prise en garantie,

veuillez appeler :

1-800-537-4129

Il vous faudra faxer ou envoyer par courriel

votre facture à un agent du SAV. Toutes les

autres informations sont disponibles sous :

www.karcherresidential.com

Appeler : 01-800-024-13-13 pour obte-

nir de l'aide ou visiter notre site Web :

www.karcher.com.mx

DANGER

Identifie “une situation de danger immi-

nent qui, si elle n'est pas évitée, entraî-

ne la mort ou des blessures graves”.

ATTENTION

Identifie “une situation de danger poten-

tiel qui, si elle n'est pas évitée, pourrait

entraîner la mort ou des blessures”.

PRUDENCE

Identifie “une situation de danger poten-

tiel qui, si elle n'est pas évitée, peut

éventuellement entraîner des blessures

légères ou modérées” ou des domma-

ges matériels.

Avant d'utiliser ce nettoyeur pression, le

propriétaire et/ou l'utilisateur doit impé-

rativement avoir pris connaissance des

consignes d'utilisation et mises en gar-

de du fabricant.

Il est nécessaire d'insister sur les aver-

tissements et de les comprendre.

Si l'utilisateur ne parle pas couramment

l'anglais, l'acheteur/le propriétaire doit

lire les consignes et mises en garde du

fabricant avec l'utilisateur dans la lan-

gue maternelle de ce dernier et s'assu-

rer qu'il en comprend bien le contenu.

Le propriétaire et/ou l'utilisateur doit se

familiariser avec les consignes du fabri-

cant et les conserver afin de pouvoir s'y

référer ultérieurement.

NETTOYEUR HAUTE PRESSION - MANUEL D'UTILISATION

Généralités 19

Consignes de sécurité importantes 20 - 21

Instructions de montage 22

Mode d'emploi 22 - 23

Utilisation des accessoires 24

Emploi de détergents 24 - 25

Prendre une pause 25

Arrêt de l'appareil et nettoyage 26

Remisage hivernal et entreposage

à long terme

27

Instructions d'entretien et de main-

tenance

27

Conseils de nettoyage 28 - 29

Accessoires de nettoyage en option 30 - 31

Dépannage 32 - 34

Caractéristiques

Pression max. 1800 PSI

Débit d'eau max. 1.5 GPM

Ampérage 13 AMPS

Tension 120 V

N° de pièce 1.601-730.0

N° de série

Service après-vente

USA et Canada

Assistance Mexique

Symboles d'alerte de sécurité

Responsabilité du propriétaire/

de l'utilisateur

Français 19

1 Cordon d'alimentation avec disjonc-

teur différentiel

2 Poignée-pistolet

3 Verrouillage de sécurité de la poi-

gnée-pistolet

4 Tuyau à haute pression

5 Entrée d'eau avec raccord pour

tuyau d'arrosage

6 Poignée de transport

7 Compartiment de rangement des ac-

cessoires

8 Compartiment de rangement du

flexible haute pression

9 Compartiment de rangement de la

poignée-pistolet

10 Réservoir de détergent (amovible)

11 Tuyau d'aspiration du détergent

avec filtre

12 Sortie haute pression

13 Interrupteur marche/arrêt

14 Lance Vario

15 Dirtblaster® (lance rotative)

ATTENTION

Cette machine a été conçue pour être

utilisée avec des détergents du fabri-

cant. L'utilisation d'autres détergents

peut altérer le fonctionnement de la ma-

chine et annuler la garantie.

A usage domestique seulement !

GÉNÉRALITÉS

20 Français

ATTENTION !

En utilisant ce produit, toujours

observer une certaine pruden-

ce élémentaire, incluant notamment:

Lire toutes les instructions avant

d'utiliser le produit.

Afin de réduire le risque de blessu-

res, une surveillance attentive est re-

quise lorsqu'un produit est utilisé à

proximité d'enfants.

Savoir comment arrêter le produit et

réduire la pression rapidement. Etre

parfaitement familiarisé avec les

commandes.

Rester attentif — toujours regarder

ce que l'on fait.

Ne pas utiliser le produit en étant fa-

tigué ou sous l'influence de l'alcool

ou de drogues.

Ne laisser personne approcher la

zone de travail.

Ne pas se pencher ou se tenir sur un

support instable. Toujours rester en

équilibre.

Observer les instructions de mainte-

nance figurant dans le présent ma-

nuel.

Ce produit est fourni avec un dis-

joncteur différentiel monté dans la fi-

che du cordon d'alimentation. Si le

remplacement de la fiche ou du cor-

don d'alimentation s'avère nécessai-

re, n'utiliser que des pièces de

rechange identiques.

Risque d'injection ou de blessures

sur les personnes - ne pas diriger le

jet sur des personnes.

Utilisés abusivement, les jets à hau-

te pression peuvent être dangereux.

Le jet ne doit jamais être dirigé sur

des personnes, des animaux, des

appareils électriques ou la machine

même.

Porter des lunettes de protection.

Ne pas utiliser d'acides, ni de sol-

vants dans la machine. Ces produits

peuvent nuire à la santé de l'opéra-

teur et causer des dégâts matériels

irréversibles à la machine.

Afin de réduire le risque d'électrocu-

tion, garder toutes les connexions au

sec et ne pas les laisser à terre. Ne

pas toucher la fiche avec les mains

mouillées.

Le verrouillage de sécurité de la poi-

gnée-pistolet EMPECHE d'actionner

accidentellement la gâchette. Le dis-

positif de sécurité NE VERROUILLE

PAS la gâchette en position action-

née.

Ne pas utiliser que des rallonges.

Attention

Il est dangereux de trop arroser le maté-

riel et les câbles électriques.

Risque d´injection de peinture: le maté-

riel peut entraîner des graves blessures

s´il y a pénétration de la peau par la

peinture. Ne jamais pointer le pistolet

vers une personne ou vers soi-même.

en cas d´accident, demander immédia-

tement des soins médicaux.

Cet appareil peut produire une pression

de 12400 kPa /1800 PSI afin d´éviter

des ruptures et des blessures, ne pas

utiliser cette pompe avec des éléments

dont la pression nominale de service est

inférieure à 12400 kPa /1800 PSI (y

compris les pulvérisateurs, tuyaux flexi-

bles et raccords).

Couper le courant et détendre la pres-

sion avant de procéder au dépannage,

au nettoyage, ou d´enlever toute pièce.

CONSIGNES DE SECURITE IMPORTANTES

La page est en cours de chargement...

Kärcher K3 49M Mode d'emploi

Ce manuel convient également à

Kärcher K3 49M Mode d'emploi

dans d''autres langues

Documents connexes