TP-LINK Deco M4 Mode d'emploi

Marque: TP-LINK

Modèle: Deco M4

Taper: Mode d'emploi

Ce manuel convient également à

Deco M3

Whole Home Mesh Wi-Fi System

Seamless Roaming | Parental Controls | Easy Setup

User Guide

AC1200 Whole Home Mesh Wi-Fi System

1910012652 REV2.0.0

Contents

About This Guide ···················································· 1

Appearance ······························································· 2

Set Up Your Deco ··················································· 3

Dashboard ·································································· 5

Wi-Fi Settings···························································· 6

Parental Controls ···················································· 7

Advanced Features ··············································· 8

Update Decos ························································12

Managers ··································································13

Authentication ························································14

About This Guide

This guide provides a brief introduction to Deco Whole Home Mesh Wi-Fi System and the Deco app, as well as regulatory information.

Note: Features available in Deco may vary by model and software version. Deco availability may also vary by region or ISP. All images, steps, and

descriptions in this guide are only examples and may not reect your actual Deco experience.

Conventions

In this guide, the following conventions are used:

Convention Description

Deco

Stands for Deco Whole Home Mesh Wi-Fi System/Unit.

Underline

Hyperlinks are in teal and underlined. You can click to

redirect to a website or a specic section.

Teal

Key information appears in teal, including management

page text such as menus, items, buttons and so on.

Note:

Ignoring this type of note might result in a malfunction

or damage to the device.

Tips:

Indicates important information that helps you make

better use of your device.

More Info

• Specific product information can be found on the product page at

https://www.tp-link.com.

• A Technical Community is provided for you to discuss our products at

https://community.tp-link.com.

• Our Technical Support contact information can be found at the Help

center of the Deco app and the Contact Technical Support page at

https://www.tp-link.com/support.

Speed/Coverage/Device Quantity Disclaimer

Maximum wireless transmission rates are the physical rates derived from

IEEE Standard 802.11 specifications. Range, coverage, and maximum

quantity of connected devices are based on test results under normal

usage conditions. Actual wireless data throughput. wireless coverage,

and quantity of connected devices are not guaranteed and will vary

as a result of 1) environmental factors, including building materials,

physical objects, and obstacles, 2) network conditions, including local

interference, volume and density of traffic, product location, network

complexity, and network overhead, and 3) client limitations, including

rated performance, location, connection quality, and client condition.

MU-MIMO Disclaimer

Use of MU-MIMO requires clients to also support MU-MIMO.

Appearance

Each Deco has an LED that changes color according to its status, two RJ-45 Ethernet ports, a power slot, and a Reset button. See the explanation

below:

Yellow pulse:

Deco is resetting.

Yellow solid:

Deco is starting up.

Blue pulse:

Deco is ready for setup.

Blue solid:

Deco is setting up.

White pulse:

Deco is upgrading rmware.

White solid:

Deco is registered and all is well.

Red pulse:

Deco is disconnected from main Deco.

Red solid:

Deco has an issue.

Ethernet Ports:

For connecting Deco to your modem, the

Ethernet outlet or other internet devices.

Reset Button:

Press to reset Deco to factory default settings.

Power Slot:

For connecting Deco to the power socket via

the provided power adapter.

Set Up Your Deco

Follow the steps below to set up your Deco Whole Home Mesh Wi-Fi System.

1. Download and install the Deco app

Scan the QR code below or go to Google Play

or the Apple App Store to download the Deco

app.

Install the app on your Android or iOS

smartphone or tablet.

2. Log in or sign up with TP-Link ID

Open the app. Use your TP-Link ID to log in.

If you don’t have a TP-Link ID, tap Sign Up. The

Deco app will guide you through the rest.

3. Connect Deco to your modem

Find and power o your modem. Connect your

Deco to the modem and power them both on.

If you don't have a modem, connect the

Ethernet outlet directly to your Deco.

4. Select a location

Select a location for this Deco. If its location

is not listed, you can create a new one by

choosing Custom.

5. Create your Wi-Fi network

Set a network name and a password. These

will be the name and password you use to

connect your devices to Wi-Fi.

6. Add more Decos

You can add more Decos to expand Wi-Fi

coverage. The app will guide you through the

process of adding more Decos one by one.

Dashboard

After you successfully set up your Deco network, you will see the dashboard of the Deco app. Here you can view the connected devices and their

internet speeds, tap the

(Internet) icon to check the working status of all Decos, and tap the icon to display more features.

View connected devices

Check the working status of all Decos Display more features

Wi-Fi Settings

You can change the network name and password of your main network, create a separate network for guests, and shake your device to share the

network details easily with family and friends.

Change main network settings

Create a guest network Shake to share Wi-Fi

Parental Controls

Create proles for family members and specify the devices that belong to them. Set individualized parental controls including when and for how long

each person can access the internet. Block inappropriate content and pause the internet if necessary.

Parental Controls

Select lter level Set time controls

Advanced Features

Additional features are available under the Advanced menu. You can congure and change settings according to your needs.

Advanced features

Change IPv4 settings Change IPv6 settings

Set up port forwarding rulesReserve IP addresses for specic devices

Control the LED on Deco

Enable fast roaming for wireless devicesChange VLAN settings

Turn on/o notications

Change the operating mode

Update Decos

TP-Link is dedicated to improving product features and providing a better customer experience. Update Deco when prompted in the Deco app.

Update Available

Updating Deco Up-to-date

Managers

Add friends and family members to help manage your Deco network. Each manager should have their own TP-Link ID.

Managers

Add a manager Manager list

Authentication

Specifications are subject to change without notice. is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product

names are trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or

FCC Compliance Information Statement

Product Name: AC1200 Whole Home Mesh Wi-Fi System

Model Number: Deco M4/M4R/M3

Component Name Model

I.T.E POWER SUPPLY T120150-2B1

Responsible party:

TP-Link USA Corporation, d/b/a TP-Link North America, Inc.

Address: 145 South State College Blvd. Suite 400, Brea, CA 92821

Website: http://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6803

E-mail: [email protected]om

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications

could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be

co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this

transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction

with any other antenna or transmitter.”

FCC Compliance Information Statement

Product Name: I.T.E POWER SUPPLY

Model Number:

T120150-2B1

Responsible party:

TP-Link USA Corporation, d/b/a TP-Link North America, Inc.

Address: 145 South State College Blvd. Suite 400, Brea, CA 92821

Website: http://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6803

E-mail: [email protected]om

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards,

FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2019-09-09

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take

adequate measures.

OPERATING FREQUENCY(the maximum transmitted power)

2412MHz—2483.5MHz (20dBm)

5150MHz—5250MHz (23dBm)

EU declaration of conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU,

2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce

RF Exposure Information

This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way

of health protection.

The device complies with RF specifications when the device used at 20 cm from your body.

Attention: This device may only be used indoors in all EU member states and EFTA countries.

Canadian Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-

exempt RSS(s). Operation is subject to the following two conditions:

La page charge ...

TP-LINK Deco M4 Mode d'emploi

Marque: TP-LINK

Modèle: Deco M4

Taper: Mode d'emploi

Ce manuel convient également à

Deco M3

Télécharger le PDF

rapport

dans d''autres langues

English: TP-LINK Deco M4 User guide

TP-LINK Deco M4 Mode d'emploi

Ce manuel convient également à

TP-LINK Deco M4 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents