Poulan Pro PR100 Le manuel du propriétaire

OWNER'S MANUAL

MODEL NUMBER:

PR100

SNOW THROWER

Always Wear Eye Protection During Operation

IMPORTANT MANUAL Do Not Throw Away

WARNING:

Read the Owner's Manual and

fol low all Warnings and Safety

In struc tions. Fail ure to do so

can result in serious injury.

115 87 62-32 Rev. 2 07.11.17 CL Printed in the U.S.A.

Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.

The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.

2

Safe Operation Practices for Walk-Behind Snow Throwers

IMPORTANT: This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury.

(c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

(d) Never fill containers inside a vehicle or on a truck or

trailer bed with a plastic liner. Always place containers

on the ground, away from your vehicle, before filling.

(e) When practical, remove gas-powered equipment

from the truck or trailer and refuel it on the ground.

If this is not possible, then refuel such equipment

on a trailer with a portable container, rather than

from a gasoline dispenser nozzle.

(f) Keep the nozzle in contact with the rim of the fuel

tank or container opening at all times, until refueling

is complete. Do not use a nozzle lock-open device.

(g) Replace gasoline cap securely and wipe up spilled

fuel.

(h) If fuel is spilled on clothing, change clothing

immediately.

5. Use extension cords and receptacles as specified by

the manufacturer for all units with electric drive motors

or electric starting motors.

6. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

7. Always wear safety glasses or eye shields during op-

eration or while performing an adjustment or repair to

protect eyes from foreign objects that may be thrown

from the machine.

8. Use ear protectors to avoid damage to hearing.

Training

1. Read, understand and follow all instructions on the

machine and in the manual(s) before operating this

unit. Be thoroughly familiar with the controls and the

proper use of the equipment. Know how to stop the

unit and disengage the controls quickly.

2. Never allow children to operate the equipment. Never

allow adults to operate the equipment without proper

instruction.

3. Keep the area of operation clear of all persons, par-

ticularly small children.

4. Exercise caution to avoid slipping or falling, especially

when operating the snow thrower in reverse.

Preparation

1. Thoroughly inspect the area where the equipment is

to be used and remove all doormats, sleds, boards,

wires, and other foreign objects.

2. Ensure the control bar is released before starting the

engine.

3. Do not operate the equipment without wearing adequate

winter garments. Avoid loose fitting clothing that can

get caught in moving parts. Wear footwear that will

improve footing on slippery surfaces.

4. Handle fuel with care; it is highly flammable

(a) Use an approved fuel container.

(b) Never add fuel to a running engine or hot engine.

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac tured to

give best possible dependability and per for mance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We

have competent, well-trained tech ni cians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower prop er ly.

Always observe the “SAFETY RULES”.

Look for this symbol to point out im por tant

safety precautions. It means CAUTION!!! BE-

COME ALERT!!! YOUR SAFE TY IS IN VOLVED.

WARNING: Always disconnect spark plug wire

and place it where it can not con tact plug in order

to pre vent ac ci den tal start ing when setting up,

trans port ing, ad just ing or making re pairs.

WARNING: This snow thrower is for use on

sidewalks, driveways and other ground level sur-

faces. Caution should be exercised while using

on sloping surfaces. Do not use snow thrower

on surfaces above ground level such as roofs

of residences, garages, porch es or other such

structures or buildings.

WARNING: Engine exhaust, some of its con stit u-

ents, and certain vehicle com po nents contain or

emit chem i cals known to the State of Cal i for nia

to cause can cer and birth defects or oth er re pro-

duc tive harm.

CAUTION: Muffler and other engine parts become

extremely hot during operation and remain hot

after engine has stopped. To avoid severe burns

on contact, stay away from these areas.

WARNING: Snow throwers have ex posed rotating

parts, which can cause severe injury from contact,

or from material thrown from the discharge chute.

Keep the area of operation clear of all persons,

small children and pets at all times including

startup.

3

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in maintaining, caring for

and using your snow thrower.

• Follow the instructions under “Maintenance” and “Stor-

age” sec tions of this manual.

PRODUCT SPECIFICATIONS

Gasoline Capacity 0.31 Gallon (1,17 Liters)

and Type: Unleaded Regular only

Oil Type SAE 30 (above 50°F)

(API SJ–SN): SAE 5W-30 or 10W-30

(32° to 50°F)

SAE 5W-30 (below 32°F)

Oil Capacity: 16 Ounces (0,47 Liters)

Spark Plug: F6RTC

Gap: 0.030" (0,762 mm)

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND

ON A DECAL ATTACHED TO THE REAR OF THE SNOW

THROWER HOUSING (Figure 1).

YOU SHOULD RECORD BOTH SERIAL NUMBER AND

DATE OF PURCHASE AND KEEP IN A SAFE PLACE

FOR FUTURE REFERENCE.

Figure 1

FOR SERVICE CALL/POUR LE SERVICE APPELER

1-800-448-7543

ASSEMBLED IN U.S.A. / ASSEMBLÉ AUX ÉTATS-UNIS

MCRAE, GA 31055

000000

SERIAL NUMBER

NUMERO DE SERIE

MODEL NUMBER / NUMERO DE MODELE

PRODUCT

PRODUIT

MAINTENANCE LEVEL

NIVEAU DE MAINTENANCE

000000000 00

000000A 000000

00000000

CONFORMS TO ANSI B71.3-2005 SAFETY STANDARDS

CONFORME AUX NORMES DE SÉCURITÉ DE ANSI B71.3-2005

Operation

1. Do not put hands or feet near or under rotating parts.

Keep clear of the discharge opening at all times.

2. Exercise extreme caution when operating on or cross-

ing gravel drives, walks, or roads. Stay alert for hidden

hazards or traffic.

3. After striking a foreign object, stop the engine (motor),

disconnect the cord on electric motors, thoroughly

inspect the snow thrower for any damage, and repair

the damage before restarting and operating the snow

thrower. Remove key.

4. If the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the cause.

Vibration is generally a warning of trouble.

5. Stop the engine (motor) whenever you leave the

operating position, before unclogging the auger hous-

ing or discharge chute, and when making any repairs,

adjustments or inspections.

6. When cleaning, repairing or inspecting the snow thrower,

stop the engine and make certain the auger blades and

all moving parts have stopped. Remove key.

7. Do not run the engine indoors, except when starting

the engine and for transporting the snow thrower in or

out of the building. Open the outside doors; exhaust

fumes are dangerous.

8. Exercise extreme caution when operating on slopes.

9. Never operate the snow thrower without proper guards,

and other safety protective devices in place and working.

10. Never direct the discharge toward people or areas

where property damage can occur. Keep children and

others away.

11. Do not overload the machine capacity by attempting

to clear snow at too fast a rate.

12. Never operate the machine at high transport speeds

on slippery surfaces. Look behind and use care when

operating in reverse.

13. Disengage power to the auger blades when snow

thrower is transported or not in use.

14. Use only attachments and accessories approved by

the manufacturer of the snow thrower.

15. Never operate the snow thrower without good visibility

or light. Always be sure of your footing, and keep a firm

hold on the handles. Walk; never run.

16. Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating auger blades

inside the discharge chute is the most common

cause of injury associated with snow throwers.

Never use your hand to clean out the discharge

chute.

To clear the chute:

1. SHUT THE ENGINE OFF!

2. Wait 10 seconds to be sure the auger blades have

stopped rotating.

3. Always use a clearing tool at least 15 inches long.

Maintenance and Storage

1. Check shear bolts and other bolts at frequent intervals

for proper tightness to be sure the equipment is in safe

working condition.

2. Never store the machine with fuel in the fuel tank inside

a building where ignition sources are present such as

hot water heaters, space heaters, or clothes dryers.

Allow the engine to cool before storing in any enclosure.

3. Always refer to operator’s manual for important details

if the snow thrower is to be stored for an extended

period.

4. Maintain or replace safety and instruction labels, as

necessary.

5. Run the machine a few minutes after throwing snow

to prevent freeze-up of the collector/impeller.

4

OPERATION ............................................................ 7-11

MAINTENANCE ..................................................... 12-16

STORAGE ................................................................... 17

TROUBLESHOOTING ................................................ 18

REPAIR PARTS ..................................................... 20-29

SAFETY RULES ........................................................ 2-3

PRODUCT SPECIFICATIONS ...................................... 3

CUSTOMER RESPONSIBILITIES ................................ 3

SAFETY AND INSTRUCTIONAL DECALS ................. 4

SETUP........................................................................ 5-6

TABLE OF CONTENTS

KNOW YOUR SNOW THROWER

READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Com-

pare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.

Save this manual for future reference.

These symbols may appear on your snow thrower or in literature supplied with the product. Learn and under-

stand their meaning.

IMPORTANT: Safety and instruction decals are located near areas of potential danger. Replace damaged decals.

READ AND FOLLOW ALL SAFETY INFORMATION

AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT.

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

DANGER

OR WARNING

CHOKE

PRIMER

2

IGNITION KEY.

INSERT TO START

AND RUN,

PULL OUT TO STOP.

EAR PROTECTION

RECOMMENDED

5

1. Unfolding the Handle

Procedure

1. Loosen the two handle knobs and pull out the two

handle bolts until you can move the handle freely and

rotate the handle to the operating position (Figure 2).

2. Tighten the handle knobs until they are snug (Figure 3).

Figure 3

1. Handle knobs 2. Handle bolt

Figure 2

2

1

2. Installing the Discharge Chute

Procedure

1. Install the chute deflector to the discharge chute using

bolts and, washer, nut, deflector knob and cap plunger

(Figure 4).

2. Install the discharge chute to the chute base using

three screws and nuts.

IMPORTANT: Do not overtighten the flange nuts; other-

wise you may damage the discharge chute.

Figure 4

1. Deflector

2. Carriage bolts

3. Flange nuts 5/16-18

4. Washer

5. Knob

6. Discharge chute

7. Carriage Bolt

8. Shoulder Bolt

9. Flange nuts 1/4-20

10. Cap Plunger

2

7

6

3

8

4

9

5

10

1

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure Description Qty. Use Tools Required

1.

No parts required – Unfold the handle. –

2.

Carriage bolts

Shoulder Bolt

Flange nuts

Washer

Knob

Cap Plunger

Chute

Deflector

4

1

4

1

Install the discharge chute.

1/2" Wrench

7/16" Wrench

3/8" Wrench

6

Product Overview

Figure 6

1. Discharge chute

2. Chute deflector handle

3. Fuel tank cap

4. Control bar

5. Recoil start handle

6. Primer

7. Choke lever

8. Electric-start button

(if equipped)

9. Oil drain plug

10. Drive belt cover

*11. Oil fill cap/dipstick

12. Ignition key

13. Chute deflector

5

2

6

10

1

7

*11

9, *11

3

8

12

4

13

* Dipstick location may vary depending on engine type.

3. Filling the Engine with Oil

ENGINE

See engine manual.

LUBRICATION

NOTE: SAE 10W30 or SAE 5W30 oil is acceptable for

use in cold temperatures if engine is difficult to start.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)

improve starting in cold weather, these multi-viscosity oils

will result in increased oil consumption when used above

32°F. Check your engine oil level more frequently to avoid

possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least

once a year if the snow thrower is not used for 25 hours

in one year.

Check the crankcase oil level before starting the engine

and after each five (5) hours of continuous use. Tighten oil

fill cap / dipstick securely each time you check the oil level.

1. Move the snowthrower to a level surface.

2. Clean around the dipstick (Figure 5).

NOTE: Dipstick location may vary depending on engine

type.

3. Remove either side mounted filler cap dipstick or high

oil fill dipstick and wipe it clean.

4. Insert the dipstick into the filler neck and turn clockwise

until fully seated. Then remove the dipstick by turning

it counter-clockwise.

5. Fill oil to "FULL" on dipstick with the recommended oil.

6. Securely screw in the oil filler cap/dipstick.

1. Oil filler cap/dipstick

Figure 5

1

Fill if oil is

below letter

“L” on the

¿OOHUFDS

Fill if oil

is below

“Add”

on the

GLSVWLFN

7

Operation

NOTE: Determine the left and right sides of the machine

from the normal operating position.

• Gasoline is extremely flammable and explosive.

A fire or explosion from gasoline can burn you

and others.

• To prevent a static charge from igniting the gaso-

line, place the container and/or snowthrower on

the ground before filling, not in a vehicle or on

an object.

• Fill the tank outdoors when the engine is cold.

Wipe up spills.

• Do not handle gasoline when smoking or around

an open flame or sparks.

• Store gasoline in an approved fuel container, out

of the reach of children.

• Do not tip the snowthrower with fuel in the fuel

tank.

The operation of any snow thrower can result

in foreign objects thrown into the eyes, which

can result in severe eye damage. Always wear

safety glasses or eye shields while operating

your snow thrower or performing any ad just-

ments or repairs. We recommend standard safe ty glasses

or a wide vision safety mask worn over spectacles.

IMPORTANT: Know how to operate all controls before

adding fuel or attempting to start the engine.

Filling the Fuel Tank

Fill the fuel tank with fresh, unleaded gasoline (minimum

87 AKI octane rating) (Figure 7).

IMPORTANT: Do not add oil to the gasoline.

IMPORTANT: Do not use E85 blended fuels. This engine

is not E20/E30/E85 compatible. Alternative fuels with

high alcohol content can cause hard starting, poor engine

performance, and may cause internal engine damage.

Checking the Engine Oil

Level

1. Move the snowthrower to a level surface.

2. Clean around the dipstick (Figure 8).

NOTE: Dipstick location may vary depending on engine

type.

3. Remove either side mounted filler cap dipstick or high

oil fill dipstick and wipe it clean.

4. Insert the dipstick into the filler neck and turn clockwise

until fully seated. Then remove the dipstick by turning

it counter-clockwise.

5. Fill oil to "FULL" on dipstick with the recommended oil.

6. Securely screw in the oil filler cap/dipstick.

NOTE: Running the engine with a low oil level can cause

engine damage. Always check the engine oil before start up.

NOTE: Running the engine with too much oil may cause

engine damage and excess smoke in the exhaust. Always

check the engine oil level before start up.

NOTE: For best results, purchase only the quantity of

gasoline that you expect to use in 30 days. Otherwise,

you may add fuel stabilizer to newly purchased gasoline

to keep it fresh for up to 6 months.

Figure 7

1. Oil filler cap/dipstick

Figure 8

1

Fill if oil is

below letter

“L” on the

¿OOHUFDS

Fill if oil

is below

“Add”

on the

GLSVWLFN

8

Starting the Engine

1. Push key in (Figure 9).

2. Move choke lever to left position (Figure 10).

3. Firmly push in the primer 2 times with your thumb,

holding the primer in a for a second before releasing

it each time (Figure 11).

NOTE: Remove your glove when you push in the primer

so that air cannot escape from the primer hole.

IMPORTANT: It may not be necessary to use the primer

or the choke if the engine has been running and is hot.

Excessive priming may flood the engine and prevent it

from starting.

4. Pull the recoil starter or if your snow thrower is equipped

with an electric starter, connect an extension cord to

the snow thrower and plug the other end into a three-

hole grounded 110 volt A.C. receptacle and push the

electric-start button (Figure 12).

NOTE: Use an extension cord recommended for outdoor

use that is not longer than 50 feet (15 m).

1. Primer

Figure 11

1

Figure 9

1. Key

1

Figure 12

1. Electric start button

1

1. Choke lever

Figure 10

1

9

Engaging the Auger Blades

To engage the auger blades, hold the control bar against

the handle (Figure 14).

Disengaging the Auger

Blades

To disengage the auger blades, release the control bar

(Figure 15).

The electrical cord can become damaged, causing

a shock or fire.

Thoroughly inspect the electrical cord before plug-

ging it into a power source. If the cord is damaged,

do not use it to start the snowthrower. Replace or

repair the damaged cord immediately. Contact an

Authorized Service Dealer for assistance.

IMPORTANT: Run the electric starter no more than 10

times at intervals of 5 seconds on, then 5 seconds off.

Running the electric starter extensively can overheat and

damage it. If the engine does not start after this series of

attempts, wait at least 40 minutes to allow the starter to

cool before attempting to start it again. If the engine does

not start after the second series of attempts, take the

snowthrower to an Authorized Service Dealer for service.

NOTE: If you pull the recoil handle and feel no resistance,

the starter may be frozen. Thaw out the starter before

attempting to start the snowthrower.

5. While the engine is running, move the choke lever

slowly to the right position.

6. Unplug the extension cord from the power source and

the snowthrower (Figure 12).

Unplug the power cord whenever you are not start-

ing the snowthrower.

Figure 14

1. Control bar

1

Figure 15

1. Control bar

1

1. Recoil start handle

Figure 13

1

10

Figure 16

1. Rub Area 2. Wear Areas

1

2

1

Adjusting the Discharge

Chute and Chute Deflector

To adjust the discharge chute, move deflector chute handle

left or right to desired position (Figure 18).

To raise or lower the angle of the chute deflector, loosen

the chute deflector knob on the chute deflector and move

the chute deflector up or down (Figure 18).

1. Chute deflector knob

2. Chute deflector

3. Chute handle

Figure 18

1

2

3

IMPORTANT: During initial operation there may be wear

between the auger blades and the scraper bar. Maximum

performance, both snow throwing and driving, occurs

when there is zero clearance between these two parts

(Figure 16).

During initial break-in period of the auger blades it

is normal for the auger blades to build up excessive

heat if not operated in the snow.

Do not operate without snow or water for lubricating

the auger blades. This will cause excessive heat

build up in the auger blades which could cause

damage to the auger blades and scrapper bar.

Stopping the Engine

To stop the engine, pull key out (Figure 17).

Figure 17

1. Key

11

Clearing a Clogged

Discharge Chute

Preventing Freeze-up after

Use

• Let the engine run for a few minutes to prevent moving

parts from freezing. Stop the engine, wait for all mov-

ing parts to stop, and remove ice and snow from the

snowthrower.

• Clean off any snow and ice from the base of the chute.

• Rotate the discharge chute left and right to free it from

any ice buildup.

• With the ignition key in the Off position, pull the recoil

starter handle several times or connect the electrical

cord to a power source and the snowthrower and push

the electric start button once to prevent the recoil starter

and/or the electric starter from freezing up.

• In snowy and cold conditions, some controls and mov-

ing parts may freeze. Do not use excessive force when

trying to operate frozen controls. If you have difficulty

operating any control or part, start the engine and let

it run for a few minutes.

Hand contact with the rotating auger blades

inside the discharge chute is the most common

cause of injury associated with snow throwers.

Never use your hand to clean out the discharge

chute.

To clear the chute:

1. SHUT THE ENGINE OFF!

2. Wait 10 seconds to be sure the auger blades have

stopped rotating.

3. Always use a clearing tool at least 15 inches long, not

your hands (Figure 19).

Figure 19

Operating Tips

The auger blades can throw stones, toys, and

other foreign objects and cause serious personal

injury to the operator or to bystanders.

• Keep the area to be cleared free of all objects

that the auger blades could pick up and throw.

• Keep all children and pets away from the area

of operation.

• Do not operate snow thrower if weather condi-

tions im pair visibility. Throwing snow dur ing

a heavy, windy snowstorm can blind you and

be hazardous to the safe operation of the snow

thrower.

• The best time to remove snow is the early morning.

At this time the snow is usually dry and has not been

exposed to the direct sun and warming tem per a tures.

• Slightly overlap each successive path to ensure all

snow will be removed.

• Throw snow downwind whenever possible.

• For extremely heavy snow, re duce the width of snow

removal by over lap ping previous path and moving

slowly.

• Keep engine clean and clear of snow during use. This

will help air flow and extend engine life.

• After snow-throwing is completed, allow engine to run

for a few minutes to melt snow and ice off the engine.

• Clean the entire snow thrower thoroughly after each

use and wipe dry so it is ready for next use.

• Spraying off unit with a hose is NOT recommended.

12

Maintenance

NOTE: Determine the left and right sides of the machine from the normal operating position.

Check for Loose Fasteners

Clean / Inspect Snow Thrower

Clean / Replace V-Belts

Check / Replace Auger Blades and Scraper Bar

Lubrication Chart

Check Engine Oil Level

Change Engine Oil

Inspect Muffler

Check / Replace Spark Plug

Empty Fuel Tank

13

Adjusting the Control Cable

Checking the Control Cable

Release the control bar to remove the slack in the control

cable (Figure 20).

IMPORTANT: The control cable must contain some slack

when you disengage the control bar for the auger blades

to stop properly.

NOTE: You may need to adjust the control cable from

position 1 (default) to position 2 if you notice belt slip

when the control bar is engaged.

NOTE: If the control cable is adjusted to position 2,

ensure that the auger stops properly when the control bar

is released

Figure 22

1. Auger blades 2. Scraper bar

1

2

Adjusting the Control Cable

1. With the control bar disengaged, unhook and move

the control cable to the highest position. (Figure 21).

Figure 20

1. Control bar

1

1. Control bar

2. Adjuster link

3. Cable positions

Figure 21

1

2

3

Position 1: Default position

(Lower Hole as shown in illustration)

Position 2

Inspecting the Auger Blades/

Scraper Bar

Before each session, inspect the auger blades for wear.

When an auger blade edge or the scraper bar has worn

down have an Authorized Service Dealer replace the

auger blades and the scraper bar (Figure 22).

NOTE: Auger blades and scraper bar are wear items and

may have to be replaced after extended use.

14

Changing the Engine Oil

Run the engine a few minutes before changing the

oil to warm it. Warm oil flows better and carries more

contaminants.

4. Place an oil drain pan under the oil drain plug, remove

the oil drain plug, and tip the snowthrower backward

and drain the used oil in the oil drain pan (Figure 23).

5. After draining the used oil, return the snowthrower to

the operating position.

6. Screw in the oil fill cap/dipstick and hand tighten it

securely (1).

NOTE: Dipstick location may vary depending on engine

type.

7. Clean around the oil filler cap/dipstick (Figure 24).

8. Unscrew the oil fill cap/dipstick and remove it

(Figure 25).

9. With the snowthrower in the operating position, care-

fully pour oil into the oil fill hole until "Full" on the fill

cap/dipstick line (Figure 25).

Max fill: 18 oz. (0.5 l), type: automotive detergent oil

with an API service classification of SJ, SL, or higher.

Figure 24

1. Oil fill cap/dipstick

1

10. Screw in the oil fill cap/dipstick and hand tighten it

securely.

11. Wipe up any spilled oil.

12. Dispose of the used oil properly at a local recycling

center.

The engine oil will be hot. Avoid skin contact

with the used engine oil.

Figure 23

1. Oil drain plug

1

1. Move snowthrower to a level surface.

2. Run snowthrower until all fuel has been depleted.

3. Remove ignition key.

Figure 25

Fill if oil is

below letter

“L” on the

¿OOHUFDS

Fill if oil

is below

“Add”

on the

GLSVWLFN

15

Servicing the Spark Plug

Use a NGK BPR6ES, Champion RN9YC, or BOSCH

WR6DC spark plug or equivalent.

1. Stop the engine and wait for all moving parts to stop.

2. Rotate the discharge chute so that it faces forward.

3. Remove the discharge chute and the discharge chute

handle by removing the three carriage bolts and three

flange nuts (Figure 26).

4. Remove the six screws that secure the shroud assembly

(Figure 27).

5. Remove the oil fill cap.

6. Remove the shroud assembly (Figure 27).

7. Install the oil fill cap.

8. Disconnect the spark plug wire from the spark plug

(Figure 28).

9. Clean around the spark plug.

10. Remove the spark plug from the cylinder head.

IMPORTANT: Replace a cracked, fouled, or dirty spark

plug. Do not clean the electrodes because grit entering

the cylinder can damage the engine.

11. Set the gap on the plug to 0.030 inch (0.76 mm)

(Figure 29).

12. Install the spark plug and torque it to 20–22 ft-lb (27–30

N-m).

13. Connect the spark plug wire to the spark plug

(Figure 28).

14. Remove the oil fill cap.

15. Install the shroud with the screws removed in step 4

(Figure 27).

NOTE: Ensure that the shroud assembly fits together in

the side grooves.

16. Install the oil fill cap.

17. Install the discharge chute, and the discharge chute

handle onto the snowthrower using the hardware re-

moved in step 3 (Figure 26).

1. Spark plug wire

Figure 28

1

Figure 29

0.030 inch

(0.76 mm)

1. Screw 3. Oil fill cap

2. Shroud assembly

Figure 27

1

2

3

Figure 26

2

3

1

1. Discharge chute 2. Carriage bolts

3. Flange nuts

16

Replacing the Drive Belt

If drive belt becomes worn, oil-soaked, excessively

cracked, frayed, or otherwise damaged, replace the belt.

1. Remove the drive side cover by removing the six screws

as shown in (Figure 30).

2. Press down on front of idler arm to release the belt

tension (Figure 30).

3. Remove the drive belt from the drive pulley (Figure 30).

4. Install the new drive belt, routing it as shown in

(Figure 31).

NOTE: Route the new drive belt first around the engine

pulley, then the idler pulley, and finally around the drive

pulley while pressing down on the front of the idler arm.

(Figure 31).

5. Install the drive side cover with the screws removed in

step 1.

NOTE: Ensure that the drive belt is properly adjusted

and operating; refer to Checking the Control Cable and

Adjusting the Control Cable in the Maintenance section

of this manual.

1. Drive side cover

2. Screw

3. Drive pulley

4. Idler arm

Figure 30

1

2

7

4

6

5

3

5. Idler pulley

6. Engine pulley

7. Drive belt

2

1. Idler arm

2. Idler pulley

3. Engine pulley

4. Drive pulley

Figure 31

1

3

2

4

17

Storage

Storing the Snowthrower

Immediately prepare your snow thrower for storage at

the end of the season or if the unit will not be used for 30

days or more.

WARNING: Never store the snow thrower with

gaso line in the tank in side a build ing where fumes

may reach an open flame, spark or pilot light as

on a fur nace, water heater, clothes dryer or gas

ap pli ance. Allow the engine to cool be fore storing

in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time,

clean it thor oughly, re move all dirt, grease, leaves, etc.

Store in a clean, dry area.

1. Clean entire snow thrower after each use.

2. Inspect and replace belts, if necessary (See “Replace-

ing the Drive Belt” sec tion of this manual).

3. Be sure that all nuts, bolts, screws, and pins are securely

fas tened. Inspect moving parts for damage, breakage

and wear. Replace if nec es sary.

FUEL SYS TEM

IMPORTANT: It is important to prevent gum deposits from

forming in essential fuel system parts such as carburetor,

fuel hose, or tank during storage. Also, alcohol blended

fuels can attract moisture which leads to separation and

formation of acids during storage. Acidic gas can damage

the fuel system of an engine while in storage.

• Empty the fuel tank by starting the engine and letting

it run until the fuel lines and car bu re tor are empty.

• Never use engine or carburetor cleaner prod ucts in

the fuel tank or permanent damage may occur.

• Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min i-

miz ing the formation of fuel gum deposits during stor age.

Add stabilizer to gasoline in fuel tank or storage container.

Always follow the mix ratio found on stabilizer container.

Run engine at least 10 min utes after adding stabilizer to

allow the stabilizer to reach the carburetor. Do not empty

the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine

oil. (See “Changing the Engine Oil” section of this man ual).

CYLINDER

1. Remove spark plug.

2. Pour one ounce (29 ml) of oil through spark plug hole

into cylinder.

3. Pull recoil starter handle slowly a few times to dis trib ute

oil.

OTHER

• Remove safety ignition key; store it in a safe place.

• Do not store gasoline from one season to another.

• Replace your gasoline can if your can starts to rust.

Rust and/or dirt in your gasoline will cause problems.

• If possible, store your snow thrower indoors and cover

it to protect it from dust and dirt.

• Cover your snow thrower with a suitable pro tec tive

cover that does not retain moisture. Do not use plastic.

Plastic cannot breathe, which allows con den sa tion to

form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/

exhaust area is still warm.

18

Troubleshooting

See appropriate section in manual unless directed to an authorized service center/department.

PROBLEM CAUSE CORRECTION

Does not start 1. Safety ignition key is not inserted. 1. Insert safety ignition key.

2. Out of fuel. 2. Fill fuel tank with fresh, clean gasoline.

3. ON/OFF switch is OFF. 3. Move ON/OFF switch to ON position.

4. Choke in OFF position. 4. Move to FULL position.

5. Primer not depressed. 5. Prime as instructed in the Operation section of this manual.

6. Engine is flooded. 6. Wait a few minutes before restarting, DO NOT prime.

7. Spark plug wire is disconnected. 7. Connect wire to spark plug.

8. Bad spark plug. 8. Replace spark plug.

9. Stale fuel. 9. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

10. Water in fuel. 10. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

11. Vapor locked fuel line. 11. Ensure all the fuel line is below the outlet of the fuel tank. Fuel

line should run continuously down from fuel tank to carburetor.

Loss of power 1. Spark plug wire loose. 1. Reconnect spark plug wire.

2. Throwing too much snow. 2. Reduce speed and width of swath.

3. Fuel tank cap is covered with ice or

snow.

3. Remove ice and snow on and around fuel tank cap.

4. Dirty or clogged muffler. 4. Clean or replace muffler.

5. Improper cable length. 5. Adjust cable.

6. Blocked muffler. 6. Clear blockage (ensure engine is cool).

7. Blocked carburetor air intake. 7. Clear blockage (ensure engine is cool).

Engine idles or

runs roughly

1. Choke is in FULL position. 1. Move choke to OFF position.

2. Blockage in fuel line. 2. Clean fuel line.

3. Stale fuel. 3. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

4. Water in fuel. 4. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

5. Carburetor is in need of replacing 5. Contact an authorized service center/department.

6. Belt stretch.

6. Replace auger v-belt.

Excessive

vibration / Handle

movement

1. Loose parts or damaged augers or

impeller.

1. Tighten all fasteners. Replace damaged parts. If vibration

remains, contact an authorized service center/department.

2. Handles not positioned correctly. 2. Ensure handles are locked into positioning.

3. Adjustment lever nuts are loose. 3. Tighten nuts until handle feels secure.

Recoil starter is

hard to pull

1. Frozen recoil starter. 1. See “IF RECOIL STARTER HAS FROZEN” in the Operation

section of this manual.

2. Rope is interfering with components. 2. Recoil rope should not be touching any wires or hoses.

Loss of snow

discharge or

slowing of snow

discharge

1. Worn belt. 1. Adjust drive cable per maintenance procedures.

2. Auger v-belt is off of pulley. 2. Check / reinstall auger v-belt.

3. Auger v-belt is worn. 3. Check / replace auger v-belt.

4. Clogged discharge chute. 4. Clean snow chute.

5. Augers / impeller jammed. 5. Remove debris or foreign object from augers / impeller.

Lights not On

(If Equipped)

1. Motor not running. 1. Start engine.

2. Loose wire connection. 2. Check wire connections at engine and both lights.

3. LED burnt out. 3. Replace LED light module. (Individual LEDs are not replaceable)

Rotator hard to

move

1. Debris in chute rotator mechanism. 1. Clean internal parts of chute rotator mechanism.

2. Cable are kinked or damaged. 2. Ensure cables are not kinked. Replace damaged cables.

19

SERVICE NOTES

20

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR100 (96182001503)

AUGER ASSEMBLY

KEY PART

NO. NO. DESCRIPTION

1212

11

3

4

1

7

2

5

6

7

8

9

10

06.03.001-F

1 532 44 27-59 BLADE

2 580 85 55-01 BEARING SUPPORT

3 532 43 76-22 BALL BEARING

4 812 00 00-28 RETAINING RING

5 817 06 04-08 SCREW 1/4-20 X 3/8

6 532 43 76-17 AUGER WELDMENT

7 580 85 54-01 CENTER BLADE PLATE

8 532 43 76-20 ROLL PIN

9 532 19 96-87 SCREW HEX WS HD 1/4-20 X 1.5

10 872 11 04-07 BOLT CARRIAGE 1/4-20 X 7/8

11 532 19 17-30 LOCKNUT 1/4-20 HEX FLANGE SIDE

12 532 13 20-04 NUT HEX 1/4-20 SERR

La page charge ...

Poulan Pro PR100 Le manuel du propriétaire

Poulan Pro PR100 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents