Amana NGD5700BW0 Le manuel du propriétaire

Marque: Amana

Modèle: NGD5700BW0

Catégorie: Sèche-linge électriques

Taper: Le manuel du propriétaire

Ce manuel convient également à

__TflGn_ _

Use & Care Guide

Guide d'utilisation et d_entretien

ELECTRONICDRYER

SI_CHEUSEi_LECTRONIQUE

o0 °

Para obtener acceso

al Manual de uso y

cuidado en espaSol, o para

obtener iPformaci6n adicional

acerca de su producto, visite:

www.amana.com.

Ifyou have any problems or questions, visit us at www.amana.com

Pour tout probleme ou question, consulter www.amana.com

W10562495A

WlO572490A - SP

TABLE OF CONTENTS

DRYER SAFETY ....................................................................... 2

ACCESSORIES ........................................................................ 4

CHECK YOUR VENT SYSTEM FOR GOOD AIRFLOW ............ 5

CONTROL PANEL AND FEATURES ......................................... 6

CYCLE GUIDE .......................................................................... 7

USING YOUR DRYER .............................................................. 8

CYCLE STATUS iNDiCATORS ................................................ 10

ADDiTiONAL FEATURES ....................................................... 10

DRYER CARE ......................................................................... 11

TROUBLESHOOTING ............................................................ 13

WARRANTY ............................................................................ 16

ASSISTANCE OR SERVICE ..................................... Back Cover

TABLE DE MATIERES

S¢:CURIT¢: DE LA S¢:CHEUSE ............................................... 17

ACCESSOIRES ...................................................................... 19

VC:RIFICATION D'UNE CiRCULATiON D'AIR ADFtQUATE

POUR LE SYST#ME D'FtVACUATION .................................... 20

TABLEAU DE COMMANDE ET CARACTERISTIQUES .......... 21

GUIDE DES PROGRAMMES .................................................. 22

UTILISATION DE LA S¢:CHEUSE ........................................... 23

TC:MOINS LUMINEUX DE PROGRAMME .............................. 25

CARACTFtRISTIQUES SUPPLC:MENTAIRES .......................... 26

ENTRETIEN DE LA S¢:CHEUSE ............................................. 27

DEPANNAGE .......................................................................... 29

GARANTI E.............................................................................. 35

ASSISTANCE OU SERVICE ........................... Couverture arriere

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions,

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructionsare not followed.

- "Risk of Fire"

- Clothes dryer installation must be performed by a qualified installer.

- Install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install a clothes dryer with flexible plastic venting materials or flexible metal

(foil type) duct. If flexible metal duct is installed, it must be of a specific type identified

by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting

materials are known to cofiapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire.

- To reduce the risk of severe injury or death, follow all installation instructions.

- Save these instructions.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

In the State of Massachusetts, the following installation instructions apply:

[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

e Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

® If you cannot reach your gas supplier, call the fire department.

- installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1iNFPA 54.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSl/NFPA 70.

iMPORTANT: When discarding or storing your old clothes dryer, remove the door.

iMPORTANTSAFETYiNSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

[] Read all instructions before using the dryer.

[] Do not place items exposed to cooking oils in your dryer.

kems contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

[] Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

[] Do not reach into the dryer if the drum is moving.

[] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this

Use and Care Guide or in published user-repair

instructions that you understand and have the skills to

carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Clean lint screen before or after each load.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See "Electrical Requirements" located in the installation

instructions for grounding instructions.

SAVE THESE iNSTRUCTIONS

ACCESSORIES

Enhance your new washer and dryer with the following

genuine Whirlpool accessories. For more information

on options and ordering, call 1-886-616-2664, or visit us

at: www.amana.com/help. In Canada, call

1-866-587-2002 or visit us at www.amana.com/help

15" Pedestal

Color-matched pedestals raise the washer

and dryer to a more comfortable working

height. The large drawer provides convenient

storage.

Stack Kit

If space is at a premium, the stack kit

allows the dryer to be installed on top

of the washer.

Worksurface

The worksurface bridges the washer

and dryer, and provides a convenient

working and storage area.

CHECK YOUR VENT SYSTEM FOR GOOD AIRFLOW

Fire Hazard

Use a heavy metal vent,

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

Good airflow

Along with heat, dryers require good airflow to efficiently dry

laundry. Proper venting will reduce your drying times and

improve your energy savings. See Installation Instructions.

The venting system attached to the dryer plays a big role

in good airflow.

Service calls caused by improper venting are not covered

by the warranty and will be paid by the customer, regardless

of who installed the dryer.

Maintain good airflow by:

[] Cleaning your lint screen before each load.

[] Replace plastic or foil vent material

with 4" (102 mm) diameter heavy, rigid

vent material.

[] Use the shortest length of vent possible.

[] Use no more than four 90° elbows in a vent system;

each bend and curve reduces airflow.

Better_

[]

Remove lint and debris from the exhaust hood.

Remove lint from the entire length of the vent system

at least every 2 years. When cleaning is complete, be

sure to follow the Installation Instructions supplied with

your dryer for final product check.

Clear away items from the front of the dryer.

Use Automatic Cycles for better fabric care and energy savings

Use the Automatic Cycles to provide the most energy savings and enhanced fabric care from the dryer. During Automatic Cycles,

drying air temperature and moisture level are sensed in the load. This sensing occurs throughout the drying cycle and the dryer

shuts off when the load reaches the selected dryness. Use the NORMAL dryness level to provide optimal energy savings.

With Manual Cycles, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to

over-drying. Use Manual Cycles for the occasional damp load that needs a little more drying time or when using the drying rack.

CONTROL PANEL AND FEATURES

NOTE: The control panel features a sensitive surface that responds

to a light touch of your finger. To ensure your selections are registered,

touch the control panel with your finger tip, not your fingernail. When

selecting a setting or option, simply touch its name.

_ HEAVY

DUTY

CC) CID

NORMAL/

DELICATES

TIME DRY __

POWER

Touch to turn the dryer on and off. Touch to stop/cancel

a cycle at any time.

CYCLE CONTROL KNOB

Use your dryer's cycle control knob to select available

cycles on your dryer. Turn the knob to select a cycle for

your laundry load. Automatic Cycles are Heavy Duty,

Normal, and Delicates. Manual Cycles are Quick Dry and

Time Dry. See "Cycle Guide" for detailed descriptions of

cycles.

START/PAUSE

Touch and hold until the LED comes on to start a cycle,

or touch once while a cycle is in process to pause it.

LED DISPLAY AND SETTINGS

When you select a cycle, its default settings will light up

and the Estimated Time Remaining (for Automatic Cycles)

or actual time remaining (for Manual Cycles) will be

displayed. For times longer than 99 minutes, hours

will be displayed followed by minutes.

Touch TEMP or DRYNESS LEVEL to adjust cycle settings.

See "Cycle Guide" for available settings on each cycle.

Not all settings are available with all cycles.

-/+ (Adjust Drying Time)

Touch "+" or "-" with Manual Cycles to increase or

decrease the length of a Time Dry or Quick Dry cycle.

Temp

When using Manual Cycles, you may select a dry

temperature based on the type of load you are drying.

Use the warmest setting safe for the garments in the

load. Follow garment label instructions.

NOTE: Automatic Cycles use a preset temperature that

is not adjustable.

Dryness Level

When using Automatic Cycles, you may select a

Dryness Level based on the type of load you are drying.

NOTE: Dryness Level is for use with Automatic Cycles

only.

Cycle Status Lights

The indicator lights on the display will let you know

cycle and dryer status. For more information, see

"Cycle Status Indicators."

Adjust Drying f_me

_ Check Vent

Less

Efficiency Monitor _ _

O OPTIONS

Use to select available options for your dryer.

Control Lock

Use to lock the controls of the dryer and avoid

an accidental change in cycle options or preferences

during a drying cycle.

NOTE: The Control Lock function may be enabled

when recovering from a power failure. To unlock the

control, touch and hold CONTROL LOCK for at least

3 seconds.

CYCLE GUIDE- AUTOMATIC CYCLES

Settings and options shown in bold are default settings for that cycle.

Not all settings and options are available on each cycle.

Use Automatic Cycles for better fabric care and energy savings

The dryer senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness level.

Use the NORMAL dryness level to provide optimal energy savings.

items to dry:

, Drying Dryness Default I ; _ i,,

_ycle: Temperature: Level: Time: ' _ycle ue_aus:

Heawweight items Heavy High More 45 _ Offers stepped drying starting with High heat

such astowels or Duty Normal _ followed by Medium heatfor enhanced fabric care

heavywork clothes Less and energysavings.

Workclothes, casual Normal Medium More 38 _ Uses Medium heatto dry large loadsof mixed

wear,mixed cottons, Normal _ fabrics and items. Normal is the preferred energy

sheets, corduroys Less cycle.

Undergarments, Delicates Low More 28 _ Uses Low heatto gently dry delicate items.

blouses, lingerie, Normal

performance wear Less

CYCLE GUIDE -- MANUAL CYCLES

Settings and options shown in bold are default settings for that cycle.

Not all settings and options are available on each cycle.

Selecting the Drying Temperature

A High heat setting may be used for drying heavyweight items such as towels and work clothes.

A Low to Medium heat setting may be used for drying medium-weight items such as sheets, blouses, dresses, underwear,

permanent press fabrics, and some knits.

Use a no heat (air dry) setting for foam, rubber, plastic, or heat-sensitive fabrics.

Line dry bonded or laminated fabrics.

NOTE: If you have questions about drying temperatures for various loads, refer to the care label directions.

items to dry:

Small loads and

sportswear

Any load

NOTE: Select Air

Only to dry foam,

rubber, plastic, or

heat-sensitive

fabrics.

Cycle:

Quick Dry

Time Dry

Temperature:

High

Medium

Low

Air Only

High

Medium

Low

Air Only

Time:. ....... Cycle Details: ...............

13 _ For small loads of 3-4 items.

(the last

Time Dry

time set)

Use to dry items to a damp level for items that do not require anentire drying cycle. Select a drying temperature based on the type

of fabrics inyour load. If you are unsure of the temperature to select

for a load, select the lower setting rather than the higher setting.

Load Size Recommendations

For best results, follow the wet load size recommendations noted

for each cycle.

_ mall load: Fill the dryer drum with 3-4 items,

not more than 1/4 full.

_ Medium load: Fill the dryer drum up to about 1/2 full.

Large load: Fill the dryer drum up to about 3/4 full.

Do not pack tightly. Items need to tumble freely.

USING YOUR DRYER

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injuryto

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance.

1, Clean the lint screen

Clean the lint screen before each load. Pull the lint screen

straight up. Roll lint off the screen with your fingers. Do not rinse

or wash screen to remove lint. Wet lint is hard to remove. Push

the lint screen firmly back into place.

For additional cleaning information, see "Dryer Care."

2. Load the dryer

o©o

-- m

Open the door by pulling on the handle. Place laundry in the

dryer. Add a dryer sheet to wet load, if desired. Close the door.

iMPORTANT: Do not tightly pack the dryer. Items need

to tumble freely. Tightly packing can lead to poor drying

performance and may increase wrinkling and tangling.

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death

or fire.

3.Touo.POWER

CZ3

Touch POWER to turn on the dryer.

4. Select the desired cycle

NORMAL

HEAVY

DELICATES DUTY

QUICK DRY

TIME DRY

Select the desired cycle for your load. See the "Cycle Guide"

for more information about each cycle. Not all cycles are

on all models.

5. Adjust cycle settings, if desired

Check Vent

Effidency Monitor

H_#h wet .....CoolUo_,, Do,,e

Air Only

You may adjust different settings, depending on whether you

have selected an Automatic Cycle or Manual Cycle. See the

"Cycle Guide" for detailed information.

NOTE: Not all options and settings are available with all cycles.

Not all cycles are on all models.

Automatic Cycles:

You can select a different dryness level, depending on your

load. Touch DRYNESS LEVEL to scroll to More, Normal, or

Less. Selecting More, Normal, or Less automatically adjusts

the dryness level at which the dryer will shut off. Once a

dryness level is set, it cannot be changed without stopping

the cycle.

Automatic Cycles give the best drying in the shortest time.

Drying time varies based on fabric type, load size, and

dryness setting. Drying time is estimated and may change

throughout the cycle. Drying time can not be changed on

Automatic Cycles.

NOTE: Automatic cycles use a preset temperature that is not

adjustable.

Manual Cycles:

When you select a Manual Cycle, the default

time appears in the display. Touch + and -

to increase or decrease the time in 1-minute

increments. Touch and hold to change the

time in 5-minute increments.

The default temperature may be changed by

pressing Temp until the desired dry temperature is lit. Once a

cycle has started, the temperature can be changed after first

pausing the cycle.

6. Touch and hold START/PAUSE

to begin cycle

CZD

Hold to Start

Touch and hold START/PAUSE to begin the cycle.

7. Remove garments promptly

after cycle is finished

Promptly remove garments after cycle has completed

to reduce wrinkling.

Changing the Automatic Cycle settings

to increase or decrease drying time

If all your loads on all Automatic Cycles are consistently

less dry or more dry than you would like, you may change

the default settings to increase or decrease the default

dryness level.

Your automatic drying settings can be adjusted to adapt to

different installations, environmental conditions, or personal

preference. This change is retained and will affect all of your

Automatic Cycles, not just the current cycle/load. There are

5 drying settings, which are displayed using the time

display:

F1 Factory preset dryness level.

F2 Slightly drier clothes, 15% more drying time.

F3 Much drier clothes, 30% more drying time.

F4 Slightly wetter clothes, 15% less drying time.

F5 Much wetter clothes, 30% less drying time.

To change the drying settings:

NOTE: The settings cannot be changed while the dryer

is running or paused. The dryer must be in standby mode

(power is off) to adjust the default settings.

1. Before starting a cycle, touch and hold DRYNESS

LEVEL for 6 seconds.

2. Touch DRYNESS LEVEL to select the dryness level

shown in the time display: F1, F2, F3, F4, or F5.

3. Touch START/PAUSE to save the new dryness level

setting.

CYCLE STATUS INDICATORS ADDITIONAL FEATURES

Check Vent

Efficiency Monitor

ili iiiilli!i i!ii i:i !i iii i"ili

The Cycle Status Indicators show the progress of a cycle.

Check Vent

This indicator will show the status of airflow through the

dryer for the dryer's life. During the sensing phase at the

beginning of the cycle, the Check Vent light will come on

if a blocked vent or low airflow issue is detected. This light

will stay on for the entire cycle, but will turn off at the end

of the cycle. This feature is available during Automatic cycles

only. For more information on maintaining good airflow, see

"Check Your Vent System for Good Airflow."

NOTE: If there are other error issues during a cycle, the

Check Vent indicator will not light up. See "Troubleshooting"

section.

Efficiency Monitor

The Efficiency Monitor allows you to see how the settings

you select affect your energy usage within the cycle chosen.

The Efficiency Monitor indicator may change, depending on

the options and modifiers selected.

Wet

The load is still wet and/or the cycle just started.

Cool Down

The dryer has finished drying with heat, and is now tumbling

the load without heat to cool it down and reduce wrinkling.

Done

This will indicate that the selected cycle has ended and

the load may be removed from the dryer.

USING THE DRYING RACK

To obtain a drying rack for your dryer, order by calling

1-877-944-7566. You will need your model and serial

number and the purchase date. Remove and discard

any packing material before use.

Use the Drying Rack for items that you do not want to

tumble dry, such as sweaters and tennis shoes. When you

use the drying rack, the drum continues to turn, but the rack

remains stationary.

The drying rack is intended for use with the Manual Dry/

Time Dry cycles only. The drying rack cannot be used with

Automatic cycles.

To use the drying rack:

IMPORTANT: Do not remove the lint screen.

1. Open dryer door.

2. Align the two hooks on the front of the drying rack with

the holes in the dryer door opening and press down fully

into holes. Rest the rear support on the dryer back ledge.

Place wet items on top of the drying rack. Allow space

around items for air to circulate. The drying rack does

not move, but the drum will rotate; be sure to leave

adequate clearance between items and the inside of

the dryer drum. Make sure items do not hang over the

edges or between drying rack grille.

Close the door.

Select a Time Dry/Air Only, or Low Temperature cycle.

Items containing foam, rubber, or plastic must be dried

on a clothesline or by using the Air Only setting.

6. When the cycle is selected, the Estimated Time

Remaining display shows the default time. You can

change the actual time in the cycle by increasing or

decreasing the cycle time.

7. Start the dryer.

NOTE: Check the lint screen and remove any lint

accumulated from items dried on the drying rack

after the cycle is finished.

DRYER CARE

'- LEANING THE DRYER LOCATION "_

l eep dryer area clear and free from items that would I

block the airflow for proper dryer operation. This includes

1clearing piles of laundry in front of the dryer.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (460 ram) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

CLEANING THE DRYER iNTERiOR

To clean dryer drum

1. Use a mild hand dish detergent mixed at a low

concentration with very warm water, and rub with

a soft cloth.

2. Rinse well with a wet sponge or towel.

3. Tumble a load of clean clothes or towels to dry drum

Use a microfiber cloth and hot water in aspray bottle

to clean the drum and a second microfiber towel to dry.

NOTE: Garments that contain unstable dyes, such as

denim blue jeans or brightly colored cotton items, may

discolor the rear of the dryer interior. These stains are

not harmful to your dryer and will not stain future loads

of clothes. Dry unstable dye items inside out to avoid

transfer of dye.

REMOVING ACCUMULATED LiNT

From inside the Dryer Cabinet

Lint should be removed every 2 years, or more often,

depending on dryer usage. Cleaning should be done by a

qualified appliance servicer or ventilation system cleaner.

From the Exhaust Vent

Lint should be removed every 2 years, or more often,

depending on dryer usage.

CLEANING THE LiNT SCREEN

Every load cleaning

The lint screen is located in the door opening of the dryer.

The control panel has an indicator light to remind you to

clean the lint screen after each load. A screen blocked

by lint can increase drying time.

To clean:

1. Pull the lint screen straight up. Roll lint off the screen

with your fingers. Do not rinse or wash screen to remove

lint. Wet lint is hard to remove.

2. Push the lint screen firmly back into place.

iMPORTANT:

III Do not run the dryer with the lint screen loose,

damaged, blocked, or missing. Doing so can cause

overheating and damage to both the dryer and fabrics.

III If lint falls off the screen into the dryer during removal,

check the exhaust hood and remove the lint. See

"Venting Requirements" in the Installation Instructions.

As needed cleaning

Laundry detergent and fabric softener residue can build

up on the lint screen. This buildup can cause longer drying

times for your clothes, or cause the dryer to stop before

your load is completely dry. The screen is probably clogged

if lint falls off while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months,

or more frequently, if it becomes clogged due to a residue

buildup.

To wash:

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent.

Scrub lint screen with the brush to remove residue

buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel.

Reinstall screen in dryer.

_NON=USE, STORAGE, AND MOVING CARE _

Non=Use or Storage Care

Operate your dryer only when you are at home. if you will

be on vacation or not using your dryer for an extended

period of time, you should:

1. Unplug dryer or disconnect power.

2. Clean lint screen. See "Cleaning the Lint Screen."

Moving Care

For power supply cord-connected dryers:

1. Unplug the power supply cord.

2. Gas models only: Close shut-off valve in gas supply line.

3. Gas models only: Disconnect gas supply line pipe and

remove fittings attached to dryer pipe.

4. Gas models only: Cap the open fuel supply line.

5. Make sure leveling legs are secure in dryer base.

6. Use tape to secure dryer door.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

For direct-wired dryers:

1. Disconnect power.

2. Disconnect wiring.

3. Make sure leveling legs are secure in dryer base.

4. Use tape to secure dryer door.

Reinstalling the Dryer

Follow the Installation Instructions to locate, level, and

connect the dryer.

TROUBLESHOOTING

Dryer will not run Door not closed completely. Make sure the dryer door is closed completely.

START/PAUSE not touched firmly Touch and hold START/PAUSE 2-5 seconds.

or held long enough.

Household fuse is blown or circuit There may be 2 household fuses or circuit breakers for the

breaker has tripped, dryer. Check that both fuses are intact and tight, or that both

circuit breakers have not tripped. Replace the fuses or reset the

circuit breaker. If the problem continues, call an electrician.

Incorrect power supply. Electric dryers require 240-volt power supply.

Check with a qualified electrician.

Wrong type of fuse. Use a time-delay fuse.

Dryer will not heat Household fuse is blown or circuit The drum may be turning, but you may not have heat. Electric

breaker has tripped, dryers use 2 household fuses or circuit breakers. Replace the

fuses or reset the circuit breaker. If the problem continues, call

an electrician.

Incorrect power supply. Electric dryers require 240-volt power supply.

Check with a qualified electrician.

Supply line valve not open. For gasdryers, make surethat the valveon the gas supply lineis open.

Thumping noise Dryer hasn't been used in a while. This is due to temporary flat spots on the drum rollers. The

thumping sound will diminish after a few minutes.

Rattling or vibrating A small object caught between the Check the front and rear edges of the drum for small objects.

noise edges of dryer drum. Clean out pockets before laundering.

Dryer isn't properly leveled. The dryer may vibrate if not properly installed. See the

Installation Instructions. All four dryer feet should be in firm

contact with the floor.

When balled up, the load will bounce, causing the dryer to

vibrate. Separate the load items and restart the dryer.

Clicking noise On gas dryers, you may hear the gas valve clicking as it opens

and closes. This is normal.

Loud humming or

increased noise during

cycle

Clothing is balled up in dryer.

Gas valve operating.

Load is packed tightly or exhaust

vent is blocked.

Reduce load size to recommended load size in "Cycle Guide."

Run the dryer for 5-10 minutes. Hold your hand under the

outside exhaust hood to check air movement. Ifyou do not feel air

movement, clean exhaust system of lint or replace exhaust vent with

heaw metal or flexible metal vent. See the Installation instructions

Clothes are not drying Lint screen is clogged with lint. Clean lint screen before each load.

satisfactorily or drying

times are too long The exhaust vent or outside Run the dryer for 5-10 minutes. Hold your hand under

exhaust hood is clogged with lint, the outside exhaust hood to check air movement. If you

restricting air movement, do not feel air movement, clean exhaust system of lint

or replace exhaust vent with heavy metal or flexible metal vent.

See the Installation Instructions.

The exhaust vent is not the correct Check that the exhaust vent is not too long or has

length, too many turns. Long venting will increase drying times.

See the Installation Instructions.

The exhaust vent diameter is not Use 4" (102 mm) diameter vent material.

the correct size.

The dryer is not level. Clothes not contacting the moisture sensors during Automatic

cycles. See "Level Dryer" in the Installation Instructions.

The Air Only temperature setting Select the correct temperature for the types of garments

has been selected, being dried. See "Cycle Guide."

TROUBLESHOOTING

f First try the solutions suggested here or visit our website at www.amana.comihelp for assistance

and to possibly avoid a service call.

Clothes are not drying

satisfactorily or drying

times are too long (cont.)

The load is too large and heavy

to dry quickly.

Separate the load to tumble freely.

Reduce load size to recommended load size in "Cycle Guide."

Fabric softener sheets are blocking The air outlet grille is just inside the door, behind the lint screen.

the grille. Check that it is not blocked by a fabric softener sheet.

Use only one fabric softener sheet, and use it only once.

The dryer is located in a room with Proper operation of dryer cycles requires temperatures above

temperature below 45°F (7°C). 45°F (7°C).

The dryer is located in a closet. Closet doors must have ventilation openings at the top

and bottom of the door. The front of the dryer requires

a minimum of 1" (25 mm) of airspace, and, for most

installations, the rear of the dryer requires 5" (127 mm).

See the Installation Instructions.

Cycle time is too short The load may not be contacting the Level the dryer. See the Installation Instructions. All four dryer

sensor strips on Automatic Cycles. feet should be in firm contact with the floor.

The automatic cycle is ending

early.

Change the dryness level setting on Automatic Cycles.

Increasing or decreasing the dryness level will change the

amount of drying time in a cycle. If loads are consistently

ending too early, see also "Changing the Automatic Cycle

settings to increase or decrease drying time."

Lint on load Lint screen is clogged with lint. Clean lint screen before each load.

Stains on load Improper use of fabric softener. Add dryer fabric softener sheets at the beginning of the cycle.

Fabric softener sheets added to a partially dried load can

stain your garments.

......Stains on drum Loose dyes in clothes. Drum stains are caused by dyes in clothing (usually blue

jeans). These will not transfer to other clothing.

Loads are wrinkled The load was not removed from Remove load promptly from dryer at the end of the cycle.

dryer at the end of the cycle. NOTE: Refer to garment care label instructions. Dry-clean-only

garments are not recommended.

The dryer was tightly packed. Dry smaller loads that can tumble freely. Results may also

_. vary depending on fabric type. .j

TROUBLESHOOTING

mfyou experience

Odors

First try the solutions suggested here or visit our website at www.amana.comihelp for assistance '_

and to possibly avoid a service call.

Recent painting, staining, or

varnishing in the area where your

dryer is located.

Ventilate the area. When the odors or fumes are gone from

the area, rewash and dry the clothing.

Load too hot Load removed before cooldown Allow the dryer to complete the cooldown portion of the cycle

portion of cycle complete, before removing the load.

Using Manual Cycles with a high

temperature setting.

Select an Automatic Cycle with a lower heat setting to avoid

overdrying the load.

"PF" (power failure)

%2" Diagnostic Code

(low or no line voltage

condition)

"F# E#" (F1 El, F3 El, etc.)

variable service codes

Check Vent indicator is lit

The drying cycle has been

interrupted by a power failure.

There may be a problem with your

home power supply, keeping the

dryer's heater from turning on.

The dryer is in need of service.

The lint screen or vent is clogged;

the vent is crushed or kinked or

has too many turns.

Touch and hold START to restart the dryer. NOTE: The Control

Lock function may be enabled when recovering from a power

failure. To unlock the control, touch and hold CONTROL LOCK

for at least 3 seconds.

The dryer will continue to run when this diagnostic code is

present. Touch any pad to clear the code from the display

and return to the estimated time remaining.

NOTE: This error will only show during the initial installation.

Try the following:

Check to see if a household fuse has blown or circuit breaker

has tripped. Electric dryers use two household fuses or

breakers. Replace the fuse or reset the circuit breaker.

Confirm that the power cord is properly installed. Refer to

the Installation Instructions for details.

Select a Manual Cycle (heated), and restart the dryer.

If the message persists, consult a qualified electrician.

If a code beginning with an "F" appears in the display,

alternating between F# and E#, the dryer control has

detected a problem that requires service. Call for service.

The dryer will continue to run when this indicator is lit.

Try the following:

• Clean lint screen.

• Check to see if the vent run from the dryer to the wall is

crushed or kinked.

• Confirm that the vent run from the dryer to the wall is free

of lint and debris.

• Confirm that the exterior vent exhaust hood is free of lint

and debris.

• Confirm that your vent system falls within the recommended

run length and number of elbows for the type of vent you

are using. Rder to "Plan Vent System" inthe Installaton

Instructions for details.

• Select a Manual Cycle (heated), and restart the dryer.

• If the indicator remains lit, have your entire home venting run

cleaned.

WHIRLPOOL CORPORATION LAUNDRY WARRANTY

LiMiTED WARRANTY

For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions

attached to or furnished with the product, Amana, Admiral, Estate, Inglis, or Roper brands of Whirlpool Corporation or Whirlpool

Canada LP (hereafter "Whirlpool") will pay for Factory Specified Replacement Parts and repair labor to correct defects in materials or

workmanship that existed when this major appliance was purchased.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

Service must be provided by a company designated by Whirlpool to service Amana, Admiral, Estate, Inglis, or Roper brand appliances.

This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in

which it was purchased. This limited warranty is effective from the date of original consumer purchase. Proof of original purchase date

is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters, or water filters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Pick up and delivery. This major appliance is intended to be repaired in your home.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized company designated by Whirlpool to service Amana, Admiral, Estate, Inglis, or Roper brands is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Whirlpool's published installation instructions.

10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or

cannot be easily determined.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY iMPLIED WARRANTY OF MERCHANTABILITY OR iMPLIED WARRANTY OF FITNESS

FOR A PARTICULAR PURPOSE, ARE LiMiTED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and

provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply

to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to

province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. if you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR iNCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Whirlpool, Amana, Admiral, Estate, Inglis, or Roper dealer to

determine if another warranty applies.

If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. Ifyou are unable to resolve

the problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by

calling the following numbers for assistance: In the U.S.A., call 800=843=0304 for Amana brand products; 800-688-9920 for Admiral

brand products; 800=253=1301 for Estate brand products, or 800-447=6737 for Roper brand products. For assistance In Canada,

call: 800=807=6777 for Amana, Admiral, Estate, Inglis, or Roper brand products. 1/12

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in=warranty service,

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need

it. You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

S] CURITE DE LA S] CHEUSE

Votre s_curit_ et celle des autres est tr_s importante.

Nous donnons de nombreux messages de s6curit6 importants darts ce manueJ et sur votre appareil m6nager. Assurez-vous de

toujours lire tous Jesmessages de s6curit6 et de vous y conformer.

Voici Jesymbole d'aJerte de securit6.

Ce symbole d'aJerte de s_curit6 vous signaJe Jesdangers potentieJs de d6c_s et de bJessures graves h vous

et h d'autres.

Tousles messages de s6curit6 suivront JesymboJe d'aJerte de s6curit6 et Je mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient :

Risque possible de d_c_s ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d_c_s ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de s6curit6 vous diront queJ est le danger potentiel et vous disent comment r6duire Jerisque de bJessure et

ce qui peut se produire en cas de non-respect des instructions.

AVER r |SSEMENT - d,i.ooodi ,,

L'installation de la s_cheuse _ linge doit 6tre effectu_e par un installateur qualifi_.

installer la s6cheuse conforrn6rnent aux instructions du fabricant et aux codes Iocaux.

Ne pas installer de s_cheuse h linge avec des rnat_riaux d'_vacuation en plastique

souple ou un conduit rn6tallique souple (de type papier d'alurniniurn). Si un conduit

rn6tallique souple est installS, celui-ci doit 6tre d'un type sp_cifique identifi_ par le

fabricant de I'appareil et convenir _ une utilisation avec les s_cheuses _ linge. Les

rnat_riaux d'_vacuation souples sont connus pour s'affaisser, 6tre facilernent _cras_s

et bloquer la charpie. Ces situations obstrueront le d_bit d'air de la s_cheuse _ linge et

augrnenteront le risque d'incendie,

Pour r_duire le risque de blessure grave ou de d_c_s, suivre routes

les instructions d'installation.

Conserver ces instructions,

Avertissements de la proposition 65 de I'#tat de Californie •

AVERTISSEMENT " Ce produit contient au moins un produit chimique connu par I'E_tatde Californie pour _tre & I'origine de

cancers.

AVERTISSEMENT ' Ce produit contient au moins un produit chimique connu par I'Etat de Californie pour 6tre & I'origine de

malformations et autres d6ficiences de naissance.

Dans I'Etat du Massachusetts, les instructions d'installation suivantes sont applicables :

[] Les travaux d'installation et reparation doivent 6tre ex6cutes par un plombier ou tuyauteur qualifie ou licenci6, ou par le

personnel qualifie d'une entreprise licenciee par I'l_tat du Massachusetts.

[] Si une vanne & boisseau spherique est utilisee, elle doit comporter une manette "T".

[] Si un conduit de raccordement flexible est utilis6, sa Iongueur ne doit pas d6passer 3 pi.

AVERTISSEMENT : Pour votre s6curit6, les renseignements dans ce manuel doivent

_tre observes pour r_duire au minimum les risques d'incendie ou d'e×plosion ou pour

6viter des dommages au produit, des blessures ou un d_c_s.

- Ne pas entreposer ou utiliser de I'essence ou d'autres vapeurs ou liquides

inflammables & proximit_ de cet appareil ou de tout autre appareil _lectrom_nager.

- QUE FAIRE DANS LE CAS D'LINE ODEUR DE GAZ :

® Ne pas tenter d'allumer un appareil.

• Ne pas toucher & un commutateur electrique; ne pas utiliser le t_16phone se trouvant

sur les lieux.

• l_vacuer tous les gens de la piece, de I'_difice ou du quarrier.

o Appeler imm_diatement le fournisseur de gaz d'un t_l_phone voisin. Suivre ses

instructions.

®,& defaut de joindre votre fournisseur de gaz, appeler les pompiers.

- L'installation et I'entretien doivent _tre effectu_s par un installateur qualifi_, une

agence de service ou le fournisseur de gaz.

AVERTISSEMENT : L'odorat ne permet pas toujours la detection d'une fuite de gaz.

Les distributeurs de gaz recommandent I'emploi d'un detecteur de gaz (homologation UL ou CSA).

Pour d'autre information, contacter le foumisseur de gaz local.

En cas de detection d'une fuite de gaz, executer les instructions "Que faire dans le cas d'une odeur de gaz".

iMPORTANT : L'installation du gaz dolt se conformer aux codes Iocaux, ou en I'absence de codes Iocaux, au code canadien

d'installation B149.1 du gaz naturel ou du propane.

La secheuse dolt Ctre electriquement reliee & la terre conformement aux codes Iocaux, ou en I'absence de codes Iocaux, au Code

canadien de 1'61ectricit6, CSA C22.1.

iMPORTANT • Pour mettre I'ancienne secheuse au rebut ou pour la remiser, enlever la porte. I

IMPORTANTES INSTRUCTIONS DE SECURITE

AVERT|SSEMENT ; Pour r6duire le risque d'incendie, de choc 61ectfique ou de blessure Iors de I'utilisation de

la s6cheuse, il convient d'observer certaines precautions 616mentaires dont les suivantes :

[] Lire toutes les instructions avant d'utiliser la s6cheuse.

[] Ne pas placer des articles exposes aux huiles de cuisson

dans votre secheuse. Les articles contamines par des

huiles de cuisson peuvent contribuer A une r6action

chimique qui pourrait causer & la charge de s'enflammer.

[] Ne pas faire s6cher dans la machine des articles qui ont

deja et6 nettoyes, lav6s, imbibes, ou taches d'essence,

de solvants pour nettoyage & sec, d'autres substances

inflammables, ou de substances explosives puisqu'elJes

degagent des vapeurs qui peuvent provoquer un

incendie ou une explosion.

[] Ne pas permettre A des enfants de jouer sur ou A

I'int6rieur de la s6cheuse. Une surveillance etroite est

n6cessaire Jorsque la secheuse est utiJis6e pres d'eux.

[] Avant d'enlever la secheuse du service ou la jeter, enlever

la porte du compartiment de s6chage.

[] Ne pas mettre la main dans la s6cheuse si le tambour est

en mouvement.

[] Ne pas installer ni entreposer Jas6cheuse oQ eJlesera

expos6e aux intemp6des.

[] Ne pas jouer avec les commandes.

[] Ne pas r6parer ni remplacer une pi6ce de la s6cheuse ou

essayer d'en faire I'entretien a moins d'une recommandation

specifique darts le guide d'utilisation et d'entretien, ou

publi6e dans les instructions de r6paration par I'utilisateur

que vous comprenez et pouvez ex6cuter avec comp6tence.

[] Ne pas utiliser un produit assouplissant de tissu ou des

produits pour 61iminer la statique a moins qu'ils ne soient

recommand6s par le fabricant du produit assouplissant de

tissu ou du produit.

[] Ne pas utiliser la chaleur pour faire secher des articles

fabriqu6s avec du caoutchouc mousse ou des mat6riaux

semblables.

[] Nettoyer le filtre & charpie avant et apr_s chaque charge.

[] Ne pas laisser la charpie, la poussi_re, ou la salet6

s'accumuler autour du syst_me d'6vacuation ou autour de

I'appareil.

[] Un nettoyage p6riodique de I'int6rieur de la s6cheuse et du

conduit d'6vacuation dolt 6tre effectu6 par une personne

qualifi6e.

[] Pour les instructions de liaison a la terre, voir "Specifications

electriques" dans les instructions d'installation.

CONSERVEZ CES INSTRUCTIONS

ACCESSOIRES

Personnalisez votre nouvelle laveuse et s6cheuse gr&ce

aux authentiques accessoires Whirlpool suivants. Pour

plus d'informations sur les options et sur les possibilit6s

de commande, appeler le 1-866-616-2664, ou consulter :

www.amana.com/help. Au Canada, composer

le 1-866-587-2002 ou visiter notre site Web

sur www.amana.com/help.

Pi6destal de 15"

Les pi6destaux aux coloris assortis

sur61event la laveuse et la s6cheuse

pour les amener a une hauteur

d'utilisation plus confortable.

Le grand tiroir offre une capacit6

de rangement pratique.

Surface de travail

La surface de travail 6tablit la liaison

entre la laveuse et la s6cheuse

et offre une zone de travail et

d'entreposage pratique.

Ensemble de superposition

Si I'espace disponible est restreint,

I'ensemble de superposition permet

la s6cheuse d'6tre install6e par dessus

la laveuse.

VITRIFICATION D'UNE CIRCULATION D'AIR AD] QUATE

POUR LE SYSTEME D'] VACUATION

Risque d'incendie

Utiliser un conduit d'_vacuation en mdtal Iourd.

Ne pas utiliser un conduit d'_vacuation en plastique,

Ne pas utiliser un conduit d'_vacuation en feuil|e

de rn_tai.

Le non-respect de ces instructions peut causer

un d_cbs ou un incendie.

rCirculation d'air adequate

Une s6cheuse a besoin de chaleur et d'une circulation

d'air ad6quate pour s6cher efficacement le linge. Une

ventilation ad6quate r6duit les dur6es de s6chage et accroit

les 6conomies d'6nergie. Voir les Instructions d'installation.

Le systeme d'6vacuation fix6 h la s6cheuse joue un r61e

important dans la circulation de I'air.

Les interventions de d6pannage caus6es par

une ventilation incorrecte ne sont pas couvertes

par la garantie et seront a la charge du client,

quel que soit I'installateur de la s6cheuse.

Maintenir une bonne circulation d'air

en effectuant les operations suivantes :

[]

Nettoyer le filtre a charpie avant chaque

charge.

Remplacer le mat@iau de conduits

d'6vacuation en plastique ou en aluminium

par des conduits d'6vacuation Iourds et

rigides de 4" (102 mm) de diametre.

[] Toujours employer les conduits d'6vacuation les plus

courts possible.

[] Ne pas utiliser plus de quatre coudes a 90°dans

un circuit d'6vacuation car chaque inclinaison et courbe

r6duit le flux d'air.

[] Retirer la charpie et les r6sidus du clapet d'6vacuation.

[] Retirer la charpie sur toute la Iongueur du circuit

d'6vacuation au moins tousles 2 ans. Apres le

nettoyage, veuillez suivre les instructions d'installation

fournies avec la s6cheuse pour une v@ification finale

de I'appareil.

[] D6gager tout article qui se trouverait devant la s6cheuse.

fUtiliser ies prograrnrnes automatiques pour un rneiileur soin du tissu et

davantage d'_conornies d'_nergie

Utiliser les programmes automatiques pour que la s6cheuse permette de r6aliser davantage d'6conomies d'6nergie et d'apporter

un soin sup@ieur aux tissus. Durant les programmes automatiques, la temp@ature de s6chage de I'air et le niveau d'humidit6

sont d6tect6s dans la charge. Cette d6tection se produit tout au long du programme de s6chage et la s6cheuse s'6teint Iorsque

la charge atteint le degr6 de s6chage s61ectionn6. Utiliser le niveau de s6chage NORMAL (normal) pour pouvoir r6aliser un

maximum d'6conomies d'6nergie.

Avec les programmes manuels, la s6cheuse fonctionne pendant la dur6e r6gl6e, ce qui peut parfois entrainer le r6tr6cissement

ou le froissement du linge, et I'accumulation d'61ectricit6 statique due au s6chage excessif. Utiliser les programmes manuels pour

une charge encore humide n6cessitant un peu de temps suppl6mentaire ou Iorsqu'on utilise la grille de s6chage.

La page charge ...

Amana NGD5700BW0 Le manuel du propriétaire

Marque: Amana

Modèle: NGD5700BW0

Catégorie: Sèche-linge électriques

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Amana NGD5700BW0 Owner's manual

Amana NGD5700BW0 Le manuel du propriétaire

Ce manuel convient également à

Amana NGD5700BW0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents