DT Research 313T Mobile Tablet Mode d'emploi

Marque: DT Research

Modèle: 313T Mobile Tablet

Taper: Mode d'emploi

Mobile Tablet

313T/MD

INTRODUCTION

Thank you for acquiring the 313T, part of DT Research’s line of mobile tablets.

Featuring a slim, robust enclosure, the 313T/MD with a 13.3” TFT display is powered

by the Intel® processor, oﬀering optimal combinations of performance and power

savings.

The 313T/MD is available with Microsoft® Windows® or Ubuntu operating system.

Each software operating system features web browser, client/ server computing

software, media player, accessories, and applications support.

PACKAGE CONTENTS

• One 313T/MD with Battery Pack and Handstrap

• AC-DC Power Adapter with Power Cord

• Basic Operation Guide

DT Research, Inc.

2000 Concourse Drive, San Jose, CA 95131

BOG111921 313T/MD C ENG

Battery/Power LED

Power/Battery LED Status:

• Blue indicates the battery is 25% to 100% charged

• Blinking blue indicates the battery is charging

• Orange indicates that the battery is between 11% to 25%

• Blinking Orange indicates that the battery is below 10%

PRECAUTIONS

• Always exercise care when operating and handling the 313T/MD.

• Do NOT apply excessive pressure to the display screen.

• We recommend using the Digital Pen (optional) to keep the screen clean.

• Avoid prolonged exposure of the display panel to any strong heat source.

Wherever possible, the 313T/MD should face away from direct light to reduce

glare.

• If the AC-DC power adapter is used to recharge or power the tablet, do NOT use

any AC-DC adapter other than the one provided or acquired from the manufac-

turer or its partners.

• In the unlikely event that smoke, abnormal noise, or strange odor is present,

immediately power oﬀ the 313T/MD and disconnect all power sources. Report

the problem to your device provider immediately.

• Never attempt to disassemble the 313T/MD, as this will void the warranty.

Input/ Output Ports

HDMI-out

Button Functions

BASIC FEATURES

The 313T/MD wireless tablet integrates a bright and multi-touch display, one USB

port, and embedded networking elements such as wireless LAN and Bluetooth. The

313T/MD is complemented by a suite of accessories, including battery expansion,

charging cradles, and battery charger kit, for a comprehensive user experience.

A 313T/MD typically integrates an 802.11ax wireless LAN (WLAN) adapter that may

connect to other wireless devices or access points. If your 313T/MD does not come

with such a network adapter, please consult your device provider to establish the

desired network connectivity.

C USB 2.0 Ports

A Ethernet Port D Headphone-out

E USB 3.0 Port

F DC-in

BUTTON ACTION

Programmable Button

2 Power Button

3 Trigger button

Battery Latch

OPERATION

Powering ON and OFF

To activate the 313T/MD, push and quickly release the Power Button. The display will

come on in a few seconds. To put the 313T/MD in Standby mode, push and quickly

release the Power Button. To turn the 313T/MD oﬀ for extended storage, power

oﬀ safely using any software function that “shuts down computer” provided in the

software operating system.

Start Up

If the power up (from Standby mode or otherwise) is successful, the appropriate

interface will be displayed after a launch sequence of several seconds. The wireless

LAN connection may take 10-15 seconds to be established.

Conﬁguring the Mobile Tablet

The 313T/MD may be configured using the utilities and methods dictated by

the software operating system. The 313T/MD should be configurable for various

properties such as user profiles, network features, and several system elements.

Wireless Networking

Wireless LAN

The 313T/MD is often delivered with an embedded (user-inaccessible) 802.11ax

WLAN adapter equipped with a hidden custom antenna.

• Through the support of typical WLAN adapters, the 313T/MD should be able to

detect all 802.11 access points in the vicinity for you to select the access point of

your choice for connection.

• The SSID and WEP/WPA/WPA2 (if enabled) parameters on the 313T/MD and the

access points have to match. The SSID is case-sensitive and it is recommended

that you enable WEP/WPA/WPA2 encryption (or advanced alternatives) for

secure access.

• When WEP/WPA/WPA2 is enabled, you may need to consult your network

administrator or your networking equipment literature to properly configure

associated settings such as Authentication mode, etc.

• Refer to the access point operating manuals for setting up the 802.11 access

points.

Bluetooth

The 313T/MD oﬀers the Bluetooth module which supports Bluetooth 5.2 standard

including Bluetooth 3.0 High Speed and Bluetooth 4.0 Low Energy, which delivers

faster speeds with low power consumption.

NOTE:

To conserve power, use (push and quick release) the Power Button to put the

tablet in “Standby” mode while not in use. Pushing briefly on the same button

will wake up the system within seconds.

NOTE:

When the batterypack is charging, the blue-colored Battery LED should blink

slowly. If plugging in the AC-DC adapter does not trigger this blinking activity

and the LED stays dark, the battery pack may have been drained substantially.

Try unplugging/ replugging the AC-DC adapter to the 313TT a few times to

activate the charging process.

NOTE:

The battery packs shipped with your tablet may be low in power—please use

the AC-DC adapter with the 313TT when setting up for the first time to fully

charge the internal battery pack. You may charge the external battery pack with

it attached to the 313TT, or with the optional external battery charger kit.

NOTE:

Avoid using the Power Button (“hold 4+ seconds” feature) to turn oﬀ the tablet—

this form of hardware shutdown is intended to be a means of recovery from

lockups, and not as normal operation.

To Hold the Tablet

Left hand: grip the left back side of the tablet

with your left hand four index fingers, with

thumb resting on the top of the back side of the

tablet and palm securely against the back.

Right hand: grip the right back side of the tablet

with your right hand four index fingers, with

thumb resting on the top of the back side of the

tablet and palm securely against the back.

USING THE MOBILE TABLET

Peripherals Support

Through its USB port, the 313T/MD supports a wide range of USB-based peripherals.

These peripherals are applicable for software installation, applications storage, data

storage, and system software recovery and updates.

For More Support

Users can download the Tablet Modules Basic Operation Guides from the DT

Research website.

RF Exposure Information (RED & UKCA)

To be protected against all verified adverse effects, the separation distance of at least 0mm must be maintained between the antenna of the radio having max. 6.8dBi antenna and all persons.

Hereby, [DT Research, Inc.] declares that the radio equipment type [313T/MD] is in compliance with Directive 2014/53/EU and UK Radio Equipment Regulations 2017. The full text of the EU and UK

declaration of conformity is available at the following internet address: http://www.dtresearch.com.

The functions of Wireless Access Systems including Radio Local Area Networks(WAS/RLANs) within the band 5150-5250 MHz for this device are restricted to indoor use only within all European

Union countries (BE/BG/CZ/DK/DE/EE/IE/EL/ES/FR/HR/ IT/CY/LV/LT/LU/HU/MT/NL/AT/PL/PT/RO/SI/SK/FI/SE/TR/N O/CH/IS/LI/UK(NI).

Maximum EIRP for EU

Bluetooth:2402MHz-2480MHz 10.27dBm

Bluetooth LE:2402MHz-2480MHz

7.00dBm

Wifi: 2412MHz-2472MHz/2422MHz-2462MHz

18.47dBm

Wifi: 5150MHz-5725MHz 21.98dBm

Wifi: 5725MHz-5875MHz 13.96dBm

This equipment complies with Directive 2014/53/EU and UK Radio Equipment Regulations 2017 radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific

operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves established by European Union market(France). These requirements set a SAR limit of 2W/kg averaged over

one gram of tissue. The highest SAR value 1.587W/kg reported under this standard during product certification for use when properly worn on the body.

The equipment has been tested with radios set to their highest transmission levels with following setup:

Mode

use against the head

worn or carried against the torso of the body

Worn on limbs

Separation

0 mm

SAR Value

1.587 W/kg

Sar Limit

2W/kg (over 10 g)

4W/kg (over 10 g)

Body-worn accessories (e.g., carry case, belt clip) containing metallic components which has not been tested or certified may change the RF performance of the device, including its compliance with

RF exposure. User shall avoid using such accessories and should operate at least the above stated separation distance to maintain RF exposure compliance.

Operating authorizations must exist to operate the product in the following member states of the European Union, refer to the table below.

Importer Name: Concept International GmbH

Importer Address: Zweibrückenstr. 5-7 80331 München Germany

Federal Communication Commission Interference

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

RF Exposure Compliance

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves established by the FCC. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The

highest SAR value reported under this standard during product certification for use when properly worn on the body, with 0mm separation.

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Unique Identifier Trade Name:

Model No.: 313T/MD

Responsible Party – U.S. Contact Information

DT Research, Inc.

2000 Concourse Drive, San Jose, CA 95131

http://www.dtresearch.com

IC Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the

following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

(1) L’appareil ne doit pas produire de brouillage;

(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Cet équipement est conforme aux limites d'exposition aux radiations IC CNR-102 établies pour un environnement non contrôlé.

This Class [B] digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

RF Exposure Compliance

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The

highest SAR value reported under this standard during product certification for use when properly worn on the body, with 0mm separation.

Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement non contrôlé. L’utilisateur final doit suivre les instructions spécifiques pour satisfaire

les normes. Cet émetteur ne doit pas être co-implanté ou fonctionner en conjonction avec toute autre antenne ou transmetteur.

Le dispositif portatif est conçu pour répondre aux exigences d’exposition aux ondes radio établie par le développement énergétique DURABLE. Ces exigences un SAR limite de 1,6 W/kg en moyenne

pour un gramme de tissu. La valeur SAR la plus élevée signalée en vertu de cette norme lors de la certification de produit à utiliser lorsqu’il est correctement porté sur le corps, avec une séparation de

0mm.

The functions of Wireless Access Systems including Radio Local Area Networks(WAS/RLANs) within the band 5150-5250 MHz for this device are restricted to indoor use only.

Les fonctions des systèmes d'accès sans fil, y compris les réseaux locaux radioélectriques (WAS/RLAN), dans la bande 5150-5250 MHz de cet appareil sont limitées à une

utilisation en intérieur.