Maytag MED7100DW Manuel utilisateur
- Catégorie
- Sèche-linge
- Taper
- Manuel utilisateur
W10596022B
W10596023B - SP
If you have any problems or questions, visit us at www.maytag.com
Pour tout problème ou question, consulter www.maytag.ca
Use & Care Guide
Guide d’utilisation et d’entretien
ELECTRONIC DRYER
SÉCHEUSE ÉLECTRONIQUE
Para obtener acceso
al Manual de uso y
cuidado en español, o para
obtener información adicional
acerca de su producto, visite:
www.maytag.com.
2
DRYER SAFETY
TABLE OF CONTENTS
DRYER SAFETY .......................................................................................2
ACCESSORIES ....................................................................................... 4
CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW ............5
CONTROL PANEL AND FEATURES ................................................. 6
CYCLE GUIDE..........................................................................................8
USING YOUR DRYER ........................................................................ 10
CYCLE STATUS INDICATORS.......................................................... 12
ADDITIONAL FEATURES .................................................................. 12
DRYER CARE ........................................................................................ 13
TROUBLESHOOTING ........................................................................ 15
WARRANTY ........................................................................................... 18
ASSISTANCE OR SERVICE ............................................. Back Cover
TABLE DE MATIÈRES
SÉCURITÉ DE LA SÉCHEUSE ........................................................ 19
ACCESSOIRES ....................................................................................21
VÉRIFICATION D’UNE CIRCULATION D’AIR ADÉQUATE
POUR LE SYSTÈME D’ÉVACUATION ............................................ 22
TABLEAU DE COMMANDE ET CARACTÉRISTIQUES ............ 23
GUIDE DE PROGRAMMES ............................................................. 26
UTILISATION DE LA SÉCHEUSE .................................................... 28
TÉMOINS LUMINEUX DE PROGRAMME ...................................30
CARACTÉRISTIQUES SUPPLÉMENTAIRES............................... 31
ENTRETIEN DE LA SÉCHEUSE ...................................................... 32
DÉPANNAGE ......................................................................................... 34
GARANTIE .............................................................................................. 38
ASSISTANCE OU SERVICE .................................Couverture arrière
3
IMPORTANT: When discarding or storing your old clothes dryer, remove the door.
4
ACCESSORIES
Customize your new washer and dryer with the following
genuine Maytag accessories. For more information on options
and ordering, contact your dealer, call us at 1-800-901-2042,
or visit: www.maytag.com/accessories.
In Canada, call 1-800-807-6777, or visit: www.maytag.ca
15" Pedestal
Color-matched pedestals raise the washer and
dryer to a more comfortable working height.
The large drawer provides convenient storage.
Stack Kit
If space is at a premium, the stack kit allows
the dryer to be installed on top of the washer.
Drying Rack
The Drying Rack provides a
stationary drying surface for items
such as sweaters and tennis shoes.
See the “Additional Features”
section for more information.
5
CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW
Good air flow
Along with heat, dryers require good air flow to efficiently
dry laundry. Proper venting will reduce your drying times and
improve your energy savings. See Installation Instructions.
The venting system attached to the dryer plays a big role
in good air flow.
Service calls caused by improper venting are not covered by
the warranty and will be paid by the customer, regardless of
who installed the dryer.
Maintain good air flow by:
n
Cleaning your lint screen before each load.
n
Replace plastic or foil vent material
with 4" (102 mm) diameter heavy, rigid
vent material.
Good
Better
n
Use the shortest length of vent possible.
n
Use no more than four 90° elbows in a vent system;
each bend and curve reduces air flow.
n
Remove lint and debris from the exhaust hood.
n
Remove lint from the entire length of the vent system
at least every 2 years. When cleaning is complete, be
sure to follow the Installation Instructions supplied with
your dryer for final product check.
n
Clear away items from the front of the dryer.
Use Sensor cycles for better fabric care and energy savings
Use the Sensor Cycles to provide the most energy savings and enhanced fabric care from the dryer. During Sensor Cycles, drying air
temperature and moisture level are sensed in the load. This sensing occurs throughout the drying cycle and the dryer shuts off when the
load reaches the selected dryness. Use the NORMAL dryness level to provide optimal energy savings.
With Timed Dry, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to over-drying.
Use Timed Dry for the occasional damp load that needs a little more drying time or when using the drying rack.
Tips for getting the best performance from your steam dryer (on some models)
n
Results may vary depending on fabric. 100% cotton
garments with wrinkle-free finish may yield better results than
those without. 100% cotton items may require additional
touching up after cycles that use steam.
n
Use of fabric softener sheet is not recommended with cycles
that use steam. It may cause temporary staining on clothes.
n
Cycles that use steam are not recommended for items that
have been starched. Wash any starched or new garments prior
to using cycles that use steam.
n The Refresh Cycle is best for smoothing out wrinkles
and reducing odors from loads consisting of dry items of
wrinkle-free cotton, cotton-polyester blend, common knits,
and synthetics.
6
CONTROL PANEL AND FEATURES
Not all features and cycles are available on all models.
NOTE: The control panel features a sensitive surface that responds
to a light touch of your finger. To ensure your selections are registered,
touch the control panel with your finger tip, not your fingernail. When
selecting a setting or option, simply touch its name.
3
2
1
4
3
2
1
4
5
5 6
6
7
OPTIONS
Use to select available options for your dryer. Not all cycles
and options are available on all models.
Drum Light
Touch to turn the LED drum light on or off. The light
will also turn on when the door is open, and turn off
automatically after about 5 minutes.
Reduce Static
Touch to add the Reduce Static option to selected
Sensor cycles (see “Cycle Guide”). The dryer will
automatically tumble, pause, and introduce a small amount
of moisture into the load to help reduce static. This option
adds approximately 8 minutes to the total cycle time.
Steam Boost
Steam Boost adds steam to the end of the Heavy Duty,
Bedding, or Normal cycle to help smooth wrinkles. Steam
Boost can be used with High or Medium heat settings.
This option adds approximately 15 minutes to the total
cycle time.
Wrinkle Prevent
If you will be unable to remove a load immediately, touch
Wrinkle Prevent to add up to 140 minutes of periodic
tumbling to help reduce wrinkling. On some cycles, you
may select the “With Steam” setting to add a short steam
cycle after 60 minutes to help smooth out wrinkles.
Damp Dry Signal
Touch to select the Damp Dry Signal. When selected, a
series of beeps will sound when the load is damp, but not
completely dry. This will allow you to take clothes out of
the load that do not need to dry completely. This option
is available on Heavy Duty, Normal, Wrinkle Control,
Bedding, and Delicates cycles. The Damp Dry Signal is
selected as a default for the Bedding cycle, as a reminder
to manually reposition bedding loads midway through the
cycle.
Cycle Signal
Use this to turn the signal indicating the end of a drying
cycle on or off.
NOTE: You may also turn off the tones that sound when
a feature, setting, or option is touched. Touch and hold
Cycle Signal for about one second to turn sounds on
or off.
Control Lock
Use to lock the controls of the dryer and avoid
an accidental change in cycle options or preferences
during a drying cycle.
Touch and hold CONTROL LOCK for 3 seconds to lock
or unlock the controls of the dryer. During this time, the
LED Display will count down 3-2-1. Once the controls
are locked, the LED Display will display “Lc” or “Loc.”
NOTE: The Control Lock function may be enabled when
recovering from a power failure. To unlock the control,
touch and hold CONTROL LOCK for at least 3 seconds.
CYCLE STATUS LIGHTS
The indicator bar on the right side of the control will let you
know what stage of the drying cycle is in process. For more
information on each stage, see “Cycle Status Indicators.”
5
6
POWER/CANCEL
Touch to turn the dryer on and off. Touch to stop/cancel
a cycle at any time.
CYCLE CONTROL KNOB
Turn the knob to select a cycle for your laundry load. Sensor
Cycles are Heavy Duty, Normal, Delicates, Sanitize (on some
models), Bedding (on some models), and Wrinkle Control
(on some models). Timed Cycles are Timed Dry and Rapid
Dry. The Steam Cycle (on some models) is Refresh. See
“Cycle Guide” for detailed descriptions of cycles.
START/PAUSE
Touch and hold until the LED comes on to start a cycle,
or touch once while a cycle is in process to pause it.
LED DISPLAY AND SETTINGS
When you select a cycle, its settings will light up and the
Estimated Cycle Time (for Sensor Cycles) or actual time
remaining (for Timed Cycles) will be displayed. On 2-digit
displays, for times longer than 99 minutes, hours will be
displayed followed by minutes.
See “Cycle Guide” for available settings on each cycle.
Not all settings are available with all cycles.
–/+ (Timed Dry Adjust)
Touch “+” or “–” with Timed Cycles to increase or
decrease the length of a Timed Dry or Rapid Dry cycle.
Temperature
When using Timed Cycles or Refresh, you may select a
dry temperature based on the type of load you are drying.
Use the warmest setting safe for the garments in the load.
Follow garment label instructions.
NOTE: Sensor Cycles use a preset temperature that is
not adjustable.
Dryness Level
When using Sensor Cycles (except for the Sanitize cycle),
you may select a Dryness Level based on the type of load
you are drying.
NOTE: Dryness Level is for use with Sensor Cycles only.
Wrinkle Prevent
If you will be unable to remove a load immediately, touch
Wrinkle Prevent to add up to 140 minutes of periodic
tumbling to help reduce wrinkling. On some cycles, you
may select the “With Steam” setting to add a short steam
cycle after 60 minutes to help smooth out wrinkles.
Energy Saver
Touch to activate the Energy Saver option, which allows
you to increase your energy savings by using a slightly
lower heat level. For automatic cycles, Energy Saver will
increase drying times by approximately 40 minutes; the
LED Display will reflect this time.
Energy Saver will default on for Normal. For optimal energy,
turn on the Energy Saver option. For optimal time, turn off
the Energy Saver option.
1
2
3
4
8
CYCLE GUIDE — SENSOR CYCLES
Settings and options shown in bold are default settings for that cycle.
If settings are changed, the new settings will be remembered. If there is a power failure, settings will return to the default.
Not all features and cycles are available on all models.
Not all settings and options are available on each cycle.
Heavyweight items Heavy High More 40 Damp Dry Signal Offers stepped drying starting
such as towels or Duty Normal Wrinkle Prevent
†
with High heat followed by Medium
heavy work clothes Less Reduce Static* heat for enhanced fabric care
Steam Boost* and energy savings.
Energy Saver
Work clothes, casual Normal Medium More 78 Damp Dry Signal Uses Medium heat to dry large
wear, mixed cottons, Normal Wrinkle Prevent
†
loads of mixed fabrics and items.
sheets, corduroys Less Reduce Static* Normal is the preferred energy
Steam Boost* cycle.
Energy Saver
Shirts, blouses, Wrinkle Control Low More 33 Damp Dry Signal Uses a stepped drying temperature
permanent press, Normal Wrinkle Prevent
†
from Medium to Low for improved
synthetics, Less Reduce Static* moisture removal and enhanced
lightweight items Energy Saver fabric care.
Undergarments, Delicates Extra Low More 28 Damp Dry Signal Uses Extra Low heat to gently
blouses, lingerie, Normal Wrinkle Prevent
†
dry delicate items.
performance wear Less Reduce Static*
Energy Saver
Large loads Sanitize High More 1:10 Wrinkle Prevent
†
This is a long cycle with high heat,
of heavyweight or which has been proven to reduce
items 70 household bacteria. This cycle is
not recommended for all fabrics.
Use for large loads of heavyweight
fabrics.
Jackets, comforters, Bedding Medium More 55 Damp Dry Signal Use for drying large, bulky items;
pillows Normal Wrinkle Prevent
†
do not overfill dryer drum. Partway
Less Steam Boost* through the cycle, the signal will
Energy Saver sound for 2 minutes to indicate
when it is time to rearrange items
for optimal drying.
Items to dry: Cycle:
Drying
Temperature:
Dryness
Level:
Default
Time:
Available
Options:
Cycle Details:
Load Size Recommendations
For best results, follow the wet load size recommendations noted
for each cycle.
Small load: Fill the dryer drum with 3–4 items, not more than
1/4 full.
Medium load: Fill the dryer drum up to about 1/2 full.
Large load: Fill the dryer drum up to about 3/4 full.
Do not tightly pack. Items need to tumble freely.
Use Sensor Cycles for better fabric care and energy savings
The dryer senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness level.
Use the NORMAL dryness level to provide optimal energy savings.
†
On steam models, you may select the “With Steam” setting to add a short steam cycle after 60 minutes. This is available only with High and Medium Drying
Temperature settings.
* On steam models only.
9
CYCLE GUIDE — TIMED CYCLES
Settings and options shown in bold are default settings for that cycle.
If settings are changed, the new settings will be remembered (except on Rapid Dry). If there is a power failure, settings will return to the
default.
Not all features and cycles are available on all models.
Not all settings and options are available on each cycle.
Any load Timed Dry High 40 Wrinkle Prevent
†
Use to dry items to a damp level for items that do
NOTE: Select Air Medium not require an entire drying cycle. Select a drying
Only to dry foam, Low temperature based on the type of fabrics in your
rubber, plastic, or Extra Low load. If you are unsure of the temperature to select
heat-sensitive Air Only for a load, select the lower setting rather than the
fabrics. higher setting.
Small loads and Rapid Dry High 26 Wrinkle Prevent
†
For small loads of 3–4 items.
sportswear Medium
Low
Extra Low
Air Only
Small loads and Air Dry 50 Wrinkle Prevent
†
For small loads of 3–4 items.
sportswear
Items to dry:
Cycle:
Drying
Temperature:
Default
Time:
Available
Options:
Cycle Details:
CYCLE GUIDE — STEAM CYCLE (on some models)
Settings and options shown in bold are default settings for that cycle.
Not all settings and options are available on each cycle.
Steam cycles are designed for use with dry loads to loosen wrinkles, reduce odors, and refresh fabrics.
Load Size Recommendations
For best results, follow the load size recommendations noted
for each cycle.
Small load: Fill the dryer drum with 3–4 items, not more than
1/4 full.
Medium load: Fill the dryer drum up to about 1/2 full.
Large load: Fill the dryer drum up to about 3/4 full.
Do not overload. Items need to tumble freely.
Shirts, blouses, Refresh Medium 22 Wrinkle Prevent
†
Use to reduce light wrinkles from loads left in the
and slacks Reduce Static* dryer too long. Do not add dryer sheets.
Items
to refresh:
Cycle:
Drying
Temperature:
Default
Time:
Available
Options:
Cycle Details:
Adjusting drying time on Timed Cycles
When you select a Timed
Cycle, the time appears in
the display. Use + and – to
increase or decrease the time
in 1-minute increments. Touch
and hold to change the time
in 5-minute increments.
The maximum dry time is 100 minutes.
Selecting the Drying Temperature
A High heat setting may be used for drying heavyweight items such
as towels and work clothes.
A Low to Medium heat setting may be used for drying
medium-weight items such as sheets, blouses, dresses,
underwear, permanent press fabrics, and some knits.
Use a no heat (air only) setting for foam, rubber, plastic,
or heat-sensitive fabrics.
Line dry bonded or laminated fabrics.
NOTE: If you have questions about drying temperatures for various
loads, refer to the care label directions.
†
On steam models, you may select the “With Steam” setting to add a short steam cycle after 60 minutes. This is available only with High and Medium Drying
Temperature settings.
†
On steam models, you may select the “With Steam” setting to add a short steam cycle after 60 minutes. This is available only with High and Medium Drying
Temperature settings.
* On steam models only.
10
USING YOUR DRYER
1. Clean the lint screen
Clean the lint screen before each load. Pull the lint screen straight
up. Roll lint off the screen with your fingers. Do not rinse or wash
screen to remove lint. Wet lint is hard to remove. Push the lint
screen firmly back into place.
For additional cleaning information, see “Dryer Care.”
2. Load the dryer
Open the door by pulling on the handle. Place laundry in the dryer.
Add a dryer sheet to wet load, if desired. Close the door.
IMPORTANT: Do not tightly pack the dryer. Items need to tumble
freely. Tightly packing can lead to poor drying performance and may
increase wrinkling and tangling.
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
3. Touch POWER/CANCEL
Touch POWER/CANCEL to turn on the dryer.
4. Select the desired cycle
Select the desired cycle for your load. See the “Cycle Guide”
for more information about each cycle. Not all cycles are on all
models.
Appearance may vary.
Appearance may vary.
11
Promptly remove garments after cycle has completed to reduce
wrinkling.
7. Touch and hold START/PAUSE
to begin cycle
Touch and hold START/PAUSE to begin the cycle.
8. Remove garments promptly
after cycle is finished
Changing the Sensor Cycle settings
to increase drying time
5. Adjust cycle settings, if desired
You may adjust different settings, depending on whether you have
selected a Sensor Cycle, Timed Cycle, or Steam Cycle (on some
models). See the “Cycle Guide” for detailed information.
NOTE: Not all options and settings are available with all cycles.
Not all cycles are on all models.
Sensor Cycles:
You can select a different dryness level, depending on your load.
Touch DRYNESS LEVEL to scroll to More, Normal, or Less.
Selecting More, Normal, or Less automatically adjusts the dryness
level at which the dryer will shut off. Once a dryness level is set, it
cannot be changed without stopping the cycle.
Sensor cycles give the best drying in the shortest time. Drying time
varies based on fabric type, load size, and dryness setting. Drying
time is estimated and may change throughout the cycle. Drying
time can not be changed on Sensor Cycles.
NOTE: Sensor Cycles use a preset temperature that is not
adjustable.
Timed Cycles:
When you select a Timed
Cycle, the time appears in
the display. Touch + and – to
increase or decrease the time
in 1-minute increments. Touch and hold to change the time in
5-minute increments.
The temperature may be changed by touching Temperature until
the desired dry temperature is lit. Once a cycle has started, the
temperature can be changed after first pausing the cycle.
Steam Cycles (on some models):
Select Refresh to reduce odors and light wrinkles in dry loads.
Do not add dryer sheets. Cycle time is estimated and may change
throughout the cycle. Cycle time can not be changed on Steam
Cycles.
6. Select any additional options
The display will show the settings for the selected cycle. To adjust
a setting, touch its name – Reduce Static, Steam Boost, or Damp
Dry Signal.
NOTE: Not all options and settings are available with all cycles.
Appearance may vary.
Appearance may vary.
Appearance may vary.
If all your loads on all Sensor Cycles are consistently not as
dry as you would like, you may change the default settings to
increase the default dryness level.
Your sensor drying settings can be adjusted to adapt to
different installations, environmental conditions, or personal
preference. This change is retained and will affect all of your
Sensor cycles, not just the current cycle/load. There are
5 drying settings, which are displayed using the time display:
01 Factory preset dryness level.
02 Slightly drier clothes, 15% more drying time.
03 Much drier clothes, 30% more drying time.
04 Slightly wetter clothes, 15% less drying time.
05 Much wetter clothes, 30% less drying time.
To change the drying settings:
NOTE: The settings cannot be changed while the dryer
is running or paused. The dryer must be in standby mode
(power is off) to adjust the default settings.
1. Before starting a cycle, touch and hold DRYNESS LEVEL
for 6 seconds.
2. Touch DRYNESS LEVEL to select the dryness level shown
in the time display: 01, 02, 03, 04 or 05.
3. Touch START/PAUSE to save the new dryness level
setting.
12
ADDITIONAL FEATURES
2. Align the two hooks on the front of the drying rack with the
holes in the dryer door opening and press down fully into
holes. Rest the rear support on the dryer back ledge.
USING THE DRYING RACK
To purchase a drying rack for your dryer, order by calling
1-877-944-7566. You will need your model and serial number
and the purchase date. Remove and discard any packing
material before use.
Use the Drying Rack for items that you do not want to tumble
dry, such as sweaters and tennis shoes. When you use the
drying rack, the drum continues to turn, but the rack remains
stationary.
The drying rack is intended for use with the Timed Dry cycle
only. The drying rack cannot be used with Sensor cycles.
To use the drying rack:
IMPORTANT: Do not remove the lint screen.
1. Open dryer door.
3. Place wet items on top of the drying rack. Allow space
around items for air to circulate. The drying rack does not
move, but the drum will rotate; be sure to leave adequate
clearance between items and the inside of the dryer drum.
Make sure items do not hang over the edges or between
drying rack grille.
4. Close the door.
5. Select a Timed Dry/Air Only/Air Dry, or Low Temperature
cycle. Items containing foam, rubber, or plastic must be
dried on a clothesline or by using the Air Only setting
or Air Dry cycle, depending on model.
6. When the cycle is selected, the Estimated Time Remaining
display shows the default time. You can change the actual
time in the cycle by increasing or decreasing the cycle time.
7. Start the dryer.
NOTE: Check the lint screen and remove any lint accumulated
from items dried on the drying rack after the cycle is finished.
CYCLE STATUS INDICATORS
The Cycle Status Indicators show the progress of a cycle. Not all
indicators are available on all models.
Sensing
The Sensing indicator will light during Sensor Cycles to
indicate that the moisture sensor on the dryer is operating. This
indicator will not light during Timed Cycles or options such as
Wrinkle Prevent.
Check Vent
This indicator will show the status of airflow through the dryer
and the dryer vent system for the dryer’s life. During the sensing
phase at the beginning of the cycle, the Check Vent light will
come on if a blocked vent or low airflow issue is detected. This
light will stay on for the entire cycle. The light will be cleared
when selecting a new cycle, touching POWER, or opening the
door after the cycle has completed. This feature is available
during Sensor and Steam cycles only. For more information
on maintaining good airflow, see “Check Your Vent System for
Good Airflow”.
NOTE: If there are other error issues during a cycle, the Check
Vent indicator will not light up. See “Troubleshooting” section.
Good Airflow
This indicator will light if there is no major vent blockage.
Steaming
This indicator will light when a steam function is active.
NOTE: Steam is not available on all cycles.
Done
This will indicate that the selected cycle has ended and the load
may be removed from the dryer. If Wrinkle Prevent has been
selected, the dryer may continue to tumble the load, even if
the Done indicator is lit.
Check Lint Screen
The Check Lint Screen indicator will light when the drying
cycle is complete as a reminder to clean the lint screen.
Appearance may vary
13
DRYER CARE
CLEANING THE DRYER LOCATION
Keep dryer area clear and free from items that would block the
air flow for proper dryer operation. This includes clearing piles
of laundry in front of the dryer.
CLEANING THE DRYER INTERIOR
To clean dryer drum
1. Use a mild hand dish detergent mixed at a low
concentration with very warm water, and rub with
a soft cloth.
2. Rinse well with a wet sponge or towel.
3. Tumble a load of clean clothes or towels to dry drum
OR
Use a microfiber cloth and hot water in a spray bottle
to clean the drum and a second microfiber towel to dry.
NOTE: Garments that contain unstable dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the
rear of the dryer interior. These stains are not harmful to your
dryer and will not stain future loads of clothes. Dry unstable
dye items inside out to avoid transfer of dye.
REMOVING ACCUMULATED LINT
From Inside the Dryer Cabinet
Lint should be removed every 2 years, or more often,
depending on dryer usage. Cleaning should be done by a
qualified appliance servicer.
From the Exhaust Vent
Lint should be removed every 2 years, or more often,
depending on dryer usage.
CLEANING THE LINT SCREEN
Every load cleaning
The lint screen is located in the door opening of the dryer.
The control panel has an indicator light to remind you to clean
the lint screen after each load. A screen blocked by lint can
increase drying time.
To clean:
1. Pull the lint screen straight up. Roll lint off the screen with
your fingers. Do not rinse or wash screen to remove lint.
Wet lint is hard to remove.
2. Push the lint screen firmly back into place.
IMPORTANT:
n
Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
n
If lint falls off the screen into the dryer during removal,
check the exhaust hood and remove the lint. See “Venting
Requirements” in the Installation Instructions.
As needed cleaning
Laundry detergent and fabric softener residue can build up
on the lint screen. This buildup can cause longer drying times
for your clothes, or cause the dryer to stop before your load is
completely dry. The screen is probably clogged if lint falls off
while the screen is in the dryer.
Clean the lint screen with a nylon brush every 6 months,
or more frequently, if it becomes clogged due to a residue
buildup.
To wash:
1. Roll lint off the screen with your fingers.
2. Wet both sides of lint screen with hot water.
3. Wet a nylon brush with hot water and liquid detergent.
Scrub lint screen with the brush to remove residue buildup.
4. Rinse screen with hot water.
5. Thoroughly dry lint screen with a clean towel.
Reinstall screen in dryer.
14
SPECIAL INSTRUCTIONS
FOR STEAM MODELS
Water Inlet Hose
Replace inlet hose and hose screen after 5 years of use to
reduce the risk of hose failure. Periodically inspect and replace
inlet hose if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hose, record the date of
replacement.
To Winterize the Dryer
1. Unplug dryer or disconnect power.
2. Shut off water faucet.
3. Disconnect water inlet hose from faucet and drain.
To Use the Dryer Again
1. Flush water pipes. Reconnect water inlet hose to faucet.
Turn on water faucet.
2. Plug in dryer or reconnect power as described in the
Installation Instructions.
NON-USE, STORAGE, AND MOVING CARE
Install and store your dryer where it will not freeze. Because
some water may stay in the hose, freezing can damage your
dryer. If storing or moving your dryer during freezing weather,
winterize it.
Non-Use or Storage Care
Operate your dryer only when you are at home. If you will be
on vacation or not using your dryer for an extended period of
time, you should:
1. Unplug dryer or disconnect power.
2. Clean lint screen. See “Cleaning the Lint Screen.”
3. Turn off the water supply to the dryer. This helps to avoid
unintended flooding (due to a water pressure surge) while
you are away.
Moving Care
For power supply cord-connected dryers:
1. Unplug the power supply cord.
2. Gas models only: Close shut-off valve in gas supply line.
3. Gas models only: Disconnect gas supply line pipe and
remove fittings attached to dryer pipe.
4. Gas models only: Cap the open gas supply line.
5. Steam models only: Shut off water faucet.
6. Disconnect the water inlet hose from faucet, then drain the
hose. Transport hose separately.
7. Make sure leveling legs are secure in dryer base.
8. Use tape to secure dryer door.
For direct-wired dryers:
1. Disconnect power.
2. Disconnect wiring.
3. Steam models only: Shut off water faucet.
4. Steam models only: Disconnect the water inlet hose from
faucet; then drain the hose. Transport hose separately.
5. Make sure leveling legs are secure in dryer base.
6. Use tape to secure dryer door.
Reinstalling the Dryer
Follow the Installation Instructions to locate, level, and connect
the dryer.
DRYER CARE
15
First try the solutions suggested here or visit our website at www.maytag.com/product_help –
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
If you experience Possible Causes
Solution
Door not closed completely.
Make sure the dryer door is closed completely.
Touch and hold START/PAUSE 2–5 seconds.
Household fuse is blown or circuit
breaker has tripped.
There may be 2 household fuses or circuit breakers for the dryer.
Check that both fuses are intact and tight, or that both circuit
breakers have not tripped. Replace the fuses or reset the circuit
breaker. If the problem continues, call an electrician.
TROUBLESHOOTING
Dryer will not run
Humming or whining noise
with Steam cycle selected
(on some models)
Water pump or water inlet valve
(depending on model) on dryer
is running.
Unusual Noise
START/PAUSE not touched firmly or
held long enough.
Dryer Operation
Incorrect power supply. Electric dryers require 240-volt power supply. Check with a
qualified electrician.
Wrong type of fuse.
Use a time-delay fuse.
The water pump or water inlet valve on the dryer is used during the
Steam function. If the dryer has just been installed or unused for an
extended period, the pump or valve may be louder and run longer.
This is normal.
NOTE: The valve may make this noise even with no water line connected.
Thumping noise
Dryer hasn’t been used in a while.
This is due to temporary flat spots on the drum rollers.
The thumping sound will diminish after a few minutes.
Rattling or vibrating
noise
A small object caught between the
edges of dryer drum.
Check the front and rear edges of the drum for small objects. Clean
out pockets before laundering.
Dryer isn’t properly leveled.
The dryer may vibrate if not properly installed. See the Installation
Instructions. All four dryer feet should be in firm contact with the
floor.
Clothing is balled up in dryer. When balled up, the load will bounce, causing the dryer to vibrate.
Separate the load items and restart the dryer.
Dryer Results
Dryer will not heat Household fuse is blown or circuit
breaker has tripped.
The drum may be turning, but you may not have heat. Electric
dryers use 2 household fuses or circuit breakers. Replace the
fuses or reset the circuit breaker. If the problem continues, call
an electrician.
Clothes are not drying
satisfactorily or drying
times are too long
Lint screen is clogged with lint.
Clean lint screen before each load.
Run the dryer for 5–10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not feel air
movement or air movement is minimal, clean exhaust system of lint
or replace exhaust vent with heavy metal or flexible metal vent.
See the Installation Instructions.
The exhaust vent or outside exhaust
hood is clogged with lint, restricting
air movement.
Incorrect power supply.
Electric dryers require 240-volt power supply. Check with a
qualified electrician.
Supply line valve not open.
For gas dryers, make sure that the valve on the gas supply line
is open.
Clicking noise
Gas valve operating.
On gas dryers, you may hear the gas valve clicking as it opens and
closes. This is normal.
Energy Saver option is on.
For optimal drying times, turn off Energy Saver. For optimal energy,
turn on Energy Saver.
Loud humming or
increased noise during
cycle
Load is packed tightly or exhaust vent
is blocked.
Reduce load size to recommended load size in “Cycle Guide.”
Run the dryer for 5–10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not feel air
movement or air movement is minimal, clean exhaust system of lint
or replace exhaust vent with heavy metal or flexible metal vent.
See the Installation Instructions.
16
Possible Causes
Solution
Dryer Results (cont.)
The dryer is located in a room with
temperature below 45ºF (7ºC).
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
The dryer is located in a closet. Closet doors must have ventilation openings at the top
and bottom of the door. The front of the dryer requires a minimum
of 1" (25 mm) of airspace, and, for most installations, the rear of
the dryer requires 5" (127 mm). See the Installation Instructions.
Cycle time is too short
Steam models only: Clothes are
coming out of the Refresh cycle
with damp or wet spots.
Under certain environmental or installation conditions, you may
experience underdrying. Select the Timed Dry cycle, medium
drying temperature, for 5 to 10 minutes.
The Sensor Cycle is ending early. Change the dryness level setting on Sensor Cycles. Increasing
or decreasing the dryness level will change the amount of drying
time in a cycle. If loads are consistently ending too early, see also
“Changing the Sensor Cycle settings to increase drying time.”
Lint on load
Lint screen is clogged with lint.
Stains on load
Improper use of fabric softener.
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can
stain your garments. Do not use fabric softener sheets with
steam cycles.
Loads are wrinkled
The load was not removed from
dryer at the end of the cycle.
Steam models only: Select Refresh Cycle to tumble the load with
water and heat. This cycle is best for reducing wrinkles from loads
left in the dryer too long.
NOTE: Refer to garment care label instructions. Dry-clean-only
garments are not recommended.
The dryer was tightly packed. Dry smaller loads that can tumble freely.
Clothes are not drying
satisfactorily or drying
times are too long (cont.)
Steam models only: For steam
cycles, the water is not properly
connected with the dryer.
Make sure water is connected to the dryer. Check that water
inlet hose is connected to both the faucet and dryer’s water inlet
valve. Check that the water supply is turned on.
The load is too large and heavy
to dry quickly.
Fabric softener sheets are blocking
the grille.
The air outlet grille is just inside the door, behind the lint screen.
Check that it is not blocked by a fabric softener sheet.
Use only one fabric softener sheet, and use it only once.
Separate the load to tumble freely.
The load may not be contacting
the sensor strips on Sensor Cycles.
Level the dryer. See the Installation Instructions. All four dryer feet
should be in firm contact with the floor.
Clean lint screen before each load.
Stains on drum
Loose dyes in clothes.
Drum stains are caused by dyes in clothing (usually blue jeans).
These will not transfer to other clothing.
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.maytag.com/product_help –
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
If you experience
The Air Only temperature setting or
Air Dry cycle (depending on model)
has been selected.
Select the correct temperature for the types of garments being
dried. See “Cycle Guide.”
The exhaust vent is not the correct
length.
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. See the Installation
Instructions.
The exhaust vent diameter is not the
correct size.
Use 4" (102 mm) diameter vent material.
The dryer is not level.
Clothes not contacting the moisture sensors during Sensor cycles.
See “Level Dryer” in the Installation Instructions.
17
Possible Causes
Solution
The drying cycle has been
interrupted by a power failure.
Touch and hold START/PAUSE to restart the dryer. NOTE: The
Control Lock function may be enabled when recovering from a
power failure. To unlock the control, touch and hold CONTROL
LOCK for at least 3 seconds.
There may be a problem with your
home power supply, keeping the
dryer’s heater from turning on.
The dryer will continue to run when this diagnostic code is present.
Touch any setting or option name to clear the code from the
display and return to the estimated time remaining.
Try the following:
Check to see if a household fuse has blown or circuit breaker
has tripped. Electric dryers use two household fuses or breakers.
Replace the fuse or reset the circuit breaker.
Confirm that the power cord is properly installed. Refer to
the Installation Instructions for details.
Select a Timed Dry heated cycle, and restart the dryer.
If the message persists, consult a qualified electrician.
“L” or “L2” Diagnostic Code
(low or no line voltage
condition)
The lint screen or vent is clogged;
the vent is crushed or kinked or
has too many turns.
The dryer will continue to run when this diagnostic code is present.
Touch any setting or option name to clear the code from the
display and return to the estimated time remaining.
Try the following:
• Clean lint screen.
• Check to see if the vent run from the dryer to the wall is
crushed or kinked.
• Confirm that the vent run from the dryer to the wall is free
of lint and debris.
• Confirm that the exterior vent exhaust hood is free of lint
and debris.
• Confirm that your vent system falls within the recommended
run length and number of elbows for the type of vent you are
using. Refer to “Plan Vent System” in the Installaton Instructions
for details.
• Select a Timed Dry heated cycle, and restart the dryer.
• If the message persists, have your entire home venting run
cleaned.
Check Vent indicator is lit.
“PF” (power failure)
The dryer is in need of service. If a code beginning with an “F” appears in the display,
alternating between F# and E#, the dryer control has
detected a problem that requires service. Call for service.
Dryer Displaying Code Message or Cycle Status Indicator Lights Up
Dryer Results (cont.)
Load removed before cooldown
portion of cycle complete.
Allow the dryer to complete the cooldown portion of the cycle
before removing the load.
Load too hot
Using Timed Dry cycle with a high
temperature setting.
Select a Sensor cycle with a lower heat setting to avoid overdrying
the load.
Odors
Recent painting, staining, or
varnishing in the area where
your dryer is located.
Ventilate the area. When the odors or fumes are gone from the
area, rewash and dry the clothing.
Steam models only: For steam
cycles, the water is not properly
connected with the dryer.
Make sure water is connected to the dryer. Check that water inlet
hose is connected to both the faucet and dryer’s water inlet valve.
Check that the water supply is turned on.
Odors are left in garments after
wearing.
Steam models only: To remove odors left in garments after
wearing, select Refresh. The Refresh cycle is best for reducing
wrinkles from loads left in the dryer too long.
“F# E#” (F1 E1, F3 E1, etc.)
variable service codes
First try the solutions suggested here or visit our website at www.maytag.com/product_help –
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
If you experience
TROUBLESHOOTING
The Control Lock is enabled. Touch and hold CONTROL LOCK for 3 seconds to unlock
the controls of the dryer. During this time the LED Display
will count down 3-2-1. When the Control Lock is disabled,
the LED Display will clear.
“Loc” or “Lc”
18
MAYTAG
®
LAUNDRY
LIMITED WARRANTY
1. Commercial, non-residential, multiple-family use, or use inconsistent
with published user, operator, or installation instructions.
2. In-home instruction on how to use your product.
3. Service to correct improper product maintenance or installation,
installation not in accordance with electrical or plumbing codes, or
correction of household electrical or plumbing (i.e. house wiring,
fuses, or water inlet hoses).
4. Consumable parts (i.e. light bulbs, batteries, air or water filters, etc.).
5. Conversion of your product from natural gas or L.P. gas or reversal
of appliance doors.
6. Damage from accident, misuse, abuse, fire, floods, acts of God, or
use with products not approved by Maytag.
7. Repairs to parts or systems to correct product damage or defects
caused by unauthorized service, alteration, or modification of the
appliance.
8. Cosmetic damage including scratches, dents, chips, and other
damage to appliance finishes unless such damage results from
defects in materials and workmanship and is reported to Maytag
within 30 days.
9. Discoloration, rust, or oxidation of surfaces resulting from caustic
or corrosive environments, including but not limited to, high salt
concentrations, high moisture or humidity, or exposure to chemicals.
10. Pick-up or delivery. This product is intended for in-home repair.
11. Travel or transportation expenses for service in remote locations
where an authorized Maytag servicer is not available.
12. Removal or reinstallation of inaccessible appliances or built-in
fixtures (i.e. trim, decorative panels, flooring, cabinetry, islands,
countertops, drywall, etc.) that interfere with servicing, removal, or
replacement of the product.
13. Service or parts for appliances with original model/serial numbers
removed, altered, or not easily determined.
The cost of repair or replacement under these excluded
circumstances shall be borne by the customer.
ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS
REQUIRED TO OBTAIN WARRANTY SERVICE.
Please have the following information available when you call the
Customer eXperience Center:
n
Name, address, and telephone number
n
Model number and serial number
n
A clear, detailed description of the problem
n
Proof of purchase including dealer or retailer name and address
FIRST YEAR LIMITED WARRANTY (PARTS AND LABOR)
For one year from the date of purchase, when this major appliance
is installed, operated, and maintained according to instructions
attached to or furnished with the product, Maytag brand of
Whirlpool Corporation or Whirlpool Canada LP (hereafter
“Maytag”) will pay for factory specified parts and repair labor to
correct defects in materials or workmanship that existed when this
major appliance was purchased.
SECOND THROUGH TENTH YEAR LIMITED WARRANTY
(DRUM MOTOR AND STAINLESS STEEL BASKET ONLY -
LABOR NOT INCLUDED)
In the second through tenth years from the date of original
purchase, when this major appliance is installed, operated, and
maintained according to instructions attached to or furnished
with the product, Maytag will pay for factory specified parts for
the following components to correct non-cosmetic defects in
materials or workmanship in these parts that prevent function of
this major appliance and that existed when this major appliance
was purchased. This is a limited 10 year warranty on the below
named parts only and does not include repair labor.
n Drum (Side Walls Only)
n Drive Motor
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS
LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS
PROVIDED HEREIN. Service must be provided by a Maytag
designated service company. This limited warranty is valid only
in the United States or Canada and applies only when the major
appliance is used in the country in which it was purchased. This
limited warranty is effective from the date of original consumer
purchase. Proof of original purchase date is required to obtain
service under this limited warranty.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces
do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty
gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the
exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives
you specific legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Maytag makes no representations about the quality, durability, or need for service or repair of this major appliance other than the
representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes
with this major appliance, you should ask Maytag or your retailer about buying an extended warranty.
01/14
IF YOU NEED SERVICE:
1. Before contacting us to arrange service, please determine whether your product requires repair. Some
questions can be addressed without service. Please take a few minutes to review the Troubleshooting
or Problem Solver section of the Use and Care Guide, scan the QR code on the right to access
additional resources, or visit https://www.maytag.com/product_help.
2. All warranty service is provided exclusively by our authorized Maytag Service Providers.
In the U.S. and Canada, direct all requests for warranty service to:
Maytag Customer eXperience Center
In the U.S.A. call 1-800-688-9900. In Canada call 1-800-807-6777.
If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.
TEN YEAR LIMITED WARRANTY
WHAT IS COVERED
WHAT IS NOT COVERED
https://www.maytag.com/product_help
19
SÉCURITÉ DE LA SÉCHEUSE
20
IMPORTANT : Pour mettre l’ancienne sécheuse au rebut ou pour la remiser, enlever la porte.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Maytag MED7100DW Manuel utilisateur
- Catégorie
- Sèche-linge
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Maytag MED7100DW User manual
Documents connexes
-
Maytag MGD7100D Manuel utilisateur
-
-
Maytag MGDB955FC Manuel utilisateur
-
Maytag MGD4200BW Mode d'emploi
-
Maytag MED5500FC Manuel utilisateur
-
-
-
-
Maytag MED8630HW Guide de démarrage rapide
-