Maytag MTW5621TQ1 Le manuel du propriétaire

Marque: Maytag

Modèle: MTW5621TQ1

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

AUTOMATIC WASHER

USE & CARE GUIDE

LAVADORA AUTOMATICA

MANUAL DE USO Y CUIDADO

LAVEUSE AUTOMATIQU E

GUIDE D'UTILISATION ET D'ENTRETIEN

FOR QUESTIONS ABOUT FEATURES, OPERATION/PERFORMANCE,

PARTS, ACCESSORIES OR SERVICE CALL: 1.800.688.9900

IN CANADA, CALL: 1.800.807.6777

VISIT OUR WEBSITE AT WWW.MAYTAG.COM

IN CANADA, WWW.MAYTAG.CA

W10092682

SI TIENE PREGUNTAS RESPECTO A LAS CARACTERiSTJCA8,

FUNCIONAMIENTO, RENDIMIENTO, PARTES, ACCESORIOS O

SERVICIO TECNICO, LLAME AL: 1.800.688.9900

EN CANADa,, LLAME AL: 1.800.807.6777

VISITE NUESTR(-) SITIO WEB EN

WWW.MAYTAG.C(-)M

EN CANADA, WWW.MAYTAG.CA

AU CANADA, POUR ASSISTANCE, INSTALLATION OU SERVICE,

COMPOSER LE : 1.800.807.6777

OU VISITEZ NOTRE SITE INTERNET _,

WWW.MAYTAG.CA

TABLE OF CONTENTS

WASHER SAFETY ................................................................. 3

INSTALLATION REQUIREMENTS ........................................ 4

TOOI.S AND PARTS .......................................................... 4

EOCATION REQUIREMENTS ............................................ 5

[)RAIN SYSTEM ................................................................. B

EI.ECTRICAI. REQUIREMENTS ........................................... 6

INSTALLATION INSTRUCTIONS ........................................ 7

BEFORE YOU START ......................................................... 7

REMOVE SHIPPING MATERIAI.S ....................................... 7

CONNECT [)RAIN HOSE .................................................. 9

CONNECT THE INI.ET HOSES .......................................... 9

SECURE THE DRAIN HOSE ............................................. 10

EEVEI. THE WASHER ....................................................... 11

COMPLETE INSTAl I ATION ............................................ 12

WASHER USE ..................................................................... 13

STARTING YOUR WASHER ............................................ 13

WASHER CARE ................................................................... 15

C'LEANING YOUR WASHER ........................................... 1,5

WATER INI.ET HOSES ...................................................... 15

MOVING AND STORAGE ............................................... 15

TROUBLESHOOTING ........................................................ 16

WASHER AND COMPONENTS ...................................... 16

WASHER OPERATION .................................................... 17

WASHER RESUI;FS .......................................................... 18

ASSISTANCE OR SERVICE .................................................. 19

IN THE U.S.A ................................................................... 19

IN CANADA .................................................................... 19

WARRANTY ....................................................................... 20

INDICE

SEGURIDAD DE LA LAVADORA ...................................... 22

REQUISITOS DE INSTALACION ....................................... 23

HERRAMIENTAS Y PIEZAS .............................................. 23

REQUISITOS [DE UBICACI(')N ........................................ 24

SISTEMA DE DESAGOE ................................................... 25

REQUISITOS El ECTRICOS .............................................. 26

INSTRUCCIONES DE INSTALAClON ............................... 27

ANTES DE EMPEZAR ...................................................... 27

COMO QUITAR El. MATERIAl. [DETRANSPORTE ......... 27

COMO CONECTAR I.A MANGUERA DE DESAGUE ..... 28

CONECTE [.AS MANGUERAS DE ENTRADA ................. 29

ASEGURE I.A MANGUERA DE DESAGUE ...................... 30

NIVELE I.A I.AVADORA .................................................. 31

COMPLETE I.A INSTALACION ........................................ 32

USO DE LA LAVADORA ................................................... 33

PUESTA EN MARCHA DE SU LAVADORA .................... 33

CUIDADO DE LA LAVADORA ......................................... 35

(-_('_)MO HMPIAR SU EAVADORA ................................... 35

MANGUERAS DE ENTRADA DE AGUA ......................... 35

MUDANZA Y AEMACENAJE .......................................... 35

SOLUClON DE PROBLEMAS ............................................ 36

EAVADORA Y COMPONENTES ..................................... 36

FUNC[ONAMIENTO DE [A [.AVADORA ....................... 37

RESUI.TADOS [DE I.A I.AVADORA ................................. 38

AYUDA O SERVlClO Tf_CNICO ........................................ 39

EN I.OS EE.UU ................................................................ 39

EN CANADI_ ................................................................... 39

GARANT(A ........................................................................ 40

TABLE DES MATIERES

S[_CURITI_ DE LA LAVEUSE ................................................ 41

EXIGENCES D'INSTALLATION .......................................... 42

OUIII I.AGE ET PIECES .................................................... 42

EXIGENCES D'EMPI.ACEMENT. ...................................... 43

SYSTEME DE VIDANGE ................................................... 44

SPECI FICATIONS [_I.ECTRI(_U ES..................................... 4,5

INSTRUCTIONS D'INSTALLATION .................................. 46

AVANT DE COMMENCER .............................................. 46

RETRAIT DU MATERIEl. D'EXPEDITION ......................... 46

RACCORDEMENT DU TUYAU DE VIDANGE ................ 47

RACCORDEMENT DES TUYAUX D'ARRIVEE D'EAU ..... 48

IMMOBII.ISATION DU TUYAU [DE VIDANGE ............... 49

REG[ AGE [DEI/APLOMB [DE I.A I.AVEUSE ..................... 50

ACHEVER I.'INSTAI.I.ATION ........................................... 51

UTILISATION DE LA LAVEUSE .......................................... 52

MISE EN MARCHE DE I.A EAVEUSE ................................ 52

ENTRETIEN DE LA LAVEUSE ............................................. 54

NETTOYAGE [DE VOTRE I.AVEUSE ................................. 54

ROBINETS D'ARRIVEE D'EAU ........................................ 54

PREPARATION AVANT UN ENTREPOSAGE OU UN

DEMENAGEMENT. .......................................................... 54

D[_PANNAGE ..................................................................... 55

IA I AVEUSE ET SES (-_OMPOSANTS ............................... 55

FONCTIONNEMENT [DE I.A LAVEUSE ............................ 56

RI_SUI_TATS DE I.AVAGE ................................................. 56

ASSISTANCE OU SERVICE ................................................. 58

AUX ETATS-UNIS ............................................................ 58

AU CANADA ................................................................... 58

GARANTIE ......................................................................... 59

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer follow basic precautions,

including the following:

• Read all instructions before using the washer.

• Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

• Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

• Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been

used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

• Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used

near children.

• Before the washer is removed from service or discarded,

remove the door or lid.

• Do not reach into the washer if the drum, tub or agitator is

moving.

• Do not install or store the washer where it will be exposed to

the weather.

• Do not tamper with controls.

• Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user-repair instructions that you understand and

have the skills to carry out.

• See "Electrical Requirements" for grounding instructions.

this time.

SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

TOOLS AND PARTS

Gather the required tools and parts before starting installation. The parts supplied are in the

washer basket.

Parts needed (not provided with washer):

• Inlet hoses • Flat washers

To order:

• Call the dealer from whom you purchased your washer.

• Reference the toll-free number on the front page of the Use and Care Guide.

• Visit the website on the front page of the Use and Care Guide.

NOTE: Replace inlet hoses after _ years of use to reduce the risk of hose failure. Record hose

installation or replacement dates for future reference.

Parts supplied:

A B

A. Beaded tie strap

B. Front I_'veling f_'et with Ruts (2)

C. Drain hose form

Tools needed for installation:

• Adjustable or open end • Ruler or measuring tape

wrench %6" (14 mm)

• Pliers that open to 1%6"

• Level (3.95 cm)

• Wood block • Flashlight (optional)

Alternate Parts

Your installation may require additional parts. For information on ordering, please refer to the

toll-free phone numbers on the front page of the Use and Care Guide.

If You Have: You Will Need to Buy:

[aundry tub or standpipe Sump pump system (if not already available)

taller than 96" (2.4 m)

1" (2.5 cm) diameter 1%" (3.2 cm) diameter to 1" (2.5 cm) diameter standpipe

standpipe adapter, Part Number 280130

Overhead sewer Standard 20 gal. (76 [.) 39" (99 cm) tall drain tub or utility

sink, sump pump and connectors (available from local

plumbing suppliers)

Floor drain Siphon break kit, Part Number 280129; additional drain hose,

Part Number 3357090

Water faucets beyond 2 longer water fill hoses:

reach of fill hoses 6 ft (1.8 m) Part Number 76314,

10 ft (3.0 m) Part Number 350008

Drain hose too short Kit Part Number 2801 31

lint clogged drain [)rain protector, Part Number 367031

LOCATION REQU I REMENTS

Selecting the proper location for your washer improves performance and minimizes noise and

possible washer "walk."

Your washer can be installed in a basement, laundry room, closet, or recessed area. See

"Drain System."

IMPORTANT: Do not install or store the washer where it will be exposed to the weather.

Proper installation is your responsibility.

You will need:

• A water heater set to deliver 120°F 149°C) water to the washer.

• A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is

attached to the back of the washer. See "Electrical Requirements."

• Hot and cold water faucets located within 3 ft (90 cm) of the hot and cold water fill

valves, and water pressure of 5-100 psi/34.5-690 kPa). Washers with triple dispensers

require 20-100 psi (138-690 kPa) for best performance.

• A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the

washer on carpeting is not recommended.

• A sturdy floor to support the washer weight (washer, water and load) of 315 Ibs (143 kgs).

Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can

remain in the washer and can cause damage in low temperatures. See "Washer Care."

Recessed area or closet installation

The dimensions shown are for the recommended spacing allowed (A and B), except the closet

door ventilation openings. [he dimensions shown for the closet door ventilation openings (C)

are the minimum required.

olo

16,,5[-

(46.3cm)

[_ 24n -

(1__m_)

O"T_-_-- 27"_6" -_-11"1_-25_/_"_1 1<-4"

(Ocm) (68.6crn) (0¢rn) (2.Scrn) (64,80rn) (1O.2¢rn)

A B

__ _ 3"

(7,6crn)

NNN-

__ _ 3"

(7.6cm)

A. Frollt vi(!w

8. Side view

(7. Closet door with vents

• Additional spacing should be considered for ease of installation and servicing.

• Additional clearances may be required for wall, door and floor moldings.

• Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended to reduce

noise transfer.

• If a closet door is installed, the minimum air openings in the top and bottom of the door

are required (C). [ouvered doors with air openings in the top and bottom are acceptable.

• Companion appliance spacing should also be considered.

DRAIN SYSTEM

The washer can be installed using the standpipe drain system (floor or wall), the laundry tub

drain system, or the floor drain system. Select the drain hose installation method you need.

See '"ibols and Parts."

Standpipe drain system--wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum

carry-away capacity can be no less than 17 gal. (64 L) per minute. A 1V,¢ (3.2 cm) diameter to

1" (2.5 cm) diameter standpipe adapter kit is available. See "]bols and Parts."

The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (244 cm/

from the bottom of the washer.

lb avoidsiphoning,nomorethan8"(20.3cm)ofdrainhoseshouldbeinsidethestandpipe.

Securedrainhosewithbeadedtiestrap.

ELECTRICAL REQUIREMENTS

39"

(99 cm)

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gah (76 1.)capacity. The top of the laundry tub must be

at least 39" (99 cm) above the floor and no higher than 96" (244 cm) from the bottom of the

washer.

Floor drain system (view D)

The floor drain system requires a siphon break that may be purchased separately. See "lL_ols

and Parts."

The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer.

Additional hoses might be needed.

lo avoid siphoning, no more than 8" (20.3 cm) of drain hose should be below the top of the

wash tub. Secure drain hose with beaded tie strap.

C D

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter,

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

• A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-

delay fuse or circuit breaker is recommended. It is recommended that a separate circuit

serving only this appliance be provided.

• This washer is equipped with a power supply cord having a 3 prong grounding plug.

• lo minimize possible shock hazard, the cord must be plugged into a mating, 3 prong,

grounding-type outlet, grounded in accordance with local codes and ordinances. If a

mating outlet is not available, it is the personal responsibility and obligation of the

customer to have the properly grounded outlet installed by a qualified electrician.

• If codes permit and a separate ground wire is used, it is recommended that a qualified

electrician determine that the ground path is adequate.

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not sure the washer is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

GROUNDING iNSTRUCTiONS

For a grounded, cord-connected washer:

This washer must be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electrical

shock by providing a path of least resistance for electric

current. This washer is equipped with a cord having an

equipmenbgrounding conductor and a grounding plug. The

plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in

doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance - if it will

not fit the outlet, have a proper outlet installed by a qualified

electrician.

For a permanently connected washer:

This washer must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the appliance.

INSTALLATION INSTRUCTIONS

BEFORE YOU START

Excessive Weight Hazard

Use two or more people to move and install washer.

Failure to do so can result in back or other injury.

NOTE: lo avoid floor damage, set the washer onto cardboard before moving across floor.

REMOVE SHIPPING MATERIALS

Removing the shipping material is necessary for proper operation. If the shipping material is

not removed, the washer will make excessive noise.

1. Move the washer to within approximately 3 ft (90 cm) of its final location.

2. [he washer must be in the upright position and not tilted before removing the shipping

material.

3. Locate the yellow shipping materials on the rear of the machine, near the bottom. Follow

the steps for your particular model, either the one with the straight power cord and cord

restraint or the looped power cord version.

Straight power cord

Looped power cord

Remove power plug and yellow strap from machine base to release the rear leveling

system.

Firmly grasp the power cord and pull to completely remove the power cord, cord

restraint, and pin from the rear paneh

Confirm that the power cord restraint (A), and pin (B) are removed.

Looped power cord

Firmly grasp the yellow shipping strap and pull until both ends are completely removed

from washer.

A. Power cord restraint 8. Pin

[b remove the power cord from the cord restraint, push the power cord in, press TAB, and

then pull the power cord out.

2. Check that two (2) cotter pills were removed with the shipping strap.

CONNECT DRAIN HOSE

Proper connection of tile drain hose protects your floors from damage clue to water leakage.

Read and follow these instructions.

]he drain hose is connected to your washer and is stored inside the washer cabinet.

Remove drain hose from washer cabinet

Gently pull the corrugated drain hose out of the washer from the top of the hose. Continue to

pull the hose until the end emerges. Do not force excess drain hose back into the rear of the

washer.

Laundry tub drain or standpipe drain

Connecting the drain hose form to the corrugated drain hose

A. Drain hose reliefs

1. Feed end of drain hose into one end of form. Place end of drain hose form into the drain

hose relief.

2. Bend the hose over the top of the form and feed into the other end of the form.

To keep drain water from going back into the washer:

• Do not force excess drain hose into standpipe. Hose should be secure but loose enough

to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

Floor drain

Do not install the drain hose form on to the corrugated drain hose. You may need additional

parts. See Floor drain under "lbols and Parts."

CONNECT THE INLET HOSES

The washer must be connected to the water faucets using new inlet hoses (not provided). Do

not use old hoses.

Insert new flat washers into each end of the inlet hoses. Firmly seat the washers in the

couplings.

A B

A. Coupling

B. Washer

Connect the inlet hoses to the water faucets

Make sure tile washer basket is empty.

1. Attach hose to the hot water faucet. Screw on coupling by hand until it is seated on the

washer.

2. Attach hose to the cold water faucet. Screw on coupling by hand until it is seated on the

washer.

3. Using pliers, tighten the couplings with an additional two-thirds turn.

lighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. [Damage to the valves can

result.

Clear the water lines

• Run water through both faucets and inlet hoses, into a laundry tub, drainpipe or bucket,

to get rid of particles in the water lines that might clog the inlet valve screens.

• Check the temperature of the water to make sure that the hot water hose is connected to

the hot water faucet and that the cold water hose is connected to the cold water faucet.

Connect the inlet hoses to the washer

A. Cold water inlet valve

B. Hot water inlet valve

1. Attach the hot water hose to the bottom inlet valve.

2. Attaching the hot water coupling first makes it easier to tighten connection with pliers.

3. Screw on coupling by hand until it is seated on the washer.

4. Using pliers, tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can

result.

5. Attach the cold water hose to the top inlet valve.

6. Screw on coupling by hand until it is seated on the washer.

7. Using pliers, tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can

result.

Check for leaks

Turn on the water faucets and check for leaks. A small amount of water might enter the

washer. You will drain this later.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose

installation or replacement dates for future reference.

• [f you connect only one water hose, you must cap off the remaining water inlet port.

• Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

SECURE THE DRAIN HOSE

1. Remove the shipping material from the power cord. Drape the power cord over the

COnSOl@,

2. Remove any cardboard used to move washer.

CZ>

Beaded tie strap

3. 2. ScrewtheIocknutontoeachfoottowithin1"(2.5cm)ofthefootbase.

Wrapthedrainhosetothelaundrytubleg,drainstandpipeorinlethoses,withthe

beadedtiestrap.Pushfastenerintothenearestholeillthebeadedtiestrap.Seeview

AorB.

1 "

(2.5 cm)

Screw the feet into the threaded holes at the front corner of the washer until the nuts

toucln the washer. Twist tlne feet to install.

NOTE: 13o not tighten the nuts until the washer is level.

If the washer faucets and the drain standpipe are recessed, put the formed end of the drain

hose into the standpipe. Tightly wrap the tie strap around the water inlet hoses and the

drain hose. See view C.

LEVEL THE WASHER

Properly leveling your washer avoids excessive noise and vibration.

Install the Front Leveling Feet

1. Prop up the front of the washer about 4" (10.2 cm) with a wood block or similar object.

[he block needs to support the weight of the washer.

(10.2 cm)

A. Threaded holes for f_et

4. Tilt the washer back and remove the wood block. Gently lower the washer to the floor.

Steps in Final Location

1. Slide the washer to its final location.

2. Tilt the washer forward until the rear of the washer is at least 4" (I 0.2 cm) off the floor. You

may hear the self-adjusting rear feet click into place. [.ower the washer to the floor.

(10.2 era)

A. 5_,lf-adjusting f_'_'t

Check the levelness of the washer by placing a level on the top edges of the washer, first

side to side, then front to back.

4. If the washer is not level, move the washer out slightly, tip back, prop up the front of the

washer with the wood block and adjust the feet up or down as necessary by twisting the

feet. Turn the feet clockwise to raise the washer or counterclockwise to lower the washer.

Repeat steps 1 through 4 until washer is level.

5. After the washer is in the final location and level, use a 9_6" or 14 mm open-end wrench

to turn the nuts counterclockwise on the feet tightly against the washer cabinet.

IMPORTANT: [f the nuts are not tight against the washer cabinet, the washer may vibrate.

COMPLETE INSTALLATION

1. Check the electrical requirements. Be sure that you have the correct electrical supply and

the recommended grounding method. See "Electrical Requirements."

2. Check that all parts are now installed. [f there is an extra part, go back through the steps to

see which step was skipped.

3. Check that you have all of your tools.

4. Check that the yellow shipping materials were completely removed from the lower back

of the washer.

5. Dispose of/recycle all packaging materials.

6. Check that the water faucets are on.

7. Check for leaks around faucets and inlet hoses.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter,

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

8. Plug into a grounded 3 prong outlet.

9. Remove the protective film on the console and any tape remaining on the washer.

10. Read "Washer Use."

11. lb test and to clean your washer, measure 1/2of the normal recommended amount of

powdered or liquid detergent and pour it into the washer basket or detergent dispenser

Ion some models). Close the lid. Select any cycle, and then pull the cycle control knob

out to start the washer. Allow it to complete one whole cycle.

WASHER USE

STARTING YOUR WASHER

Fire Hazard

Never place items in the washer that are dampened

with gasoline or other flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Doing so can result in death, explosion, or fire.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

iI!"I

WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the

IMPORTANT SAFETY INSTRUCTIONS before operating this appliance,

1. Measure detergent and pour it into the washer. If desired, add powdered or liquid color

safe bleach.

Drop a sorted load of clothes loosely into your washer.

• load evenly to maintain washer balance. Mix large and small items. Items should

move easily through the wash water.

• load only to the top of the basket as shown. Overloading can cause poor cleaning.

3. (OPTIONAl.) Add liquid chlorine bleach.

NOTE: Follow the garment and the chlorine bleach manufacturers' directions for proper

use. Undiluted bleach will damage any fabric it touches. The damage appears as rips,

holes, tears, or color loss and may not show up until several washings later, qb avoid

spilling, use a cup with a pouring spout. Do not let bleach splash, drip, or run down into

the washer basket. Always measure liquid chlorine bleach. Do not guess. [_3o not use

more than the manufacturer's recommended amount for a full load. Use less with a

smaller load size.

Styles 1 and 2: With liquid chlorine bleach dispenser/on some models)

• Use only liquid chlorine bleach in this dispenser. Do not use this dispenser to add

powdered chlorine or color-safe bleach to your wash load. Pour measured liquid

chlorine bleach into the liquid chlorine bleach dispenser. Bleach is immediately fed

into washer and is diluted automatically during the wash part of the cycle.

• Dispensers on Timed Bleach models automatically dispense bleach at the proper time

in the cycle for optimal performance, ensuring the cleanest and brightest loads.

Style 1 Style 2

Liquid chlorine Dispenser for

bleach dispenser fTn'ledBleach modek

(on some modek;

Style 3: Without liquid chlorine bleach dispenser/on some models)

• let the washer fill and begin agitating the load.

• Add bleach 5 minutes into the wash cycle for best cleaning and so that bleach can be

removed in the rinse cycle. Pour bleach around the agitator, not directly onto the load

to avoid damaging clothing or other items in the load.

(OPTIONAl.) Add liquid fabric softener.

NOTE: Do not spill or drip any fabric softener onto the clothes. Undiluted fabric softener

can stain fabrics. Always dilute fabric softener with warm water. Using too much fabric

softener can make some items (diapers and towels) nonabsorbent. If this happens, do not

use it in every load, or use less of it in each load.

Style 1: With liquid fabric softener dispenser/on some models)

• Use only liquid fabric softener in this dispenser. Pour measured liquid fabric softener

into the dispenser. Softener is added automatically during the rinse portion of the

cycle. Dilute liquid fabric softener by filling the dispenser with warm water until

liquid reaches the underside of the rim. See max fill line arrows.

Style 2: Without liquid fabric softener dispenser/on some models)

• [n the final rinse only, add fabric softener that has been diluted with 1/2to 1 cup

(125 to 250 m[.) warm water.

Close the washer lid. Washer will not agitate or spin with the lid open.

Turn the [.OAD SIZE or WATER I.EVEI. selector to the correct setting for your wash load

and the type of fabric being washed.

• You may change the load size or water level selection after the washer has started

filling by turning the selector to a different setting.

• On models with a variable Load Size or Water [.evel control, you should turn the

knob to RESET, then to desired setting.

7. Select a Wash [_mperature based on the type of fabric and soil being washed. Use the

warmest wash water safe for the fabric. Follow garment label instructions.

The Automatic Temperature Control (A[C) (on some models) electronically senses and

maintains a uniform water temperature by regulating incoming hot and cold water.

• Even in Cool wash, some warm water is let into the washer to maintain a minimum

temperature of approximately 70°F (21°C).

Temperature Guide

Wash Temp Suggested Fabrics

Hot Whites and pastels

Durable garments

Heavy soils

Warm Bright colors

Moderate to light soils

Cool Colors that bleed or fade

light soils

Cold Dark colors that bleed or fade

I.ight soils

NOTE: [n wash water temperatures colder than 60°F (15.6°C), detergents do not dissolve

well. Soils can be difficult to remove. Some fabrics can retain wear wrinkles and have

increased pilling (the formation of small lint-like balls on the surface of garments).

8. You can customize your wash by adding rinse Options to your cycle selections. This knob

has settings for:

• Extra Rinse - Selecting this option provides a second rinse. An Extra Rinse can be

added to any wash cycle.

• Cycle Signal - A tone will sound at the end of the cycle. The sound level cannot be

adjusted.

• Extra Rinse & Cycle Signal - This option combines both a Extra Rinse and a Cycle

Signal at the end of the wash cycle.

9. The SensiCare P'_System/on some models) is an integrated set of controls which work

together to provide optimal wash temperatures, agitation times, and agitation/spin speeds

based on the Fabric Select setting. The controls provide higher wash temperatures for

more aggressive, heavy-duty cycles and slightly lower temperatures on cycles for delicate

and hand wash items, to provide better fabric care. The timer knob allows you to decrease

agitation time for light soils and increase agitation time for heavy soils.

14-

10.Pushillthelimerknobandturnitclockwisetothewashcycleyouwant.Reducethe

washtimewhenusingasmallwaterlevelsetting.Pulloutthelimerknobtostartthe

washer.

Tostop or restart your washer:

• iS stop the washer at any time, push ill the Timer knob.

• lo restart the washer, close the lid lif open) and pull out the Timer knob.

WASHER CARE

CLEANING YOUR WASHER

Use a soft, damp cloth or sponge to wipe up any spills such as detergent or bleach from the

outside of your washer.

Clean your washer interior by mixing I cup (250 ml.) of chlorine bleach and 2 cups (500 mL)

of detergent. Pour this mixture into your washer and run it through a complete cycle using hot

water. Repeat this process if necessary.

Remove any hard water deposits using only cleaners labeled as washer safe.

Cleaning the liquid fabric" softener dispenser (on some models):

1. Remove dispenser by grasping top with both hands and squeezing, while pushing upward

with thumbs.

2. Rinse dispenser under warm water, then replace it.

NOTE: Some models are equipped with a liquid fabric softener dispenser. lb avoid damage to

the washer or clothing, do not wash clothes with the liquid fabric softener dispenser removed

or add detergent or bleach to this dispenser; it is for liquid fabric softener only.

WATER INLET HOSES

Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect

and replace inlet hoses if bulges, kinks, cuts, wear or leaks are found.

When replacing your inlet hoses, mark the date of replacement on the label with a permanent

marker.

MOVING AND STORAGE

Because some water may stay in the hoses, freezing can damage your washer. If storing or

moving your washer during freezing weather, winterize it.

Winterizing your washer

1. Shut off both water faucets. Disconnect and drain water inlet hoses. Pour 1 qt (1 I.) of R.V.-

type antifreeze into the basket.

2. Run washer on a drain and spin setting for about 30 seconds to mix the antifreeze and

remaining water.

3. Unplug washer or disconnect power.

To use washer again

1. Flush water pipes and hoses. Reconnect water inlet hoses. Turn on both water faucets.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug in washer or reconnect power.

3. Run the washer through a complete cycle with 1 cup (250 m]) of detergent to clean out

antifreeze.

Storage, non-use or vacation care

Operate your washer only when you are at home. If you will be on vacation or not using your

washer for an extended period of time, you should:

1. Unplug washer or disconnect power.

2. Turn off the water supply to the washer. This helps avoid accidental flooding (due to a

water pressure surge/while you are away.

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid the cost of a service call...

WASHER AND COMPONENTS

Noisy

• Is the load balanced and the washer level? The wash load should be balanced and not

overloaded. [-he washer must be level. The front feet should be properly installed and the

nuts tightened. Reset the rear leveling legs (if needed). See "Starting Your Washer."

• Did you completely remove the yellow shipping strap with cotter pins? See "Remove

Shipping Materials."

• Are the gears engaging after the drain and before spin, or is the upper part of agitator

clicking during wash? These are normal washer noises.

Leaking

• Check the following:

Are the fill hoses tight?

Are the fill hose washers properly seated?

Is the sink or drain clogged? Sink and standpipe must be able to handle 17 gal. (64 I.) of

water per minute.

Is water deflecting off the tub ring or the load? Center the tub before starting the washer.

The wash load should be balanced and not overloaded. The fill or spray rinses can deflect

off the load. The washer must be level. The front feet should be properly installed and the

nuts tightened. Reset the rear leveling legs (if needed). See "[ evel the Washer."

• Check household plumbing for leaks.

Basket crooked

• Was the washer basket pulled forward during loading? Push the basket to the center

before sta rti ng wash,

• Is the load balanced and the washer level? [he wash load should be balanced and not

overloaded. The washer must be level. The front feet should be properly installed and the

nuts tightened. Reset the rear leveling legs (if needed). See "level the Washer."

• The washer basket moves while washing. This is normal.

Agitator operation

• The top of the agitator is loose, or moves in only one direction. This is normal.

Dispensers clogged or bleach leaking

• Did you follow the manufacturer's directions when adding detergent and fabric softener

to the dispensers (on some models)? Measure detergent and fabric softener. Slowly pour

into the dispensers. Wipe up all spills. Dilute fabric softener in the fabric softener

dispenser.

• Did you put powdered or color-safe bleach into the liquid chlorine bleach dispenser (on

some models)? Add powdered or liquid color-safe bleach directly to the basket. Do not

use the chlorine bleach dispenser for color-safe bleach.

WASHER OPERATION

Washer won't run, fill, rinse or agitate; washer stops

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

• Has a household fuse blown, or has a circuit breaker tripped? Replace the fuse or reset

the circuit breaker, If the problem continues, call an electrician.

• Is the washer in a normal pause in the cycle? The washer pauses for about 2 minutes

during certain cycles. Allow the cycle to continue. Some cycles feature periods of

agitation and soak.

• Is the washer overloaded? Wash smaller loads.

• Is the lid open? The lid must be closed during operation. VVasher will not agitate or spin

with the lid open.

Washer won't drain or spin

• Is the drain hose clogged, or the end of the drain hose more than 96" (244 cm) above the

floor? See "Connect Drain Hose" for proper installation of drain hose.

• Is the lid open? The lid must be closed during operation. Washer will not agitate or spin

with the lid open.

• Is there excessive sudsing? Always measure detergent. Follow manufacturer's directions. If :::ii

you have very soft water, you might need to use less detergent.

Washer continues to fill or drain; cycle seems stuck

• Is the power cord plugged into a grounded 3 prong outlet? Plug power cord into a

grounded 3 prong outlet.

• Are you using an extension cord? Do not use an extension cord.

• Is the indicator on the Timer knob properly lined up with a cycle? [urn the Timer knob to

the right slightly and pull to start.

• Are the water inlet valve screens clogged? Turn off the water and remove inlet hoses from

the washer. Remove any accumulated film or particles. Reinstall hoses, turn on water and

check for leaks.

Are both the hot and cold water faucets turned on? Turn on the water.

Is the water inlet hose kinked? Straighten the hoses.

Does the water level seem too low, or does the washer appear to not fill completely? The

top of the agitator is much higher than the highest water level. This is normal and

necessary for clothes to move freely.

• Is the top of drain hose mower than the water level in washer? The top of the hose must be

higher than the water level in the washer for proper operation. See "Drain System."

• Does the drain hose fit too tightly in the standpipe, or is it taped to the standpipe? [he

drain hose should be loose yet fit securely. Do not seal the drain hose with tape. [-he hose

needs an air gap. See "Secure the Drain Hose."

Wash/Rinse temperature not what I selected

• Are the hot and cold water inlet hoses reversed? See "Connect the ]nJet Hoses" for more

information. As your frequency of loads washed increases, the water temperature may

decrease for hot and warm temperatures. [his is normal.

WASHER RESULTS

Load too wet

• Did you use the right cycle for the load being washed?

Select a cycle with a higher spin speed (if available).

• Did you use a cold rinse? Cold rinses leave loads wetter than warm rinses. This is normal.

Residue or lint on load

• Did you sort properly? Sort lint givers (towels, chenille) from lint takers (corduroy,

synthetics). Also sort by color.

• Did you overload the washer? The wash load must lye balanced and not overloaded.

Clothes should move freely. I.int can lye trapped in the load if overloaded. Wash smaller

loads.

• Did you select the correct water level? The water level should be correct for the load

size. Clothes should move freely in the water.

• Did you use enough detergent? Follow manufacturer's directions. Use enough detergent

to hold the lint in the water.

• Did you line dry your clothing? If so, you can expect some lint on the clothing.

• Check the following:

Was paper or tissue left in the pockets?

Is your water colder than 60°F (15.6°C)? Wash water colder than 60°F (I 5.6°C) may not

completely dissolve the detergent.

Did you use the proper cycle time for the load? Reducing wash time (duration) is another

way to reduce lint.

Stains on load

• Did you follow the manufacturer's directions when adding detergent and fabric

softener? Measure detergent and fabric softener. Use enough detergent to remove soil and

hold it in suspension. Dilute fabric softener and add to the rinse portion of a cycle only.

Do not drip fabric softener on clothes.

• Is there above average iron (rust) in water? You may need to install an iron filter.

• Did you properly sort the load? Sort dark clothes from whites and lights.

• Did you unload the washer promptly? [b avoid dye transfer, unload the washer as soon as

it stops.

Load is wrinkled

• Did you unload the washer promptly? Unload the washer as soon as it stops.

• Did you use the right cycle for the load being washed?

Use the cycle for Casual or Permanent Press clothes or another cycle with low spin speeds

(if available) to reduce wrinkling.

• Did you overload the washer? The wash load must be balanced and not overloaded.

loads should move freely during washing.

[b reduce wrinkling of permanent press clothes and some synthetic knits, use a large load

size to provide more space.

• Are the hot and cold water hoses reversed? Check that the hot and cold water hoses are

connected to the right faucets. See "Connect the Inlet Hoses."

Load is tangled or twisted

• Did you overload the washer? [he wash load must be balanced and not overloaded.

loads should move freely during washing.

• Did you wrap items around the agitator? Drop items loosely into the washer. Do not

wrap items around the agitator.

Gray whites, dingy colors

• Did you properly sort the load? Dye transfer can occur when mixing whites and colors in

a load. Sort dark clothes from whites and lights.

• Was the wash temperature too low? Use hot or warm washes if safe for the load. Make

sure your hot water system is adequate to provide a hot water wash.

• Did you use enough detergent, or do you have hard water? Use more detergent for

washing heavy soils in cold or hard water.

• Are the hot and cold water hoses reversed? Check that the hot and cold water hoses are

connected to the right faucets. See "Connect the Inlet Hoses."

Garments damaged

• Check the following:

Were sharp items removed from pockets before washing? Empty pockets, zip zippers,

snap or hook fasteners before washing.

Were strings and sashes tied to avoid tangling?

Were items damaged before washing? Mend rips and broken threads in seams before

washing.

• Did you overload the washer? The wash load must be balanced and not overloaded.

loads should move freely during washing.

• Did you add chlorine bleach properly? Do not pour chlorine bleach directly onto load.

Wipe up bleach spills. Undiluted bleach will damage fabrics. Do not place load items on

top of the bleach dispenser when loading and unloading the washer/on some models).

• Did you follow the manufacturer's care label instructions?

ASSISTANCE OR SERVICE

Before calling for assistance or service, please check "Troubleshooting." It may save you the

cost of a service call. If you still need help, follow the instructions below.

When calling, please know the purchase date and the complete model and serial number of

your appliance. This information will help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you use only factory specified

parts. Factory specified parts will fit right and work right because they are made with the same

precision used to build every new Maytag _<appliance.

lb locate factory specified parts in your area, call the following customer assistance telephone

number or your nearest designated service center.

IN THE U.S.A.

Call the Maytag Services, LLC Customer Assistance toll free:

1-800-688-9900.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing impaired, limited vision,

etc.).

• Referrals to local dealers, repair parts distributors and service companies. Maytag _

appliances designated service technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in the United States.

lb locate the Maytag _appliances designated service company in your area, you can also

look in your telephone directory Yellow Pages.

For further assistance

If you need further assistance, you can write to Maytag _appliances with any questions or

concerns at:

Maytag Services, ].[.C

A[TN: CAIR _"Center

RO. Box 2370

Cleveland, TN 37320-2370

Please include a daytime phone number in your correspondence.

IN CANADA

Call the Whirlpool Canada [.P Customer Interaction Centre toll free: 1-800-807-6777.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Referrals to local dealers, repair parts distributors, and service companies. Whirlpool

Canada I.P designated service technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Whirlpool Canada I.P with any questions or

concerns at:

Customer Interaction Centre

Whirlpool Canada I.P

1901 Minnesota Court

Mississauga, Ontario [.5N 3A7

Please include a daytime phone number in your correspondence.

MAYTAG CORPORATION MAJOR APPLIANCE WARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Maytag Corporation

or Maytag Limited (hereafter "Maytag") will pay for Factory Specified Parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Maytag

designated service company. This limited warranty applies only when the major appliance is used in the country in which it was purchased.

ITEMS MAYTAG WILL NOT PAY FOR

1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair house fuses or to correct house wiring or

plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of

products not approved by Maytag.

5. Any food loss due to refrigerator or freezer product failures.

6. Replacement parts or repair labor costs for units operated outside the United States or Canada.

7. Pickup and delivery. This major appliance is designed to be repaired in the home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service in remote locations.

10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with published installation instructions.

11. Replacement parts or repair labor costs when the major appliance is used in a country other than the country in which it was purchased.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. MAYTAG SHALL

NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS

MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR

PROVINCE TO PROVINCE.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Maytag dealer to determine if another warranty applies.

Ifyou need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," additional help can be found by checking the "Assistance or