W11
184585B
W11184905A-SP
If you have any problems or questions, visit us at www.maytag.com
Pour tout problème ou question, consulter www.maytag.ca
Use and Care Guide
Guide d’utilisation et d’entretien
ELECTRONIC DRYER
SÉCHEUSE ÉLECTRONIQUE
Para obtener acceso
al Manual de uso y
cuidado en español, o para
obtener información adicional
acerca de su producto, visite:
www.maytag.com.
2
DRYER SAFETY
TABLE OF CONTENTS
DRYER SAFETY .......................................................................................2
ACCESSORIES ....................................................................................... 4
CHECK YOUR VENT SYSTEM FOR GOOD AIRFLOW .............5
CONTROL PANEL AND FEATURES .................................................6
CYCLE GUIDE .........................................................................................8
USING YOUR DRYER .........................................................................10
ADDITIONAL FEATURES .................................................................. 12
DRYER CARE ........................................................................................ 12
TROUBLESHOOTING ........................................................................15
WARRANTY ........................................................................................... 18
ASSISTANCE OR SERVICE ............................................ Back Cover
TABLE DES MATIÈRES
SÉCURITÉ DE LA SÉCHEUSE ........................................................ 19
ACCESSOIRES .................................................................................... 21
VÉRIFICATION D’UNE CIRCULATION D’AIR ADÉQUATE
POUR LE SYSTÈME D’ÉVACUATION ............................................ 22
TABLEAU DE COMMANDE ET CARACTÉRISTIQUES ............ 23
GUIDE DES PROGRAMMES .......................................................... 25
UTILISATION DE LA SÉCHEUSE .................................................... 27
CARACTÉRISTIQUES SUPPLÉMENTAIRES .............................. 29
ENTRETIEN DE LA SÉCHEUSE ...................................................... 29
DÉPANNAGE ......................................................................................... 32
GARANTIE .............................................................................................. 36
ASSISTANCE OU SERVICE .................................Couverture arrière
3
In the State of Massachusetts, the following installation instructions apply:
■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by
the State of Massachusetts.
■ Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.
■ A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury, death, or property
damage.
Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this
or any other appliance.
–
–
WHAT TO DO IF YOU SMELL GAS:
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
•
If you cannot reach your gas supplier, call the re department.
–
Installation and service must be performed by a qualied installer, service agency, or
the gas supplier.
•
Clear the room, building, or area of all occupants.
4
ACCESSORIES
15" Pedestal
Color-matched pedestal raises the dryer to
a more comfortable working height. The large
drawer provides convenient storage.
Stack Kit
If space is at a premium, the stack kit allows
the dryer to be installed on top of the washer.
Drying Rack
The Drying Rack provides a
stationary drying surface for items
such as sweaters and tennis shoes.
See the “Additional Features”
section for more information.
Customize your new dryer with the following genuine
Maytag accessories. For more information on options and
ordering, contact your dealer, call us at 1-800-344-1274,
or visit: www.maytag.com/accessories.
In Canada, call 1-800-688-2002 or visit: www.maytag.ca
INSTALLATION & MAINTENANCE
ACCESSORIES
FACTORY CERTIFIED PARTS – these three
words represent quality parts and accessories
designed specically for your appliance.
Time tested engineering that meets
our strict quality specications.
FACTORY CERTIFIED PARTS
Accessories designed for your appliance:
5
CHECK YOUR VENT SYSTEM FOR GOOD AIRFLOW
Good airflow
Along with heat, dryers require good airflow to efficiently
dry laundry. Proper venting will reduce your drying times and
improve your energy savings. See Installation Instructions.
The venting system attached to the dryer plays a big role
in good airflow.
Service calls caused by improper venting are not covered by
the warranty and will be paid by the customer, regardless of
who installed the dryer.
Maintain good airflow by:
n
Cleaning your lint screen before each load.
n
Replacing plastic or foil vent material
with 4" (102 mm) diameter heavy, rigid
vent material.
Good
Better
n
Using the shortest length of vent possible.
n
Using no more than four 90° elbows in a vent system.
Each bend and curve reduces airflow.
n
Removing lint and debris from the exhaust hood.
n
Removing lint from the entire length of the vent system
at least every 2 years. When cleaning is complete, be
sure to follow the Installation Instructions supplied with
your dryer for final product check.
n
Clearing away items from the front of the dryer.
Use Sensor Cycles for optimal fabric care and energy savings
Use the Sensor Cycles to provide the optimal fabric care from the dryer. During Sensor Cycles, drying air temperature and moisture
level are sensed in the load. This sensing occurs throughout the drying cycle and the dryer shuts off when the load reaches the selected
dryness. You can also use the Extra Power option with Sensor Cycles for harder-to-dry or mixed loads.
With Timed Dry, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to overdrying.
Use Timed Dry for the occasional damp load that needs a little more drying time or when using the drying rack.
Tips for getting the best performance from your steam dryer (on some models)
n
Results may vary depending on fabric. 100% cotton
garments with wrinkle-free finish may yield better results than
those without. 100% cotton items may require additional
touching up after cycles that use steam.
n
Use of a fabric softener sheet is not recommended with cycles
that use steam. It may cause temporary staining on clothes.
n
Cycles that use steam are not recommended for items that
have been starched. Wash any starched or new garments
prior to using cycles that use steam.
n The Steam Refresh cycle is best for smoothing out wrinkles
and reducing odors from loads consisting of dry items of
wrinkle-free cotton, cotton-polyester blend, common knits,
and synthetics.
6
:
AirDry
High
Less
More
Off
Sensing
Cool Down
Check Vent
Wet
Damp
EXTRA POWER
:
AirDry
High
Less
More
Off
+Steam
Sensing
Cool Down
Check Vent
Wet
Damp
EXTRA POWER
CONTROL PANEL AND FEATURES
Not all features and cycles are available on all models.
NOTE: The control panel features a sensitive surface that responds
to a light touch of your finger. To ensure your selections are registered,
touch the control panel with your fingertip, not your fingernail. When
selecting a setting or option, simply touch its name.
POWER/CANCEL
Touch to turn the dryer on and off. Touch to stop/cancel
a cycle at any time.
CYCLE CONTROL KNOB
Turn the knob to select a cycle for your laundry load. Sensor
Cycles are Bulky Items, Towels, Sanitize (steam models only),
Whites, Heavy Duty, Regular, Delicates, Wrinkle Control,
and Normal. Timed Cycles are Timed Dry and Quick Dry.
The Steam Cycle (on some models) is Steam Refresh.
See “Cycle Guide” for detailed descriptions of cycles.
The Cycle Control Knob can also be pressed to activate
the Extra Power option for harder-to-dry loads. See the
“Options” section for more information.
START/PAUSE
Touch and hold until the LED counts down “3-2-1” and the
dryer starts, or touch once while a cycle is in process to
pause it.
