OBSBOT ORB-2205-CT Le manuel du propriétaire

Taper
Le manuel du propriétaire
OBSBOT ORB-2205-CT
Tail Air Remote Controller
Design Specification
Version: V1.0
1.0 Introduction
1.1 Component Description
1. Power button
2. Laser emitter hole
3. Status indicator light
4. Camera control wheel (controls
zoom)
5. Multi-camera switching
6. Focus/Take photo Half-press for
focus; press fully to take photo
7. Record/Stop
8. Gimbal control Four-way control of
gimbal movement; single click to
reset gimbal; long press to activate
gyroscope.
9. Select/Cancel person tracking
10. Laser button Single click: laser;
double click: execute/cancel AI mode
11. Select/Cancel animal tracking
12. Preset position 1/2/3 Single click:
trigger preset position; long press:
add preset position
13. Remote control sleep/wake
toggle button
14. Camera switch 1/2/3 Single click:
control camera (green light); double
click: output camera video stream
(red light).
White
light
Tail Air connected
Red light
Camera output in
progress
Green
light
Current remote control
can control the camera
Light off
Tail Air not connected
If output and control are on the same
device, the red light will remain on.
15. Customizable button
Can be customized for function
16. USB-C interface
1.2 Pairing method
The following is the manual pairing method for the remote control and
Tail Air:
Prerequisites
Operation
Enter pairing
mode
Quickly press the "①" power button on the Tail Air three times,
and the status indicator light "②" on the Tail Air will turn into a
flashing blue light. At the same time, press and hold the remote
control's Person Tracking+1 dual keys for 3 seconds, and the
indicator light "②" on the remote control will change from steady
to flashing to enter Bluetooth pairing mode. Release the keys, and
the indicator light will continue to flash.
Note: The Bluetooth remote control supports multiple connections
to the Tail Air. Use the Person Tracking+ different device keys to
pair, for example: If you use the remote control's Person
Tracking+1 key combination to pair, the current Tail Air will be
configured as device 1. If you use the remote control's Person
Tracking+2 key combination to pair, the current Tail Air will be
configured as device 2. If you use the remote control's Person
Tracking+3 key combination to pair, the current Tail Air will be
configured as device 3.
Pairing status
Pairing successful: The Tail Air returns to its state before entering
Bluetooth pairing mode, with the blue light no longer flashing. The
indicator light on the remote control flashes three times quickly
and then goes off. The corresponding button on the remote
control can control the device with a steady green light, while
other added devices will have a steady white light. If a device is not
added or if an added device is not turned on, the light will not turn
on.
Pairing failed: The Tail Air indicator light will flash blue for 30
seconds, then flash red three times quickly and exit pairing mode.
The indicator light on the remote control will flash for 30 seconds,
then flash red three times quickly and exit pairing mode.
1.2 Attention
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
Caution: The user is cautioned that changes or modifications not expressly approved
by the party responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
FCC compliance statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction.
ISED Canada compliance statements:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:(1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio
peutfonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur)
approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de
brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.)
ne dépasse pas l'intensité nécessaire à l'établissement d'une communication.
The device has been evaluated to meet general RF exposure requirement. This
equipment should be installed and operated with minimum distance 0mm between
the radiator & your body.
L'appareil a été évalué pour répondre aux exigences générales d'exposition aux RF.
Cet équipement doit être installé et utilisé avec une distance minimale de 0 mm entre
le radiateur et votre corps.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

OBSBOT ORB-2205-CT Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues