Ryobi RY142300 Le manuel du propriétaire

Marque: Ryobi

Modèle: RY142300

Catégorie: Nettoyeurs haute pression

Taper: Le manuel du propriétaire

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

ELECTRIC PRESSURE WASHER

LAVEUSE À PRESSION À ÉLECTRIQUE

LAVADORA DE PRESIÓN A ELÉCTRICA

RY142300

WARNING: To reduce the risk of

injury, the user must read and understand

the operator’s manual before using this

product.

TABLE OF CONTENTS

 Important Safety Instructions ............... 2

 Specific Safety Rules ........................3-4

 Symbols .............................................5-6

 Electrical ............................................... 7

 Features ................................................8

 Assembly .........................................8-10

 Operation .......................................10-14

 Maintenance ..................................14-15

 Troubleshooting .................................16

 Parts Ordering and Service .. Back Page

AVERTISSEMENT : Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation avant

d’employer ce produit.

TABLE DES MATIÈRES

 Instructions importantes

concernant la sécurité.......................... 2

 Règles de sécurité particulières ........3-4

 Symboles ...........................................5-6

 Caractéristiques électriques ..............6-7

 Caractéristiques ................................... 8

 Assemblage .....................................8-10

 Utilisation .......................................10-14

 Entretien ........................................14-15

 Dépannage ......................................... 16

 Commande de pièces et

réparation ............................ Páge arrière

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe leer

y comprender el manual del operador

antes de usar este producto.

ÍNDICE DE CONTENIDO

 Instrucciones de seguridad

importantes .......................................... 2

 Reglas de seguridad específicas ......3-4

 Símbolos ...........................................5-6

 Aspectos eléctricos ........................... 6-7

 Características ..................................... 8

 Armado ............................................ 8-10

 Funcionamiento .............................10-14

 Mantenimiento ...............................14-15

 Solución de problemas ...................... 16

 Pedidos de piezas y

servicio .............................Pág. posterior

SAVE THIS MANUAL FOR

FUTURE REFERENCE

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner toutes les

figures mentionnées dans le manuel d’utilisation.

Consulte esta sección desplegable para ver todas

las figuras a las que se hace referencia

en el manual del operador.

iii

Fig. 1

Fig. 2

A - Test button (bouton de test, botón de prueba)

B - Reset button (bouton de réinitialisation,

botón de reajuste)

Fig. 3

A - On/off switch (commutateur marche / arrêt, interruptor de encendido)

B - Nozzle storage (rangement de buses, almacenamiento para boquilla)

C - Spray wand (lance de pulvérisation, tubo rociado)

D - Motor (moteur, motor)

E - Soap tank (réservoir de savon, tanque de jabón)

F - Trigger with lock-out (gâchette avec verouillage, gatillo con seguro)

G - Power cord storage bracket (support de rangement pour cordon

d’alimentation, soporte para almacenamiento del cordón eléctrico)

H - Trigger handle (poignée de gâchete, mango del gatillo)

I - High pressure hose (tuyau haute pression, manguera de alta presión)

A - Pressure washer power cord

(cordon d’alimentation de la

laveuse à pression, cordón

de corriente de la lavadora de

presión)

B - Drip loop (boucle

d’égouttement, vuelta de goteo)

C - Extension cord (cordon

prolongateurs, cordón de

extensión)

Fig. 5

Fig. 6

Fig. 7

A - Axle (essieu, eje)

B - Wheel (roue, rueda)

C - Washer (rondelle, arandela)

D - Hitch pin (goupille de sûreté, pasador del

enganche)

Fig. 4

A - Button (bouton, botón)

B - Push to insert (pousser pour insérer,

presione para insertar)

Fig. 8

Fig. 9

Fig. 10

A - Trigger handle (poignée à gâchette, mango

del gatillo)

B - Spray wand (poignée à gâchette, tubo

rociador)

Fig. 11

A - Collar (collier, casquillo)

B - Inlet coupler (raccord d’entrée, acoplador de

entrada)

C - High pressure hose (tuyau haute pression,

manguera de alta presión)

A - Threaded outlet (têton fileté, conexión

roscada)

B - Collar (collier, casquillo)

C - High-pressure hose (flexible haute pression,

manguera de alta presión)

A - Water intake (rise d’eau, entrada de agua)

B - Garden hose (tuyau d’arrosage, manguera de

jardín)

A - On/off switch (commutateur marche / arrêt,

interruptor de encendido/apagado)

A - Trigger (gâchette, gatillo)

B - Lock-out (verrouillage, seguro)

A - Spray wand (lance de pulvérisation, tubo

rociador)

B - Nozzle (buse, boquilla)

C - Turbo nozzle (buse de turbo, boquilla de

turbo)

D - Pull back the quick-connect collar (tirer la

bague à connexion rapide, tire del collar de

conexión rápida)

E - Push the nozzle into place (insérer en place

la buse, introduzca la boquilla en su lugar)

F - Push the collar forward (poussez en avant la

bague, empuje del collar adelante)

Fig. 12

TO MOVE THE MACHINE

DÉPLACEMENT DE LA MACHINE

PARA MOVER LA MÁQUINA

Fig. 14

Fig. 13

Fig. 15

Fig. 16

A - Power cord (cordon d’alimentation, cordón

de corriente)

B - Power cord storage bracket (support de

rangement pour cordon d’alimentation,

soporte para almacenamiento del cordón

eléctrico)

Fig. 18

Fig. 17

A - Straightened paper clip (trombone droit, clip

para papel abierto)

B - Nozzle (embout, boquilla)

Fig. 19

A - Cap (capuchon, tapa)

B - Detergent (détergente, detergente)

C - Soap tank (réservoir de savon, tanque de

jabón)

Fig. 20

A - Threaded top (bouchon vissé, parte superior

roscada)

B - Rubber seal (joint de caoutchouc, sello de

goma)

C - Paper seal (sceaux de papier, sello de papel)

D - Water intake (rise d’eau, entrada de agua)

E - Pump outlet (sortie de la pompe, orificio de

descarga de la bomba)

F - Pump protector (protecteur de pompe,

protector de bomba)

TO STORE THE MACHINE

REMISAGE DE LA MACHINE

PARA GUARDAR LA MÁQUINA

2 — English

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below may result in electric shock,

fire, and/or serious personal injury.

WARNING:

When using this product basic precautions should always

be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING

THIS PRODUCT

 To reduce the risk of injury, close supervision is neces-

sary when a product is used near children.

 Be thoroughly familiar with controls. Know how to stop

the product and release pressure quickly.

 Stay alert and exercise control. Watch what you are

doing and use common sense. Do not operate product

when you are tired. Do not rush.

 Do not operate the product while under the influence

of drugs, alcohol, or any medication.

Keep the area of operation clear of all persons,

particularly small children, and pets.

 Don’t overreach or stand on a ladder, rooftop, or other

unstable support. Keep proper footing and balance at

all times.

 Follow the maintenance instructions specified in this

manual.

 This product is provided with a ground fault circuit

interrupter built into the power cord plug. If replace-

ment of the plug or cord is needed, use only identical

replacement parts.

 WARNING: Risk of injection or injury – Do not direct

discharge stream at persons.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

This product must be grounded. If it should malfunction or

breakdown, grounding provides a path of least resistance for

electric current to reduce the risk of electric shock. This prod-

uct is equipped with a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

DANGER: Improper connection of the equipment-grounding

conductor can result in a risk of electrocution. Check with a

qualified electrician or service personnel if you are in doubt

as to whether the outlet is properly grounded. Do not modify

the plug provided with the product – if it will not fit the outlet,

have a proper outlet installed by a qualified electrician. Do

not use any type of adaptor with this product.

GROUND FAULT CIRCUIT INTERRUPTER

PROTECTION

This pressure washer is provided with a ground-fault circuit-

interrupter (GFCI) built into the plug of the power supply

cord. This device provides additional protection from the risk

of electric shock. Should replacement of the plug or cord

become necessary, use only identical replacement parts that

include GFCI protection.

EXTENSION CORDS

See Figure 1.

Use only 3-wire extension cords that have 3-prong grounding-

type plugs and 3-pole cord connectors that accept the plug

from the product. Use only extension cords that are intended

for outdoor use. These extension cords are identified by a

marking "Acceptable for use with outdoor appliances; store

indoors while not in use." Use only extension cords having

an electrical rating not less than the rating of the product. Do

not use damaged extension cords. Examine extension cord

before using and replace if damaged. Do not abuse exten-

sion cord and do not yank on any cord to disconnect. Keep

cord away from heat and sharp edges. Always disconnect

the extension cord from the receptacle before disconnecting

the product from the extension cord.

WARNING: To reduce the risk of electrocution, keep all

connections dry and off the ground. Do not touch plug with

wet hands.

To avoid the possibility of the product plug or outlet getting

wet, the operator should arrange a “drip loop” in the cord

connecting the product to the outlet. The “drip loop” is that

part of the cord below the level of the outlet, or the connector

if an extension cord is used, to prevent water traveling along

the cord and coming in contact with the outlet.

IMPORTANT SAFETY INSTRUCTIONS

3 — English

 Use caution when positioning the pressure washer

for use. Warm air from the motor could cause discolored

spots on grass.

 Know your product. Read the operator’s manual care-

fully. Learn the machine’s applications and limitations

as well as the specific potential hazards related to this

product.

 To reduce the risk of injury, keep children and visitors

away. All visitors should wear safety glasses and be kept

a safe distance from work area.

 Use right product. Don’t force product or attachment to

do a job it was not designed for. Don’t use it for a purpose

not intended.

 Dress properly. Wear long pants and long sleeves. Do

not wear loose clothing, neckties, or jewelry. They can get

caught and draw you into moving parts. Rubber gloves

and nonskid footwear are recommended when working

outdoors. Also wear protective hair covering to contain

long hair.

 Do not operate the equipment while barefoot or when

wearing sandals or similar lightweight footwear. Wear

protective footwear that will protect your feet and improve

your footing on slippery surfaces.

 Exercise caution to avoid slipping or falling.

 Alwaysweareyeprotectionwithsideshieldsmarked

to comply with ANSI Z87.1. Following this rule will re-

duce the risk of serious personal injury.

 Use only recommended accessories. The use of im-

proper accessories may cause risk of injury.

 Check damaged parts. Before further use of the product,

a guard or other part that is damaged should be care-

fully checked to determine that it will operate properly

and perform its intended function. Check for alignment

of moving parts, binding of moving parts, breakage of

parts, mounting, and any other conditions that may af-

fect its operation. A guard or other part that is damaged

must be properly repaired or replaced by an authorized

service center to avoid risk of personal injury.

 Never leave product running unattended. Turn power

off. Don’t leave product until it comes to a complete stop.

Keep the motor free of grass, leaves, or grease to

reduce the chance of a fire hazard.

 Follow manufacturer’s recommendations for safe

loading, unloading, transport, and storage of machine.

 Keep product dry, clean, and free from oil and grease.

Always use a clean cloth when cleaning. Never use brake

fluids, gasoline, petroleum-based products, or any sol-

vents to clean product.



Check the work area before each use. Remove all

objects such as rocks, broken glass, nails, wire, or string

which can be thrown or become entangled in the

machine.

Do not use product if switch does not turn it off. Have

switch replaced by an authorized service center.

 Avoid dangerous environment. Don’t expose to rain.

Keep work area well lit.

 Do not abuse the cord. Never use the cord to carry the

product or to disconnect the plug from an outlet. Keep

cord away from heat, oil, sharp edges, or moving parts.

Replace damaged cords immediately. Damaged cords

increase the risk of electric shock.

 Ground Fault Circuit Interrupter (GFCI) protection

should be provided on the circuit(s) or outlet(s) to be

used for the product. Receptacles are available having

built-in GFCI protection and may be used for this measure

of safety.

 This pressure washer is not recommended for use

with an extension cord. If an extension cord must be

used, please make sure it is in good condition. When

using an extension cord, be sure to use one heavy enough

to carry the current your product will draw. A wire gauge

size (A.W.G.) of at least 12 is recommended for an ex-

tension cord 25 feet or less in length. If in doubt, use the

next heavier gauge. The smaller the gauge number, the

heavier the cord. An undersized cord will cause a drop in

line voltage resulting in loss of power and overheating.

 WARNING: Use outdoor extension cords marked SW-A,

SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOWA.

These cords are rated for outdoor use and reduce the risk

of electric shock.

 Inspect extension cords periodically and replace if

damaged. Keep handles dry, clean, and free from oil or

grease.

 Never direct a water stream toward people or pets,

or any electrical device.

Before starting any cleaning operation, close doors

and windows. Clear the area to be cleaned of debris,

toys, outdoor furniture, or other objects that could create

a hazard.

SPECIFIC SAFETY RULES

4 — English

Make sure minimum clearance of 3 feet is maintained

from combustible materials.

Never spray close to the surface to be cleaned, as you

can damage the surface.

After stopping the motor, always pull the trigger on the

trigger handle to relieve stored pressure in the high

pressure hose. Failure to do so could result in serious

personal injury.

Ensure the high pressure hose is properly connected

before using the product.

 Connect pressure washer only to an individual branch

circuit.

Hold the trigger handle securely with both hands. Ex-

pect the trigger handle to move when the trigger is pulled

due to reaction forces. Failure to do so could cause loss

of control and injury to yourself and others.

For outdoor use only.

Save these instructions. Refer to them frequently and

use them to instruct other users. If you loan someone this

product, loan them these instructions also.

 Do not use acids, alkalines, solvents, flammable ma-

terial, bleaches, or industrial grade solutions in this

product. These products can cause physical injuries to

the operator and irreversible damage to the machine.

 WARNING: High pressure jets can be dangerous if

subject to misuse. The jet must not be directed at per-

sons, animals, electrical devices, or the machine itself.

 Keep the motor away from flammables and other

hazardous materials.

 Check bolts and nuts for looseness before each use. A

loose bolt or nut may cause serious motor problems.



Before storing, allow the motor to cool.

When servicing use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

ONLY use cold water.

Never pick up or carry the machine while the motor

is running.

Never start the machine if ice has formed in any part of

the equipment.

SPECIFIC SAFETY RULES

5 — English

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

Wet Conditions Alert

Do not expose to rain or use in damp locations, and never direct

a water stream toward any electrical device.

Risk of Injection

To reduce the risk of injection or injury, never direct a water stream

towards people or pets or place any body part in the stream. Leak-

ing hoses and fittings are also capable of causing injection injury.

Do not hold hoses or fittings.

Risk of Explosion

Do not spray flammable liquids. Flammable liquids and their vapors

are explosive and can cause severe burns or death.

Kickback

To reduce the risk of injury from kickback, hold the spray wand

securely with both hands when the machine is on.

Electric Shock Do not use near electric power lines or receptacle outlets.

Chemical Burns

To reduce the risk of injury or damage, DO NOT USE ACIDS,

ALKALINES, BLEACHES, SOLVENTS, FLAMMABLE MATERIAL,

OR INDUSTRIAL GRADE SOLUTIONS in this product.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

SYMBOLS

6 — English

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

Alternating Current Type of current

No Load Speed Rotational speed, at no load

.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute

SYMBOLS

7 — English

GROUNDING INSTRUCTIONS

This product must be grounded. In the event of a malfunction

or breakdown, grounding provides a path of least resistance

for electric current to reduce the risk of electric shock.

This product is equipped with an electric cord having an

equipment-grounding conductor and a grounding plug. The

plug must be plugged into a matching outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

Do not modify the plug provided. If it will not fit the outlet,

have the proper outlet installed by a qualified electrician.

WARNING:

Improper installation of a grounded plug increase the

risk of electric shock. When repair or replacement of the

cord or plug is required, take the tool to an authorized

service center.

Check with a qualified electrician or service personnel if the

grounding instructions are not completely understood, or if

in doubt as to whether the product is properly grounded.

Repair or replace a damaged or worn cord immediately.

This product is for use on a nominal 120 V circuit and has a

grounding plug similar to the plug illustrated in figure 2. Only

connect the product to an outlet having the same configura-

tion as the plug. Do not use an adapter with this product.

GROUND FAULT CIRCUIT INTERRUPTER

See Figure 2.

This unit is equipped with a Ground Fault Circuit Interrupter

(GFCI), which guards against the hazards of ground fault

currents. An example of ground fault current is the current

that would flow through a person who is using an appliance

with faulty insulation and, at the same time, is in contact

with an electrical ground such as a plumbing fixture, wet

floor, or earth.

GFCI plugs do not protect against short circuits, overloads,

or shocks.

NOTE: To ensure readiness for use, press the reset button

each time you connect the pressure washer to the power

supply.

The GFCI plug can be tested with the TEST and RESET

buttons.

To test:

Press the TEST button. You will hear a “click” sound and

the LED light will go out.

To restore power, press the RESET button. The LED light

will illuminate to indicate power has been restored.

Perform this test monthly to ensure proper operation of the

GFCI.

To reduce the risk of electric shock the supervi-

sory circuit must be operated before an appliance is

plugged into any receptacle on the device.

EXTENSION CORDS

When using a power tool at a considerable distance from

a power source, be sure to use an extension cord that has

the capacity to handle the current the product will draw. An

undersized cord will cause a drop in line voltage, possibly

resulting in overheating, loss of power, and/or circuit

breaker or GFCI tripping. Use the chart to determine the

minimum wire size required in an extension cord. Only round

jacketed cords listed by Underwriter’s Laboratories (UL)

should be used.

When working outdoors with a product, use an extension

cord that is designed for outside use. This type of cord is

designated with “WA” or “W” on the cord’s jacket.

Before using any extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

It is possible to tie the extension cord and power cord in a

knot to prevent them from becoming disconnected during

use. Make a knot, then connect the plug end of the power

cord into the receptacle end of the extension cord. This

method can also be used to tie two extension cords together.

NOTE: This pressure washer is not recommended for

use with an extension cord. If using an extension cord,

arrange a drip loop to avoid the possibility of the tool

plug getting wet (see page 2).

USE ONLY THIS SIZE EXTENSION CORD WHEN USING

THIS PRODUCT:

Cord Length Wire Size (A.W.G.)

25 ft. 12

50 ft. Not Allowed

NOTE: A.W.G. = American Wire Gauge

WARNING:

Keep the extension cord clear of the working area.

Position the cord so that it will not get caught on

lumber, tools, or other obstructions while you are working

with a power tool. Failure to do so can result in serious

personal injury.

WARNING:

Check extension cords before each use. If damaged

replace immediately. Never use the product with a

damaged cord since touching the damaged area could

cause electrical shock resulting in serious injury.

ELECTRICAL CONNECTION

This product has a precision-built electric motor. It should be

connected to a power supply that is nominal 120V/60Hz

AC (typical U.S. household circuit). Do not operate this

product on direct current (DC). A substantial voltage drop

will cause a loss of power and the motor will overheat. If

the product does not operate when plugged into an outlet,

double-check the power supply.

ELECTRICAL

8 — English

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

PRODUCT SPECIFICATIONS

Maximum Pounds Per Square Inch* ......................................................................................................................... 2,300 psi

Maximum Gallons Per Minute ....................................................................................................................................1.2 GPM

Input ............................................................................................................................nominal 120V/60Hz AC only, 13 Amps

*Max. rating determined by PWMA Standard PW101

KNOW YOUR PRESSURE WASHER

See Figure 3.

The safe use of this product requires an understanding of

the information on the product and in this operator’s manual

as well as a knowledge of the project you are attempting.

Before use of this product, familiarize yourself with all op-

erating features and safety rules.

AUTOMATIC SOAP INJECTION SYSTEM

Pour pressure washer detergent into the soap tank to apply

detergent quickly and easily to your cleaning project. Use

of the soap nozzle will activate the soap injector at a 20:1

dilution ratio.

GFCI PLUG

The pressure washer is equipped with a GFCI plug to guard

against the hazards of ground fault currents. This plug does

not protect against short circuits, overloads, or shocks.

ON/OFF SWITCH

This switch turns the pressure washer on and off.

POWER CORD STORAGE BRACKET

Store the power cord on the convenient storage bracket

when the pressure washer is not in use. Easily secure and

release with the attached bungee cord.

TRIGGER HANDLE

The trigger handle has a gripping surface that provides

added control of the spray wand and helps reduce fatigue.

TRIGGER WITH LOCK-OUT

Pulling the trigger releases a stream of water for high pres-

sure cleaning. The lock-out provides protection against

unauthorized use.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-525-2579 for assistance.

PACKING LIST

Electric Pressure Washer

Handle

Trigger Handle

Spray Wand

25 ft. High Pressure Hose

Nozzles (15º, Turbo, Soap)

Operator’s Manual

FEATURES

ASSEMBLY

9 — English

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

Do not connect to power supply until assembly is com-

plete. Failure to comply could result in accidental starting

and possible serious personal injury.

INSTALLING THE WHEELS

See Figure 4.

 Locate the axles, hitch pins, and wheels.

 Slide the axle through the hole in the center of the wheel.

 Lift the machine and slide the axle into the wheel mount-

ing hole in the machine base as shown.

 Push the hitch pin into the hole on the end of the axle to

secure the wheel assembly.

NOTE: The hitch pin should be pushed into the axle until

the center of the pin rests on top of the axle.

 Repeat with the second wheel.

INSTALLING THE HANDLE

See Figure 5.

CAUTION:

Be careful to avoid pinching your fingers or hands when

installing the handle onto the frame.

Push and hold the push-pin button on the side of the handle

as you slide the handle onto the frame.

NOTE: Before use, pull the handle up until the lock button

snaps through the locking slots to secure the handle in place.

CONNECTING THE SPRAY WAND TO THE

TRIGGER HANDLE

See Figure 6.

 Place the threaded end of the spray wand in the connec-

tor on the end of the trigger handle.

 Turn the connector until it stops to secure the spray wand

in place.

CONNECTING THE HIGH PRESSURE HOSE

TO THE TRIGGER HANDLE

See Figure 7.

 Remove the high pressure hose from the hose reel.

 Screw the collar on the high pressure hose onto the trigger

handle inlet coupler by turning the hose collar clockwise.

Tighten securely.

NOTE: Be careful to avoid cross-threading, which can

cause the trigger handle to leak during use.

 Pull on the hose to be certain it is properly secured.

CONNECTING THE HIGH PRESSURE HOSE

TO THE PUMP

See Figure 8.

 Completely uncoil and straighten the high pressure hose

to prevent kinks.

NOTE: See Using the High Pressure Hose in

Operation

for more information about using the high pressure hose.

 Align the collar on the hose to the threaded outlet on the

pump.

 Install the high pressure hose collar onto the threaded

outlet.

 Turn the collar clockwise to tighten the hose securely to

the pump.

NOTE: Be careful to avoid cross-threading, which can

cause the hose to leak during use.

 Pull on the hose to be certain it is properly secured.

CONNECTING THE GARDEN HOSE TO THE

PRESSURE WASHER

See Figure 9.

NOTICE:

Always observe all local regulations when connecting

hoses to the water main. Some areas have restrictions

against connecting directly to public drinking water sup-

ply to prevent the feedback of chemicals into the drinking

water supply. Direct connection through a receiver tank

or backflow preventer is usually permitted.

ASSEMBLY

10 — English

WARNING:

Do not allow familiarity with the product to make you care-

less. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

The water supply must come from a water main. NEVER use

hot water or water from pools, lakes, etc. Before connecting

the garden hose to the pressure washer:

 Run water through the hose for 30 seconds to clean any

debris from the hose.

 Inspect the screen in the water intake.

 If the screen is damaged, do not use the machine until

the screen has been replaced.

 If the screen is dirty, clean it before connecting the garden

hose to the machine.

To connect the garden hose to the machine:

 Completely uncoil the garden hose or remove completely

from reel to prevent kinks.

NOTE: There must be a minimum of 10 feet of unrestricted

hose between the pressure washer intake and the hose

faucet or shut off valve (such as a “Y” shut off connector).

 With the hose faucet turned completely off, attach the

end of the garden hose to the water intake. Tighten by

hand.

NOTICE:

Do not run the pressure washer without water supply

connected and turned on, as this may damage the high

pressure seals and decrease pump life. Completely

unwind the hose from its reel or coil and make sure the

hose is not being restricted by tires, rocks, or any other

objects that may lessen or prevent water flow to the

pressure washer.

ASSEMBLY

OPERATION

WARNING:

Never direct a water stream toward people or pets, or

any electrical device. Failure to follow these instructions

could result in serious injury, electric shock, or death.

NOTICE:

Before each use, inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts

are replaced. Please call customer service or contact an

authorized service center for assistance.

APPLICATIONS

You may use this tool around the house for cleaning most

small to large horizontal or vertical exterior surfaces, smaller

exterior objects and structures, and outdoor equipment and

tools.* You can:

11 — English

NOTICE:

Routinely make a visual inspection of the pump and

motor during use. If you notice any lubricant leaking

around the pump or motor seals, stop using the pres-

sure washer immediately. Contact customer service or

a qualified service center for repair. Failure to do so may

cause property damage.

To stop the motor:

Put the on/off switch in the OFF position.

 Pull trigger to release water pressure.

NOTE: The pressure washer may be on and the system

may have pressure even when the pump and/or motor

cannot be heard running. Always use caution around the

pressure washer.

USING THE TRIGGER HANDLE

See Figure 11.

WARNING:

Hold the trigger handle securely with both hands. Expect

the trigger handle to move when the trigger is pulled due

to reaction forces. Failure to do so could cause loss of

control and injury to yourself and others.

 Pull back and hold the trigger to operate the pressure

washer.

 Release the trigger to stop the flow of water through the

nozzle.

To engage the lock out:

 Push up on the lock out until it clicks into the slot.

To disengage the lock out:

 Push the lock out down and into its original position.

Start with the nozzle 1–2 ft. away from the cleaning surface

and carefully approach the surface just until the desired

level of cleaning is achieved. If the spray is too close it can

damage the cleaning surface.

SELECTING THE RIGHT NOZZLE FOR THE JOB

See Figure 12.

Each of the nozzles has a different spray pattern. Before

starting any cleaning job, determine the best nozzle for the

job. Refer to the Nozzle Selection Guide for more informa-

tion about which nozzle to choose.

 Clean or remove mold and mildew from weathered decks,

driveways, patios, walkways, sidewalks, etc.

 Remove dirt from various exterior vertical surfaces such

as house exteriors, siding, fences, brick, concrete or stone

walls, etc.

 Wash boats, outdoor furniture, powered or non-powered

garden equipment, gutters, window screens, grills, play-

ground equipment, etc.

*Always test in an inconspicuous area first.

STARTING AND STOPPING THE PRESSURE

WASHER

See Figure 10.

NOTICE:

Do not run the pressure washer without water supply

connected and turned on, as this may damage the high

pressure seals and decrease pump life. Completely

unwind the hose from its reel or coil and make sure the

hose is not being restricted by tires, rocks, or any other

objects that may lessen or prevent water flow to the

pressure washer.

Before starting the motor:

 Connect all hoses.

NOTE: Make sure the pressure washer’s water intake

screen is in place and unclogged before connecting

garden hose.

 Turn on the garden hose then pull the trigger to relieve air

pressure; hold the trigger until a steady stream of water

appears.

NOTE: Make sure the faucet is turned on fully and that

there are no kinks or leaks in the hose.

To start the motor:

 With the on/off switch in the OFF position, connect the

pressure washer to the power supply.

NOTE: If using an extension cord, make sure to arrange

a drip loop as described on page 2.

WARNING:

To reduce the risk of electrocution, keep all connections

dry and off the ground. Do not touch plug with wet hands.

 Press the reset button on the pressure washer’s plug to

make sure the unit is ready for operation.

 Put the on/off switch in the ON position to start the motor.

OPERATION

12 — English

Turn off the pressure washer, disconnect from power

supply, and shut off the water supply. Pull trigger to

release water pressure.

 Engage the lock-out on the trigger handle by pushing up

on the lock-out until it clicks into the slot.

 Pull back and hold the quick-connect collar.

 Remove the nozzle by pulling it from the quick-connect

collar. Place nozzle in the nozzle storage area on the top

of the machine.

USING THE HIGH PRESSURE HOSE

WARNING:

Injection hazard. Fully unwrap and straighten high pres-

sure hose prior to and during each use and do not allow

it to become kinked. The high pressure hose features an

outer covering that provides strength to the hose. If the

outer covering becomes damaged, stop using the hose

and replace it immediately. A kinked or damaged hose

can develop a high pressure leak and result in a possible

injection or other serious personal injury.

To prevent damage to the outer covering:

 Inspect the hose before every use.

WARNING:

NEVER remove nozzles without first turning off the motor,

disconnect from power supply, relieving the water pres-

sure in the trigger handle, and locking the lock out on the

trigger handle. NEVER point the nozzle at your face or at

others. The quick-connect feature contains small springs

that could eject the nozzle with some force. Failure to

follow these instructions could result in an eye injury or

other serious personal injury.

To connect a nozzle to the spray wand:

 Turn off the pressure washer, disconnect from power

supply, and shut off the water supply. Pull trigger to

release water pressure.

Engage the lock-out on the trigger handle by pushing up

on the lock-out until it clicks into the slot.

Pull back the quick-connect collar.

Push the nozzle into place in the spray wand.

Push the collar forward so that the nozzle is secured

properly. Check to see that the nozzle is secure.

To disconnect a nozzle from the spray wand once the

cleaning job is complete:

NOZZLE SELECTION GUIDE

HIGH PRESSURE

(NO SOAP WHEN USING THESE NOZZLES)

LOW PRESSURE

(FOR SOAP OR

GENTLE RINSE)

Turbo Nozzle

15º

Blue or Black

Soap Nozzle

Concrete, Brick, Masonry

  

Siding, Gutters, House

 

Fencing, Deck, Patio

 

Lawn Equipment, Boat, RV

 

 Recommended Nozzle  Use With Caution for Certain Applications

OPERATION

13 — English

OPERATION

 Fully unwrap and straighten hose before use.

 Do not allow the high pressure hose to be kinked.

 Keep hose away from hot surfaces and sharp edges.

 Do not pull unit by high pressure hose.

 Do not allow hose to be crushed or wrapped around

objects.

WASHING WITH DETERGENT

See Figures 13-14.

As sold, this unit is designed for use with “downstream” pres-

sure washer detergents. To convert for use with “upstream”

detergents, contact customer service or an authorized service

center for more information.

NOTICE:

USE ONLY DETERGENTS DESIGNED FOR PRES-

SURE WASHERS. Do not use household detergents,

acids, alkalines, bleaches, solvents, flammable material,

or industrial grade solutions, which can damage the

pump or cause property damage. Many detergents may

require mixing prior to use. Prepare cleaning solution

as instructed on the solution bottle. Always test in an

inconspicuous area before beginning.

 Disconnect pressure washer from power supply.

 Pour detergent in the soap tank. Use a funnel, if needed,

to prevent accidental spilling of the detergent outside

the tank. If any detergent is spilled during the filling

process, make sure the unit is cleaned and dried before

proceeding.

NOTE: The machine setting of this unit is 20:1, which usu-

ally allows the use of 1 gallon pressure washer detergent

without further dilution. Check your detergent instructions

to be sure additional dilution is not necessary.

 Install the blue or black soap nozzle on the spray wand.

 Connect unit to power supply and turn the pressure

washer on.

 Squeeze the trigger and wait approximately 5 seconds

for the detergent to appear.

 Spray the detergent on a dry surface using long, even,

overlapping strokes. To prevent streaking, do not allow

detergent to dry on the surface.

Before shutting off the motor:

 Fill the soap tank with clean water.

 Spray the clear water through the spray wand until the

tank is empty.

 If any detergent remains in the spray, repeat with a second

tank of clean water.

 Shut off the motor.

NOTE: Shutting off the motor will not relieve pressure in the

system. Pull trigger to release water pressure.

RINSING WITH THE PRESSURE WASHER

 Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

 Engage the lock out on the trigger handle by pushing up

on the lock out until it clicks into the slot.

 Remove the soap nozzle and place it in the nozzle storage

area on the machine.

 Select the right nozzle for the job. See the chart shown

earlier in the manual to select the appropriate nozzle.

 Start at the top of the area to be rinsed and work down,

overlapping the strokes.

USING PUMP PROTECTOR

See Figure 15.

Regular use of a commercially available pump protector

prolongs the life of the pressure washer by removing hard

water mineral deposits, lubricating pump seals and pistons,

and preventing freeze damage. Pump protector should be

added to the unit after every use and before storage. Pump

protector can be purchased at the retailer where you pur-

chased your pressure washer, or by calling customer service.

The instructions that follow are typical for adding pump pro-

tector but you should always verify the specific instructions

provided by the manufacturer of the pump protector used.

 Turn off the pressure washer motor and shut off the water

supply. Pull trigger to release water pressure.

 Disconnect garden hose and high pressure hose.

 Unscrew threaded top from pump protector bottle and

remove paper seal from bottle. Reinstall top on bottle and

tighten securely.

NOTE: The rubber seal should remain inside the threaded

top. If it comes out, be sure to replace before reinstalling

the top.

 Remove bottle cap and attach threaded end of bottle

securely to pressure washer pump water intake.

 Squeeze bottle to inject contents into pump.

 Pump is protected when the protector fluid exits the pump

outlet.

POWER CORD STORAGE

See Figure 16.

When it is not in use, the power cord may be coiled and

suspended from the storage hook on the handle.

To secure the power cord in place, use the attached bungee

cord.

MOVING THE PRESSURE WASHER

See Figure 17.

NOTE: Never lift or carry this product using the handle and

never place the unit in any position other than upright on

its wheels.

14 — English

OPERATION

 Turn the pressure washer off. Point nozzle in a safe direc-

tion and pull trigger to release water pressure.

 Tilt the machine toward you slightly until it balances on

the wheels then roll the machine to the desired position.

Do not tilt forward or sideways when moving.

 DO NOT attempt to move the unit by pulling on any of

the hoses.

MAINTENANCE

WARNING:

Before inspecting, cleaning, or servicing the machine,

shut off motor, wait for all moving parts to stop, discon-

nect unit from power supply, and pull trigger to release

water pressure. Failure to follow these instructions can

result in serious personal injury or property damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes, resulting in possible

serious injury.

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts could create a hazard or cause

product damage.

NOTICE:

Periodically inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts

are replaced. Please call customer service or contact an

authorized service center for assistance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken, or

destroy plastic which could result in serious personal

injury.

POWER SUPPLY CORD REPLACEMENT

If replacement of the power supply cord is necessary, this

must be done by an authorized service center in order to

avoid a safety hazard.

PUMP LUBRICATION

The pump on this unit is lubricated with a sufficient amount

of high grade lubricant for the life of the unit under normal

operating conditions. Therefore, no further lubrication is

required.

PUMP MAINTENANCE

Routinely make a visual inspection of the pump. If you notice

any leaking of lubricant around the pump seals, take the

pressure washer to an authorized service center for repair.

There are no user serviceable parts to the pressure washer

pump. Any attempt to service or alter the pump may dam-

age the pressure washer and void your product warranty.

NOZZLE MAINTENANCE

See Figure 18.

Excessive pump pressure (a pulsing sensation felt while

squeezing the trigger) may be the result of a clogged or

dirty nozzle.

 Turn off the pressure washer, disconnect from power

supply, and shut off the water supply. Pull trigger to

release water pressure.

 Remove the nozzle from the spray wand.

15 — English

WARNING:

NEVER remove nozzles without first turning off the mo-

tor, disconnecting from power supply, relieving the water

pressure in the trigger handle, and locking the lock out

on the trigger handle. NEVER point the nozzle at your

face or at others. The quick-connect feature contains

small springs that could eject the nozzle with some force.

Failure to follow these instructions could result in an eye

injury or other serious personal injury.

 To free any foreign materials clogging or restricting the

nozzle, blow out or remove debris with a straightened

paper clip or fine needle (not included).

 Using a garden hose, flush debris out of nozzle by back

flushing (running the water through the nozzle backwards

or from the outside to the inside).

 Reconnect the nozzle to the spray wand.

 Turn on the water supply and start the motor.

STORING THE PRESSURE WASHER

See Figures 19-20.

NOTE: Regular use of pump protector will give you better

performance of the unit and increase the life of the pump.

Store in a dry, covered area where the weather can’t damage it.

It is important to store this product in a frost-free area. Al-

ways empty water from all hoses, the pump, and the soap

tank before storing.

 Make sure the on/off switch is in the OFF position.

 Disconnect both the high pressure hose and the garden

hose from the pump.

 Tilt the unit as shown to allow any remaining water in the

pump to drain from the water inlet.

NOTICE:

If the location where your pressure washer is stored will

fall below 32°F, the use of a pump protector is required

before storing to prevent freeze damage. Freeze damage

will void your warranty.

 Store the unit and accessories in an area that does not

reach freezing temperatures. Do not store near furnace or

other sources of heat that could dry out the pump seals.

MAINTENANCE

This product has a Three-year Limited Warranty for personal,

family, or household use (90 days for business or commercial use).

For warranty details, visit www.ryobitools.com

or call (toll free) 1-800-525-2579.

16 — English

PROBLEM POSSIBLE CAUSE SOLUTION

Pressure washer does not start

when trigger is depressed

Power cord not connected to power

source.

The on/off switch is in the OFF

position.

GFCI is tripped.

House/shop circuit breaker is tripped.

Water pressure in hose.

Receptacle is bad.

Connect the power cord to a live

120V AC, 60 Hz AC receptacle.

Put the on/off switch in the ON

position.

Press reset button on the GFCI

plug.

Reset house/shop breaker. Make

sure pressure washer is connected

to an individual branch circuit only.

If using an extension cord, make

sure it is heavy enough to carry the

current of the pressure washer.

Squeeze trigger to relieve water

pressure.

Try another receptacle.

Pump doesn’t produce pressure Inadequate water supply.

Spray wand leaks.

Nozzle is clogged.

Pump is faulty.

Air in line.

Water inlet filter is clogged or dirty.

Provide adequate water flow.

Check connections and / or

replace wand.

Clean nozzle.

Contact authorized service center.

Squeeze trigger on spray wand to

remove air from line.

Remove the water inlet filter, rinse

with warm water, then replace in

unit.

Machine doesn’t reach high

pressure

Diameter of garden hose is too small.

Water supply is restricted.

Not enough inlet water.

Hose is leaking.

Kink in hose.

Replace with 3/4 in. garden hose.

Check garden hose for kinks, leaks,

and blockages.

Open water source full force.

Replace hose.

Eliminate kinks in hose.

No detergent Soap tank is empty.

Water supply is inadequate or

clogged.

Wrong nozzle is attached.

Add additional detergent to tank.

Check garden hose for kinks, leaks

and blockages.

Attach blue or black soap nozzle.

Wand leaks O-ring needs replacing. Replace o-ring. If this does not

correct the problem, contact

your authorized service center to

purchase a new wand.

TROUBLESHOOTING

La page charge ...

Ryobi RY142300 Le manuel du propriétaire

Marque: Ryobi

Modèle: RY142300

Catégorie: Nettoyeurs haute pression

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi RY142300 Owner's manual
español: Ryobi RY142300 El manual del propietario

Ryobi RY142300 Le manuel du propriétaire

Ryobi RY142300 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents