Honeywell MPIPKTSMF Guide d'installation

MPIPKTSMF
Honeywell
Marque
Honeywell
Modèle
MPIPKTSMF
Taper
Guide d'installation
English Quick Install Guide
The MAXPRO Intrusion Keypads are designed to provide a simple day-to-day interface with MPI Control Panels.
Each keypad connects to the IB2 communication bus.
Packing List
Keypad / 3xwall mounting screw / 1xtamper screw / 1xlid screw.
Parts (see illustrations)
AOpening for wiring (x3) GLid screw (x1)
BMounting screw holes (x4). Use the one at the
top. At the bottom, use the one in the middle or
the two at the edges, depending on your needs.
HTouch screen display
EIB2 bus connector ILEDindicators
FTamper screw (x1). Required for off-wall tamper
protection.
JCard reader
LED Colour Icon Function
Green Area is ready to arm: All zones in the keypad's home area are in their normal
state; the area is ready for arming.
Red
Area armed: The keypad's home area is armed.
EN To comply with EN standards, the red Area armed LEDis disabled in
Europe.
Green Power: Power is present.
Default PIN codes
The default PINcode length for EMEA installations is 6digits; for North American installations it is 4digits.
User 6-digit code 5-digit code 4-digit code
Installer 111222 11122 1112
Master 654321 65432 6543
Caution!
For security reasons, change the default codes as soonas possible from MAXPRO Cloud. For
instructions, see the MAXPRO Cloud Configuration Guide (EMEA version doc. no. 800-24096-1;
North America version doc no. 800-24096).
Programming
On the keypad: set display brightness and sound level: log on, tap Menu >Keypad settings >General settings.
All additional security settings are configured inMAXPRO Cloud. For details, see the MAXPRO Cloud
Configuration Guide (EMEA version doc. no. 800-24096-1; North America version doc no. 800-24096).
For daily use of the keypad, see the MAXPRO Intrusion User Guide (EMEA version doc. no. 800-23041-1; North
America version doc. no. 800-23041). The user guide is available with the control panel, and you can find the latest
version online.
Refer to the installation instructions for the control panel that this device is used with, for details
regarding limitations of the entire alarm system.
For details, see the MAXPRO Intrusion Installation Guide (EMEA version doc. no. 800-23044-1; North America
version doc. no. 800-23044).
Specifications
Input voltage 13.8VDC nominal (10–14.5VDC)
Current, idle MPIKTSMF: 100mA / MPIKTSPRX: 75mA
Current, max. (display and
buzzer on)
MPIKTSMF: 130mA / MPIKTSPRX: 110mA
Sounder Full Power, -3dB, -6dB, and -9dB (85dB at 10cm/4in)
MPIKTSMF card types MIFARE (Classic 32-bit, DESFire 56-bit (EU only)); reading CSN only
EM4102 ASK 125kHz; up to 40bits
MPIKTSPRX card types EM4102 ASK 125kHz; up to 40bits
Operating temperature –10 to +50°C / 14–122°F; Indoor use only
Humidity Max. 93% RH non-condensing
Ingress and impact protection IP42 (EN60529:1992+A2:2013) / IK06 (EN62262:2002)
Dimensions (WxHxD) 8.45cm x 13.96cm x 4.01cm / 3.33in x 5.55in x 1.58in
Weight 169g / 5.96oz
Ancillary Control Equipment
(ACE)
TypeB
Options MPIKW1: MAXPRO Intrusion Keypad Wall Mounting Plate
Environmental Information (EU)
This symbol on our product shows a crossed-out "wheelie-bin" as required by law regarding the Waste
of Electrical and Electronic Equipment (WEEE) disposal. This indicates your responsibility to contribute
in saving the environment by proper disposal of this Waste i.e. Do not dispose of this product with
your other wastes. To know the right disposal mechanism please check the applicable law.
Compliance (EU)
This product is suitable for use in systems designed to comply with PD6662:2017.
This product has been tested for compliance by BRE Global Ltd. UKto:
EN50131-3:2009 Grade3, Environmental ClassII.
Note: The MPIKW1 keypad wall mounting plate is not part of certification.
Product Certification (EU)
Cert/LPCB ref. 787a
EN50131-3:2009
RSS Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference. (2) This device must accept any interference, including interference that may cause
undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes: 1.L’appareil ne doit pas produire de brouillage; 2.L’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
For more information, updates and latest versions, and other languages:
800-23150 Rev. A6 draft_03 August 2020
Honeywell Commercial Security
Copyright © 2020 Honeywell International Inc.
www.security.honeywell.com
EMEA:
Aston Fields Road
Whitehouse Industrial Estate
Runcorn
Cheshire
WA7 3DL
United Kingdom
Tel: +44 (0)8448 000 235
North America:
715Peachtree Street NE
Atlanta, GA30308
USA
Quick Install Guide MAXPRO Intrusion Keypads
MPIPKTSMF, MPIKTSPRX
1
A
B
A
E
A
F
B
2
D C – +
IB2
3
G
4
H
I
J
  • Page 1 1
  • Page 2 2

Honeywell MPIPKTSMF Guide d'installation

MPIPKTSMF
Honeywell
Marque
Honeywell
Modèle
MPIPKTSMF
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents