Mounting Dream MD2393-MX Manuel utilisateur
- Taper
- Manuel utilisateur
Please read this instruction carefully before installation
.
Fits for most 26-55 inches Plasma, LCD and LED TVs
.
Weight capacity: 35.5 kg (78 LBS)
.
MODEL
：
MD2393-MX
Installation option 1
(without extended arms):
Installation option 2
(with extended arms):
INSTALLATION INSTRUCTION
VESA:
300X300 mm
/11.81X11.81"
400x400 mm
/16X16"
Configuration 1
VESA:
400X200 mm
/16X7.87"
Configuration 2
VESA:
100X100 mm/4X4"
200X100 mm/7.87X4"
200X200 mm/7.87X7.87"
Thank you for purchase! We strive to provide products and services of exceptional quality.
We sincerely invite you to write an unbiased review. For parts missed or installation problems,
please contact us at telephone (626) 604-9048 (USA) Mon - Fri 10am - 6pm (Pacific time) or email
us by customerservice@mountingdream.com, so that we may solve the issue for you.
(A8)
US
WARNING!
安全警告
:
欢迎您选用空中视界电视挂架。为确保安全的使用
MD2393-MX
型号产品，预防自身及
其它人员遭遇危险并防止财产受损，在使用前请仔细阅读此手册，如果您不理解这些说明或对
安装的安全性有任何疑问，请致电有资格的承包商或与空中视界客户服务部联系。组装前请仔
细检查以确保零件无缺少或缺陷，我们的客户服务代表会迅速为您的安装问题提供协助，以解
决零件的缺少或缺陷问题。通过授权经销商所购产品的替换零件将直接送货上门。切勿使用有
缺陷的零件，安装不正确可能会导致产品损坏或者身体严重受伤。切勿将本产品用于空中视界
未明示的任何其它目的，公司对于安装不正确、装配不正确或使用不当造成的产品损坏和身体
受伤不承担任何责任。
CN
警告!
ADVERTENCIA!
AVERTISSEMENT!
Safety Warning:
Thank you for choosing Mounting Dream TV mount. For safe application of model
MD2393-MX, and preventing yourself or others from danger or property loss, please read through this
manual before use. If you do not understand these instructions or have any doubt over safety of
installation, please contact qualified contractor or Mounting Dream customer service. Please check
carefully before assembly to ensure no parts missed or damaged. Our customer service representative
will assist you timely in installation to solve the issue of parts shortage or damage. Replacement parts
purchased through authorized distributor will be delivered to your door. Please do not use defective
parts. Incorrect installation may result in product damage or body injury. Do not apply this product to
any purpose not indicated by Mounting Dream. We shall bear no responsibility for any damage or
injury resulted from incorrect installation, incorrect assembly or misuse.
Avertissement de sécurité: bienvenue à choisir le support suspendu de téléviseur de la Vue Aérienne, pour
garantir un usage sécurité du produit MD2393-MX, préserver le risque contre vous-même et des tiers et éviter
ledommage des biens, veuillez lire soigneusement ce manuel avant l'usage. Si vous ne pouvez pas
comprendre cette notice ou en cas de doute sur la sécurité de montage, veuillez téléphoner à un entrepreneur
qualifié ouau service client de la Vue Aérienne, avant l'assemblage, veuillez contrôler soigneusement pour
éviter les pièces manquantes ou défectueuses, notre représentant de service client va vous fournir une
assistance de montage, pour régler les problèmes des pièces manquantes ou défectueuses. Si vous avez
commandez le produit après d'un concessionnaire agréé, donc, nous allons livrer directement les pièces de
remplacement chez vous,il est interdit d'utiliser les pièces défectueuses, le montage incorrect peut causer le
dommage ou la blessure grave. Il est interdit d'utiliser ce produit pour un autre objectif non agréé par la Vue
Aérienne, notre société n'assume aucune responsabilité pour le dommage ou la blessure imputable au montage
incorrect, à l'assemblage incorrect ou à l'usage inadéquat.
Advertencia de seguridad: Gracias por su opción del producto de soportes para televisión de la marca
Kongzhongshijie, para garantizar el uso en seguro del modelo MD2393-MX, evitar al usuario y otras personas
sufriendo riesgo de peligrosidad y daños a la propiedad, antes de usar , por favor, lea bien este manual. Si
usted no entiende estas instrucciones o existe dudas sobre la seguridad de la instalación, por favor llame a un
contratista calificado o Centro de servicio al cliente, Antes de asemblar, verifique cuidadosamente para
asegurarse de que no encuentre la falta de piezas o piezas defectuosos , nuestros representantes deservicio al
cliente le ayudará con rapidez para los problemas de instalación ,para resolver los problemas de la falta y daño
de las piezas. En el caso de que los productos se vendan a través de distribuidores autorizados, las piezas de
repuestos serán entregados directamente a su domicilio , no utilice piezas defectuosas , la instalación
inadecuada puede causar daños o lesiones graves. No utilizar este producto para cualquier otro propósito que
fuera de sus instrucciones, la compañía no es la responsable de los daños o las pérdidas de la mala instalación
, la asamblea incorrecta o uso incorrecto.
FR
ES
Before getting started, let's make sure this mount is
perfect for you!
2
Does your TV (including accessories) weigh more than
78 lbs (35.5kg)?
78 lbs
(35.5kg)
NO --- Perfect!
Yes --- This mount is NOT compatible.
3
What is your wall made of?
CAUTION:
DO NOT install
into drywall alone
Perfect!
Drywall with
wood studs?
Solid concrete wall?
Perfect!
1
Is your TV VESA 100x100mm/4x4in, 200x100mm/7.87x4in,
200x200mm/7.87x7.87in, 300x300mm/11.81x11.81in,
400x200mm/16x7.87in or 400x400mm/16x16in?
Yes --- Perfect!
No --- This mount is NOT compatible.
MAX:400mm/16"
MAX:
400mm/16"
If this mount is NOT compatible, please contact
customerservice@mountingdream.com to find a compatible mount.
Installation tools:
Band tape
2m
Pencil
Screwdriver
Hammer
Electrodrill
2M
Band tape
2m
Pencil
Hammer
Electrodrill
2M
1
Stud finder
Bubble level
Velcro cable tie
3pcs
For parts shortage or damage, please contact us directly by
customerservice@mountingdream.com.
New delivery
will be timely
arranged to replace missed or defective parts.
Attention:
Socket wrench
1/2"(13mm)
Gifts
：
Part list
：
3/8"
Masonry Drill Bit
7/32"
Wood Drill Bit
-Extended arm
2pcs
-Wall plate unit
1pc
-Extended arm
2pcs
Wall mounting and TV bracket assembly hardware:
--Lag bolt
3pcs
--M8
Washer 3pcs
--4mm Allen key
1pc
--M6X8
Bolt 8pcs
--M6X12 Bolt
2pcs(pre-assembled)
Step 1
Remove the bolts with Allen key to separate
wall plate unit into two pieces.
Wall plate unit
Wall plate
TV plate
Installation instruction
：
2
g--M6X35 bolt
4pcs
f--M5X30 bolt
4pcs
e--M4X30 bolt
4pcs
h--M8X50 bolt
4pcs
TV mounting hardware:
c--M6X12 bolt
4pcs
b--M5X12 bolt
4pcs
a--M4X12 bolt
4pcs
d--M8X25 bolt
4pcs
k--M5/M4
washer 4pcs
i--M5/M6 spacer
4pcs
l--M6 washer
4pcs
j--M8 spacer
4pcs
m--10mm spacer
4pcs
n--2.5mm spacer
8pcs
Contact us at telephone (626) 604-9048 (USA) Mon - Fri 10am - 6pm (Pacific
additional pieces shipped directly to you.
Concrete Wall Anchor
3pcs
Concrete wall anchor (NOT INCLUDED)
drywall with
wood stud
The wall plate fits for single wood stud installation.
Step 2 Wall plate installation
:
Option 1 Wall plate installation in wood stud
To avoid potential body injury or property damage:
1. Wall mount must be installed into wood stud's center, not drywall alone.
2. Drywall covering the wood stud must not exceed 16 mm (5/8 in.).
3. Minimum wood stud size: common 2 x 4 in(51 x 102 mm). Nominal 1 1/2 x 3 1/2 in(38 x 89mm)
4. The wall must be capable of supporting five times the weight of TV plus mount.
5. Make sure the BOLT HEAD on the wall plate is upward as the picture shows.
6. All lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate.
Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
Failure to follow this instruction will possibly lead to TV falling off from wall, and would possibly
cause body injuries or property loss.
⑤
④③
CAUTION
<16 mm(5/8 in.)
Locate the stud
with stud finder. Make
marks at the edges
of stud.
Mark centerlines
of stud.
②①
Make sure the BOLT HEAD on the wall plate is upward
3
7/32"
Put 3 lag bolts through the washers into
the drilled holes, and tighten each bolt by using a
socket wrench to mount the wall plate securely.
Before totally tightening the lag bolt please check
whether the wall plate is level.
To avoid potential personal injury or property damage:
1. Make sure the BOLT HEAD on the wall plate is upward as the picture shows.
2. Solid concrete wall's thickness should be more than 100mm/4", and the wall must be
capable of supporting five times the weight of the TV plus the mount.
3. All anchors/lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate.
Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
Option 2 Wall plate installation on concrete wall
①
②
③
CAUTION
Make sure the BOLT HEAD on the wall plate is upward
4
Level the wall plate and use wall plate as a
template and pencil to mark 3 hole locations
on your desired height of the wall.
3/8"
Use 3/8" diameter drill bit to drill 3 holes
at marked positions to a depth of 2.5".
Concrete wall
Put 3 Concrete Wall Anchors (not included in the package)
into drilled holes, and tap each anchor flush with the wall
by using a hammer. Then put 3 lag bolts through the
washers into the anchors, and tighten each bolt by
using a socket wrench to mount the wall plate securely.
Before totally tightening the lag bolt please check whether
the wall plate is level.
1
Select TV hardware (diameter / length / combination)
Bolt diameter: hand thread bolts into threaded inserts on the back of
TV to determine correct bolt diameter (M4, M5, M6, M8).
Too Short
Bolt length: verify adequate thread engagement with bolts or
bolts/spacers combination. We recommend thread engagement
by at least 5 turns.
- Too short will not hold the TV.
- Too long will damage the TV.
Too Long
Correct
2
Add distance to wall Irregular back Inset holes
Cables
Bolt and spacer combination: spacers sometimes are needed to
combine with bolts for several situations.
+
(For detail bolts and spacers combination, please refer to Page 7 / 10)
3
TV back
TV back
TV back
TV back
Carefully lay your TV on a non-abrasive surface, or lay it with a padding underneath
it so as not to damage the screen.
Step 3
5
Step 4
Attach TV plate to the back of TV
Installation option 1:
If the VESA dimension is 100 mm x 100 mm(4 in x 4 in),
200 mm x 100 mm(7.87 in x 4 in) or 200 mm x 200 mm
(7.87 in x 7.87 in), take the following image as reference.
200mm
100mm
100mm
200mm
100mm
200mm
Attach TV plate to the back of TV directly:
①
For the TV with flat back, mount the TV plate with bolt/washer/spacer
combination.
Carefully lay your TV on a non-abrasive surface, or lay it with a padding underneath
it so as not to damage the screen.
6
Bolt/spacer/washer combination options
(only for reference)
Tips:You have to remove the inner
circle of 2.5mm washer (n) in order
to fit the M8 (d) bolt.
a
b
c
n
n
m
d
options
spacer
k
k
Carefully lay your TV on a non-abrasive surface, or lay it with a padding underneath
it so as not to damage the screen.
②
For TV with inset mounting holes, mount the TV plate with
bolt/washer/spacer combination.
(Spacers are highly recommended to be added, thus enlarge the
space between TV and brackets for better functionality.)
7
Bolt/spacer/washer combination options
(only for reference)
f
k
options
spacer
j
m
h
options
spacer
j
n
n
Tips: You have to remove the inner circle of 2.5mm washer (n) in order to fit the M6 (g)
or M8 (h) bolt.
e
n
n
n
m
n
n
g
options
spacer
options
spacer
k
Installation option 2:
If the VESA dimension is 400 mm x 200 mm(16 in x 7.87 in), attach
the extended arms ( , ) to the TV plate by screwing in bolts
with Allen key . Do not tighten the bolts at this step!
(see Configuration 1).
If the VESA dimension is 300 mm x 300 mm(11.81 in x 11.81 in) or
400 mm x 400 mm(16 in x 16 in) , attach the extended arms ( , )
to the TV plate by screwing in bolts with Allen key . Do not tighten
the bolts at this step! (see Configuration 2).
Configuration 2
R
L
400mm
400mm
300mm
300mm
L
R
Configuration 1
R
L
400mm
200mm
L
R
8
After the assembly of extended arms, attach the assembled plate to the
back of TV, then fasten the bolts tightly after align with the TV's
VESA holes. (Following steps only take Configuration 2 as example):
①
For the TV with flat back, mount the TV plate with bolt/washer/spacer
combination.
Carefully lay your TV on a non-abrasive surface, or lay itwith a padding underneath
it so as not to damage the screen.
9
Bolt/spacer/washer combination options
(only for reference)
Tips:You have to remove the inner
circle of 2.5mm washer (n) in order
to fit the M8 (d) bolt.
a
b
c
d
m
n
n
spacer
options
②
For TV with inset mounting holes, mount the TV plate with
bolt/washer/spacer combination.
(Spacers are highly recommended to be added, thus enlarge the
space between TV and brackets for better functionality.)
Carefully lay your TV on a non-abrasive surface, or lay it with a padding underneath
it so as not to damage the screen.
10
Bolt/spacer/washer combination options
(only for reference)
f
k
options
spacer
j
m
h
options
spacer
j
n
n
Tips: You have to remove the inner circle of 2.5mm washer (n) in order to fit the M6 (g)
or M8 (h) bolt.
e
g
n
n
m
spacer
options
spacer
options
Hang the pre-assembled TV unit on the wall plate.
(Below images only show the TV plate with extended
arms--Configuration 2).
Make sure the TV unit is horizontal, you can adjust the TV
plate a little bit (+/-5 degrees) to level the TV, then fasten
TV plate by bolts with Allen key .
Step 5
Step 6
±5°
±5°
Two people are recommended
to hold and position the TV .
Attention: Cables are highly
recommended to plug in
before hanging the TV on
the wall plate.
Tip: If TV still not level after adjustment, please loosen bolts a bit, hold
TV to adjust to level, then fasten bolts securely with Allen key.
11
Step 7
Adjust the tilting angle with spring loaded handle:
±
9
0
°
Bolt
Handle
Hold the TV and adjust it to your desired position, and fasten
the handle and the bolt opposite to the handle.
To fasten the handle:
Adjust the swivel angle:
Grab TV and slide it to your desired direction.
Step A
Turn handle
clockwise
until stopped
by mount.
Turn handle
clockwise to
further fasten
the mount.
Repeat these
steps until
TV firmly
tightened.
Pull
Push
Step B Step C Step D Step E
Pull out the
handle.
While holding
handle away
from mount,
turn it
counterclockwise.
Push and
release
the handle.
Tips:Keep handle parallel with wall. Handle not
parallel with wall may be broke by hitting the wall
while TV being pushed back to the wall
12
Product dimensions:
Manage TV cables orderly and tie them with velcro cable ties.
Step 8
+5°
-15°
490mm
MAX:400mm
MIN:100mm
435mm
MAX:400mm
MIN:100mm
435mm
70mm
13
If you have any questions about the installation, please feel free to contact us at telephone (626) 604-9048 (USA)
Mon - Fri 10am - 6pm (Pacific time) or email us by customerservice@mountingdream.com .
For more information, please visit our website:www.mountingdream.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Mounting Dream MD2393-MX Manuel utilisateur
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Mounting Dream MD2393-MX User manual
Documents connexes
-
Mounting Dream MD2295 Manuel utilisateur
-
Mounting Dream FBA_MD2411-MX Manuel utilisateur
-
-
-
-
-
-
-
-
