FEUYMOENT LET614 Manuel utilisateur

Marque
FEUYMOENT
Modèle
LET614
Taper
Manuel utilisateur
Human baby sensing light strip
1.short press on cable to switch mode.
2.long press on cable to power on/off.
3.
FCC ID:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
NOTE
1. During use, if the switch can work normally, but the remote
control cannot, you need to perform the code matching operation.
2.if the light is interfered by other remote controls or cannot be
controlled remotely. Please power off and then power on again
before performing code matching.
3.After power on, the product is in automatic induction mode.
Equipped with automatic sensing and time control functions.
Automatically turn on lighting when someone is moving within the
detection range; When a person leaves, the lighting will continue
for 30 seconds before turning off.
How to perform code matching operation: Press and hold the power
button on the remoter for 3 seconds within 7 seconds of turning on
the power, the light strip flashes 3 times with white light,
indicating that the code (remote control) is matched.
NOTE
1. During use, if the switch can work normally, but the remote
control cannot, you need to perform the code matching operation.
2.if the light is interfered by other remote controls or cannot be
controlled remotely. Please power off and then power on again
before performing code matching.
3.After power on, the product is in automatic induction mode.
Equipped with automatic sensing and time control functions.
Automatically turn on lighting when someone is moving within the
detection range; When a person leaves, the lighting will continue
for 30 seconds before turning off.
How to perform code matching operation: Press and hold the power
button on the remoter for 3 seconds within 7 seconds of turning on
the power, the light strip flashes 3 times with white light,
indicating that the code (remote control) is matched.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interferenceto radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
ISED Warning
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the foll owing two conditions: (1)this device may not cause
interference, and(2) this device must accept any interference, includinginterference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
auxappareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et(2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre lefonctionnement.
NOTE: This equipment has been tested and found to c
The device has been evaluated to meet general RF exposure requirement. The device
can be used installed and operated with minimum distance 0mm between the radiator
and your body.
L'appareil a été évalué pour répondre aux exigences générales d'exposition
aux RF.Cet équipement doit être installé et utilisé avec une distance minimale de
0 mm entre le radiateur et votre corps.
  • Page 1 1
  • Page 2 2
  • Page 3 3

FEUYMOENT LET614 Manuel utilisateur

Marque
FEUYMOENT
Modèle
LET614
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents