Zanussi ZFC233 Manuel utilisateur

Taper
Manuel utilisateur
CONGELATEUR
FREEZER
GEFRIERSCHRANK
FAGYASZTÓ SZEKRÉNY
ZFC 233
NOTICE D’UTILISATION
INSTRUCTION BOOKLET
BEDIENUNGSANLEITUNG
HASZNÁLATI UTASÍTÁS
2222 252-83
52
2
Lors de sa fabrication, cet appareil a été construit selon des normes, directives et/ou décrets pour une utilisation
sur le territoire français.
Pour la sécurité des biens et des personnes ainsi que pour le respect de l’environnement, vous devez
d’abord lire impérativement les préconisations suivantes avant toute utilisation de votre appareil.
Pour éviter tout risque de détérioration de l’appareil, transportez-le dans sa position d’utilisation muni de
ses cales de transport (selon modèle).
Au déballage de celui-ci, et pour empêcher des risques d’asphyxie et corporel, tenez les matériaux
d’emballage hors de la portée des enfants.
Pour éviter tout risque (mobilier, immobilier, corporel,…), l’installation, les raccordements (eau, gaz,
électricité, évacuation selon modèle), la mise en service et la maintenance de votre appareil doivent être
effectués par un professionnel qualifié.
Votre appareil a été conçu pour être utilisé par des adultes. Il est destiné à un usage domestique normal.
Ne l’utilisez pas à des fins commerciales ou industrielles ou pour d’autres buts que ceux pour lesquels il a
été conçu. Vous éviterez ainsi des risques matériel et corporel.
Débranchez votre appareil avant toute opération de nettoyage manuel. N’utilisez que des produits du
commerce non corrosifs ou non inflammables. Toute projection d’eau ou de vapeur est proscrite pour
écarter le risque d’électrocution.
Si votre appareil est équipé d’un éclairage, débranchez l’appareil avant de procéder au changement de
l’ampoule (ou du néon, etc.) pour éviter de s’électrocuter.
Afin d’empêcher des risques d’explosion et d’incendie, ne placez pas de produits inflammables ou
d’éléments imbibés de produits inflammables à l’intérieur, à proximité ou sur l’appareil.
Lors de la mise au rebut de votre appareil, et pour écarter tout risque corporel, mettez hors d’usage ce
qui pourrait présenter un danger : coupez le câble d’alimentation au ras de l’appareil. Informez-vous
auprès des services de votre commune des endroits autorisés pour la mise au rebut de l’appareil.
Respectez la chaîne de froid dès l’acquisition d’un aliment jusqu’à sa consommation pour exclure le
risque d’intoxication alimentaire.
Veuillez maintenant lire attentivement cette notice pour une utilisation optimale de votre appareil.
Printed on recycled paper
WARNINGS
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move house
and leave the appliance, always ensure that the book is supplied with the appliance in order that the
new owner can be acquainted with the functioning of the appliance and the relevant warnings.
If this appliance featuring magnetic door seals is to replace an older appliance having a spring lock
(latch) on the door or lid, be sure to make that spring lock unusable before you discard the old
appliance. This will prevent it from becoming a death-trap for a child.
These warnings are provided in the interest of safety.You must read them carefully before installing or
using the appliance.
General Safety
This appliance is designed to be operated by
adults. Children should not be allowed to tamper
with the controls or play with the product.
It is dangerous to alter the specifications or
modify this product in any way.
Before any cleaning or maintenance work is carried
out, be sure to switch off and unplug the appliance.
This appliance is heavy. Care should be taken
when moving it
Ice lollies can cause frost burns if consumed
straight from the appliance.
Take utmost care when handling your
appliance so as not to cause any damages to
the cooling unit with consequent possible
fluid leakages.
The appliance must not be located close to
radiators or gas cookers.
Avoid prolonged exposure of the appliance to
direct sunlight.
There must be adequate ventilation round the
back of the appliance and any damage to the
refrigerant circuit must be avoided.
For freezers only (except built-in models): an
ideal location is the cellar or basement.
Do not use other electrical appliances (such
as ice cream makers) inside of refrigerating
appliances.
Service/Repair
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person
This product should be serviced by an authorized
Service Centre, and only genuine spare parts
should be used.
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out
by inexperienced persons may cause injury or
more serious malfunctioning. Refer to your local
Service Centre, and always insist on genuine
spare parts.
This appliance contains hydrocarbons in its
cooling unit; maintenance and recharging must
therefore only be carried out by authorized
technicians.
Use
The domestic refrigerators and freezers are
designed to be used specifically for the storage
of edible foodstuffs only.
Best performance is obtained with ambient
temperature between +18°C and +43°C (class T);
+18°C and +38°C (class ST); +16°C and +32°C
(class N); +10°C and +32°C (class SN). The
class of your appliance is shown on its rating
plate.
Warning: when the ambient temperature is not
included within the range indicated for the class
of this appliance, the following instructions must
be observed: when the ambient temperature
drops below the minimum level, the storage
temperature in the freezer compartment cannot
be guaranteed; therefore it is advisable to use the
food stored as soon as possible.
Frozen food must not be re-frozen once it has
been thawed out.
Manufacturers’ storage recommendations should
be strictly adhered to. Refer to relevant
instructions.
The inner lining of the appliance consists of
channels through which the refrigerant passes. If
these should be punctured this would damage the
appliance beyond repair and cause food loss. DO
NOT USE SHARP INSTRUMENTS to scrape off
frost or ice. Frost may be removed by using the
scraper provided. Under no circumstances should
solid ice be forced off the liner. Solid ice should be
allowed to thaw when defrosting the appliance.
Do not place carbonated or fizzy drinks in the
freezer as it creates pressure on the container,
which may cause it to explode, resulting in
damage to the appliance.
30
Rear spacers
In the bag with the documentation, there are two
spacers which must be fitted in the two top
corners.
Slacken the screws and insert the spacer under the
screw head, then re-tighten the screws.
Changing the opening
direction of the door
Before carrying out any operations, remove the plug
from the power socket.
To change the opening direction of the door, proceed
as follows:
1. Remove the ventilation grill (D).
2. Unscrew the bottom hinge (E).
3. Remove the door by releasing it from the top
hinge pin (G).
4. Remove the pin then mount these on the
opposite side.
5. Remove the two plugs, to reveal the holes for the
hinge pivots, and remount them on the other side.
6. Replace the freezer door.
7. using a 10 mm spanner, unscrew the hinge pin
(E) and reassemble it on the opposite side of the
hinge;
8. Screw down the bottom hinge (E) on the opposite
side by using the screws previously removed.
9. Remove the plug (F) from the ventilation grill (D)
and replace it on the opposite side.
10.Re-assemble the ventilation grill (D).
11.Unscrew the handle. Refit it on the opposite side
after having pierced the plugs with a punch.
Cover the holes left open with the plugs
contained in the documentation pack.
Warning:
After having reversed the opening direction of the
doors check that all the screws are properly
tightened and that the magnetic seal adheres to the
cabinet. If the ambient temperature is cold (i.e. in
Winter), the gasket may not fit perfectly to the
cabinet. In that case, wait for the natural fitting of the
gasket or accelerate this process by heating up the
part involved with a normal hairdrier.
D594
G
F
D
PR18
F
F
F
E
E
D162/1
24
Installation
During normal operation, the condenser and
compressor at the back of the appliance heat up
considerably. For safety reasons, minimum
ventilation must be as shown in the instructions.
Attention: keep ventilation openings clear of
obstruction.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important: if the supply cord is damaged, it must
be replaced by a special cord or assembly availa-
ble from the manufacturer or its service agent.
If the appliance is transported horizontally, it is
possible that the oil contained in the compressor
flows in the refrigerant circuit. It is advisable to
wait at least two hours before connecting the
appliance to allow the oil to flow back in the
compressor.
There are working parts in this product which
heat up. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
installation instructions.
Parts which heat up should not be exposed.
Wherever possible the back of the product should
be against a wall.
Environment Protection
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials.The
appliance shall not be discarded together with
the urban refuse and rubbish. Avoid damaging
the cooling unit, especially at the rear near the
heat exchanger. Information on your local
disposal sites may be obtained from municipal
authorities.The materials used on this appliance
marked by the symbol are recyclable.
Warnings 23
Use 25
Cleaning the interior 25
Control panel 25
Operation 25
Temperature regulation 25
Fast freezing 25
Warning light 25
Freezing fresh food 26
Storage of frozen food 26
Thawing 26
Ice-cube production 26
Cold accumulators 26
Hints 27
Hints for freezing 27
Hints for storage of frozen food 27
Maintenance 28
Periodic cleaning 28
Periods of no operation 28
Defrosting 28
Customer service and spare parts 29
Installation 29
Location 29
Electrical connection 29
Rear spacers 30
Changing the opening direction of the door 30
CONTENTS
29
Before calling your local dealer for servicing
assistance, check the following points to see if
you may not resolve the problem yourself:
Make sure that the freezer is plugged into the wall
socket correctly, and that electrical current arrives
to the freezer without interruption.
Control the thermostat setting.
In the event that the freezer makes excessive
noise or vibration, make sure that it is not in direct
contact with the wall or adjacent furniture.
If defective operation continues after these
controls, call your local Service Network and
provide all the data listed on the rating plate:
model, serial number, etc.
CUSTOMER SERVICE AND SPARE PARTS
INSTALLATION
Location
The appliance should be installed well away from
sources of heat such as radiators, boilers, direct
sunlight etc.
Ensure that air can circulate freely around the back
of the cabinet. To ensure best performance, if the
appliance is positioned below an overhanging wall
unit, the minimum distance between the top of the
cabinet and the wall unit must be at least 100 mm
(A). Ideally, however, the appliance should not be
positioned below overhanging wall units (B).
Accurate levelling is ensured by one or more
adjustable feet at the base of the cabinet.
Important
It is essential that the appliance be connected to an
efficient earth tap. For this purpose the supply cable
plug incorporates a special earth contact. If the
sockets of your domestic wiring system are not
earthed, have the appliance connected to a separate
earth wire by a qualified electrician in accordance
with existing safety regulations.
The Manufacturer declines all responsibility if
the above safety precautions are not observed.
This appliance complies with EEC directive
number 87/308 of 2/6/87 relative to radio
interference suppression.
This appliance complies with the following
E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and
subsequent mod)fications;
- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Electrical connection
Before plugging in, ensure that the voltage and
frequency shown on the serial number plate
correspond to your domestic power supply. Voltage
can vary by ±6% of the rated voltage.
100 mm 10 mm
10 mm
B
NP00
ATTENTION!
It must be possible to disconnect the appliance from
the mains power supply; the plug must therefore be
easily accessible after installation.
25
Temperature regulation
The temperature is automatically regulated and can
be increased to achieve a higher temperature
(warmer) by rotating the thermostat knob towards
minimum or reduced (colder) by rotating the knob
towards maximum. However, the exact setting should
be chosen keeping in mina that the temperature
inside the refrigerator depends on:
room temperature;
how often the door is opened;
the quantity of food stored;
location of appliance.
A medium setting is generally the most suitable.
To stop operation, simply turn the thermostat knob to
position «
0
».
Fast freezing
For quick-freezing, press the N/S switch (C). The
quick-freezing indicator light (B) will then light up.
Warning light
Warning light (A) lights up when the temperature
inside the freezer compartment has increased to a
value which might endanger the long-term storage of
food in the compartment. When the appliance is
switched on for the first time or when food is placed
in the compartment for freezing, it is normal for this
light to remain on until the temperature has reached
the level required for correct storage.
Cleaning the interior
Before using the appliance for the first time, wash
the interior and all internal accessories with luke-
warm water and some neutral soap so as to remove
the typical smell of a brand-new product, then dry
thoroughly.
USE
This freezer has been marked with the symbol, which means that it is suited to the freezing of fresh
foods, the conservation of frozen foods and the production of ice-cubes.
The control panel
D
A
C
E
B
5
6
0
2
3
1
4
A. Temperature alarm light
B. Quick-freezing indicator light
C. N/S switch
D. Function indicator light
E. Thermostat knob
Operation
Insert the power supply plug into the nearest wall
socket (the function indicator light (D) will light up
indicating that the freezer is receiving electrical
input.)
Turn the thermostat knob (E) to the right to a
medium setting (the temperature alarm light (A) will
light up).
To turn off the freezer, turn the thermostat knob to
the «O» position.
Do not use detergents or abrasive
powders, as these will damage the finish.
28
MAINTENANCE
Unplug the appliance before carrying out
any maintenance operation.
Warning
This appliance contains hydrocarbons in its cooling
unit; maintenance and recharging must therefore
only be carried out by authorized technicians.
Periodic cleaning
Clean the inside with warm water and bicarbonate of
soda.
Rinse and dry thoroughly.
Do not pull, move or damage any pipes and
/or cables inside the cabinet .
Clean the condenser (black grill) and the compressor
at the back of the appliance with a brush or a
vacuum cleaner. This operation will improve the
performance of the appliance and save electricity
consumption.
Many proprietary kitchen surface cleaners
contain chemicals that can attack/damage the
plastics used in this appliance. For this reason it
is recommended that the outer casing of this
appliance is only cleaned with warm water with a
little washing-up liquid added.
Extended periods of non-operation
Whenever the freezer is not to be used for an
extended period of time, disconnect it from the wall
socket and empty and clean the freezer. Remember
to leave the door open for the entire period of time in
which the freezer is not to be used.
Defrosting
Scrape away the frost with the plastic scraper
provided with the freezer when this layer arrives to
approximately 4 mm in height. For this operation, you
do not need to unplug the freezer or remove all
frozen foods. Whenever the layer of frost exceeds 4
mm in thickness, you must proceed to a complete
defrosting. Take advantage of the periods when you
do not trave too much food in storage to do this by
proceeding as follows:
1. Empty the freezer and temporarily store the
frozen food removed in a cool place, wrapped in
several sheets of newspaper.
2. Set the thermostat to the «O» position or unplug
the freezer from the wall socket.
3. Keep the freezer door open.
4. Use the scraper together with a collecting tray
and insert it in the lower central part of the freezer
as shown in Figure.
5. The collecting tray should be positioned directly
below in order to receive the water which will exit
during defrosting. Afterwards, dry all freezer
surfaces with care.
6. Keep the scraper for future use.
7. Re-connect the plug and set the freezer to the
quickfreezing position. After two hours you may
replace the frozen foods previously removed.
Important
Never use knives or metal objects to scrape away
accumulated frost.
An increase in the surface temperature of the frozen
foods during defrosting will notable diminish the
duration of their conservation.
D068
Freezing fresh food
The 4-star compartment is suitable for long
term storage of commercially frozen food, and for
freezing fresh food.
If the freezer has already been working for some
time, press the N/S switch at least 12 hours before
introducing the food into the freezer in order to
ensure better freezing results.
Place the food to be frozen in the compartment as
shown in figure.
In order to freeze the quantity indicated on the rating
plate, arrange the food directly in contact with the
cooling surfaces. If the food is frozen in the baskets,
the maximum quantity freezable is slightly less.
Important
When electrical current happens to be cut off, the
freezer door must not be opened. If the power failure
is short (up to 6-8 hours) and the freezer is full, there
is no risk that the food will spoil. If the power failure
lasts longer, the food must be consumed as rapidly
as possible, or otherwise cooked and re-frozen
again.
Frozen food storage
When the freezer is being turned on for the first time,
or after a prolonged period of disuse, press the N/S
switch and then wait at least two hours before
introducing the food to be conserved.You may then
repress the switch. This two-hour waiting period may
be avoided if the freezer has already been in
operation.
To obtain the best performance from this appliance,
you should:
if large quantities of food are to be stored, remove all
drawers and baskets from appliance (except for the
last one at the bottom) and place food on cooling
shelves.
Pay careful attention not to exceed load limit stated
on the side of the upper section (where applicable).
Thawing out frozen foods
Frozen foods must be allowed to thaw out before use
either in the refrigerator (meat, poultry, fish, etc.) or
at room temperature (ali other foods) according to
the available time. Frozen products which come in
small-sized or separate packages may be cooked
directly without thawing; obviously, in this case, the
cooking time will fast a little longer.
Ice-cube production
Fill the trays with water to 3/4 of their height, to
permit the expansion of the ice, then put them in the
space below the quick-freezing compartment (see
the diagram). If the water in your area is rich in
minerai salts (limestone, in particular), we advise you
to use noncarbonated mineral water for the
production of ice cubes. The ice-cubes may be
shaken out of the plastic trays with a slight twist.
10 kg
10 kg
Cold accumulators
2 cold accumulators are supplied in the freezer;
these increase the length of time for which food will
keep in the event of a power failure or breakdown.
They must be placed in the top drawer.
27
Hints for freezing
All products to be frozen must be fresh and of
excellent quality.
Each freezing package must be adjusted to the
family’s consumption quantity in order to be used
just once.
Small-sized freezing packages allow a more rapid
and uniform freezing.
Do not forget that once frozen foods trave thawed
out, they spoil rapidly.
Low-fat content foods are better conserved in the
freezer than those with higher fat content. Salt
(whenever present) reduces the duration of
satisfactory conservation.
Foods to be frozen must be enclosed in air-tight
sacks or containers especially indicated for this
purpose.
Close these sacks or containers tightly to
eliminate all air.
Never piace bottles or cans of carbonated
beverages in the freezer. These might explode.
Never introduce hot foods or liquids.
Never fill the freezing sacks or containers with
covers to the brim.
Do not consume certain products (popsicles, etc.)
immediately after removing them from the
freezer,because their extremely low temperature
might cause burns.
Indicate the freezing date on every sack or
container as a means of controlling conservation
times.
Never open the freezer door or introduce new
foods to be frozen whenever a Quick-freezing
phase is already in progress.
The symbols on the drawers show different types
of frozen goods. The numbers indicate storage
times in months for the appropriate types of
frozen goods. Whether the upper or lower value of
the indicated storage time is valid depends on the
quality of the foods and pre-treating before
freezing.
HINTS
Hints for storage of frozen food
Always check the preparation date indicated on
the frozen foods you buy and respect the
expiration time provided by the producer.
Do not open the freezer door too often and leave
it open only for the minimum time necessary.
Unnecessary increases in temperature will
notably reduce the duration of the frozen food
conservation.
Make sure that all frozen food packages are
intact; otherwise the food may trave spoiled.
If such packages present signs of swelling or
humidity marks, this means that the food has not
been conserved correctly, implying that the
product has lost some of its original quality.
When buying frozen foods, carry them in a
thermally insulated shopping bag whenever
possible. In any case, always purchase frozen
foods at the end of your shopping. Wrap the
frozen foods in newspaper and then put them into
the freezer as soon as you arrive home.
Always check the frozen foods you buy carefully
at the moment of purchase, because even
partiallythawed foods must not be re-frozen but
must be consumed within 24 hours of purchase.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Zanussi ZFC233 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues