Segway E25A Manuel utilisateur

Ninebot KickScooter

User Manual

Original Instructions

K014P0879-A1

www.segway.com

Producent zastrzega sobie prawo do wprowadzania zmian w produkcie, aktualizacji oprogramowania i aktualizacji tej

instrukcji obsługi w dowolnym momencie. Odwiedź stronę www.segway.com lub sprawdź aplikację, aby pobrać

najnowsze materiały użytkownika. Musisz zainstalować aplikację, aktywować swojego KickScootera i uzyskać

najnowsze aktualizacje i zasady bezpiecze stwa.

Thanks for choosing the Ninebot KickScooter (hereinafter referred to as KickScooter)!

Your KickScooter is a fashionable transportation device with mobile app, allowing you to connect with other riders.

Enjoy your ride and interact with riders worldwide!

This manual is applicable to the following models:

E22 series: E22 / E22D / E22E

E25 series: E25A / E25D / E25E

E45 series: E45 / E45D / E45E

Contents Thanks for choosing the Ninebot KickScooter!

4 Assembling Your KickScooter

5 Installing a Second Battery Pack (optional)

1 Riding Safety

2 Packing List

3 Diagram

6 First Ride

7 Charging

8 Learning to Ride

9 Warnings

11 Maintenance

13 Certiﬁcations

12 Speciﬁcations

10 Folding and Carrying

14 Trademark and Legal Statement

15 Contacts

02

04

05

06

07

08

09

11

15

17

15

20

23

WARNING!

Always use both electronic brake and foot brake for emergency stopping. Otherwise you risk falls and/or

collisions from not achieving the max. braking capability.

* The picture is for reference only. Please refer to the actual product for more details.

01

1 Riding Safety

1. The KickScooter is a recreational product. Before mastering riding skills, you need to practice. Neither Ninebot Inc. (means Ninebot

(Beijing)TechCo.,Ltd. and its subsidiaries and aﬃliates) nor Segway Inc. is responsible for any injuries or damage caused by a

rider's inexperience or failure to follow the instructions in this document.

2. Please understand that you can reduce the risk by following all the instructions and warnings in this manual, but you cannot

eliminate all the risks. Remember that whenever you ride the KickScooter you risk injury from loss of control, collisions, and falls.

When entering into public spaces always comply with the local laws and regulations. As with other vehicles, faster speeds require

longer braking distance. Sudden braking on low traction surfaces could lead to wheel slip, or falls. Be cautious and always keep a

safe distance between you and other people or vehicles when riding. Be alert and slow down when entering unfamiliar areas.

3. Always wear a helmet when riding. Use an approved bicycle or skateboard helmet that ﬁts properly with the chin strap in place, and

provides protection for the back of your head.

4. Do not attempt your ﬁrst ride in any area where you might encounter children, pedestrians, pets, vehicles, bicycles, or other

obstacles and potential hazards.

5. Respect pedestrians by always yielding the right of way. Pass on the left whenever possible. When approaching a pedestrian from

the front, stay to the right and slow down. Avoid startling pedestrians. When approaching from behind, announce yourself and slow

down to walking speed when passing. Please obey local traﬃc laws and regulations if situation is diﬀerent.

6. In places without laws, comply with the safety guidelines outlined in this manual. Neither Ninebot Inc. nor Segway Inc. is

responsible for any property damage, personal injury/death, accidents, or legal disputes caused by violations of the safety

instructions.

7. Do not allow anyone to ride your KickScooter on his/her own unless they have carefully read this manual and followed the New

Rider Tutorial in the App. The safety of new riders is your responsibility. Assist new riders until they are comfortable with the basic

operation of the KickScooter. Make sure each new rider wears a helmet and other protective gear.

8. Before each ride check for loose fasteners and damaged components. If the KickScooter makes abnormal sounds or signals an

alarm, immediately stop riding. Diagnose your KickScooter via the Segway-Ninebot App and call your dealer/distributor for service.

9. Be alert! Scan both far ahead and in front of your KickScooter — your eyes are your best tool for safely avoiding obstacles and low

traction surfaces (including, but not limited to, wet ground, loose sand, loose gravel, and ice).

10. To reduce risk of injury, you must read and follow all “CAUTION” and “WARNING” notices in this document. Do not ride at an unsafe

speed. Under no circumstance should you ride on roads with motor vehicles. The manufacturer recommends riders be 14+ years

old. Always follow these safety instructions:

A. People who should not ride the KickScooter include:

i. Anyone under the influence of alcohol or drugs.

ii. Anyone who suﬀers from disease that puts them at risk if they engage in strenuous physical activity.

iii. Anyone who has problems with balance or with motor skills that would interfere with their ability to maintain balance.

iv. Anyone whose weight is outside the stated limits (see Speciﬁcations).

v. Pregnant women.

B. Riders under the age of 18 years old should ride under adult supervision.

C. Comply with local laws and regulations when riding this product. Do not ride where prohibited by local laws.

D. To ride safely, you must be able to clearly see what is in front of you and you must be clearly visible to others.

E. Do not ride in the snow, in the rain, or on roads which are wet, muddy, icy, or that are slippery for any reason. Do not ride over

obstacles (sand, loose gravel, or sticks). Doing so could result in a loss of balance or traction and could cause a fall.

11. Do not attempt to charge your KickScooter if it, the charger, or the power outlet is wet.

12. As with any electronic device, use a surge protector when charging to help protect your KickScooter from damage due to power

surges and voltage spikes. Only use the Segway supplied charger. Do not use a charger from any other diﬀerent product models.

13. Use only Ninebot or Segway approved parts and accessories. Do not modify your KickScooter. Modiﬁcations to your KickScooter

could interfere with the operation of the KickScooter, result in serious injury and/or damage, and void the Limited Warranty.

14. Children should not play with the KickScooter or parts of it nor should cleaning or maintenance be done by children. The use of the

machine results in the transmission of vibrations throughout the driver's body.

15. Always place the KickScooter on its stand on a flat and stable surface. The KickScooter must be placed with the stand against the

slope to prevent it from tipping over. Never place the KickScooter with the front facing down the slope, as the stand may close and

tip the machine. Once the KickScooter is on its stand, check its stability to avoid any risk of falling (by slip, wind or slight jolt). Do

not park the KickScooter in a busy area, but rather along a wall. If possible, always choose to park your KickScooter on flat ground.

16. For a better driving experience, it is recommended to conduct a regular maintenance of the product.

17. Please read the user manual before charging the battery.

18. Do not touch the brake system, it could cause injuries.

19. The A-weighted emission sound pressure level is less than 70 dB(A). The mechanical vibrations transmitted by the KickScooter are

less than 2.5 m/s2.

0302

3 Diagram

Rear fender/Foot brake

Insurance plate area*

* For E22D, E25D and E45D.

Magnetic Brake*

* For E25 and E45 series.

Folding pedal

Dashboard & Power button

Electronic throttle

Kickstand

Stem (battery cabin)

Hub motor

Reflector*

* For E22D, E22E, E25 and E45 series.

Headlight

Dashboard & Power button

Speedometer: Indicates the current speed. Also displays error codes when faults are detected.

Battery level: Indicates the remaining battery level with 5 bars. Each bar equates to approximately 20% power level.

Power mode:

—Red "S" icon: Sport mode (maximum power/speed).

—White "S" icon: Standard mode (moderate power/speed).

—No "S" icon: Speed limit mode (minimum power/speed).

Bluetooth: A blinking Bluetooth icon indicates that the vehicle is ready to connect. A solid Bluetooth icon indicates that the vehicle is

connected to a mobile device.

Power button: Short press to power on. Long press to power oﬀ. When powered on, press to turn on/oﬀ the headlight. Double-press to

change power mode.

Overheat tip: The thermometer icon always on indicates that the battery temperature has reached 122°F (50°C). At this point, the vehicle

cannot accelerate normally and may not be charged. Do not use it until the temperature is restored to normal range.

Error display: The lit wrench icon indicates the scooter error.

Electronic brake

Folding latch

Second Battery Pack*

* For E45 series.

Charge port

Reflector*

* For E22D, E22E,

E25 and E45 series.

Second battery port

2 Packing List

Handlebar Mainframe

When unboxing your KickScooter, please verify that the above items are included in the package. If any components are missing, please

contact your dealer/distributor or nearest service center (see Contacts in the user manual). After verifying that all components are

present and in good condition, you can assemble your new KickScooter.

Please retain the box and packaging materials in case you need to ship your KickScooter in the future.

Remember to power oﬀ your KickScooter and unplug the charge cable before assembling, mounting accessories, or cleaning the

mainframe.

Accessories

Screw × 7

(one extra)

3mm Hex Wrench Battery Charger

User Materials

Second Battery Pack

QUICK STARTUSER MANUAL LIMITED WARRANTY

E22 series

NEB1002-H1 NEB1002-H1 NEB1002-U1

E25 series E45 series

Included

Sold separately

Applicable scooter model

Battery Model

Bell

Power button

(multi-functional)

Bluetooth

Speedometer

Power mode

Overheat tip

Power level

Error display

* ONLY use the battery in the applicable model. Otherwise there will be damage

or dangers.

0504

4 Assembling Your KickScooter

3. Install six screws (two on each side) with the

included hex wrench.

4. Verify that your KickScooter powers on and oﬀ.

2. Firmly connect the wires inside the handlebar

and the stem. Slide the handlebar onto the

stem. Be aware of the correct orientation.

1. Unfold the stem and push it until you hear a

click. Flip up the folding pedal. Then unfold

the kickstand to support the scooter.

Note: Conﬁrm that the latching axis on the

folding mechanism is secured correctly.

3. Install the external battery on the rail and ﬁx it with the M4 (20mm)

screws (2 pcs) and M3 screw (1 pcs), provided with this product.

After they are properly installed, block the screw holes with the

rubber stopper.

2. Install the rail with the M4 (10mm) screws (3

pcs), provided with this product. Please make

sure it is properly ﬁxed.

4. Verify that your KickScooter powers on and oﬀ.

1. Remove the three screws on the stem. Then remove the

cover near the charge port and remove the M3 screw.

5 Installing a Second Battery Pack (optional) Warning: please use the screws provided with

this product only.

Headlight

facing front

Latching Axis

1

4

3

6

2

5

0706

7 Charging

8 Learning to Ride

Wear an approved helmet and other protective gear

to minimize any possible injury.

1. Power on the scooter and check the battery

level. Charge the scooter if the battery level

is low.

6 First Ride There are safety risks when learning to ride the KickScooter. You must read the Riding

Safety via the App before your ﬁrst ride.

For your safety, your new KickScooter is not activated and will beep occasionally after

POWER ON.

Until activated, the KickScooter maintains a very low riding speed, and can not perform with

full function. Install the Segway-Ninebot App on your mobile device (with Bluetooth 4.1 and

above), connect to the KickScooter with Bluetooth, and follow the App instructions to

activate your KickScooter and enjoy the full performance.

Scan the QR code to download the App (iOS 9.0 and above, Android™ 4.3 and above).

Your KickScooter is fully charged when the LED on the charger changes from red (charging) to green (trickle charge).

Close the charge port cover when not charging.

2

1Install the Segway-Ninebot App and register/login.

3

4

Click “Vehicle” “Search vehicle” to connect to your

KickScooter.

The KickScooter will beep when it has successfully

connected. The Bluetooth icon will stop blinking and

remain illuminated.

Follow the App instructions to activate the KickScooter and learn how to ride safely.

You can now start to use your KickScooter, check the status with the App, and interact with other users. Have fun!

WARNING

Do not connect the charger if the charge port or charge cable is wet. Do not charge or use your battery if it is damaged

or see trace of water.

Close the charge

port cover when

ﬁnished.

Open the charge

port cover.

Insert the

charge plug.

Charge port

Charging steps:

Power on the KickScooter. A blinking Bluetooth icon

indicates the KickScooter is ready to connect.

Charge port

(When used with

second battery)

Vehicle Fans Moments MeDiscover

Segway-Ninebot App

0908

WARNING

When braking rapidly, you risk serious injury due to loss of traction and falls. Maintain a moderate speed and look out

for potential hazards.

3. Put your other foot on the foot deck to keep both

feet stable. Press the throttle to speed up when you

are balanced.

Note: For your safety, the motor will not engage

until the scooter reaches 2.5 mph (4 km/h) The

speed is adjustable via the Segway-Ninebot App.

4. Slow down by releasing the throttle. Squeeze

the electronic brake and stamp the rear

fender with foot at the same time for a

brake.

2. Stand on the foot deck with one foot and

push oﬀ with another foot to start gliding.

5. To turn, shift your body and turn the

handlebar slightly.

Watch your head when passing

through doorways.

Watch your speed when traveling downhill. Use both

brakes together when traveling at high speed.

Keep your speed between 3.1–6.2 mph (5–10 km/h) when you ride

through speed bumps, elevator door stills, bumpy roads or other

uneven surfaces. Slightly bend your knee to better adjust

mentioned surfaces.

9 Warnings

DO NOT ride the

scooter in the rain.

WARNING

Failure to follow these instructions could lead to serious injury.

1110

DO NOT rotate the handlebar violently

while driving at high speed.

DO NOT ride on public roads,

motorways, or highways.

Do not ride through puddles or any

other (water) obstacles. In such a case

please lower your speed and bypass

the obstacle.

The KickScooter is for one rider only.

Do not ride with another person. Do not

carry a child.

DO NOT press the throttle when walking

with the scooter.

DO NOT carry heavy objects on the

handlebar.

DO NOT ride the scooter with

only one foot.

Avoid contacting obstacles with the

tire/wheel.

1312

11 Maintenance

Cleaning and Storage

Use a soft, wet cloth to wipe the mainframe clean. Hard to remove dirt can be scrubbed with a toothbrush and toothpaste, then cleaned

with a soft, wet cloth.

NOTE

Do not wash your KickScooter with alcohol, gasoline, acetone, or other corrosive/volatile solvents. These substances may damage the

appearance and internal structure of your KickScooter. Do not wash your KickScooter with a power washer or hose.

WARNING

Make sure the KickScooter is powered OFF, the charging cable is unplugged, and the rubber cap on the charge port is tightly sealed before

cleaning; otherwise you may damage the electronic components.

Store your KickScooter in a cool, dry place. Do not store it outdoors for extended periods of time. Exposure to sunlight and temperature

extremes (both hot and cold) will accelerate the aging process of the plastic components and may reduce battery life.

10 Folding and Carrying

Folding

Step on the folding pedal while pushing

the handlebar forward slightly.

Then fold the handlebar down

until it locks into the rear

fender.

When your KickScooter is

folded up, simply lift it by the

stem to carry.

DO NOT take your hands oﬀ the

handlebar while riding. Do not ride with

one hand only.

DO NOT ride up and down stairs or jump

over obstacles.

DO NOT touch the hub motor after riding

because it can get hot.

DO NOT step on the folding

pedal while riding.

WARNING

Always keep both hands on the handlebar or you risk serious injury due to loss of balance and falls.

Maintenance and removal of the battery

Do not remove the battery. Removing the battery is complicated and can alter the operation of the machine: You can contact an

authorized repairer if the product is still guaranteed. If the product is not guaranteed you can contact any specialized repairer of your

choice. You can ask for the list of the authorized repairers to the customer service available at www.segway.com. For any further question,

you can contact the customer service available at www.segway.com.

Do not store or charge the battery at temperatures outside the stated limits (see Speciﬁcations). Do not puncture the battery. Refer to

your local laws and regulations regarding battery recycling and/or disposal. A well maintained battery can perform well even after many

miles of riding. Charge the battery after each ride and avoid draining the battery completely. When used at room temperature (70°F

[22°C]) the battery range and performance is at its best; whereas using it at temperatures below 32°F (0°C) can decrease range and

performance. Typically, at -4°F (-20°C) range can be half that of the same battery at 70°F (22°C). Battery range will recover when

temperature rises. More details are available in the App.

Replace the Tires

Tires supplied with the product are to be mounted on the wheel by a professional repairer. Removing the wheels is complicated and

incorrect assembly can lead to instability and malfunctions:

– Please contact an authorized repairer if the product is still under manufacturer guarantee. You can ask for the list of the authorized

repairers to the customer service available at www.segway.com.

– If the product is no longer under guaranteed you can contact any specialized repairer of your choice.

– Should you have questions, you can contact customer service available at www.segway.com.

NOTE

Typically, a fully charged battery should retain charge for 120-180 days in Standby Mode. A low-power battery should retain charge for

30-60 days in Standby Mode. Remember to charge the battery after each use. Completely draining the battery may cause permanent

damage to the battery. Electronics inside the battery record the charge-discharge condition of the battery; damage caused by

over-discharge or under-discharge will not be covered by the Limited Warranty.

WARNING

Do not charge or use your battery if it is damaged or see trace of water. Do not attempt to disassemble the battery. Risk of ﬁre. No user

serviceable parts.

WARNING

Do not ride when the ambient temperature is outside the machine operation temperature (see Speciﬁcations) because low/high

temperature will limit the maximum power/torque. Doing so could cause personal injury or property damage due to slips or falls.

Others

The external flexible cable of this transformer cannot be replaced; if the cord is damaged, the transformer must be discarded and

replaced by a new one. Should you have questions, you can contact customer service available at www.segway.com.

In case of accident or breakdown: Please contact an authorized repairer if the product is still under guarantee. If not, you can contact any

specialized repairer of your choice. You can ask for the list of the authorized repairers to the customer service available at

www.segway.com. For any question, please contact customer service available at www.segway.com.

Eﬀorts have been made to simplify wording in the user manual for users. Where an action appears too complicated for a user, he is

advised to contact an authorized or a specialized repairer or customer service.

1514

Cleaning and Storage

Use a soft, wet cloth to wipe the mainframe clean. Hard to remove dirt can be scrubbed with a toothbrush and toothpaste, then cleaned

with a soft, wet cloth.

NOTE

Do not wash your KickScooter with alcohol, gasoline, acetone, or other corrosive/volatile solvents. These substances may damage the

appearance and internal structure of your KickScooter. Do not wash your KickScooter with a power washer or hose.

WARNING

Make sure the KickScooter is powered OFF, the charging cable is unplugged, and the rubber cap on the charge port is tightly sealed before

cleaning; otherwise you may damage the electronic components.

Store your KickScooter in a cool, dry place. Do not store it outdoors for extended periods of time. Exposure to sunlight and temperature

extremes (both hot and cold) will accelerate the aging process of the plastic components and may reduce battery life.

[1] Typical Range: tested while riding under full power, 165 lbs (75 kg) load, 77°F (25°C), 60% of max. speed on average on pavement.

* Some of the factors that aﬀect range include: speed, number of starts and stops, ambient temperature, etc.

[2] All KickScooter models could install the second battery. Some of the parameters would change in this case.