PURE EVOKE H3 OAK Manuel utilisateur

Evoke H3

1

Evoke H3

Thank you for choosing the Evoke H3. This user manual explains how

to use the various features of your Evoke H3. If you need more help,

you can view our help topics at support.pure.com.

FR

ES

IT

NO

DA

EN

DE

NL

2

3

Contents

Evoke H3 1

Safety 4

Getting started 5

Your Evoke 5

Setting up your Evoke H3 6

Switching your Evoke H3 on

and off 7

Changing the volume 7

Digital radio 8

Listening to digital radio 8

Changing the digital radio station 8

Automatically tuning to digital

radio stations 9

FM radio 9

Listening to FM radio 9

Changing the FM radio station 9

Changing the scan settings for

FM radio 9

Choosing stereo or mono

reception for FM radio 10

Radio station presets 10

About presets 10

Storing a radio station as a preset 10

Listening to a preset 11

Bluetooth and auxiliary

devices 11

Connecting a Bluetooth device 11

Connecting a device with an

auxiliary cable 12

Alarms 12

Setting an alarm 12

Cancelling an existing alarm 13

Snoozing or silencing an alarm 14

Timers 14

Setting the kitchen timer 14

Silencing the kitchen timer 15

Setting the sleep timer 15

Settings 16

Personalising the sound on your

Evoke H3 16

Display settings 16

Clock settings 17

Changing the language 18

Resetting to factory settings 19

Updating the software 19

Using a ChargePAK 20

About ChargePAKs 20

Inserting a ChargePAK 20

Troubleshooting 21

Speciﬁcations 22

EN

4

Safety

1. Read, heed and retain these instructions – All the safety and operating instructions should be read before this product is

used and retained for future reference. All warnings on the appliance and in the operating instructions should be followed

2. Failure to install or use the product in accordance with these instructions may impair the safety of the product and invalid

the warranty.

3. Use only power supply listed in these user manual/user instructions (supplied by Pure with model number SW0551000-AM)

to power the equipment and do not use the power supply for any other purpose.

4. The direct plug-in adapter is used as a disconnect device, the disconnect device shall remain readily operable and

accessible.

5. Do not immerse in water or use in a wet / moist environment, such as in the shower or bathroom if plugged into the mains

supply. The power supply shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,

placed above it.

6. Do not remove screws from or open the product casing.

7. Keep the product away from direct sunlight and from heat sources such as radiators, heaters or other appliances that

produce heat.

8. Danger of explosion if the battery is incorrectly replaced (ensure correct polarity). Replace only with the same or equivalent

type. The battery shall not be exposed to excessive heat such as sunshine, fire or similar. Attention is drawn to the

environmental aspects of battery disposal. See Section - “Using a ChargePAK”

9. Do not expose the product to naked flame sources, such lighted candles which should not be placed on or near the

product.

10. Ventilation should not be impaired by covering the product or power supply.

11. Clean only with a dry cloth.

12. This product is intended for use in moderate climates.

13. If the product is used in a manner not specified by the instructions, the product’s protection could be impaired.

14. Do not use the product if any damage is noticed.

15. Product repairs are only allowed to be carried out by competent and authorised personnel.

Safety instructions and cautions

Symbol Description

This symbol is used on the product to indicate a caution and that instructions should be read before use.

This symbol indicates DC voltage.

This symbol indicates where the product is switched on or put into standby.

Symbols used on this product

5

Getting started

Your Evoke

Front controls

1

1 Presets Press to store and access your favourite radio stations

2 Alarm Press to set an alarm, a kitchen timer or a sleep timer

3 Source Press to change between digital radio, FM radio, Bluetooth, and auxiliary input

4 Volume/Scroll Turn to change the volume, press to mute the volume

Tip: When you are in a menu, you can turn and press the Volume dial to

choose settings and options. To then use the dial to change the volume again,

wait 10 seconds or press

.

5 Select Press to browse radio stations, or choose settings and options

6 Menu Press to change settings and options

7 Back Press when in the menu to go back to the previous screen

1 Standby Switch your Evoke H3 on and off, or put it in standby

Top controls

Source

Menu

Select

1

2

3

4+

1

2

3

4

6

7

5

EN

6

Rear connections

x inAu

Input for supplied

mains adapter only

3.5mm output for

stereo headphones

Analogue stereo

input for auxiliary

cables

Micro USB

connector for

software updates

Setting up your Evoke H3

To set up your Evoke H3:

1. Unclip the aerial and fully extend it.

2. Connect the supplied mains adapter to the input on the back of your Evoke H3.

3. Plug the mains adapter into the mains supply.

>

+

–

5.5V DC 1A

Aux in

+

–

5.5V DC 1A Aux in

5.5V DC 1A

+

–

5.5V DC 1A

Aux in

7

Switching your Evoke H3 on and off

If you have a ChargePAK rechargeable battery, insert it before you switch your Evoke H3 on. Read more

about using a ChargePAK on page 20.

To switch your Evoke H3 on:

• Press

.

Note: When you switch your Evoke H3 on for the first time, it starts tuning to digital radio stations.

After the autotune is complete, you can start listening to digital radio.

To switch your Evoke H3 off or put it in standby:

• Press

.

If your Evoke H3 is being powered by a ChargePAK, your Evoke H3 switches off. If your Evoke

H3 is connected to a power socket, your Evoke H3 enters standby. In standby, your Evoke H3 uses a

low amount of power and displays the time and date on the screen.

Changing the volume

To change the volume:

• To increase the volume, turn the Volume dial clockwise.

• To decrease the volume, turn the Volume dial anticlockwise.

To mute the volume:

• Press the Volume dial.

EN

8

Digital radio

Listening to digital radio

To listen to digital radio:

• Press

Source

until ‘Digital Radio’ is displayed.

Tip: Some digital radio stations also broadcast information and graphics, such as music album

artwork or weather updates. Press and hold the Select button to change between slideshow, large

slideshow and display modes.

Changing the digital radio station

To change the digital radio station:

1. Press

or to browse through the available radio stations.

2. Press

Select

to change radio station.

> >

Tip: A ‘>>’ next to a radio station name means the station has a secondary service, which provides more

content. The secondary service is listed below the radio station with a ‘<<’ next to the service name.

Secondary services may only be available at certain times.

A ‘?’ next to a radio station name means the station is inactive or unavailable.

Station List

BBC Radio 1

BBC Radio 1Xtra

BBC Radio 2

BBC Radio 3

BBC Radio 4

BBC Radio 4Extra

BBC Radio 5 Live

Select

9

Automatically tuning to digital radio stations

When you switch your Evoke H3 on for the ﬁrst time, it automatically scans for digital radio stations. If you

move your Evoke H3 to a new location, perform an autotune to update the list of radio stations.

To automatically tune to digital radio stations:

1. Press

Menu

.

2. Press the Select buttons to choose ‘Autotune’.

Your Evoke H3 starts scanning for digital radio stations.

FM radio

Listening to FM radio

To listen to FM radio:

• Press

Source

until ‘FM’ is displayed.

Changing the FM radio station

To change the FM radio station:

• To scan to the previous or next radio station, press and hold

or .

• To manually tune to a radio station, press

or .

The frequency steps up or down by 0.05 MHz.

Changing the scan settings for FM radio

When you scan for FM radio stations, you can include all radio stations or only those with a strong signal.

To change scan settings for FM radio:

1. Press

Menu

.

2. Press the Select buttons to choose ‘Scan Setting’.

3. Press the Select buttons to choose ‘Strong Stations Only’ or ‘All Stations’.

EN

10

Choosing stereo or mono reception for FM radio

By default, your Evoke H3 uses stereo reception for FM radio. If your FM radio stations have a weak signal,

try using mono reception to improve the signal strength.

To choose stereo or mono reception:

1. Press

Menu

.

2. Press the Select buttons to choose ‘Stereo’.

3. Press the Select buttons to choose ‘FM Stereo’ or ‘Forced Mono’.

Radio station presets

About presets

You can store your favourite radio stations as presets. You can use presets to quickly tune to your stored

radio stations whenever you want.

On the top of your Evoke H3, there are four preset buttons. Use

1

to

3

for quick access to your

favourite radio stations. Use

4+

to open a list of all your presets.

You can store up to 20 digital radio stations and up to 20 FM radio stations as presets.

Storing a radio station as a preset

To store a radio station to a preset from 1 to 3:

1. Tune to the radio station you want to store.

2. Choose a preset button from

1

to

3

then press and hold it until a is displayed.

Tip: If there is already a radio station stored to the preset you’ve selected, the new station replaces it.

To store a radio station to the preset list:

1. Tune to the radio station you want to store.

2. Press and hold

4+

until the preset list is displayed.

3. Press the Select buttons to choose a preset number. A

is displayed.

Tip: If there is already a radio station stored to the preset you’ve selected, the new station replaces it.

11

>

Listening to a preset

To listen to a preset from 1 to 3:

• Press a preset button from

1

to

3

. For example, to listen to the radio station stored as preset

2, press

2

.

To listen to any preset:

1. Press

4+

to open the preset list.

2. Press the Select buttons to choose a preset.

Bluetooth and auxiliary devices

Connecting a Bluetooth device

You can use Bluetooth to wirelessly connect to a device, such as a mobile phone or tablet. You can then

stream music from your mobile phone or tablet through your Evoke H3.

The ﬁrst time you connect a Bluetooth device to your Evoke H3, you need to pair them. After you’ve paired

a device with your Evoke H3, your Evoke H3 remembers it for the next time.

To connect a Bluetooth device:

1. Press

Source

until ‘Bluetooth’ is displayed.

2. On your Bluetooth device, switch Bluetooth on and connect to your Evoke H3.

Note: For more information, see your Bluetooth device’s user manual. If you are asked to enter a

passcode, enter 0000.

When ‘Connected’ is displayed on your Evoke H3 screen, your Evoke H3 is ready to stream music.

Save to Preset

1: BBC Radio 1

2: (Empty)

3: (Empty)

4: (Empty)

5: (Empty)

6: (Empty)

7: (Empty)

4+

EN

12

Tip: If you want to connect a different Bluetooth device to your Evoke H3, switch off Bluetooth on the

connected device first.

Connecting a device with an auxiliary cable

You can use an auxiliary cable to connect a device, such as an MP3 player, to your Evoke H3. You can

then enjoy music saved on the device through your Evoke H3.

To connect a device with an auxiliary cable:

1. Press

Source

until ‘Auxiliary Input’ is displayed.

2. Insert an auxiliary cable into the Aux in socket on the back of your Evoke H3.

3. Insert the other end of the auxiliary cable into the device you want to connect.

Your Evoke H3 is now ready to play music from the connected device.

Alarms

To wake up to your favourite radio station, you can set up to two alarms on your Evoke H3.

Note: You cannot set alarms when your Evoke H3 is being powered by a ChargePAK.

Setting an alarm

To set an alarm:

1. Press

.

2. Press the Select buttons to choose ‘Alarm 1’ or ‘Alarm 2’.

3. Press the Select buttons to change settings for the alarm.

Bluetooth

14-7-2016

Thursday

Connected

13

‘Alarm’ Turn the alarm on or off

‘Frequency’ Choose how often you want the alarm to sound

‘Wake Up time’ Choose the time for the alarm

‘Source’ Choose to wake up to an FM or digital radio station, or a buzzer

Tip: To choose FM or digital radio, you need to have stored a

radio station as a preset.

‘Preset’ Choose a radio station to wake up to

Tip: If you do not choose a preset, the default setting is the radio

station that you last listened to.

‘Duration’ Choose how many minutes the alarm sounds for

‘Volume’ Choose the volume for the alarm

4. When you have made all of your changes, press

Menu

to exit the menu.

The

1

or

2

symbol is displayed at the bottom of the screen when an alarm is set.

>

Alarm

Alarm 1

Alarm 2

Timer

Sleep

On 09:00

Off 11:30

>

Alarm 1 Info.

Alarm

Frequency

Wake Up time

Source

Preset

Duration

Volume

On

Daily

9:00 AM

FM

Last Listened

60

5

Cancelling an existing alarm

To cancel an existing alarm:

1. Press .

2. Press the Select buttons to choose ‘Alarm 1’ or ‘Alarm 2’.

3. Press the Select buttons to change the ‘Alarm’ setting to ‘Off’.

EN

14

Snoozing or silencing an alarm

To snooze an alarm:

• Press the Select button or the Volume dial.

The alarm snoozes for 5 minutes.

Tip: For a longer snooze, press the Select button multiple times.

To silence an alarm:

• Press

.

Timers

Setting the kitchen timer

The kitchen timer counts down and then ends with an alarm tone.

To set the kitchen timer:

1. Press

.

2. Press the Select buttons to choose ‘Timer’.

3. Press

or to choose the duration of the timer.

4. Press

Select

to start the timer.

The symbol is displayed at the bottom of the screen when the timer is set.

>

Alarm

Alarm 1

Alarm 2

Timer

Sleep

On 09:00

Off 11:30

>

Kitchen timer

00:00

15

Silencing the kitchen timer

To silence the kitchen timer:

• Press .

Setting the sleep timer

The sleep timer puts your Evoke H3 in standby after a set amount of time.

To set the sleep timer:

1. Press

.

2. Press the Select buttons to choose ‘Sleep’.

3. Press

or to choose the duration of the timer.

Tip: You can choose between 15 and 90 minutes.

4. Press

Select

to start the timer.

The symbol and remaining time is displayed at the bottom of the screen when the timer is set.

>

Alarm

Alarm 1

Alarm 2

Timer

Sleep

On 09:00

Off 11:30

>

Set Sleep Timer

15 minutes

EN

16

Settings

Personalising the sound on your Evoke H3

Use the equaliser setting to get the most out of your music. There are several equaliser settings set up

already. For example, to hear classical music at its best, change the equaliser setting to ‘Classic’. You can

also customise the equaliser to change the treble, bass and loudness.

To use the equaliser:

1. Press

Menu

.

2. Press the Select buttons to choose ‘Audio’.

3. Choose an equaliser setting:

• To choose an equaliser setting, press the Select buttons.

• To use custom settings, press the Select buttons to choose ‘Custom’. Then press the Select

buttons to change the treble, bass and loudness.

Display settings

Changing the information displayed on the screen

You can change the information that is displayed on the screen when you are listening to the radio. For

example, you can display scrolling information about the current radio station.

To change the information displayed on the screen:

1. Press

Menu

.

2. Press the Select buttons to choose ‘Display’.

3. Press the Select buttons to choose ‘Info’.

4. Press the Select buttons to choose the information to display.

Changing the screen brightness

Your Evoke H3 has a light sensor, which adjusts the screen brightness based on your surroundings. You

can also manually change the screen brightness.

To help save energy, you can dim the screen after 10 seconds of inactivity.

17

To change the brightness of the screen when switched on:

1. Press

Menu

.

2. Press the Select buttons to choose ‘Display’.

3. Press the Select buttons to choose 'Backlight'.

4. Press the Select buttons to choose ‘On Level’.

5. Press the Select buttons to choose a brightness level. To make your screen brighter, choose a

higher number. To automatically set the screen brightness, choose ‘Auto’.

To dim the screen after 10 seconds of inactivity:

1. Press

Menu

.

2. Press the Select buttons to choose ‘Display’.

3. Press the Select buttons to choose 'Backlight'.

4. Press the Select buttons to choose ‘Duration’.

5. Press the Select buttons to choose ‘Timed’.

To change the brightness of the screen when dimmed:

1. Press

Menu

.

2. Press the Select buttons to choose ‘Display’.

3. Press the Select buttons to choose 'Backlight'.

4. Press the Select buttons to choose ‘Dim Level’.

5. Press the Select buttons to choose a brightness level. To make your screen brighter, choose a

higher number.

Clock settings

Setting the time and date

Your Evoke H3 can use FM and digital radio signals to set the time and date automatically. If the time and

date do not update automatically, you can set them manually.

To set the time and date automatically:

1. Press

Menu

.

EN

18

2. Press the Select buttons to choose ‘Clock’.

3. Press the Select buttons to choose ‘Auto Update’.

4. Press the Select buttons to choose how to set the time and date.

To set the time and date manually:

1. Press

Menu

.

2. Press the Select buttons to choose ‘Clock’.

3. Press the Select buttons to choose ‘Set Time/Date’.

4. Press the Select buttons to set the date.

5. Press the Select buttons to set the time.

Changing the time format

To change the time format:

1. Press

Menu

.

2. Press the Select buttons to choose ‘Clock’.

3. Press the Select buttons to choose ‘Set 12/24 Hour’.

4. Press the Select buttons to choose the time format.

Changing the date format

To change the date format:

1. Press

Menu

.

2. Press the Select buttons to choose ‘Clock’.

3. Press the Select buttons to choose ‘Set Date Format’.

4. Press the Select buttons to choose the date format.

Changing the language

You can change the language of menus and settings.

To change the language:

1. Press

Menu

.

La page charge ...

PURE EVOKE H3 OAK Manuel utilisateur

Ce manuel convient également à

PURE EVOKE H3 OAK Manuel utilisateur

dans d''autres langues

Documents connexes