1
2
3
3
2
1
4
5
LED DISPLAY AND SETTINGS
When you select a cycle, its settings will light up and the
Estimated Cycle Time (for Sensor Cycles) or actual time
remaining (for Timed Cycles) will be displayed.
See “Cycle Guide” for available settings on each cycle.
Not all settings are available with all cycles.
More Time/Less Time
Touch MORE TIME or LESS TIME with Timed Cycles
to increase or decrease the length of a Timed Dry
or Quick Dry cycle.
Temp
When using any cycle except Sanitize, you may select
a dry temperature based on the type of load you are
drying. Use the warmest setting safe for the garments
in the load. Follow garment label instructions.
Dryness
When using Sensor Cycles (except for the Sanitize
cycle), you may select a Dryness level based on the
type of load you are drying.
NOTE: Dryness is for use with Sensor Cycles only.
4
3
2
14
5
Steam models
Non-steam models
7
CYCLE STATUS INDICATORS
The Cycle Status Indicators show the progress of a cycle.
Not all indicators are available on all models.
Sensing
The Sensing indicator will light during Sensor Cycles to
indicate that the moisture sensor on the dryer is operating.
This indicator will not light during Timed Cycles or options
such as Wrinkle Prevent.
Wet
The load is still wet and/or the cycle just started.
Damp
The load still has moisture remaining, a good point
in the cycle to remove a garment to air dry or iron.
Cool Down
The dryer has finished drying with heat and is now tumbling
the load without heat to cool it down and reduce wrinkling.
Check Vent
The Check Vent indicator is a feature available for Sensor
Cycles only. This indicator will show the status of airflow
through the dryer and the dryer vent system for the dryer’s
life. During the sensing phase at the beginning of the cycle,
the Check Vent light will come on if a blocked vent or low
airflow issue is detected. This light will stay on for the entire
cycle. Should the Check Vent light illuminate, refer to the
“Troubleshooting” section for potential solutions to the issue.
The light will be cleared upon completion of the cycle, touching
Power, or opening the door. It will continue to illuminate during
the cycle unless the root cause is resolved.
NOTE: The dryer will continue to operate even while the
indicator is lit, but poor airflow can impact dry times and overall
performance. For more information on maintaining good airflow,
see “Check Your Vent System for Good Airflow.” If there are
other error issues during a cycle, the Check Vent indicator will
not light up. See the “Troubleshooting” section.
This will indicate that the selected cycle has ended and the
load may be removed from the dryer. If Wrinkle Prevent has
been selected, the dryer may continue to tumble the load,
even if “End” is showing in the display.
Control Lock
This will illuminate when the controls are locked.
NOTE: The Control Lock function may be enabled when
recovering from a power failure. To unlock the control, touch
and hold CONTROL LOCK for at least 3 seconds.
6
:
Sensing
Cool Down
Check Vent
Wet
Damp
Appearance may vary.
OPTIONS
Use to select available options for your dryer. Not all cycles
and options are available on all models.
Wrinkle Prevent
If you will be unable to remove a load immediately,
touch WRINKLE PREVENT to add up to 150 minutes
of periodic tumbling to help reduce wrinkling. On steam
models, on some cycles, you may select the “+Steam”
setting to add a short steam cycle after 60 minutes
to help smooth out wrinkles.
Reduce Static (steam models only)
Touch to add the Reduce Static option to selected
Sensor Cycles (see “Cycle Guide”). The dryer will
automatically tumble, pause, and introduce a small amount
of moisture into the load to help reduce static. This option
adds approximately 3 minutes to the total cycle time.
Steam (steam models only)
Steam adds steam to the end of certain Sensor Cycles
to help smooth wrinkles. It is not available on Sanitize,
Delicates, Steam Refresh, or Timed Cycles (Timed Dry,
Quick Dry). Steam can be used with High or Medium heat
settings. This option adds approximately 15 minutes to
the total cycle time.
Cycle Signal
Use this to turn the signal indicating the end of a drying
cycle on or off. Touch CYCLE SIGNAL to turn sounds
on or off.
Control Lock
Use to lock the controls of the dryer and avoid
an accidental change in cycle options or preferences
during a drying cycle. Touch and hold CONTROL LOCK
for 3 seconds to lock or unlock the controls of the dryer.
During this time, the LED Display will count down “3-2-1.”
Once the controls are locked, the Control Lock icon
will illuminate.
NOTE: The Control Lock function may be enabled when
recovering from a power failure. To unlock the control,
touch and hold CONTROL LOCK for at least 3 seconds.
Extra Power
The Extra Power option can be used with both Sensor
and Timed Dry Cycles. Press the Cycle Control Knob
to activate the Extra Power option, which provides an
additional 10 minutes of cycle time (including additional
heat and tumbling, where applicable). When Extra Power
is activated, the Cycle Control Knob will illuminate and
the estimated time remaining on the display will show an
additional 10 minutes.
5
8
CYCLE GUIDE — SENSOR CYCLES
Settings and options shown in bold are default settings for that cycle.
If settings are changed, the new settings will be remembered. If there is a power failure, settings will return to the default.
Not all features and cycles are available on all models.
Not all settings and options are available on each cycle.
Heavyweight items Heavy Duty High More
1:06
Wrinkle Prevent
†
Offers stepped drying starting
such as towels or Medium Normal Reduce Static* with High heat followed by Medium
heavy work clothes Low Less Steam* heat for enhanced fabric care
Cycle Signal and energy savings.
Extra Power
Work clothes, casual Normal High More
1:27
Wrinkle Prevent
†
Uses Medium heat to dry large
wear, mixed cottons, Medium Normal Reduce Static* loads of mixed fabrics and items.
sheets, corduroys Low Less Steam* Normal is the most effi cient cycle.
Cycle Signal
Extra Power
Shirts, blouses, Wrinkle Control High More
47
Wrinkle Prevent
†
Uses a stepped drying temperature
permanent press, Medium Normal Reduce Static* from Medium to Low for improved
synthetics, Low Less Steam* moisture removal and enhanced
lightweight items Cycle Signal fabric care.
Extra Power
Undergarments, Delicates High More
35
Wrinkle Prevent Uses Low heat to gently dry
blouses, lingerie, Medium Normal Reduce Static* delicate items.
performance wear Low Less Cycle Signal
Extra Power
Large loads Sanitize High More
1:42
Wrinkle Prevent
†
This is a long cycle with High heat,
of heavyweight Extra Power which has been proven to reduce
items household bacteria. This cycle is not
recommended for all fabrics. Use for
large loads of heavyweight fabrics.
Jackets, comforters, Bulky Items High More
59
Wrinkle Prevent
†
Use for drying large, bulky items;
pillows Medium Normal Reduce Static* do not overfi ll dryer drum. Partway
Low Less Steam* through the cycle, the signal will
Cycle Signal sound for 2 minutes to indicate
Extra Power when it is time to rearrange items
for optimal drying.
Shirts, blouses, Regular High More
57
Wrinkle Prevent
†
Uses Medium heat to dry large
permanent press, Medium Normal Reduce Static* loads of mixed fabrics and items.
synthetics, Low Less Steam*
lightweight items Cycle Signal
Extra Power
White, sturdy items Whites High More Wrinkle Prevent
†
Uses High heat to dry large loads
Medium Normal Reduce Static* of white, sturdy fabrics and items.
Low Less Steam*
Cycle Signal
Extra Power
Large loads Towels High More Wrinkle Prevent
†
This is a long cycle with High heat.
of cotton towels, Medium Normal Reduce Static* This cycle is not recommended for
heavyweight items Low Less Steam* all fabrics. Use for large loads of
Cycle Signal heavyweight fabrics.
Extra Power
Items to dry: Cycle:
Drying
Temperature:
Dryness
Level:
Default
Time:
Available
Options:
Cycle Details:
Load Size Recommendations
For best results, follow the wet load size recommendations noted
for each cycle.
Small load: Fill the dryer drum with 3–4 items, not more
than 1/4 full.
Medium load: Fill the dryer drum up to about 1/2 full.
Large load: Fill the dryer drum up to about 3/4 full.
Do not tightly pack. Items need to tumble freely.
Use Sensor Cycles for better fabric care and energy savings
The dryer senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness level.
The default times mentioned below are for reference only. The exact cycle times will vary, depending on the load size and type.
†
On steam models, you may select the “+Steam” setting to add a short steam cycle after 60 minutes. This is available only with High and Medium drying
temperature settings.
*On steam models only.
5
2
1:
07
9
CYCLE GUIDE — TIMED CYCLES
Settings and options shown in bold are default settings for that cycle.
If settings are changed, the new settings will be remembered (except on Quick Dry). If there is a power failure, settings will return
to the default.
Not all features and cycles are available on all models.
Not all settings and options are available on each cycle.
Any load Timed Dry High 40 Wrinkle Prevent
†
Use to dry items to a damp level for items that do
NOTE: Select Medium Extra Power not require an entire drying cycle. Select a drying
AirDry to dry foam, Low temperature based on the type of fabrics in your
rubber, plastic, AirDry load. If you are unsure of the temperature to select
or heat-sensitive for a load, select the lower setting rather than the
fabrics. higher setting.
Small loads Quick Dry High 15 Wrinkle Prevent
†
For small loads of 3–4 items.
and sportswear Medium
Low
AirDry
Items to dry:
Cycle:
Drying
Temperature:
Default
Time:
Available
Options:
Cycle Details:
CYCLE GUIDE — STEAM CYCLE (on some models)
Settings and options shown in bold are default settings for that cycle.
Not all settings and options are available on each cycle.
Steam cycles are designed for use with dry loads to loosen wrinkles, reduce odors, and refresh fabrics.
Load Size Recommendations
For best results, follow the load size recommendations noted
for each cycle.
Small load: Fill the dryer drum with 3–4 items, not more
than 1/4 full.
Medium load: Fill the dryer drum up to about 1/2 full.
Large load: Fill the dryer drum up to about 3/4 full.
Do not overload. Items need to tumble freely.
Shirts, blouses, Steam Refresh High
20
Wrinkle Prevent Use to reduce light wrinkles from loads left in the
and slacks dryer too long. Do not add dryer sheets.
Items
to refresh:
Cycle:
Drying
Temperature:
Default
Time:
Available
Options:
Cycle Details:
Adjusting drying time on Timed Cycles
When you select a Timed
Cycle, the time appears in
the display. Use More Time
and Less Time to increase
or decrease the time
in 5-minute increments.
The maximum dry time
is 150 minutes.
Selecting the Drying Temperature
A High heat setting may be used for drying heavyweight items
such as towels and work clothes.
A Low to Medium heat setting may be used for drying
mediumweight items such as sheets, blouses, dresses,
underwear, permanent press fabrics, and some knits.
Use a no heat (AirDry) setting for foam, rubber, plastic,
or heat-sensitive fabrics.
Line dry bonded or laminated fabrics.
NOTE: If you have questions about drying temperatures
for various loads, refer to the care label directions.
†
On steam models, you may select the “+Steam” setting to add a short steam cycle after 60 minutes. This is available only with High and Medium drying
temperature settings.
AirDry
High
Less
More
Off
+Steam
Sensing
Cool Down
Check Vent
Wet
Damp
Appearance may vary.
NOTE: Government energy certifi cations for this model were based on the Normal Cycle, Highest Temperature Setting, Normal Dryness
Level. The as-shipped defaults were the same as the Government Energy Certifi cation Settings except the Default Temperature Setting
of Medium was adjusted to the Highest Temperature Setting.
10
USING YOUR DRYER
1. Clean the lint screen
Clean the lint screen before each load. Pull the lint screen straight
up. Roll lint off the screen with your fi ngers. Do not rinse or wash
screen to remove lint. Wet lint is hard to remove. Push the lint
screen fi rmly back into place.
For additional cleaning information, see “Dryer Care.”
2. Load the dryer
Open the door by pulling on the handle. Place laundry in the dryer.
Add a dryer sheet to wet load if desired. Close the door.
IMPORTANT: Do not tightly pack the dryer. Items need to tumble
freely. Tightly packing can lead to poor drying performance and may
increase wrinkling and tangling.
WARNING: To reduce the risk of fi re, electric shock, or injury to
persons, read the Important Safety Instructions before operating
this appliance.
3. Touch POWER/CANCEL
Touch POWER/CANCEL to turn on the dryer.
4. Select the desired cycle
Select the desired cycle for your load. See the “Cycle Guide”
for more information about each cycle. Not all cycles are on
all models. Press the Cycle Control Knob to activate the Extra
Power option, which provides an additional 10 minutes of cycle
time (including additional heat and tumbling, where applicable).
Appearance may vary.
Appearance may vary.
:
AirDry
High
Less
More
Off
+Steam
Sensing
Cool Down
Check Vent
Wet
Damp
EXTRA POWER
:
AirDry
High
Less
More
Off
+Steam
Sensing
Cool Down
Check Vent
Wet
Damp
EXTRA POWER
11
Promptly remove garments after cycle has completed to
reduce wrinkling. If you will be unable to remove the load
promptly, select the Wrinkle Prevent option.
7. Touch and hold START/PAUSE
to begin cycle
Touch and hold START/PAUSE until the display counts down
“3-2-1” and the dryer starts.
8. Remove garments promptly
after cycle is fi nished
5. Adjust cycle settings, if desired
You may adjust different settings, depending on whether you have
selected a Sensor Cycle, Timed Cycle, or Steam Cycle (on some
models). See the “Cycle Guide” for detailed information.
NOTE: Not all options and settings are available with all cycles.
Not all cycles are on all models.
Sensor Cycles:
The temperature may be changed by touching Temp until the
desired dry temperature is lit. Once a cycle has started, the
temperature can be changed within the fi rst 5–8 minutes.
You can select a different dryness level, depending on your load.
Touch DRYNESS to scroll from Less to More to automatically adjust
the dryness level at which the dryer will shut off. Once a dryness
level is set, it cannot be changed without stopping the cycle.
Sensor Cycles give the best drying in the shortest time. Drying
time varies based on fabric type, load size, and dryness setting.
Drying time is estimated and may change throughout the cycle.
Drying time cannot be changed on Sensor Cycles.
Timed Cycles:
When you select a Timed Cycle, the time
appears in the display. Touch MORE TIME
or LESS TIME to increase or decrease the
time in 5-minute increments.
The temperature may be changed by touching
Temp until the desired dry temperature is lit.
Once a cycle has started, the temperature can be changed at
any time unless AirDry is selected; if Air Dry is selected, touch
POWER/CANCEL to cancel the cycle, reselect the desired cycle
settings, and touch START/PAUSE.
Steam Cycles (on some models):
Select Steam Refresh to reduce odors and light wrinkles in dry
loads. Do not add dryer sheets. Cycle time is estimated and may
change throughout the cycle. Cycle time cannot be changed on
Steam Cycles.
6. Select any additional options
Add additional options by touching that option. If you will be
unable to remove the load promptly, select the Wrinkle Prevent
option before touching Start/Pause.
NOTE: Not all options and settings are available with all cycles.
Appearance may vary.
Appearance may vary.
Appearance may vary.
:
AirDry
High
Less
More
Off
+Steam
Sensing
Cool Down
Check Vent
Wet
Damp
EXTRA POWER
:
AirDry
High
Less
More
Off
+Steam
Sensing
Cool Down
Check Vent
Wet
Damp
AirDry
High
Less
More
Off
+Steam
Sensing
Cool Down
Check Vent
Wet
Damp
:
AirDry
High
Less
More
Off
+Steam
Sensing
Cool Down
Check Vent
Wet
Damp
12
ADDITIONAL FEATURES
2. Align the two hooks on the front of the drying rack with the
holes in the dryer door opening and press down fully into
holes. Rest the rear support on the dryer back ledge.
USING THE DRYING RACK
To purchase a drying rack for your dryer, see “Accessories” for
more information. You will need your model and serial number
and the purchase date. Remove and discard any packing
material before use.
Use the drying rack for items that you do not want to tumble dry,
such as sweaters and tennis shoes. When you use the drying
rack, the drum continues to turn, but the rack remains stationary.
The drying rack is intended for use with the Timed Dry cycle
only. The drying rack cannot be used with Sensor Cycles.
To use the drying rack:
IMPORTANT: Do not remove the lint screen.
1. Open dryer door.
3. Place wet items on top of the drying rack. Allow space
around items for air to circulate. The drying rack does not
move, but the drum will rotate; be sure to leave adequate
clearance between items and the inside of the dryer drum.
Make sure items do not hang over the edges or between
drying rack grille.
4. Close the door.
5. Select a Timed Dry cycle. Items containing foam, rubber,
or plastic must be dried on a clothesline or by using the
Air Only setting or AirDry cycle, depending on model.
6. When the cycle is selected, the display shows the
default time. You can change the actual time in the cycle
by increasing or decreasing the cycle time.
7. Start the dryer.
NOTE: Check the lint screen and remove any lint accumulated
from items dried on the drying rack after the cycle is fi nished.
DRYER CARE
CLEANING THE DRYER LOCATION
Keep dryer area clear and free from items that would block the
airfl ow for proper dryer operation. This includes clearing piles
of laundry in front of the dryer.
CLEANING THE DRYER INTERIOR
To clean dryer drum:
1. Use a mild hand dish detergent mixed at a low
concentration with very warm water, and rub with
a soft cloth.
2. Rinse well with a wet sponge or towel.
3. Tumble a load of clean clothes or towels to dry drum
OR
Use a microfi ber cloth and hot water in a spray bottle
to clean the drum and a second microfi ber towel to dry.
NOTE: Garments that contain unstable dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the
rear of the dryer interior. These stains are not harmful to your
dryer and will not stain future loads of clothes. Dry unstable
dye items inside out to avoid transfer of dye.
REMOVING ACCUMULATED LINT
From inside the dryer cabinet
Lint should be removed every 2 years, or more often,
depending on dryer usage. Cleaning should be done
by a qualifi ed appliance servicer.
From the exhaust vent
Lint should be removed every 2 years, or more often,
depending on dryer usage.
13
CLEANING THE LINT SCREEN
Every-load cleaning
The lint screen is located in the door opening of the dryer.
Clean the lint screen before each load. A screen blocked
by lint can increase drying time.
To clean:
1. Pull the lint screen straight up. Roll lint off the screen with
your fi ngers. Do not rinse or wash screen to remove lint.
Wet lint is hard to remove.
2. Push the lint screen fi rmly back into place.
IMPORTANT:
n
Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
n
If lint falls off the screen into the dryer during removal,
check the exhaust hood and remove the lint. See “Venting
Requirements” in the Installation Instructions.
Laundry detergent and fabric softener residue can build up
on the lint screen. This buildup can cause longer drying times
for your clothes, or cause the dryer to stop before your load is
completely dry. The screen is probably clogged if lint falls off
while the screen is in the dryer.
Clean the lint screen with a nylon brush every 6 months,
or more frequently, if it becomes clogged due to a residue
buildup.
To wash:
1. Roll lint off the screen with your fi ngers.
2. Wet both sides of lint screen with hot water.
3. Wet a nylon brush with hot water and liquid detergent.
Scrub lint screen with the brush to remove residue buildup.
4. Rinse screen with hot water.
5. Thoroughly dry lint screen with a clean towel.
Reinstall screen in dryer.
AS NEEDED CLEANING
14
SPECIAL INSTRUCTIONS
FOR STEAM MODELS
Water Inlet Hose
Replace inlet hose and hose screen after 5 years of use to
reduce the risk of hose failure. Periodically inspect and replace
inlet hose if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hose, record the date of
replacement.
To Winterize the Dryer:
1. Unplug dryer or disconnect power.
2. Shut off water faucet.
3. Disconnect water inlet hose from faucet and drain.
To Use the Dryer Again:
1. Flush water pipes. Reconnect water inlet hose to faucet.
Turn on water faucet.
2. Plug in dryer or reconnect power as described in the
Installation Instructions.
NON-USE, STORAGE, AND MOVING CARE
Install and store your dryer where it will not freeze. Because
some water may stay in the hose, freezing can damage your
dryer. If storing or moving your dryer during freezing weather,
winterize it.
Non-Use or Storage Care
Operate your dryer only when you are at home. If you will be
on vacation or not using your dryer for an extended period of
time, you should:
1. Unplug dryer or disconnect power.
2. Clean lint screen. See “Cleaning the Lint Screen.”
3. Turn off the water supply to the dryer. This helps to avoid
unintended fl ooding (due to a water pressure surge) while
you are away.
Moving Care
For power supply cord-connected dryers:
1. Unplug the power supply cord.
2. Gas models only: Close shut-off valve in gas supply line.
3. Gas models only: Disconnect gas supply line pipe and
remove fi ttings attached to dryer pipe.
4. Gas models only: Cap the open gas supply line.
5. Steam models only: Shut off water faucet.
6. Disconnect the water inlet hose from faucet, then drain the
hose. Transport hose separately.
7. Make sure leveling legs are secure in dryer base.
8. Use tape to secure dryer door.
For direct-wired dryers:
1. Disconnect power.
2. Disconnect wiring.
3. Steam models only: Shut off water faucet.
4. Steam models only: Disconnect the water inlet hose from
faucet; then drain the hose. Transport hose separately.
5. Make sure leveling legs are secure in dryer base.
6. Use tape to secure dryer door.
Reinstalling the Dryer
Follow the Installation Instructions to locate, level, and connect
the dryer.
15
First try the solutions suggested here or visit our website at www.maytag.com/owners
(in Canada, www.maytag.ca/owners) for assistance and to possibly avoid a service call.
If you experience Possible Causes
Solution
Door not closed completely.
Make sure the dryer door is closed completely.
Touch and hold START/PAUSE until the display counts down
“3-2-1” and the dryer starts.
Household fuse is blown or circuit
breaker has tripped.
There may be two household fuses or circuit breakers for the dryer.
Check that both fuses are intact and tight, or that both circuit
breakers have not tripped. Replace the fuses or reset the circuit
breaker. If the problem continues, call an electrician.
TROUBLESHOOTING
Dryer will not run
Humming or whining noise
with Steam cycle selected
(on some models)
Water pump or water inlet valve
(depending on model) on dryer
is running.
Unusual Noise
Start/Pause not touched fi rmly
or held long enough.
Dryer Operation
Incorrect power supply. Electric dryers require 240 volt power supply. Check with a
qualifi ed electrician.
Wrong type of fuse.
Use a time-delay fuse.
The water pump or water inlet valve on the dryer is used during the
Steam function. If the dryer has just been installed or unused for an
extended period, the pump or valve may be louder and run longer.
This is normal.
NOTE: The valve may make this noise even with no water line connected.
Thumping noise
Dryer hasn’t been used in a while.
This is due to temporary fl at spots on the drum rollers.
The thumping sound will diminish after a few minutes.
Rattling or vibrating
noise
A small object caught between the
edges of dryer drum.
Check the front and rear edges of the drum for small objects.
Clean out pockets before laundering.
Dryer isn’t properly leveled.
The dryer may vibrate if not properly installed. See the Installation
Instructions. All four dryer feet should be in fi rm contact with
the fl oor.
Clothing is balled up in dryer. When balled up, the load will bounce, causing the dryer to vibrate.
Separate the load items and restart the dryer.
Dryer Results
Dryer will not heat Household fuse is blown or circuit
breaker has tripped.
The drum may be turning, but you may not have heat. Electric
dryers use two household fuses or circuit breakers. Replace the
fuses or reset the circuit breaker. If the problem continues, call
an electrician.
Clothes are not drying
satisfactorily or drying
times are too long
Lint screen is clogged with lint. Clean lint screen before each load.
Run the dryer for 5–10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not feel air
movement or air movement is minimal, clean exhaust system of lint
or replace exhaust vent with heavy metal or fl exible metal vent.
See the Installation Instructions.
The exhaust vent or outside exhaust
hood is clogged with lint, restricting
air movement.
Incorrect power supply.
Electric dryers require 240 volt power supply. Check with a
qualifi ed electrician.
Supply line valve not open.
For gas dryers, make sure that the valve on the gas supply line
is open.
Clicking noise
Gas valve operating.
On gas dryers, you may hear the gas valve clicking as it opens and
closes. This is normal.
Using Normal cycle.
For optimal drying times, use Regular cycle. For optimal energy
savings, use Normal cycle.
Loud humming or
increased noise during
cycle
Load is packed tightly or exhaust vent
is blocked.
Reduce load size to recommended load size in “Cycle Guide.”
Run the dryer for 5–10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not feel air
movement or air movement is minimal, clean exhaust system of lint
or replace exhaust vent with heavy metal or fl exible metal vent.
See the Installation Instructions.
First try the solutions suggested here or visit our website at
www.maytag.com/owners
(in Canada,
www.maytag.ca/owners
) for assistance and to possibly avoid a service call.
If you experience
Possible Causes
Solution
Door not closed completely.
Make sure the dryer door is closed completely.
Touch and hold START/PAUSE until the display counts down
“3-2-1” and the dryer starts.
Household fuse is blown or circuit
breaker has tripped.
There may be two household fuses or circuit breakers for the dryer.
Check that both fuses are intact and tight, or that both circuit
breakers have not tripped. Replace the fuses or reset the circuit
breaker. If the problem continues, call an electrician.
Dryer will not run
Humming or whining noise
with Steam cycle selected
(on some models)
Water pump or water inlet valve
(depending on model) on dryer
is running.
Unusual Noise
Start/Pause not touched fi rmly
or held long enough.
Dryer Operation
Incorrect power supply.
Electric dryers require 240 volt power supply. Check with a
qualifi ed electrician.
Wrong type of fuse.
Use a time-delay fuse.
The water pump or water inlet valve on the dryer is used during the
Steam function. If the dryer has just been installed or unused for an
extended period, the pump or valve may be louder and run longer.
This is normal.
NOTE:
The valve may make this noise even with no water line connected.
Thumping noise
Dryer hasn’t been used in a while.
This is due to temporary fl at spots on the drum rollers.
The thumping sound will diminish after a few minutes.
Rattling or vibrating
noise
A small object caught between the
edges of dryer drum.
Check the front and rear edges of the drum for small objects.
Clean out pockets before laundering.
Dryer isn’t properly leveled.
The dryer may vibrate if not properly installed. See the Installation
Instructions. All four dryer feet should be in fi rm contact with
the fl oor.
Clothing is balled up in dryer.
When balled up, the load will bounce, causing the dryer to vibrate.
Separate the load items and restart the dryer.
Dryer will not heat
Household fuse is blown or circuit
breaker has tripped.
The drum may be turning, but you may not have heat. Electric
dryers use two household fuses or circuit breakers. Replace the
fuses or reset the circuit breaker. If the problem continues, call
an electrician.
Incorrect power supply.
Electric dryers require 240 volt power supply. Check with a
qualifi ed electrician.
Supply line valve not open.
For gas dryers, make sure that the valve on the gas supply line
is open.
Clicking noise
Gas valve operating.
On gas dryers, you may hear the gas valve clicking as it opens and
closes. This is normal.
Dryer Results
Clothes are not drying
satisfactorily or drying
times are too long
Lint screen is clogged with lint.
Clean lint screen before each load.
Run the dryer for 5–10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not feel air
movement or air movement is minimal, clean exhaust system of lint
or replace exhaust vent with heavy metal or fl exible metal vent.
See the Installation Instructions.
The exhaust vent or outside exhaust
hood is clogged with lint, restricting
air movement.
Using Normal cycle.
For optimal drying times, use Regular cycle. For optimal energy
savings, use Normal cycle.
Loud humming or
increased noise during
cycle
Load is packed tightly or exhaust vent
is blocked.
Reduce load size to recommended load size in “Cycle Guide.”
Run the dryer for 5–10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not feel air
movement or air movement is minimal, clean exhaust system of lint
or replace exhaust vent with heavy metal or fl exible metal vent.
See the Installation Instructions.
16
Possible Causes
Solution
Dryer Results (cont.)
The dryer is located in a room with
temperature below 45ºF (7ºC).
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
The dryer is located in a closet. Closet doors must have ventilation openings at the top
and bottom of the door. The front of the dryer requires a minimum
of 1" (25 mm) of airspace and, for most installations, the rear of
the dryer requires 5" (127 mm). See the Installation Instructions.
Cycle time is too short
Steam models only: Clothes are
coming out of the Steam Refresh
cycle with damp or wet spots.
Under certain environmental or installation conditions, you may
experience underdrying. Select the Timed Dry cycle, medium
drying temperature, for 5 to 10 minutes.
The Sensor Cycle is ending early. Change the dryness level setting on Sensor Cycles. Increasing
or decreasing the dryness level will change the amount of drying
time in a cycle.
Lint on load Lint screen is clogged with lint.
Stains on load
Improper use of fabric softener.
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can
stain your garments. Do not use fabric softener sheets with
steam cycles.
Loads are wrinkled
The load was not removed from
dryer at the end of the cycle.
Steam models only: Select Steam Refresh cycle to tumble the
load with water and heat. This cycle is best for reducing wrinkles
from loads left in the dryer too long.
NOTE: Refer to garment care label instructions. Dry-clean-only
garments are not recommended.
The dryer was tightly packed. Dry smaller loads that can tumble freely.
Clothes are not drying
satisfactorily or drying
times are too long (cont.)
Steam models only: For steam
cycles, the water is not properly
connected with the dryer.
Make sure water is connected to the dryer. Check that water
inlet hose is connected to both the faucet and dryer’s water inlet
valve. Check that the water supply is turned on.
The load is too large and heavy
to dry quickly.
Fabric softener sheets are blocking
the grille.
The air outlet grille is just inside the door, behind the lint screen.
Check that it is not blocked by a fabric softener sheet.
Use only one fabric softener sheet, and use it only once.
Separate the load to tumble freely.
The load may not be contacting
the sensor strips on Sensor Cycles.
Level the dryer. See the Installation Instructions. All four dryer feet
should be in fi rm contact with the fl oor.
Clean lint screen before each load.
Stains on drum
Loose dyes in clothes.
Drum stains are caused by dyes in clothing (usually blue jeans).
These will not transfer to other clothing.
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.maytag.com/owners
(in Canada, www.maytag.ca/owners) for assistance and to possibly avoid a service call.
If you experience
The AirDry temperature setting
has been selected.
Select the correct temperature for the types of garments being
dried. See “Cycle Guide.”
The exhaust vent is not the correct
length.
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. See the Installation
Instructions.
The exhaust vent diameter is not the
correct size.
Use 4" (102 mm) diameter vent material.
The dryer is not level.
Clothes not contacting the moisture sensors during Sensor Cycles.
See “Level Dryer” in the Installation Instructions.
Possible Causes
Solution
Dryer Results (cont.)
The dryer is located in a room with
temperature below 45ºF (7ºC).
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
The dryer is located in a closet.
Closet doors must have ventilation openings at the top
and bottom of the door. The front of the dryer requires a minimum
of 1" (25 mm) of airspace and, for most installations, the rear of
the dryer requires 5" (127 mm). See the Installation Instructions.
Cycle time is too short
Steam models only:
Clothes are
coming out of the Steam Refresh
cycle with damp or wet spots.
Under certain environmental or installation conditions, you may
experience underdrying. Select the Timed Dry cycle, medium
drying temperature, for 5 to 10 minutes.
The Sensor Cycle is ending early.
Change the dryness level setting on Sensor Cycles. Increasing
or decreasing the dryness level will change the amount of drying
time in a cycle.
Lint on load
Lint screen is clogged with lint.
Stains on load
Improper use of fabric softener.
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can
stain your garments. Do not use fabric softener sheets with
steam cycles.
Loads are wrinkled
The load was not removed from
dryer at the end of the cycle.
Steam models only:
Select Steam Refresh cycle to tumble the
load with water and heat. This cycle is best for reducing wrinkles
from loads left in the dryer too long.
NOTE:
Refer to garment care label instructions. Dry-clean-only
garments are not recommended.
The dryer was tightly packed.
Dry smaller loads that can tumble freely.
Clothes are not drying
satisfactorily or drying
times are too long (cont.)
Steam models only:
For steam
cycles, the water is not properly
connected with the dryer.
Make sure water is connected to the dryer. Check that water
inlet hose is connected to both the faucet and dryer’s water inlet
valve. Check that the water supply is turned on.
The load is too large and heavy
to dry quickly.
Fabric softener sheets are blocking
the grille.
The air outlet grille is just inside the door, behind the lint screen.
Check that it is not blocked by a fabric softener sheet.
Use only one fabric softener sheet, and use it only once.
Separate the load to tumble freely.
The load may not be contacting
the sensor strips on Sensor Cycles.
Level the dryer. See the Installation Instructions. All four dryer feet
should be in fi rm contact with the fl oor.
Clean lint screen before each load.
Stains on drum
Loose dyes in clothes.
Drum stains are caused by dyes in clothing (usually blue jeans).
These will not transfer to other clothing.
First try the solutions suggested here or visit our website at
www.maytag.com/owners
(in Canada,
www.maytag.ca/owners
) for assistance and to possibly avoid a service call.
If you experience
The AirDry temperature setting
has been selected.
Select the correct temperature for the types of garments being
dried. See “Cycle Guide.”
The exhaust vent is not the correct
length.
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. See the Installation
Instructions.
The exhaust vent diameter is not the
correct size.
Use 4" (102 mm) diameter vent material.
The dryer is not level.
Clothes not contacting the moisture sensors during Sensor Cycles.
See “Level Dryer” in the Installation Instructions.
17
Possible Causes Solution
The drying cycle has been
interrupted by a power failure.
Touch and hold START/PAUSE to restart the dryer. NOTE: The
Control Lock function may be enabled when recovering from a
power failure. To unlock the control, touch and hold CONTROL
LOCK for at least 3 seconds.
There may be a problem with your
home power supply, keeping the
dryer’s heater from turning on.
The dryer will continue to run when this diagnostic code is present.
Touch any setting or option name to clear the code from the
display and return to the estimated time remaining.
Try the following:
Check to see if a household fuse has blown or circuit breaker
has tripped. Electric dryers use two household fuses or breakers.
Replace the fuse or reset the circuit breaker.
Confi rm that the power cord is properly installed. Refer to
the Installation Instructions for details.
Select a Timed Dry heated cycle, and restart the dryer.
If the message persists, consult a qualifi ed electrician.
“L” or “L2” Diagnostic Code
(low or no line voltage
condition)
The lint screen or vent is clogged;
the vent is crushed or kinked or
has too many turns.
The dryer will continue to run when this diagnostic code is present.
Touch any setting or option name to clear the code from the
display and return to the estimated time remaining.
Try the following:
• Clean lint screen.
• Check to see if the vent run from the dryer to the wall is
crushed or kinked.
• Confi rm that the vent run from the dryer to the wall is free
of lint and debris.
• Confi rm that the exterior vent exhaust hood is free of lint
and debris.
• Confi rm that your vent system falls within the recommended
run length and number of elbows for the type of vent you are
using. Refer to “Plan Vent System” in the Installaton Instructions
for details.
• Select a Timed Dry heated cycle, and restart the dryer.
• If the message persists, have your entire home venting
run cleaned.
Check Vent indicator is lit.
“PF” (power failure)
The dryer is in need of service. If a code beginning with an “F” appears in the display,
alternating between F# and E#, the dryer control has
detected a problem that requires service. Call for service.
Dryer Displaying Code Message or Cycle Status Indicator Lights Up
Dryer Results (cont.)
Load removed before cooldown
portion of cycle complete.
Allow the dryer to complete the cooldown portion of the cycle
before removing the load.
Load too hot
Using Timed Dry cycle with a high
temperature setting.
Select a Sensor cycle with a lower heat setting to avoid overdrying
the load.
Odors
Recent painting, staining, or
varnishing in the area where
your dryer is located.
Ventilate the area. When the odors or fumes are gone from the
area, rewash and dry the clothing.
Steam models only: For steam
cycles, the water is not properly
connected with the dryer.
Make sure water is connected to the dryer. Check that water inlet
hose is connected to both the faucet and dryer’s water inlet valve.
Check that the water supply is turned on.
Odors are left in garments after
wearing.
Steam models only: To remove odors left in garments after
wearing, select Steam Refresh. The Steam Refresh cycle is best
for reducing wrinkles from loads left in the dryer too long.
“F# E#” (F1 E1, F3 E1, etc.)
variable service codes
First try the solutions suggested here or visit our website at www.maytag.com/owners
(in Canada, www.maytag.ca/owners) for assistance and to possibly avoid a service call.
If you experience
TROUBLESHOOTING
The Control Lock is enabled. Touch and hold CONTROL LOCK for 3 seconds to unlock
the controls of the dryer. During this time, the LED Display
will count down “3-2-1.” When the Control Lock is disabled,
the LED Display will clear.
“Loc”
Possible Causes
Solution
Dryer Results (cont.)
Odors
Recent painting, staining, or
varnishing in the area where
your dryer is located.
Ventilate the area. When the odors or fumes are gone from the
area, rewash and dry the clothing.
Steam models only:
For steam
cycles, the water is not properly
connected with the dryer.
Make sure water is connected to the dryer. Check that water inlet
The drying cycle has been
interrupted by a power failure.
Touch and hold START/PAUSE to restart the dryer.
NOTE:
The
Control Lock function may be enabled when recovering from a
power failure. To unlock the control, touch and hold CONTROL
LOCK for at least 3 seconds.
There may be a problem with your
home power supply, keeping the
dryer’s heater from turning on.
The dryer will continue to run when this diagnostic code is present.
Touch any setting or option name to clear the code from the
display and return to the estimated time remaining.
Try the following:
Check to see if a household fuse has blown or circuit breaker
has tripped. Electric dryers use two household fuses or breakers.
Replace the fuse or reset the circuit breaker.
Confi rm that the power cord is properly installed. Refer to
the Installation Instructions for details.
Select a Timed Dry heated cycle, and restart the dryer.
If the message persists, consult a qualifi ed electrician.
“L” or “L2” Diagnostic Code
(low or no line voltage
condition)
The lint screen or vent is clogged;
the vent is crushed or kinked or
has too many turns.
The dryer will continue to run when this diagnostic code is present.
Touch any setting or option name to clear the code from the
display and return to the estimated time remaining.
Try the following:
• Clean lint screen.
• Check to see if the vent run from the dryer to the wall is
crushed or kinked.
• Confi rm that the vent run from the dryer to the wall is free
of lint and debris.
• Confi rm that the exterior vent exhaust hood is free of lint
and debris.
• Confi rm that your vent system falls within the recommended
run length and number of elbows for the type of vent you are
using. Refer to “Plan Vent System” in the Installaton Instructions
for details.
• Select a Timed Dry heated cycle, and restart the dryer.
• If the message persists, have your entire home venting
run cleaned.
Check Vent indicator is lit.
“PF” (power failure)
The dryer is in need of service.
If a code beginning with an “F” appears in the display,
alternating between F# and E#, the dryer control has
detected a problem that requires service. Call for service.
Dryer Displaying Code Message or Cycle Status Indicator Lights Up
Load removed before cooldown
portion of cycle complete.
Allow the dryer to complete the cooldown portion of the cycle
before removing the load.
Load too hot
Using Timed Dry cycle with a high
temperature setting.
Select a Sensor cycle with a lower heat setting to avoid overdrying
the load.
hose is connected to both the faucet and dryer’s water inlet valve.
Check that the water supply is turned on.
Odors are left in garments after
wearing.
Steam models only:
To remove odors left in garments after
wearing, select Steam Refresh. The Steam Refresh cycle is best
for reducing wrinkles from loads left in the dryer too long.
“F# E#” (F1 E1, F3 E1, etc.)
variable service codes
First try the solutions suggested here or visit our website at
www.maytag.com/owners
(in Canada,
www.maytag.ca/owners
) for assistance and to possibly avoid a service call.
If you experience
The Control Lock is enabled.
Touch and hold
CONTROL LOCK
for 3 seconds to unlock
the controls of the dryer. During this time, the LED Display
will count down “3-2-1.” When the Control Lock is disabled,
the LED Display will clear.
“Loc”
18
MAYTAG
®
LAUNDRY
LIMITED WARRANTY
1. Commercial, non-residential, multiple-family use, or use inconsistent
with published user
, operator, or inst
allation instructions.
2. In-home instruction on how to use your product.
3. Service to correct improper product maintenance or inst
allation,
installation not in accordance with electrical or plumbing codes, or
correction of household electrical or plumbing (e.g., house wiring, fuses,
or water inlet hoses).
4.
Consumable parts (e.g., light bulbs, batteries, air or water filters,
preservation solutions).
5. Defects or damage caused by the use of non-genuine Mayt
ag parts
or accessories.
6. Conversion of your product from natural gas or propane gas or revers
al
of appliance doors.
7.
Damage from accident, misuse, abuse, fire, floods, acts of God, or use
with products not approved by Mayt
ag.
8. Repairs to parts or systems to correct product damage or defects caused
by unauthorized service, alteration, or modification of the appliance.
9. Cosmetic damage including scratc
hes, dents, chips, and other damage
to appliance finishes unless such damage results from defects in
materials and workmanship and is reported to Mayt
ag within 3
0 days.
10
. Discoloration, rust, or o
xidation of surfaces resulting from caustic
or corrosive environments, including but not limited to, high salt
concentrations, high moisture or humidity
, or exposure to chemicals.
11. Pick-up or delivery. This product is intended for in-home repair.
12. Travel or transportation expenses for service in remote locations where
an authorized Mayt
ag servicer is not available.
13. Removal or reinstallation of inaccessible appliances or built-in fixtures (e.g.,
trim, decorative panels, flooring, cabinetry
, islands, countertops, drywall)
that interfere with servicing, removal, or replacement of the product.
14
.
Service or parts for appliances with original model/serial numbers
removed, altered, or not easily determined.
T
he cost of repair or replacement under these excluded
circumstances shall be borne by the customer.
ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS
REQUIRED TO OBTAIN WARRANTY SERVICE.
Please have the following information available when you call the
Customer eXperience Center:
n
Name, address, and telephone number
n
Model number and serial number
n
A clear, detailed description of the problem
n
Proof of purc
hase including dealer or retailer name and address
IF YOU NEED SERVICE:
1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions can be addressed
without service. Please t
ake a few minutes to review the Troubleshooting section of the Use and Care Guide or visit the “HOW-TO
S
& F
AQS” section of https://www.maytag.com/owners.html.
2. All warranty service is provided exclusively by our authorized Mayt
ag Service Providers.
In the U.S. and Canada, direct all requests for warranty service to:
Maytag Customer eXperience Center
In the U.S.A. call 1-800-344-1274. In Canada call 1-800-688-2002.
If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.
FIRST YEAR LIMITED WARRANTY
(PARTS AND LABOR)
For one year from the date of purchase, when this major
appliance is installed, operated, and maintained according to
instructions attached to or furnished with the product, Maytag
brand of Whirlpool Corporation or Whirlpool Canada LP
(hereafter “Maytag”) will pay for factory specified parts and
repair labor to correct defects in materials or workmanship
that existed when this major appliance was purchased, or
at its sole discretion replace the product. In the event of
product replacement, your appliance will be warranted by the
remaining term of the original unit’s warranty period.
SECOND THROUGH TENTH YEAR LIMITED
WARRANTY (DRUM MOTOR AND STAINLESS STEEL
OR POWDER COATED PAINT DRUM ONLY - LABOR
NOT INCLUDED)
In the second through tenth years from the date of original
purchase, when this major appliance is installed, operated, and
maintained according to instructions attached to or furnished
with the product, Maytag will pay for factory specified parts for
the following components to correct non-cosmetic defects in
materials or workmanship in these parts that prevent function
of this major appliance and that existed when this major
appliance was purchased. This is a limited 10 year warranty on
the below named parts only and does not include repair labor.
n
Drum (Side Walls Only) n
Drive Motor
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS
LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS
PROVIDED HEREIN. Service must be provided by a Maytag
designated service company. This limited warranty is valid
only in the United States or Canada and applies only when
the major appliance is used in the country in which it was
purchased. This limited warranty is effective from the date of
original consumer purchase. Proof of original purchase date is
required to obtain service under this limited warranty.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED TO TEN YEARS OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and
provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you.
This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the
exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives
you specific legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Maytag makes no representations about the quality, durability, or need for service or repair of this major appliance other than the
representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes
with this major appliance, you should ask Maytag or your retailer about buying an extended warranty.
01/18
TEN YEAR LIMITED WARRANTY
WHAT IS COVERED
WHAT IS NOT COVERED
19
SÉCURITÉ DE LA SÉCHEUSE
20
Dans l’État du Massachusetts, les instructions d’installation suivantes sont applicables :
■ Les travaux d’installation et réparation doivent être exécutés par un plombier ou tuyauteur qualifié ou licencié, ou par le
personnel qualifié d’une entreprise licenciée par l’État du Massachusetts.
■ Remplacer par des dispositifs de fermeture acceptables : Les robinets de gaz et robinets à bille installés pour l'utilisation
devraient être indiqués.
■ Si un conduit de raccordement flexible est utilisé, sa longueur ne doit pas dépasser 4 pi (121,9 cm).
– Ne pas entreposer ou utiliser de l’essence ou d’autres vapeurs ou liquides inammables
à proximité de cet appareil ou de tout autre appareil électroménager.
– QUE FAIRE DANS LE CAS D’UNE ODEUR DE GAZ :
•
Ne pas tenter d’allumer un appareil.
•
Ne pas toucher à un commutateur électrique; ne pas utiliser le téléphone se trouvant
sur les lieux.
•
Évacuer tous les gens de la pièce, de l’édice ou du quartier.
•
Appeler immédiatement le fournisseur de gaz d’un téléphone voisin. Suivre ses
instructions.
•
À défaut de joindre votre fournisseur de gaz, appeler les pompiers.
– L’installation et l’entretien doivent être effectués par un installateur qualié, une agence
de service ou le fournisseur de gaz.
AVERTISSEMENT :
RISQUE D
’
INCENDIE OU D
’
EXPLOSION
Le non-respect des avertissements de sécurité peut causer des dommages à la propriété,
des blessures graves, voire la mort.
IMPORTANT : L'installation du gaz doit se conformer aux codes locaux, ou en l'absence de codes locaux, au code d'installation
du gaz naturel ou du propane, CSA B149.1.
La sécheuse doit être électriquement reliée à la terre conformément aux codes locaux, ou en l'absence de codes locaux, au Code
canadien de l'électricité, partie 1, CSA C22.1.
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Maytag MED6630HW Le manuel du propriétaire
- Catégorie
- Sèche-linge
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Maytag MED6630HW Owner's manual