Mounting Dream MD2165-LK Manuel utilisateur
- Catégorie
- Supports muraux à panneau plat
- Taper
- Manuel utilisateur
Please read this instruction carefully before installation
.
Weight capacity: 60 kg (132 lbs)
.
MODEL
：
MD2165-LK
INSTALLATION INSTRUCTION
Fits for most 42-70 inches Plasma, LCD and LED TVs
.
Max VESA: 600 X 400 mm/24X16"
Thank you for purchase!We strive to provide products and services of exceptional quality.
We sincerely invite you to write a review with a good rating. For parts missed or installation problems,
please contact us at telephone (626) 604-9048 (USA) Mon - Fri 10am - 6pm (Pacific time) or email
us by customerservice@mountingdream.com , so that we may solve the issue for you.
(A6)
WARNING!
安全警告
:
欢迎您选用空中视界电视挂架。为确保安全的使用
MD2165-LK
型号产品，预防自身及
其它人员遭遇危险并防止财产受损，在使用前请仔细阅读此手册，如果您不理解这些说明或对
安装的安全性有任何疑问，请致电有资格的承包商或与空中视界客户服务部联系。组装前请仔
细检查以确保零件无缺少或缺陷，我们的客户服务代表会迅速为您的安装问题提供协助，以解
决零件的缺少或缺陷问题。通过授权经销商所购产品的替换零件将直接送货上门。切勿使用有
缺陷的零件，安装不正确可能会导致产品损坏或者身体严重受伤。切勿将本产品用于空中视界
未明示的任何其它目的，公司对于安装不正确、装配不正确或使用不当造成的产品损坏和身体
受伤不承担任何责任。
警告!
ADVERTENCIA!
AVERTISSEMENT!
Safety Warning:
Thank you for choosing Mounting Dream TV mount. For safe application of model
MD2165-LK, and preventing yourself or others from danger or property loss, please read through this
manual before use. If you do not understand these instructions or have any doubt over safety of
installation, please contact qualified contractor or Mounting Dream customer service. Please check
carefully before assembly to ensure no parts missed or damaged. Our customer service representative
will assist you timely in installation to solve the issue of parts shortage or damage. Replacement parts
purchased through authorized distributor will be delivered to your door. Please do not use defective
parts. Incorrect installation may result in product damage or body injury. Do not apply this product to
any purpose not indicated by Mounting Dream. We shall bear no responsibility for any damage or
injury resulted from incorrect installation, incorrect assembly or misuse.
Avertissement de sécurité: bienvenue à choisir le support suspendu de téléviseur de la Vue Aérienne, pour
garantir un usage sécurité du produit MD2165-LK, préserver le risque contre vous-même et des tiers et éviter
ledommage des biens, veuillez lire soigneusement ce manuel avant l'usage. Si vous ne pouvez pas
comprendre cette notice ou en cas de doute sur la sécurité de montage, veuillez téléphoner à un entrepreneur
qualifié ouau service client de la Vue Aérienne, avant l'assemblage, veuillez contrôler soigneusement pour
éviter les pièces manquantes ou défectueuses, notre représentant de service client va vous fournir une
assistance de montage, pour régler les problèmes des pièces manquantes ou défectueuses. Si vous avez
commandez le produit après d'un concessionnaire agréé, donc, nous allons livrer directement les pièces de
remplacement chez vous,il est interdit d'utiliser les pièces défectueuses, le montage incorrect peut causer le
dommage ou la blessure grave. Il est interdit d'utiliser ce produit pour un autre objectif non agréé par la Vue
Aérienne, notre société n'assume aucune responsabilité pour le dommage ou la blessure imputable au montage
incorrect, à l'assemblage incorrect ou à l'usage inadéquat.
Advertencia de seguridad: Gracias por su opción del producto de soportes para televisión de la marca
Kongzhongshijie, para garantizar el uso en seguro del modelo MD2165-LK, evitar al usuario y otras personas
sufriendo riesgo de peligrosidad y daños a la propiedad, antes de usar , por favor, lea bien este manual. Si
usted no entiende estas instrucciones o existe dudas sobre la seguridad de la instalación, por favor llame a un
contratista calificado o Centro de servicio al cliente, Antes de asemblar, verifique cuidadosamente para
asegurarse de que no encuentre la falta de piezas o piezas defectuosos , nuestros representantes deservicio al
cliente le ayudará con rapidez para los problemas de instalación ,para resolver los problemas de la falta y daño
de las piezas. En el caso de que los productos se vendan a través de distribuidores autorizados, las piezas de
repuestos serán entregados directamente a su domicilio , no utilice piezas defectuosas , la instalación
inadecuada puede causar daños o lesiones graves. No utilizar este producto para cualquier otro propósito que
fuera de sus instrucciones, la compañía no es la responsable de los daños o las pérdidas de la mala instalación
, la asamblea incorrecta o uso incorrecto.
US
FR
ES
CN
Before getting started, let's make sure this mount is
perfect for you!
1
Is your TV VESA equal to/greater than 200x100mm and equal
to/less than 600x400mm?
2
Does your TV (including accessories) weigh more than
132 lbs (60kg)?
132 lbs
(60kg)
NO --- Perfect!
Yes --- This mount is NOT compatible.
3
What is your wall made of?
CAUTION:
DO NOT install
into drywall alone
Perfect!
Drywall with
wood studs?
Solid concrete wall?
Perfect!
Yes --- Perfect!
No --- This mount is NOT compatible.
If this mount is NOT compatible, please contact
customerservice@mountingdream.com to find a compatible mount.
MAX:600mm
MAX:400mm
16"/24"
Installation tools:
-Wall plate(Left)
1 pc
1
Part list
：
Band tape
2m
Bubble level
Pencil
Screwdriver
Hammer
Electrodrill
2M
Band tape
2m
Pencil
Hammer
Electrodrill
2M
3/8"
7/32"
Stud finder
-Wall plate(Right)
1 pc
-Left bracket
1 pc
-Right bracket
1 pc
Velcro cable tie
2pcs
HDMI cable
1pc
Gifts
：
Bubble level
1pc
Socket wrench
(1/2")13mm
For parts shortage or damage, please contact us directly by
customerservice@mountingdream.com.
New delivery
will be timely
arrange
d
to replace missed or defective parts.
Attention:
Hardware for TV installation
：
g--M6X35 bolt
4 pcs
f--M5X30 bolt
4 pcs
e--M4X30 bolt
4 pcs
h--M8X50 bolt
4 pcs
c--M6X12 bolt
4 pcs
b--M5X12 bolt
4 pcs
a--M4X12 bolt
4 pcs
d--M8X25 bolt
4 pcs
Installation hardware
：
2
Installation instruction
：
Step 1
Line up wall plate and ,then attach the right wall plate
to the left wall plate by using bolts with screwdriver.
-Lag bolt
4 pcs
--M8 Washer
4 pcs
--M5X8 Bolt
4 pcs
Concrete Wall Anchor
4 pcs
CAUTION:
Do not use in drywall or wood
For concrete wall installations ONLY
k--M5/M4
washer 4pcs
i--M5/M6
spacer 4pcs
l--M6 washer
4pcs
j--M8 spacer
4pcs
m--10mm
spacer 4pcs
n--2.5mm
spacer 8pcs
16"
Place wall plate along the centerlines and use
pencil to mark 4 hole locations on the wall.
Use 7/32" diameter drill bit to drill 4 pilot holes at
marked positions to a depth of 2.5".
Put 4 lag bolts through the washers into the drilled holes, and tighten
each bolt by using a socket wrench to mount the wall plate securely.
drywall with
wood stud
The wall plate fits for 16", 24" wood stud spacing, please choose corresponding holes in the wall plate for installation.
Step 2 Wall plate installation
:
Option 1 Wall plate installation in wood stud
To avoid potential body injury or property damage:
1. Wall mount must be installed into wood stud's center, not drywall alone.
2. Drywall covering the wood stud must not exceed 16 mm (5/8 in.).
3. Minimum wood stud size: common 2 x 4 in(51 x 102 mm). Nominal 1 1/2 x 3 1/2 in(38 x 89mm)
4. The wall must be capable of supporting five times the weight of TV plus mount.
5. Make sure the logo on wall plate is upward as picture shows.
6. All lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate.
Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
Failure to follow this instruction will possibly lead to TV falling off from wall, and would possibly
cause body injuries or property loss.
3
⑤
④③
CAUTION
<16 mm(5/8 in.)
Locate the stud
with stud finder. Make
marks at the edges
of stud.
Mark centerlines
of stud.
②①
Make sure the logo on wall plate is upward
Put 4 Concrete Wall Anchors into drilled holes, and tap each
anchor flush with the wall by using a hammer. Then put 4 lag
bolts through the washers into the anchors, and tighten
each bolt by using a socket wrench to mount the wall plate
securely.
Use 3/8" diameter drill bit to drill 4 holes
at marked positions to a depth of 2.5".
3/8"
To avoid potential personal injury or property damage:
1. Make sure the logo on the wall plate is upward as the picture shows.
2. Solid concrete wall's thickness should be more than 100mm/4", and the wall must be
capable of supporting five times the weight of the TV plus the mount.
3. All anchors/lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate.
Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
Concrete wall
Option 2 Wall plate installation on concrete wall
4
UP
①
②
③
CAUTION
Make sure the logo on wall plate is upward
Use wall plate as a template and pencil to mark 4
hole locations on your desired height of the wall.
1
Select TV hardware (diameter / length / combination)
Bolt diameter: hand thread bolts into threaded inserts on the back of
TV to determine correct bolt diameter (M4, M5, M6, M8).
Too Short
Bolt length: verify adequate thread engagement with bolts or
bolts/spacers combination.We recommend thread engagement
by at least 5 turns.
- Too short will not hold the TV.
- Too long will damage the TV.
Too Long
Correct
2
Add distance to wall Irregular back Inset holes
Cables
Bolt and spacer combination: spacers sometimes are needed to
combine with bolts for several situations.
+
(For detail bolts and spacers combination, please refer to Page 7)
3
TV back
TV back
TV back
TV back
Carefully lay your TV on a non-abrasive surface, or lay it with a padding underneath
it so as not to damage the screen.
Step 3
5
Step 4
Attach brackets to the back of the TV:
①
For the TV with flat back, mount the wall plate with bolt/washer/spacer
combination.
Tips:
Make sure the ends of TV
brackets with round
holes are facing upward.
Round hole is for upper
VESA hole, and long slot
hole for lower VESA hole.
Please try best to locate
brackets symmetrically (top
& bottom) at the back of TV
to avoid brackets stick out.
Attention: Screw in bolts a
bit, then pull upward
brackets to reduce the gap
between bolts and bolt
holes to make two brackets
parallel. Then fasten bolts.
Carefully lay TV on a non-abrasive surface, or with a padding underneath it so as not to
damage the screen.
6
Bolt/spacer/washer combination options
(only for reference)
Tips:You have to remove the inner
circle of 2.5mm washer (n) in order
to fit the M8 (d) bolt.
Tips:
Make sure the ends of TV
brackets with round
holes are facing upward.
Round hole is for upper
VESA hole, and long slot
hole for lower VESA hole.
Please try best to locate
brackets symmetrically (top
& bottom) at the back of TV
to avoid brackets stick out.
Attention: Screw in bolts a
bit, then pull upward
brackets to reduce the gap
between bolts and bolt
holes to make two brackets
parallel. Then fasten bolts.
Carefully lay TV on a non-abrasive surface, or with a padding underneath it so as not to
damage the screen.
②
For TV with irregular back, mount the wall plate with bolt/washer/
spacer combination.
(Spacers are highly recommended to be added, thus enlarge
the space between TV and brackets for better functionality.)
7
Bolt/spacer/washer combination options
(only for reference)
f
k
options
spacer
j
m
h
options
spacer
j
n
n
Tips: You have to remove the inner circle of 2.5mm washer (n) in order to fit the M6 (g)
or M8 (h) bolt.
Two people are recommended
to hold and position the TV .
Attention: Cables are
highly recommended to
plug in before hanging
the TV on the wall plate.
Step 5
Hang the TV on the wall plate:
Hang the top hooks of the brackets over the top bar of the
assembled wall mount. Make sure the hooks securely hang
in the bar (figure 1).
Then attach the lower ends of the brackets to the lower bar of the
wall mount. Pull down and release
straps to lock the brackets in
the bar (figure 2).
figure 1
figure 2
8
Step 6
Adjust the tilting angle with spring loaded handle:
Hold the TV and adjust it to your desired position, and fasten
the handle firmly.
To fasten the handle:
Step A
Turn handle
clockwise
until stopped
by mount.
Turn handle
clockwise to
further fasten
the mount.
Repeat these
steps until
TV firmly
tightened.
Pull
Push
Pull out the
handle.
While holding
handle away
from mount,
turn it
counterclockwise.
Push and
release
the handle.
D
Step B Step C Step D Step E
figure 3
+0°
-20°
Handle
+0°
-20°
Adjust the swivel angle:
Grab TV and slide it to your desired direction.
Tips:Keep handle parallel with wall. Handle not
parallel with wall may be broke by hitting the wall
while TV being pushed back to the wall
9
Product dimensions:
If you have any questions about the installation,please feel free to contact us at telephone (626) 604-9048 (USA)
Mon - Fri 10am - 6pm (Pacific time) or email us by customerservice@mountingdream.com .
For more information,please visit our website:www.mountingdream.com
MAX:600mm
650mm
400mm
+0/-20°
430mm
40mm
222mm
10
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
Mounting Dream MD2165-LK Manuel utilisateur
- Catégorie
- Supports muraux à panneau plat
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Mounting Dream MD2165-LK User manual
Documents connexes
-
Mounting Dream MD5231 Manuel utilisateur
-
Mounting Dream MD2295 Manuel utilisateur
-
-
-
-
-
-
-
-