Ergotron 24-388-009 Manuel utilisateur

Ergotron
Marque
Ergotron
Modèle
24-388-009
Catégorie
Chariots multimédia
Taper
Manuel utilisateur

Ce manuel convient également à

888-24-228-G-00 rev.C • 10/13
1 of 15
User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Nederlands
Benutzerhandbuch - Deutsch
Guida per l’utente - Italiano
Användarhandbok - svenska
:
www.ergotron.com
20" (508mm)
32" (824mm)
15-60 lbs (6.8-27.2 kg)*
WorkFit-B, LD
31.5"-48" *
(800-1219 mm)
< 51.25" *
(1302 mm)
0.80"-1.75" *
(20-44 mm)
0.80"-1.75"*
(20-44 mm)
23.5"-26.5" *
(597-673 mm)
< 36" *
(914 mm)
*Total weight of worksurface
and mounted equipment must
be < 60 lbs (27.2 kg).
Worksurface must meet ALL
dimensional and weight range
speci cation requirements.
WARNING! The addition of
accessories can negatively
impact the tip performance.
Wood Worksurface Weight Estimator
Worksurface
Thickness
Estimated Weight
per square foot
0.80” (20 mm) 2.9 lbs (1.32 kg)
1.25” (32 mm) 4.5 lbs (2.04 kg)
1.75” (44 mm) 6.3 lbs (2.86 kg)
Important! You will need to adjust this product
after installation is complete. Make sure all your
equipment is properly installed on the product
before attempting adjustments. This product
should move smoothly and easily through the
full range of motion and stay where you set it. If
movements are too easy or di cult or if product
does not stay in desired positions, follow the
adjustment instructions to create smooth and
easy movements. Depending on your product
and the adjustment, it may take many turns
to notice a di erence. Any time equipment is
added or removed from this product, resulting in
a change in the weight of the mounted load, you
should repeat these adjustment steps to ensure
safe and optimum operation.
RECTANGLE SHAPED WORKSURFACE
OTHER SHAPED WORKSURFACE
888-24-228-G-00 rev.C • 10/13
2 of 15
777-24-027-G-00
IMPACT HAZARD!
MOVING PARTS CAN CRUSH AND CUT.
Minimize Lift Tension BEFORE:
· Removing Mounted Equipment.
· Shipping Cart
· Storing Cart
To Minimize Lift Tension
1. Lower worksurface to lowest position.
2.
Turn adjustment nut at bottom of riser
counterclockwise until it stops (Adjustment
may require 40-60 revolutions).
Failure to heed this warning may result in serious
personal injury or property damage!
For More information and instructions refer to product
guide at www.ergotron.com or contact Ergotron
Customer Care at 1-800-888-8458. 822-634
14mm (9/16”)
WARNING
These symbols alert users of a safety condition that
demands attention. All users should be able to
recognize and understand the signi cance of the fol-
lowing Safety Hazards if encountered on the product
or within the documentation. Children who are not
able to recognize and respond appropriately to Safety
Alerts should not use this product without adult
supervision!
Hazard Symbols Review Symbol Signal Word Level of Hazard
NOTE A NOTE indicates important information that helps you
make better use of this product.
CAUTION
A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the
problem.
WARNING A WARNING indicates either potential for property dam-
age, personal injury, or death.
ELECTRICAL
An Electrical indicates an impending electrical hazard
which, if not avoided, may result in personal injury,  re
and/or death.
Safety
WARNING! TIPPING HAZARD!
When mounting accessories
to this product, they must stay
within the foot print. Do not
mount accessories past the
front and rear worksurface!
Failure to follow this warning
may result in equipment
damage and or personal injury.
888-24-228-G-00 rev.C • 10/13
3 of 15
827-178-00
Minimize Lift Strength BEFORE:
-Removing Mounted Equipment
-Shipping the Cart
-Storing the Cart
Install Stop Screw BEFORE:
-Shipping the Cart
-Storing the Cart
To Minimize Lift Strength
and Install Stop Screw:
1. With cart upright, lower
worksurface to lowest
position.
2. Turn adjustment nut at
bottom of riser
counter-clockwise until it
stops (Adjustment may
require 40-60 revolutions).
3. Install Stop Screw. Follow
Installation Instructions
provided with Cart.
Safety
WARNING! Stop screw is pre-installed in this product to secure it in the compressed position during
shipping and installation. DO NOT REMOVE THIS SCREW UNTIL INSTRUCTED TO DO SO IN THESE
INSTRUCTIONS. Make sure this screw is in place before starting installation. Failure to follow these
instructions may cause lift engine to expand rapidly and may result in equipment damage and or
personal injury. If the phillips head stop screw is not installed in this location, contact customer care
before continuing with installation.
DO NOT REMOVE SCREW UNTIL INSTRUCTED TO DO SO ON PAGE 11.
IMPORTANT!
Save this stop screw and instructions. Install stop screw when shipping or storing this
product. Failure to follow these instructions may cause lift engine to expand rapidly and
may result in equipment damage and or personal injury.
888-24-228-G-00 rev.C • 10/13
4 of 15
AB C
1
2
3
4
1x
1x 1x
2x
Ø 1/8" (3 mm)
Ø 5/32" (4 mm)
Ø 1/4" (6.5 mm)
Ø 15/32" (12 mm)
14mm
16x
4x
M2.9 x 7mm
M2.9 x 7mm
1x
ST3.9 x 16mm
#12-14 x 5/8”
TEMPLATE FOR
WorkFit-B, LD
Temporarily adhere Template to bottom
of worksurface and drill holes as specied.
Refer to installation instructions for
attachment of the brake release.
777-24-040-G-00 rev.A 04/13
7.913”
(201 mm)
2.381”
(60.5 mm)
7.086”
(180 mm)
1.30”
(33mm)
1.30”
(33mm)
1.57”
(40mm)
2.38”
(60.5 mm)
1.56” (39.5 mm)
0.22” (5.5 mm)
0.49” (12.5 mm)
1.57”
(40mm)
3.15”
(80 mm)
3.895”
(99 mm)
4.371”
(111 mm)
For RECTANGULAR
work surfaces:
Place this mark
13.15” (334mm)
from the front of
the worksurface
For NON-RECTANGULAR
work surfaces:
Place this mark
18.9” (480mm)
from the back of
the worksurface
6.141”
(156 mm)
2.243”
(57 mm)
3.937”
(100 mm)
3.543”
(90 mm)
3.268”
(83 mm)
3.15”
(80 mm)
16x Ø 4 mm x 10 mm Deep (Ø 5/32” x 3/8” Deep)
4x Ø 6.5 mm Through
1x Ø 12 mm Through
5x WorkFit PD Accessory Mounting Holes
1x Ø 3 mm x 10 mm Deep (Ø 1/8” x 3/8” Deep)
4.055”
(103 mm)
CENTER OF
MOUNTING
PLATE
FRONT OF
WORKSURFACE
3.189”
(81 mm)
4.657”
(118 mm)
1. Center this mark from side-to-side.
2. For RECTANGULAR work surfaces:
Place this mark 13.15” (334mm) from
the FRONT of the worksurface.
3. For NON-RECTANGULAR work surfaces:
Place this mark 18.9” (480mm) from the
BACK of the worksurface.
Components
Tools Needed
888-24-228-G-00 rev.C • 10/13
5 of 15
FRONT OF
WORKSURFACE
FRONT OF
WORKSURFACE
1
13 ⁄" (334 mm)
18 ⁄"
(480 mm)
Set-up Steps
Place template on bottom of work surface.
1. From side-to-side, align the center mark on the template with
the center of the work surface to ensure maximum stability.
2. From front-to-back, place the center mark on the template
13⁄" (334 mm) from the front of the worksurface.
Place template on bottom of work surface.
1. From side-to-side, align the center mark on the template with
the center of the work surface to ensure maximum stability.
2. From front-to-back, place the center mark on the template
18⁄" (480 mm) from the back of the worksurface.
Centered Centered
RECTANGLE SHAPED WORKSURFACE OTHER SHAPED WORKSURFACE
888-24-228-G-00 rev.C • 10/13
6 of 15
FRONT OF
WORKSURFACE
FRONT OF
WORKSURFACE
FRONT OF
WORKSURFACE
a b
3
2
1x
16x
3/8"
(10 mm)
5/32"
(4 mm)
Ø 5/32" (4 mm) Ø 1/8" (3 mm)
Set-up Steps
Mark holes with a center-punch, then drill holes into bottom of work surface.
Drill the 16x holes into bottom of work surface 3/8" (10 mm) deep.
TIP: To ensure proper depth, place a piece of tape on the drill bit
3/8" (10 mm) from the tip.
Drill this 1x hole into bottom of work surface 5/32" (4 mm) deep.
TIP: To ensure proper depth, place a piece of tape on the drill bit
5/32" (4 mm) from the tip.
Make sure template is located properly and that it is square with the worksurface.
Then tape the template in place.
888-24-228-G-00 rev.C • 10/13
7 of 15
FRONT OF
WORKSURFACE
FRONT OF
WORKSURFACE
FRONT OF
WORKSURFACE
cd
4
1x
4x
Ø 1/4" (6.5 mm) Ø 15/32" (12 mm)
Set-up Steps
ONLY if you plan to attach any of the WorkFit PD Accessories, mark holes with a center-punch, the drill those holes through the work surface.
TIP: Place something under the worksurface so you don't drill into the surface underneath when you drill these through holes.
Remove the template.
888-24-228-G-00 rev.C • 10/13
8 of 15
5
6
16x
1x
16x
M2.9 x 7mm
M2.9 x 7mm
1x
#12-14 x 5/8”
Set-up Steps
Front Edge of Worksurface
Front Edge of Worksurface
888-24-228-G-00 rev.C • 10/13
9 of 15
8
7a
a
b
b
5/16"
(8 mm)
Ø 1/8" (3 mm)
4x ST3.9 x 16mm
Set-up Steps
Drill holes into bottom of work surface 5/16" (8 mm) deep.
TIP: To ensure proper depth, place a piece of tape on the drill
bit 5/16" (8 mm) from the tip.
Place the Brake Handle on the work surface at desired location. For easy access, line
up the brake handle  ush with the front edge of the worksurface.
Mark holes to drill.
Attach Brake Handle.
888-24-228-G-00 rev.C • 10/13
10 of 15
a b
9
10
Set-up Steps
888-24-228-G-00 rev.C • 10/13
11 of 15
11a
bc
Set-up Steps
Remove the stop screw to allow the worksurface to raise and
lower before installing equipment.
After you remove the stop screw,
release the hand brake and move
the worksurface up to highest level.
After worksurface is raised to it's highest
level, Install all equipment.
IMPORTANT!
Save this stop screw and instructions. Install stop screw
when moving, shipping or storing this product. Failure
to follow these instructions may cause lift engine to
expand rapidly and may result in equipment damage
and or personal injury.
CAUTION! Make sure you leave 20”
(508mm) of slack in all equipment
cables to allow the worksurface to raise
up it’s full 20” (508mm). Failure to allow
enough slack in equipment cables may
cause cables to get pulled, equipment
to fall o desk and may result in
product damage and or personal
injury.
888-24-228-G-00 rev.C • 10/13
12 of 15
827-178-00
Minimize Lift Strength BEFORE:
-Removing Mounted Equipment
-Shipping the Cart
-Storing the Cart
Install Stop Screw BEFORE:
-Shipping the Cart
-Storing the Cart
To Minimize Lift Strength
and Install Stop Screw:
1. With cart upright, lower
worksurface to lowest
position.
2. Turn adjustment nut at
bottom of riser
counter-clockwise until it
stops (Adjustment may
require 40-60 revolutions).
3. Install Stop Screw. Follow
Installation Instructions
provided with Cart.
12
14mm
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make
sure all your equipment is properly installed on the product before attempting
adjustments. This product should move smoothly and easily through the full range of
motion and stay where you set it. If movements are too easy or di cult or if product
does not stay in desired positions, follow the adjustment instructions to create
smooth and easy movements. Depending on your product and the adjustment,
it may take many turns to notice a di erence. Any time equipment is added or
removed from this product, resulting in a change in the weight of the mounted load,
you should repeat these adjustment steps to ensure safe and optimum operation.
Increase Lift Strength
If the mounted weight is too heavy or this product does not stay up
when raised, then you'll need to increase Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or this product does not stay
down when lowered, then you'll need to decrease Lift Strength:
WARNING! DO NOT tip desk over to adjust. Only perform
adjustment while desk is upright. Failure to follow these
instructions may cause the lift engine to expand rapidly and
may result in equipment damage and or personal injury.
888-24-228-G-00 rev.C • 10/13
13 of 15
14mm
WARNING. Before removing mounted equipment (monitor, arm, stand CPU, etc.), from desk, or
to prepare for shipping or storing the desk it is extremely important to minimize the lift strength.
Failure to install these instructions may cause lift engine to expand rapidly and may result in
equipment damage and or personal injury.
WARNING! DO NOT tip desk over to adjust. Only perform
adjustment while desk is upright. Failure to follow these
instructions may cause the lift engine to expand rapidly and may
result in equipment damage and or personal injury.
1. Release the hand brake and move the worksurface up to highest level.
2. To minimize lift strength, turn adjustment bolt counter clockwise using a 14mm socket.
Keep adjusting until the wrench stops turning.
3. Once at minimum lift strength it is ok to remove mounted equipment.
APPENDIX A - Minimize Lift Strength
888-24-228-G-00 rev.C • 10/13
14 of 15
APPENDIX B - Inserting Stop Screw
WARNING. Before shipping or storing the desk, or in cases where the desk is placed on it’s back
or side*, it is extremely important that the stop screw be re-inserted. Failure to follow these
instructions may cause lift engine to expand rapidly and may result in equipment damage and
or personal injury.
1. Follow instructions in Appendix A to minimize lift strength.
2. Push the desk down past its lowest position.
3. While holding desk down, insert stop screw at the bottom of leg.
4. Once the stop screw has been
installed the desk can be shipped
or stored.
* Placing the desk on its back or side is not recommended.
888-24-228-G-00 rev.C • 10/13
15 of 15
Learn more about ergonomic computer use at:
Más información sobre el uso ergonómico de ordenadores:
Apprenez-en plus sur l’utilisation ergonomique d’un ordinateur sur:
Weitere Informationen zur ergonomischen Computernutzung  nden Sie unter:
Leer meer over ergonomisch computergebruik op:
Per ulteriori informazioni sull’uso ergonomico del computer:
www.computingcomfort.org
Height Position top of screen slightly below eye level.
Position keyboard at about elbow height with wrists  at.
Distance Position screen an arm's length from face—at least 20” (508mm).
Position keyboard close enough to create a 90˚ angle in elbow.
Angle Tilt screen to eliminate glare.
Tilt the keyboard back 10° so that your wrists remain  at.
Altura Coloque el borde superior de la pantalla ligeramente por debajo de la altura de sus ojos.
Coloque el teclado aproximadamente a la altura de los codos con las muñecas planas.
Distancia Coloque la pantalla a una distancia de un brazo desde la cara, esto es, unos 50 cm (20 pulgadas).
Coloque el teclado lo su cientemente cerca para que el codo forme un ángulo de 90º.
Ángulo Incline la pantalla para eliminar los re ejos.
Incline el teclado 10º hacia atrás para que las muñecas sigan en posición plana.
Hauteur Positionnez l’écran du haut légèrement en dessous du niveau du regard.
Positionnez le clavier à peu près à la même hauteur que vos coudes, pour que vos poignets soient à plat.
Distance Positionnez l’écran à un bras de distance de votre visage, à au moins 508 mm (20pouces).
Positionnez le clavier assez près pour que vos coudes forment un angle de 90°.
Angle Inclinez l’écran pour ne pas être ébloui.
Inclinez le clavier vers l’arrière de 10° pour que vos poignets soient à plat.
Höhe Positionieren Sie die obere Kante des Bildschirms knapp unter Augenhöhe.
Positionieren Sie die Tastatur bei  ach aufgelegten Handgelenken auf Ellenbogenhöhe.
Abstand
Positionieren Sie den Bildschirm mindestens eine Armlänge (50cm) von Ihrem Gesicht entfernt.
Positionieren Sie die Tastatur nahe genug, um einen Ellenbogenwinkel von 90˚ zu ermöglichen.
Winkel Neigen Sie den Bildschirm so, dass ein Spiegele ekt vermieden wird.
Neigen Sei die Tastatur um 10° nach hinten, sodass Ihre Handgelenke  ach au iegen.
Hoogte Zet de bovenkant van het scherm iets boven ooghoogte.
Plaats het toetsenbord op ongeveer ellebooghoogte met de polsen plat.
Afstand Plaats het scherm op een armlengte van uw gezicht — op ten minste 508 mm (20 in).
Zet uw toetsenbord zo dichtbij dat u een hoek van 90° in de ellebogen hebt.
Hoek Kantel het scherm om weerspiegeling te elimineren.
Kantel het toetsenbord 10° naar achteren, zodat uw polsen plat blijven liggen.
Altezza Posizionare la parte superiore dello schermo leggermente sotto il livello degli occhi.
Posizionare la tastiera circa all’altezza dei gomiti, in modo che i polsi siano piatti.
Distanza Posizionare lo schermo a un braccio di distanza dal viso, almeno a 20" (508 mm) di distanza.
Posizionare la tastiera a nché sia abbastanza vicina da costringere i gomiti a un angolo di 90˚.
Angolazione Inclinare lo schermo in modo da eliminare i ri essi.
Inclinare la tastiera indietro di 10° in modo che i polsi rimangano piatti.
°
To Reduce Fatigue
Breathe - Breathe deeply through your nose.
Blink - Blink often to avoid dry eyes.
Break • 2 to 3 minutes every 20 minutes
• 15 to 20 minutes every 2 hours.
Para reducir la fatiga
Respirar - Respire hondo por la nariz.
Parpadear - Parpadee a menudo para que no se sequen
los ojos.
Descansar • 2 o 3 minutos cada 20 minutos
• 15 o 20 minutos cada 2 horas.
Pour réduire la fatigue
Respirez - Respirez profondément par votre nez.
Clignez des yeux - Clignez souvent des yeux pour ne pas
avoir les yeux secs.
Faites des pauses • 2à 3minutes toutes les 20minutes
• 15à 20minutes toutes les 2heures.
Vermeiden von Ermüdungserscheinungen
Atmen - Atmen Sie tief durch die Nase ein und aus.
Blinzeln - Blinzeln Sie so oft wie möglich, um trockene
Augen zu vermeiden.
Pausen • Machen Sie alle 20Minuten eine Pause von
2-3Minuten
• Machen Sie alle 2Stunden eine Pause von 15-20Minuten.
Om vermoeidheid te verminderen
Ademen - Adem diep door uw neus in en uit.
Knipperen - Knipper regelmatig om droge ogen te vermi-
jden.
Pauzes nemen • 2 tot 3 minuten elke 20 minuten
• 15 tot 20 minuten elke 2 uur.
Per ridurre l’a aticamento
Respirazione - Respirare profondamente dal naso.
Battito delle palpebre - Battere spesso le palpebre per
evitare che gli occhi si asciughino.
Pause • Fare una pausa di 2 - 3 minuti ogni 20 minuti
• Fare una pausa di 15 - 20 minuti ogni 2 ore.
Set Your Workstation to Work For YOU!
Con gure su estación de trabajo para que trabaje para USTED.
Ajustez votre station de travail en fonction de VOS besoins!
Richten Sie Ihren Arbeitsplatz so ein, dass er für SIE arbeitet!
Stel uw werkstation zo in dat het voor U werkt!
Approntare la stazione di lavoro nella posizione ergonomica ottimale.
13
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Ergotron 24-388-009 Manuel utilisateur

Ergotron
Marque
Ergotron
Modèle
24-388-009
Catégorie
Chariots multimédia
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents