Seura STM3-49-U Manuel utilisateur

Taper
Manuel utilisateur
USER MANUAL
WWW.SEURA.COM
DISPLAY SIZES 49-INCH, 55-INCH, 65-INCH, 86-INCH
Ultra Bright
Outdoor Display
MODEL NUMBERS
STM3-49-U
STM3-55-U
STM3-65-U
STM3-86-U
2
Warnings
A warning that an apparatus with class I construction shall be connected
to a MAINS socket outlet with a protective earthing connection
WARNING
To prevent injury, this apparatus must be securely attached to the oor/
wall in accordance with the installation instructions.
Where the MAINS plug or an appliance coupler is used as the disconnect
device, the disconnect device shall remain readily operable;
The apparatus shall not be exposed to dripping or splashing and no
objects lled with liquids, such as vases, shall be placed on the apparatus.
To reduce the risk of re or electric shock, do not expose the inside of this
apparatus to rain or moisture. The inside of this apparatus shall not be
exposed to dripping or splashing.
WARNING
Never place a display in an unstable location. A display set may fall,
causing serious personal injury or death. Many injuries, particularly to
children, can be avoided by taking simple precautions such as:
- Using cabinets or stands recommended by the manufacturer of the
display.
- Only using furniture that can safely support the display.
- Ensuring the display is not overhanging the edge of the supporting
furniture.
- Not placing the display on tall furniture (for example, cupboards or
bookcases) without anchoring both the furniture and the display to a
suitable support.
- Not placing the display on cloth or other materials that may be located
between the display and supporting furniture.
- Educating children about the dangers of climbing on furniture to reach
the display or its controls.
If your existing display is being retained and relocated, the same
considerations as above should be applied.
ATTENTION
Ne placez jamais un téléviseur dans un endroit instable. Un téléviseur peut tomber
et causer des blessures graves ou mortelles. Beaucoup de blessures, en particulier
aux enfants, peuvent être évités en prenant des précautions simples telles que:
- Utilisation des armoires ou des supports recommandés par le fabricant du
téléviseur.
- Seulement en utilisant des meubles qui peuvent supporter en toute sécurité le
téléviseur.
- Assurer le téléviseur est pas surplombant le bord du meuble de support.
- Non placer le téléviseur sur un grand meuble (par exemple, des armoires ou des
bibliothèques ) sans accrocher à la fois les meubles et le téléviseur sur un support
approprié.
- Non placer le téléviseur sur le tissu ou d’autres matériaux qui peuvent être situés
entre le téléviseur et le mobilier de soutien.
- Éduquer les enfants sur les dangers de grimper sur un meuble pour atteindre le
téléviseur ou ses commandes.
Si votre téléviseur existant est conservé et transféré, les mêmes considérations que
ci-dessus doivent être appliquées.
Un avertissement qu’un appareil de construction de CLASSE I doit être connecte à un
socle du réseau d’alimentation muni d’une connexion à la terre de protection.
ATTENTION
Pour éviter tout accident, cet appareil doit être xe de façon sure au sol ou au mur
conformément aux instructions d’installation.
Lorsque la prise du RESEAU DALIMENTATION ou une prise placée sur l’appareil
est utilisée comme dispositif de déconnexion, ce dispositif doit demeure aisément
accessible;
Le mode d’emploi doit stipuler que l’appareil ne doit pas être expose à des
égouttements d’eau ou des éclaboussures et de plus qu’aucun objet rempli de liquide
tel que des vases ne doit être place sur l’appareil.
Pour réduire le risque d’incendie ou de choc électrique, ne pas exposer l’intérieur de cet
appareil à la pluie ou à l’humidité. L’intérieur de cet appareil ne doit pas être exposé à
des gouttes ou des éclaboussures.
WARNINGS AVERTISSEMENTS
3
Important Safety Instructions
Apparatus shall not be exposed to dripping or splashing and no objects
lled with liquids, such as vases, shall be placed on the apparatus.
WARNING – TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THE SET
TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any of the ventilation openings. Install in accordance with
the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves,or other apparatus (including ampliers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong is provided for your safety. When the
provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11) Only use the attachments/accessories specied by
the manufacturer.
12) Use only with a cart, stand, tripod, bracket, or
table specied by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualied service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
15) The apparatus shall not be exposed to dripping or splashing and that
no objects lled with liquids, such as vases, shall be placed on the
apparatus.
16) Shall be connected to a MAINS socket outlet with a protective earthing
connection.
17) The disconnect device shall remain readily operable.
18) The socket-outlet shall be installed near the equipment and shall be
easily accessible.
L’appareil ne doit pas être exposé à des gouttes ou des éclaboussures et aucun objet
rempli de liquide, comme des vases, doit être placé sur l’appareil.
AVERTISSEMENT - POUR ÉVITER D’INCENDIE OU DE CHOC ÉLECTRIQUE NE PAS
EXPOSER L’ENSEMBLE À LA PLUIE OU À L’HUMIDITÉ.
CONSIGNES DE SÉCURITÉ IMPORTANTES
1) Lisez ces instructions.
2) Conservez ces instructions.
3) Respectez tous les avertissements.
4) Suivez toutes les instructions.
5) Ne pas utiliser cet appareil près de l’eau.
6) Nettoyer uniquement avec un chiffon sec.
7) Ne pas bloquer les ouvertures de ventilation. Installez conformément aux
instructions du fabricant.
8) Ne pas installer près de sources de chaleur telles que des radiateurs, registres de
chaleur, poêles ou autres appareils (y compris les amplicateurs) qui produisent de
la chaleur.
9) Ne pas contourner le dispositif de sécurité de la che polarisée ou mise à la terre.
Une che polarisée possède deux lames dont une plus large que l’autre. Une prise
de terre a deux lames et une troisième broche de mise à la terre. La lame large ou
la troisième broche est fournie pour votre sécurité. Si la che fournie ne rentre pas
dans votre prise, consultez un électricien pour remplacer la prise obsolète.
10) Protégez le cordon d’alimentation d’être piétiné ou pincé, en particulier au niveau
des ches, des prises de courant, et le point où ils sortent de l’appareil.
11) Utilisez uniquement les xations / accessoires spéciés par
le fabricant.
12) Utilisez uniquement avec un chariot, un support, un
trépied, un support ou une table spécié par le fabricant
ou vendu avec l’appareil. Quand un chariot est utilisé,
faites attention lorsque vous déplacez l’ensemble chariot /
appareil pour éviter les blessures en cas de chute.
13) Débranchez l’appareil en cas d’orage ou lorsqu’il est
inutilisé pendant de longues périodes de temps.
14) Les travaux de personnel qualié. Une réparation est nécessaire lorsque l’appareil
a été endommagé de quelque façon que ce cordon d’alimentation ou la che est
endommagé, du liquide a été renversé ou des objets sont tombés dans l’appareil,
l’appareil a été exposé à la pluie ou à l’humidité, ne fonctionne pas normalement,
ou est tombé.
15) L’appareil ne doit pas être exposé à des gouttes ou des éclaboussures et aucun
objet rempli de liquide, comme des vases, ne doit être placé sur l’appareil.
16) doit être relié à une prise secteur dotée d’une connexion de terre de protection.
17) Le dispositif de déconnexion doit rester facilement accessible.
18) La prise de courant doit être installée près de l’équipement et doit être facilement
accessible.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT REMOVE COVER
(OR BACK), NO USER-SERVICEABLE PARTS
INSIDE, REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage
within the product’s enclosure that may be of
sufcient magnitude to constitute a risk of electric
shock to persons.
This symbol is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
ATTENTION
RISQUE DE CHOC ELEC-
TRIQUE. NE PAS OUVRIR.
ATTENTION: POUR RÉDUIRE LE RISQUE DE
CHOC ÉLECTRIQUE, NE RETIREZ PAS LE CAPOT
(NI LARRIÈRE), AUCUNE PIÈCE RÉPARABLE
PAR L’UTILISATEUR, RÉFÉREZ L’ENTRETIEN AU
PERSONNEL DE SERVICE QUALIFIÉ.
Ce symbole est destiné à alerter l’utilisateur de la
présence d’une «tension dangereuse» non isolée
à l’intérieur de l’enceinte du produit qui peut être
d’une amplitude sufsante pour constituer un
risque de choc électrique pour les personnes.
Ce symbole est destiné à alerter l’utilisateur
de la présence d’instructions importantes
d’utilisation et de maintenance (entretien) dans la
documentation accompagnant l’appareil.
4
Please keep this manual for future reference.
Information in this manual is subject to change without prior notice.
FCC Information
This equipment has been tested and found to comply with limits for a class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and radiates radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
There is no guarantee that interference will not occur in a particular installation. If this equipment causes unacceptable
interference to radio and television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced Radio/TV technician for additional help.
Change or modication not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
WARNINGS
To reduce the risk of re, electrical shock and other injuries, keep these safety precautions in
mind when installing, using, and maintaining your Outdoor Display. The socket-outlet should be
installed near the equipment and be easily accessible. The display should be connected to a
grounded GFCI protected main socket outlet.
WARNING: If you manipulate against the recommended usage, serious injury or death to user may
result.
To protect against electric shock, do not immerse the power
cord, power plug, or product in water or other liquid.
Do not overload AC outlets or extension cords. Overloading can
cause re or electric shock.
Close adult supervision is necessary when any product is used
by or near children.
Do not operate any product with a damaged cord or plug
or operate it after the appliance malfunctions or has been
damaged in any manner.
Do not use the product close to any heat sources such as
radiators, heat registers, stoves, or other products that produce
heat.
Do not let the power cord come in contact with hot surfaces.
If you notice any smoke or scorched smell near the product,
unplug power cord and refer to qualied personnel for service
and/or repair.
Do not use or place any combustible or ammable substances
near the product.
To electrically disconnect the product, turn OFF the product,
then remove the electrical power plug from the outlet.
Do not place heavy articles on or step on the product.
Do not place the product on an unstable cart, stand, tripod or
table.
Do not use this product for other than intended use.
This Séura product is intended for use indoors and outdoors.
This product is water resistant. Do not immerse this product in
water.
For added safety during a lighting storm, or when this product
is left unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the antenna.
Specications of this product are subject to unannounced changes; this manual may thus not reect the current technical status.
FCC Warnings
5
S’il vous plaît garder ce manuel pour référence future.
Les informations contenues dans ce manuel sont sujettes à modication sans préavis.
Informations de la FCC
Cet équipement a été testé et déclaré conforme aux limites d’un appareil numérique de classe B , conformément à la partie 15 des règles de la
FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle.
Cet équipement génère , utilise et rayonne de l’énergie radiofréquence et , s’il n’est pas installé et utilisé conformément aux instructions, peut
causer des interférences nuisibles aux communications radio.
Il n’y a aucune garantie que des interférences ne se produiront pas dans une installation particulière. Si cet équipement provoque des interférences
inacceptables pour la radio et la télévision, ce qui peut être déterminé en mettant l’équipement hors tension, l’utilisateur est encouragé à essayer
de corriger l’interférence par une ou plusieurs des mesures suivantes.
• Réorienter ou déplacer l’antenne de réception.
• Augmenter la distance entre l’équipement et le récepteur.
• Connecter l’équipement à une sortie sur un circuit différent de celui sur lequel le récepteur est branché.
Consulter le revendeur ou un technicien radio / TV expérimenté pour de l’aide supplémentaire.
Tout changement ou modication non expressément approuvé par la partie responsable de la conformité peut annuler l’autorité de l’utilisateur à
utiliser l’équipement.
FCC Avertissements
AVERTISSEMENTS
Pour réduire le risque d’incendie, de choc électrique et d’autres blessures, garder ces consignes de sécurité à
l’esprit lors de l’installation, l’utilisation et l’entretien de votre télévision en plein air. La prise de courant doit être
installée près de l’équipement et être facilement accessible. Le téléviseur doit être relié à une prise de courant
avec terre protégé par disjoncteur différentiel.
ATTENTION: Si vous manipulez contre l’utilisation recommandée, des blessures graves ou la mort à l’utilisateur
peuvent en résulter.
Pour protéger contre les chocs électriques , ne pas immerger le cordon
d’alimentation , cordon d’alimentation , ou un produit dans l’eau ou tout
autre liquide.
Ne surchargez pas les prises de courant ou les rallonges. Une surcharge
peut causer un incendie ou un choc électrique.
Surveillance d’un adulte est nécessaire lorsque tout appareil est utilisé par
ou près des enfants.
Ne pas utiliser un produit avec un cordon ou une che détériorés
fonctionner après un mauvais fonctionnement de l’appareil ou a été
endommagé d’une manière quelconque.
Ne pas utiliser le produit à proximité de sources de chaleur telles que des
radiateurs , registres de chaleur , poêles ou autres produits qui produisent
de la chaleur.
Ne laissez pas le cordon d’alimentation entrer en contact avec des surfaces
chaudes.
Si vous remarquez de la fumée ou une odeur brûlée près du produit ,
débranchez le cordon d’alimentation et de vous référer à un personnel
qualié pour l’entretien et / ou réparation.
Ne pas utiliser ou placer des matières combustibles ou inammables à
proximité du produit.
Pour débrancher électriquement le produit , éteignez le produit , puis retirez
la che d’alimentation électrique de la prise.
Ne placez pas lourds articles ou étape sur le produit.
Ne pas placer le produit sur un chariot, un support, un trépied ou une table.
Ne pas utiliser ce produit pour d’autres ns que celles prévues.
Ce produit Séura est destiné à un usage intérieur et extérieur.
Ce produit est résistant à l’eau. Ne pas immerger le produit dans l’eau.
Pour plus de sécurité lors d’une tempête d’éclairage , ou quand le produit
est laissé sans surveillance et inutilisé pendant de longues périodes de
temps , débranchez-le de la prise murale et déconnectez l’antenne.
Spécications de ce produit sont sujettes à modications sans préavis; ce manuel ne peut donc pas tenir compte de l’état de la technique actuelle.
6
Warnings
When installing and during use of this product, basic safety precautions should always be followed to reduce the risk of re,
electric shock and/or injury to persons including the following:
Inspect the desired location for installation and be aware of all electrical wiring pathways, water pipes, gas lines, or other
potentially hazardous conditions that may exist to protect from accidental damage during creation of on-site conditions.
Ensure all required electrical specications are adhered to and have been installed by the appropriate individuals and are code
approved.
Ensure all framing requirements, if needed, have been completed to building code and pose no structural issues.
It is REQUIRED that this product is plugged into an electrical outlet protected by a Ground Fault Circuit Interrupter (GFCI) to
protect against electric shock, re, and/or injury. Failure to do so will void any warranty for this product.
Only qualied individuals should attempt to service the product. Removing covers can expose you to high voltage and other
dangerous conditions.
To protect against electric shock, do not immerse the power cord, power plug, or product in water or other liquid.
Do not overload AC outlets or extension cords. Overloading can cause re or electric shock.
Close adult supervision is necessary when any product is used by or near children.
Do not operate any product with a damaged cord or plug or operate it after the appliance malfunctions or has been damaged in
any manner.
• Do not let the power cord come in contact with hot surfaces.
To electrically disconnect the product, turn OFF the product, then remove the electrical power plug from the outlet.
• Do not use this product for other than intended use.
• This Séura product is intended for use indoors and outdoors.
This Séura product is water resistant. Do not immerse this product in water.
Retain this manual in a safe place for future reference.
Warnings:
Do not handle or remove your Outdoor Display from the packaging until it is ready to be installed.
To avoid damage to the Outdoor Display, only transport it in a vertical position.
It is highly recommended that at least two (2) persons assist in the installation of the Outdoor Display.
WARNING: READ ALL INSTRUCTIONS BEFORE
ATTEMPTING TO INSTALL OR SERVICE THIS PRODUCT.
7
Avertissements
Lors de linstallation et pendant l’utilisation de ce produit , les précautions de sécurité de base doivent toujours être suivies pour réduire le risque
dincendie , de choc électrique et / ou de blessures, notamment les suivantes :
• Inspecter l’emplacement souhaité pour linstallation et être conscient de toutes les voies de câblage électrique , les canalisations d’eau , conduites de
gaz , ou d’autres conditions potentiellement dangereuses qui peuvent exister pour protéger contre les dommages accidentels lors de la création des
conditions sur place.
• S’assurer que toutes les scications électriques requises sont respectées et ont été installés par les personnes appropriées et sont le code approuvé.
• S’assurer que toutes les exigences d’encadrement , si nécessaire , ont été achevés au code du bâtiment et ne posent pas de problèmes structurels.
• Il est nécessaire que ce produit est branché sur une prise électrique protée par un disjoncteur de fuite à la terre ( GFCI ) pour protéger contre les
chocs électriques , des incendies et / ou blessures. Ne pas le faire annulera toute garantie pour ce produit.
• Seules les personnes qualiées doivent tenter de réparer le produit. Le retrait des capots peut vous exposer à de hautes tensions et d’autres situations
dangereuses.
• Pour protéger contre les chocs électriques , ne pas immerger le cordon d’alimentation , cordon d’alimentation , ou un produit dans l’eau ou tout autre
liquide.
• Ne surchargez pas les prises de courant ou les rallonges. Une surcharge peut causer un incendie ou un choc électrique.
• Fermer surveillance d’un adulte est nécessaire lorsque tout appareil est utilisé par ou près des enfants.
• Ne pas utiliser un produit avec un cordon ou une che détériorés fonctionner après un mauvais fonctionnement de l’appareil ou a été endomma
d’une manière quelconque.
• Ne laissez pas le cordon d’alimentation entrer en contact avec des surfaces chaudes.
• Pour débrancher électriquement le produit , éteignez le produit , puis retirez la che d’alimentation électrique de la prise.
• Ne pas utiliser ce produit pour d’autres ns que celles prévues.
• Ce produit Séura est destiné à un usage intérieur et extérieur.
• Ce produit Séura est résistant à l’eau. Ne pas immerger le produit dans l’eau.
• Conservez ce manuel dans un endroit sûr pour référence ultérieure.
Avertissements:
Ne pas manipuler ou supprimer votre téléviseur exrieure de l’emballage jusqu’à ce quil soit prêt à être installé.
Pour éviter d’endommager la télévision en plein air, seul le transporter dans une position verticale.
Il est fortement recommandé qu’au moins deux (2) personnes aident à linstallation de la télévision en plein air.
AVERTISSEMENT: LIRE TOUTES LES INSTRUCTIONS AVANT
D’INSTALLER OU SERVICE CE PRODUIT.
8
Contents
BEFORE USE
Before Installation ................................................................................................................. 9
Installation Instructions ......................................................................................................10
Care and Maintenance .........................................................................................................10
INSTALLATION AND SETUP
Setup ......................................................................................................................................... 11
Connections ............................................................................................................................ 11
Remote Functions ................................................................................................................. 11
Display Control Functions ................................................................................................... 11
MENUS AND SETTINGS
On Screen Display Menu (OSD) .......................................................................................... 12
Control and Integration .......................................................................................................16
TROUBLESHOOTING AND TECHNICAL DETAILS
Troubleshooting .....................................................................................................................16
Technical Specications ......................................................................................................17
Product Limited Warranty ..................................................................................................18
IMPORTANT
The display should not be installed directly over a at
surface if heavy or driving rain may puddle and splash up
onto the lower portion of the display.
Direct sunlight on the display screen will heat internal
components and should be avoided.
IMPORTANT
Le téléviseur ne doit pas être installé directement sur une surface
plane, si de fortes pluies ou de conduite peut aque d’eau et
éclabousser sur la partie inférieure du téléviseur.
Lumière directe du soleil sur l’écran du téléviseur va chauffer les
composants internes et devrait être évitée.
9
Before Installation
Operation and Storage Requirements
The maximum ambient temperature range for operating the
device is -40°F to 140°F*. The screen is most optimally viewed
at ambient temperatures of 32°F to 122°F. Do not install the
device in the proximity of heat sources, such as heating pipes,
heaters, furnaces or other devices that radiate heat. Mount the
device in such a way that it is protected against moisture. To
prevent re or electric shock, never allow liquids to enter the
unit. The uninstalled product must be stored in dry and well-
ventilated rooms, without extreme temperature uctuations.
Heat sources and aggressive active substances may not be
stored in the proximity of the device. The required storage
temperature is -40°F to 140°F at an air humidity of 5 - 90% RH
non-condensing. The device must be stored in the complete
packaging, as delivered.
Installation
Have this product installed by qualied personnel only.
Whether installing your display indoors or outdoors, easy to use
standard mounting systems are available and can be specied
or recommended by Séura. Install the product in a way that it
is xed properly and take care that children are not exposed
to danger. Please take extra care during installation, avoid
impacts. Before cabling your monitor, check that the power is
off. To avoid any possibility of electric shock, always connect
your equipment to properly grounded outlets. Use of power
cords or adapters other than those provided may cause re or
malfunction. Place this product as close to the power socket as
possible. Leave enough space to insert and remove the power
plug on demand. Even if you power off the product with your
remote control, power is still present unless the power cord is
unplugged. The device may only be operated with the provided
power adapter. The rated voltage is indicated on the product
label. The device is factory-set to the optimal operating voltage
(see Technical Specication). Use only power cords and plugs
that are suitable for your local electrical outlets. Do not install
the power cord in a way that could obstruct a walkway. Ensure
furthermore that the cable is not clamped and that it cannot be
pulled out accidentally from the power adapter. Do not install
the power cords in the proximity of heating elements and
never place heavy items on the cable or power adapter. Do not
modify or repair the power cords.
CAUTION
Do not use any power cords or adapters other than those provided with
this product! Use of power cords or adapters other than those provided
with this product may cause re, electric shock or malfunction. The
individual components can be destroyed if the polarity is reversed or
an incorrect connection is used. A goodwill replacement is not possible
in such cases, since each device is submitted to meticulous quality
inspections prior to shipping. The connecting plugs must be attached
in such a way that the connector is held rmly. Have trained technical
personnel install the electrical facilities necessary for mounting. Connect
the power cord to a grounded GFCI (ground fault circuit interrupter)
protected outlet. Never cut or damage the power cord.
Please disconnect the device from the power outlet in the following
cases:
1. The device is out of use for a lengthy period.
2. The device malfunctions or displays other unusual features,
necessitating maintenance work.
3. During a thunderstorm.
Please plan the positioning of the power outlet and the source cables
before proceeding with the structural measures and positioning of the
Séura Outdoor Display.
AVERTISSEMENT
N’utilisez pas de cordons d’alimentation ou des adaptateurs autres que ceux fournis
avec ce produit! L’utilisation de cordons d’alimentation ou des adaptateurs autres
que ceux fournis avec ce produit peut causer un incendie , un choc électrique ou un
dysfonctionnement. Les composants individuels peuvent être détruits si la polarité
est inversée ou une connexion incorrecte est utilisée. Un remplacement de l’écart
d’acquisition n’est pas possible dans ce cas, étant donné que chaque appareil
est soumis à des contrôles de qualité minutieux avant l’expédition. Les prises de
raccordement doivent être xés de manière à ce que le connecteur est fermement
maintenu. Personnel technique ont été formés installent les installations électriques
nécessaires pour le montage. Branchez le cordon d’alimentation à une fuite à la
terre à la terre ( ground fault circuit de coupure ) de prise protégée. Ne jamais
couper ou endommager le cordon d’alimentation.
S’il vous plaît débrancher l’appareil de la prise de courant dans les cas suivants:
1. L’appareil est hors d’usage pendant une longue période.
2. Les dysfonctionnements de l’appareil ou d’autres caractéristiques inhabituelles
afche , nécessitant des travaux d’entretien.
3. Lors d’un orage.
S’il vous plaît planier le positionnement de la prise de courant et les câbles de la
source avant de procéder à des mesures structurelles et le positionnement de la
Télévision Séura extérieure.
NOTE
Make sure the power source circuits are properly grounded. Use the
supplied power cord in order to connect it to the power source. If your
installation requires a different power cord, be sure to use an ofcially
approved power cord displaying the mark of the safety agency that
denes the regulations for power cords in your country. Please consider
that the AC outlet for the power adapter is placed within reach of the
Séura Outdoor Display and should be easily accessible in case it needs
to be powered off.
Install the unit in an environment where the operating ambient
temperature will not exceed 60°C / 140°F. Ensure that your installation
complies with your national and local safety rules. Any servicing,
adjustment, maintenance or repair must be performed only by service-
trained personnel.
Ensure the power outlet is installed in an accessible location, to access
it easily in case of a defect.
The screen is most
optimally viewed at
ambient temperatures
of 32°F to 122 °F
*When the unit is used in temperatures below the ideal operating
temperature range, the picture may appear slightly delayed or
blurred. This is normal, and the picture will return to normal after
the temperature increases to the ideal operating temperature range.
Installation in sunlight reduces the maximum permitted air temperature.
10
Mounting Instructions
Séuras Outdoor Display is mounted using a standard VESA pattern on the back of the unit. VESA wall mounts are sold separately.
49" 400 x 400 mm M6 62 lbs
55" 400 x 400 mm M6 71 lbs
65" 400 x 400 mm M6 97 lbs
86" 600 x 400 mm M8 155 lbs
Séuras Outdoor Displays are heavier than indoor televisions. Ensure that the wall mount you choose is rated to hold the appropriate
weight. Also verify that the wall or mounting surface can support the necessary mounting hardware and weight of the display.
Clearance of 1-1/4" is required on the top, sides, and bottom of the product.
Power Input: 100 - 240 VAC, 50/60 Hz
Installation Environment
Avoid direct light or sun exposure, direct proximity to heat
sources. Do not place any heat sources such as radiators and
heat registers, etc. near the monitor. To reduce eye strain,
avoid installing the Séura Outdoor Display against a bright
background such as a window. Position the monitor at the
height of your eye level. Position the monitor directly in front
of you at a comfortable viewing distance.
Recommended Location
Séuras Ultra Bright weatherproof display has been designed to
perform outdoors. Even on a cloudy day, there is much more
light outdoors than inside your home. For best viewing, it is
recommended to install in a location where the TV is shaded, with
the screen oriented away from direct sunlight.
Séuras Outdoor Display has been engineered to perform trouble
free even if rain or snow falls directly on the unit. However, if you
wish to bring your Séura Outdoor Display indoors to avoid bad
weather; easy, standard mounting system will accommodate.
Sheltered location is recommended to reduce the frequency that
the display needs to be cleaned.
Installation Instructions
Care and Maintenance
Installation Steps
1. Verify that all cables and power supply are correctly prepared and located for the installation of the Outdoor Display.
2. Install VESA Wall Mount according to the manufacturer’s specications.
3. Make necessary power and input/output connections.
4. Install this Outdoor Display according to VESA Wall Mount manufacturer’s instructions.
Please follow the guidelines listed for proper display care and cleaning:
The panel surface can be cleaned with any conventional non-ammoniated cleaner. Care
should be taken to use only a soft lint-free cloth to avoid scratching the screen. Apply all
cleaners directly to the cloth and not the panel surface. Don’t saturate the panel surface
as residual cleaner may damage the panel.
Immediately remove solvent and dirt residues per the prescribed methods above with a
compatible cleaner or water.
IMPORTANT: To extend the performance and longevity of your display, it is highly
recommended to use a cover when the Outdoor Display is not in use.
11
Setup
Before using the device, please check the following contents of the box for completeness:
Outdoor Display
USER MANUAL
WWW.SEURA .COM
DISPLAY SIZES 49-INCH, 55-INCH, 65-INCH, 86-INCH
Storm Ultra Bright
Outdoor Display
MODEL NUMBERS
STM3-49-U
STM3-55-U
STM3-65-U
STM3-86-U
User ManualComponent
(YPbPr) Adapter
AC Cable Component Audio
Input Adapter
Remote Functions Display Control Functions
Power
Use VOLUME +/- to increase or
decrease volume level
CEC playback controls for use
with CEC compatible systems
MUTE turns on or off all audio output
Press MENU to launch On-Screen
Display menu
Use VOLUME +/- to increase or
decrease volume level
INPUT displays full input menu for
source content
Menu Controls: Use arrows and OK to
navigate menu and make selections
Press EXIT to close the On-Screen
Display menu
IR Remote
Control
Connections
Coaxial Digital
Audio Out
IR
Output
HDMI 1
HDMI 2
HDMI 3
Pass Through
Analog Audio
Line Out
LAN
HDBaseT
RS-232
IP Control
Optical Digital
Audio Out
Component
Video
Component
Audio
IR
Input
Display Port
Input
USB
(DC 5V 0.5A)
+12 VDC Out
(2A)
+5 VDC Out
(3.5A)
Channel functions not
available on displays
Power
Press MENU to launch On-Screen
Display menu
INPUT displays full input menu for
source content
12
On Screen Display Menu (OSD)
Using the remote: Using the built-in control panel:
1. Press MENU on your remote control to open
the OSD menu
2. Navigate within the OSD with the left/right
and up/down arrows
3. Change settings with the left/right or up/
down arrows
4. Go back one step with MENU
5. Conrm selection with the OK button
6. Press to EXIT the OSD menu.
1. Touch MENU on the control panel. The
control panel is located on the right side of
the display.
2. Navigate within the OSD and change setting
values by rotating the dial located on the
control panel.
3. Select or conrm menu options by pressing
the dial inwards.
4. Touch MENU when on the category
selection to exit the OSD menu.
Using the remote: Using the built-in control panel:
1. Press INPUT to display the Input Source list
2. Press the up or down arrows until the
desired Input Source is highlighted.
3. Press OK to conrm selection of the chosen
input.
4. Press to close the Input Source list without
selecting an alternative source
OR
If available, use the quick input controls on
the remote to directly designate the input
source.
1. Touch INPUT on the control panel. The
control panel is located on the right side of
the display.
2. Navigate within the input list by rotating
the dial located on the control panel.
3. Select the input by pressing the dial
inwards when the desired input is
highlighted.
OR
Touch MENU to exit the input menu without
changing inputs.
On Screen Display Menu (OSD)
In the on screen display menu (OSD) you can adapt the characteristics of your display based on personal preferences.
Input Source
Component
Display Port
HDMI1
HDMI2
HDMI3
HDBaseT
13
OSD (cont.)
Picture
The Picture menu offers options to enhance and rene the image
characteristics of your Séura Outdoor Display. These settings are based on
ambient conditions of illumination and personal preferences.
Adjustment options include:
Picture Mode
White Level
Black Level
Sharpness
Tint
Color
Gamma
Backlight
Apply to All Inputs
Reset
Picture Option
Customize the display image according to your preferences.
Adjustment options include:
Aspect Ratio
Noise Reduction
Smooth Motion
Audio Only
HDR
Color Filter
Input Color Format
RGB Color Range
White Balance
Customize the display image according to your preferences.
Adjustment options include:
Color Temperature
Method
Point
Red
Green
Blue
Apply to All Inputs
Reset
HDMI2 Resolution: 3840x2160@60Hz
Picture Aspect Ratio Stretch
Picture Option Noise Reduction Off
White Balance Smooth Motion
Audio Audio Only Off
Function HDR Auto
Timer Color Filter Off
HDMI-CEC Input Color Format Auto Select
Serial Control RGB Color Range Auto Select
Setup
HDMI2 Resolution: 3840x2160@60Hz
Picture Color Temperature Normal
Picture Option Method 2 Points
White Balance Point High
Audio Red 0
Function Green 0
Timer Blue 0
HDMI-CEC Apply to All Inputs
Serial Control Reset
Setup
HDMI2 Resolution: 3840x2160@60Hz
Picture Picture Mode (HDR) Standard
Picture Option White Level 50
White Balance Black Level 50
Audio Sharpness 50
Function Tint
Timer Color
HDMI-CEC Gamma 2.2
Serial Control Backlight User
Setup Apply to All Inputs
Reset
14
OSD (cont.)
Audio
Customize the display image according to your preferences.
Adjustment options include:
Balance
Speaker
AV Out
AV Out Volume
Function
Adjustment options include:
Backlight
User
Day
Twilight
Night
Cooling Control
Heating Control
Humidity Reduction
Timer
Adjustment options include:
Time
On Time
Input Source
Volume
Auto Power Off
Off Time
Time Format
Sleep Timer
HDMI2 Resolution: 3840x2160@60Hz
Picture Balance 0
Picture Option Speaker Off
White Balance AV Out Variable
Audio AV Out Volume 30
Function
Timer
HDMI-CEC
Serial Control
Setup
HDMI2 Resolution: 3840x2160@60Hz
Picture Backlight User
Picture Option User 100
White Balance Day 100
Audio Twilight 80
Function Night 60
Timer Cooling Control Always On
HDMI-CEC Heating Control Energy Saver
Serial Control Humidity Reduction Energy Saver
Setup
HDMI2 Resolution: 3840x2160@60Hz
Picture Time 01:34
Picture Option On Time 00:00 Off
White Balance Input Source Last
Audio Volume Last
Function Auto Power Off Off
Timer Off Time 00:00 Off
HDMI-CEC Time Format 12-hour
Serial Control Sleep Timer Off
Setup
15
OSD (cont.)
HDMI-CEC
Adjustment options include:
Control
Auto Power Off
Device Select
Connect
Menu
Information
Device Search
Serial Control
Adjustment options include:
Control Type
Connection
Lead Network Seing
DHCP
IP Address
Subnet Mask
Gateway
Apply Seings
MAC Address
RS232 Unit ID
Setup
Adjustment options include:
Language
Menu Transparency
OSD Timeout
Power Save Mode
No Signal Off
Power LED
Restore Default
Firmware Update
HDMI2 Resolution: 3840x2160@60Hz
Picture Control Enable
Picture Option Auto Power Off Off
White Balance Device Select
Audio Connect
Function Menu
Timer Information
HDMI-CEC Device Search
Serial Control
Setup
HDMI2 Resolution: 3840x2160@60Hz
Picture Language English
Picture Option Menu Transparency 20
White Balance OSD Timeout 10 Sec
Audio Power Save Mode Off
Function No Signal Off Off
Timer Power LED On
HDMI-CEC Restore Default
Serial Control Firmware Update
Setup
HDMI2 Resolution: 3840x2160@60Hz
Picture Control Type RS232
Picture Option Connection HDBaseT
White Balance Load Network Seing
Audio DHCP Off
Function IP Address XXX.XXX.XXX.XXX
Timer Subnet Mask XXX.XXX.XXX.XXX
HDMI-CEC Gateway XXX.XXX.XXX.XXX
Serial Control Apply Seings
Setup MAC Address XX:XX:XX:XX:XX:XX
RS232 Unit ID 0
16
Control and Integration
If the product is not working properly, please check the following troubleshooting hints before you contact customer service:
NOTE: If the above troubleshooting hints do not help you to nd a solution, please contact Séura.
For complete control documentation, please visit
www.seura.com/download-center
HDBaseT Instructions
RS232 Protocol
IR Commands
Category Pin-Out Diagrams
Compatible Control Drivers
For additional technical support, please contact Séura at 1-800-957-3872
during regular business hours: M-F 8:00 am - 4:30 pm, Central Time.
Scan here to visit the
download center on your
mobile device
Troubleshooting
Challenge Possible Solution
Will Not Power Up
Make sure to check that the AC power cable is connected to an outlet and the TV
Make sure that the power outlet is receiving power
Try pressing POWER button on the TV to make sure the problem is not the remote.
If the TV turns on, refer to ‘Remote control does not work’ troubleshooting guide.
Remote Control
Not Working
Make sure that there is known working batteries in the remote and in the correct polarity
Make sure there are no obstacles in between the IR receiver and the remote (ex. sunlight or tape)
Try pointing the remote directly at the TV from 5 feet away.
Signal Issue
Check cable connections to ensure they are connected.
Plug the video source directly into the display which will remove any potential issues associated with an extender or
matrix switch device. (if applicable)
Replace cables with known working cables.
Make sure the connected devices are powered ON.
Make sure that the TV’s source is on the correct INPUT.
Power cycle the video source device by unplugging the device and plugging the device back in.
For additional technical support, please contact Séura at 1-800-957-3872
during regular business hours: M-F 8:00 am - 4:30 pm, Central Time.
17
Information is subject to change without notice.
Technical Specications
1230 Ontario Road Green Bay, Wisconsin 54311
1-800-957-3872 contacts@seura.com
www.seura.com
55 INCH 4K UHD
Model: STM3-55-U
65 INCH 4K UHD
Model: STM3-65-U
86 INCH 4K UHD
Model: STM3-86-U
GENERAL
OPERATING TEMPERATURE RANGE -40°F to 140°F*
IDEAL OPERATING TEMPERATURE 32°F to 122°F
NON-OPERATING TEMPERATURE -40°F to 140°F
OPERATING HUMIDITY RANGE 10–90% RH, non-condensing
WATERPROOF RATING IP54 Minimum Rating
ISOTROPIC PREVENTION High TNI panels help to prevent screen blackout
VIDEO
DISPLAY RESOLUTION 3840 x 2160
FRAME RATE 60Hz
DISPLAY BRIGHTNESS 1000 cd/m2 800 cd/m2
ASPECT RATIO 16:9 16:9 16:9
CONTRAST RATIO Typical 1000:1 Typical 1100:1 Typical 1200:1
TUNER N/A N/A N /A
RESPONSE TIME 8 ms 8 ms 8 ms
VIEWING ANGLE 178° Horizontal/Vertical 178° Horizontal/Vertical 178° Horizontal/Vertical
POWER CONSUMPTION, DISPLAY
Standby: 3.5W
Heating: 200W
Normal: 175W Max
Standby: 3.5W
Heating: 200W
Normal: 200W Max
Standby: 3.5W
Heating: 345W
Normal: 425W Max
POWER CONSUMPTION, AC OUTLET Max 200W
DC OUTPUT Max 41.5W (12V 2A, 5V 3.5A)
INTEGRATION
HDMI 3
HDBaseT1 Port with LAN Out
COMPONENT YPbPr 1
DISPLAY PORT 1
LAN PORT 1 (IP Control)
RS-232C 1
IR INPUT 1
IR OUTPUT 1
Service Port 1 (USB Type)
DC OUT 12V-Max 2A, 5V-Max 3.5A
AC OUT 100-240V~, 50/60Hz, Max 200W Outlet
AUDIO
AUDIO: COMPONENT AUDIO INPUT 1
AUDIO: ANALOG LINE OUT 1
AUDIO: OPTICAL DIGITAL OUT 1
AUDIO: COAXIAL DIGITAL OUT 1
INTERNAL SPEAKERS N/A
INSTALLATION
PRODUCT DIMENSIONS 50.0" w x 29.1" h 58.6" w x 34.0" h 77.0" w x 44.4" h
PRODUCT DEPTH 3.7" 3.7" 3.7"
PRODUCT WEIGHT 70.5 lbs. 96.1 lbs. 154.3 lbs.
COMPARTMENT DIMENSIONS 11" w x 8" h x 1.5" d 11" w x 8" h x 1.5" d 11" w x 8" h x 1.5" d
VESA PATTERN 400 x 400mm 600 x 400mm
OTHER
CERTIFICATIONS AND COMPLIANCE FCC, MET
WARRANTY Séura warrants Outdoor Displays with respect to Séura’s labor, structure, assembly, display including remote, and power
supply for two (2) years.
REMOTE Séura Water Resistant IR Remote Control
* The screen is most optimally viewed at ambient temperatures of 32°F to 12F. Installation in sunlight reduces the maximum permitted air temperature.
IP Rating is an international standard that species the degree of protection against dust and water ingress. Séura Outdoor TVs are IP rated and designed to protect against rain, snow, ice, dust, and other outdoor elements.
Publish date: May 3, 2021. Information is subject to change without notice.
© 2021 Séura
Coaxial Digital
Audio Out
IR
Output
HDMI 1
HDMI 2
HDMI 3
Pass Through
LAN Input
Analog Audio
Line Out
LAN
HDBaseT
RS-232
IP Control
Optical Digital
Audio Out
Component
Video
Component
Audio
IR
Input
Display Port
Input
USB
(DC 5V 0.5A)
+12 VDC Out
(2A)
+5 VDC Out
(3.5A)
CONNECTIONS
18
Product Limited WarrantyProduct Limited Warranty LIMITED PRODUCT WARRANTY
1230 Ontario Road Green Bay, Wisconsin 54311
1-800-957-3872 contacts@seura.com
www.seura.com
Publish date: December 10, 2020. Information is subject to change without notice.
© 2020 Séura
The standard limited warranty policies of Séura, Inc. (“Séura”) shall apply to all equipment or
other goods (“Products”) at the time of sale to any authorized Séura distributor and/or product
reseller. These warranty policies may be modied by Séura from time to time. Copies of the
standard limited warranties then in effect for a particular Product will be made available upon
request and are also available on the Séura website at https://www.seura.com/warranty/. This
warranty is valid only with respect to Product sales in the U.S. and Canada.
If any Product fails to work or operate properly because of a defect in materials or workmanship,
Séura will, if notied of such defect within the applicable warranty period indicated below,
at its option, either: (a) repair the Product with new or refurbished parts onsite or at Séuras
factory, including Séura’s labor if applicable; or (b) replace the Product with a new or
refurbished Product; or (c) if repair or replacement is not commercially feasible, refund an
amount equal to a pro rata share of the current MSRP (as determined by the remainder of the
warranty period). The remedy chosen will be in good faith and at the discretion of Séura. In no
event will Séura be responsible for any costs related to installation and/or removal of Product.
Séura warrants its Products as set forth below, which warranty periods shall start and run
from the date of Séura’s sale of the Product:
Lighted Mirrors (excluding Select Lighted Mirrors) with respect to Séura’s labor, glass,
structure, and assembly for seven (7) years; electrical and LED light strips for ve
(5) years. Mirror technology with respect to Séura’s labor and parts including clocks,
nightlights, defoggers, and dimmers are covered for two (2) years.
Select Lighted Mirrors with respect to Séuras labor, glass, structure, and assembly for
one (1) year; electrical and LED light strips for three (3) years.
TV Mirrors with respect to Séura’s labor, glass, structure, and assembly for three (3)
years; TV including remote and power supply for two (2) years.
Lighted TV Mirrors with respect to Séura’s labor, glass, structure, and assembly for three
(3) years; electrical and LED light strips for ve (5) years. TV including remote and power
supply for two (2) years.
Indoor Waterproof TVs with respect to Séura’s labor, glass, structure, and assembly for
three (3) years; TV including remote and power supply for two (2) years.
Outdoor Displays with respect to Séura’s labor, structure, assembly, display including
remote, and power supply for two (2) years.
Indoor and Outdoor Mounts for two (2) years against defects in original hardware and/or
workmanship. Excludes corrosion or rust resulting from damaged, scratched or chipped
paint or other surfaces.
Outdoor Soundbars with respect to labor and parts for one (1) year.
Protective Display Covers for two (2) years against material and/or workmanship defects.
Decorative Frames for one (1) year.
Exceptions to Warranty: This warranty is valid only with respect to Product sales in the U.S.
and Canada. Séura does not warrant Products against defects arising out of, related to, or
caused by, whether totally or partially, and whether directly or indirectly, any of the following:
A. Failing to properly clean and maintain, any Product, part or component of a Product,
including, but not limited to, lters, front bezel, and other Product areas or components;
B. A Product’s extended use, including particularly, commercial applications, where a
Product is operating on average more than twelve (12) hours per day on a permanent or
extended periodic basis;
C. Circumstances, damage (including concealed damage) or other conditions occurring
during shipment of a Product or at any time after a Product leaves Séura’s facility
(including without limitation transport of the Product to or from Séura before or after
authorized service). Products must be packed properly using original packaging or Séura
replacement or pre-authorized packaging. Customer assumes all risk, and costs, including
transportation costs, while Product is in transit to or from Séura;
D. Circumstances, damage or other conditions occurring during unpacking and/or removal
of a Product from its original packaging, including the removal of protective material;
E. Improper, incorrect, or insufcient AC supply voltage to a Product;
F. Alterations, modications, including use of unauthorized mount, or changes to a Product
without Séura’s prior written authorization;
G. The incorporation of a Product into or within a product of a third party, without Séuras
prior written authorization;
H. A Product’s misuse, neglect use, abuse, or improper operation, including the failure to
follow a Product’s normal and ordinary operating instructions;
I. The effects of re, ood, lightning, electrical surges, water and other liquid inltration,
smoke, insect or animal infestation, sand, mud, chemicals, improper cleaning agents and
other substances not intended to come into contact with a Product, including any such
substances contact with a Product as the result of acts of God;
J. The improper or faulty installation, setup, or adjustment of a Product;
K. A Product’s repair, attempted repair, or total or partial disassembly by any party other
than a Séura authorized service representative;
L. When the Product occurs with pixel errors within the specied and permitted area. (For
more information about this, inquire directly with Séura regarding the Séura Pixel Policy.)
M. Corrosion that does not affect the performance of a Product or the reasonable cosmetic
appearance of a Product (including without limitation, scratches or other paint or nish
damage to a Product that lead to or are caused by, in part or in total, corrosion);
N. When a Lighted Mirror or Lighted TV Mirror using LEDs retains an overall brightness
greater than 70% of the original brightness, including cases whereas an individual LED
fails; and/or
O. Normal wear and tear on the Product.
Séura does not warrant that its Products will integrate with any third party products at
present or in the future. It is purchaser’s responsibility to test and verify compatibility. Further,
Séura does not warrant its software or programs, or any content downloaded after shipment.
It is the purchaser responsibility to take precautions to protect the product from malware,
viruses, data loss, and other potentially destructive programs.
Warranty Disqualiers. This Limited Warranty only extends to, and runs for the benet of,
the original purchaser of the Product and only covers a Product purchased new. All warranty
claims must be submitted together with original proof of purchase and any Product subject
to a warranty claim must retain its original Séura serial number. Séura reserves the right
to require any warranty claimant to produce the original purchase receipt or other original
purchase date proof as may be reasonably required by Séura to verify the Product’s warranty
eligibility. Séura shall have no liability with respect to Products whose serial number has been
removed, defaced, replaced, or otherwise tampered with in any manner. Séura reserves the
right to examine all failed product components and determine, in its sole discretion, whether
any product components are defective and covered under warranty.
LIMITATION OF LIABILITY. THE EXPRESS LIMITED WARRANTIES SET FORTH HEREIN ARE IN
LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR USE. SÉURA WILL NOT BE LIABLE FOR ANY DAMAGE TO OTHER
PROPERTY CAUSED BY ANY DEFECT IN THE PRODUCT, DAMAGES BASED ON INCONVENIENCE,
LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS
RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF THE CUSTOMER HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. SÉURA WILL NOT BE LIABLE FOR ANY LOSS, DAMAGE
OR LIABILITY OR ANY DIRECT, INCIDENTAL, INDIRECT, PUNITIVE, SPECIAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OR MISUSE OF A PRODUCT, OR ARISING OUT OF ANY
BREACH, BY THE PURCHASER OF A PRODUCT, OF THIS LIMITED WARRANTY. SÉURA SHALL
NOT BE LIABLE FOR ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY. SÉURA
SHALL NOT BE LIABLE FOR ANY VERBAL WARRANTY ASSURANCES MADE BY ANY EMPLOYEE
OR AUTHORIZED DISTRIBUTOR, RESELLER OR INSTALLER THAT CONFLICTS WITH OR
ENHANCES THE WRITTEN WARRANTY HEREIN. SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON HOW
LONG AN IMPLIED LIMITED WARRANTY LASTS, SO THE EXCLUSIONS MAY NOT APPLY TO A
PARTICULAR PURCHASER. NOTWITHSTANDING ANYTHING HEREIN TO THE CONTRARY, SÉURA’S
MAXIMUM AGGREGATE LIABILITY RELATED TO ANY WARRANTY CLAIM OR WITH RESPECT TO
A PRODUCT SHALL NOT EXCEED THE THEN CURRENT SÉURA WHOLESALE PRICE OF THE
SPECIFIC PRODUCT FROM WHICH THE CLAIM DERIVES.
NOTICE OF ANY WARRANTY CLAIM MUST BE RECEIVED BY SÉURA, IN WRITING, PRIOR TO
THE EXPIRATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. THE PRODUCT
WARRANTY APPLIES ONLY FOR THE PERIODS SET FORTH ABOVE.
Warranty Procedure. A warranty claimant must contact Séura at 920-857-9069 for a diagnostic.
Please have your Product receipt available. At that time, Séura will provide technical support
over the phone to attempt to x the problem. If unsuccessful, a Séura Representative will
determine if the Product will be serviced onsite, replaced, or returned to Séuras factory in
Green Bay, Wisconsin for repair. If Séura determines that the Product is not covered under
the warranty or damaged in shipping, Séura will notify and inform the purchaser of service
alternatives that are available on a fee basis.
Toll-Free Technical Support: Please call 1-800-957-3872 to speak with a Séura Technical
Support Representative. Séura Representatives are available Monday-Friday, 8:00am-4:30pm
Central Time.
Onsite Service: If Technical Support determines the problem may be xed onsite, a Séura
service agent will be scheduled within 24 hours to service the unit. A Séura representative
will work with the customer to schedule a convenient time for onsite service. Parts may
be sent to the customer’s location. Onsite service is available in the United States during
normal business hours Monday – Friday, unless other special circumstances exist and special
arrangements are made.
Factory Service: If Technical Support determines the Product must be sent back to Séuras
factory for repair, the customer must follow return instructions below. Séura will ship the
repaired Product to the authorized reseller, installer or customer’s address. This warranty
does not cover removal or installation costs of Products.
Advanced Replacement: If Technical Support determines the Product must be replaced,
Séura will ship a new Product to the authorized reseller, installer or customer’s address.
The customer must follow return instructions below to send the damaged Product back to
Séura’s factory. Credit card information will be collected before shipment of the replacement
Product. If Séura does not receive the original Product back within thirty (30) days of shipping
the replacement Product, the credit card on le will be charged at full MSRP. This warranty
does not cover removal or installation costs of Products.
Return Instructions: If return is necessary, Séura will issue a return goods authorization
(RGA) number and, if applicable, specic return and shipping instructions. A Product will
only be accepted for warranty claims if returned and shipped to Séura in the Product’s
original packaging materials. If original packaging is not available, please contact Séura to
receive authorized replacement packaging. Packages not bearing the issued returned goods
authorization (RGA) number will not be accepted by Séura and will be returned to sender.
In addition to the Product, the package must include the warranty claimant’s original sales
receipt for the purchase of the Product. All Product returns shall be received by Séura, at 1230
Ontario Road; Green Bay, WI 54311 with freight prepaid by the warranty claimant. Séura shall
not be responsible for, and the warranty claimant assumes and retains all such responsibility,
any damage or loss to or of the Product during shipment to and from Séura as the result of
a warranty claim.
Exclusive Remedy. This Limited Warranty sets forth the exclusive remedies of a warranty
claimant, and the exclusive liabilities and obligations of Séura, with respect to allegations of
a defective Product.
19163121.3
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and
any use of such marks by Séura is under license. Other trademarks and trade names are those of their
respective owners.
19
Publish date: May 05, 2021. Information is subject to change without notice.
© 2021 Séura
1230 Ontario Road Green Bay, Wisconsin 54311
1-800-957-3872 contacts@seura.com
www.seura.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Seura STM3-49-U Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues