Serene Innovations CA-360Q Visual Alert System Manuel utilisateur

VISUAL ALERT SYSTEM

USER'S MANUAL

MODEL CA-360Q

06:30A 06:30P

pm

1

2

M

EN

TABLE OF CONTENTS

CA-360Q Features

Important Safety Instructions

General Description

Package Contents

Unit Overview

Display Details

Display Details Description

Installation

Landline Telephone Connection

Quick Self Test

Voice Announce Language Select

Set the Clock

Set Alarm Time

Direct Connect to an External Lamp Module CA-LX

Reset button

Special Note when running as Remote Receiver

Energy Saving Mode

Adding Extra Wireless Sensor Accessories

CA-AX Special Warning Message

View accessories registered

Set the Date

Ignore Select accessories

Clear All Accessories

System Menu

System Reset

6GEJPKECN5RGEKƒECVKQPU

Accessories for Sereonic Alert

FAQ

Warranty Service Information

FCC & IC Information

03

04

05

06

07

08

09

10

11

12

13

14

15

17

18

19

21

22

EN

03. www.sereneinnovations.com

2.4GHz Wireless Smart-Code Technology

- 360 full coverage of your entire home

Alarm clock

Baby's crying

Doorbell

Motion Sensor

Features:

Advanced Visual alert system alerts you to daily sounds:

Phone / cell

Weather alerts (external alarm)

Audio alarms

SOS paging and more

Loud speaker

Bright flasher

Bed shakers

Visual icons

Alerting accessory

Multiple alerting outputs:

Dual alarm settings (12/24-hr format)

Auto clock-dimming for a softer display at night

Dual bed shaker output jacks

Wireless Smart-Code technology supports thousands

of systems

Internal antenna design for long range operations

Analog phone jacks for landline telephone ringing

Output jack to control a 100 watt max. lamp module (optional)

Use 520 Hz square-wave technology for maximum audio alert

output

Built-in bright flashlight (with brightness control)

2-way SOS (help) paging

Simple installation – just plug and use

Battery back-up ( 4x AA NiMH)

AC adapter 110/240 VAC, 50/60 Hz operation

7 days full function battery back-up

Contemporary design with large 5” color display

User select color for icons and clocks

Intuitive alerting icons

User select show/hide main clock

Multiple language alert announces

Ignore accessories (in master mode Only)

Main power lost warning

Option to detect unregistered CA-AX audio sensors

Lost contact / Low battery warning on registered CA-AX sensors

EN

When using the Sereonic Alert Model CA-360Q, in order to reduce the

TKUMQHƒTGGNGEVTKECNUJQEMQTKPLWT[VQRGTUQPUDCUKEUCHGV[RTGECW-

tions should always be followed, including the following:

Read all instructions before using alliance.

Do not mount or place Master-Unit on a small surface.

Metal surfaces can reduce wireless signal transmission.

This product uses rechargeable batteries. Do not use non-

rechargeable batteries as charging of t his type can cause

battery leakage.

Always disconnect phone cord from wall jack before chang-

ing /installing batteries.

To reduce injury risk, close supervision is necessary when

appliance is used near children.

Do not contact moving parts or exposed metal surfaces.

Only use attachments recommended / sold by the manu-

facturer.

Do not use outdoors. Do not use near water.

To disconnect device, remove attached plugs from the

device.

Do not unplug the unit by pulling the cord – grasp plug, not

cord.

Unplug unit from outlet when not in use / before servicing

or cleaning.

Do not operate an appliance with a damaged cord or plug;

do not operate any appliance after it malfunctions, is

dropped or damaged in any manner. Return appliance to

nearest authorized facility for examination; repair or electri-

cal / mechanical adjustment.

Avoid using telephone products during electrical storms.

There's an electrical shock risk from lightning.

Do not use telephone to report a gas leak while in the

vicinity of the leak.

5RGEKƒECVKQPU QH VJKU RTQFWEV CTG UWDLGEV VQ EJCPIG

without notice.

Important Safety Instructions:

01.

02.

03.

04.

05.

06.

07.

08.

09.

10.

11.

12.

13.

14.

15.

EN

05. www.sereneinnovations.com

Model CA-360Q is an advanced wireless visual alert system for the

general public and special geared for the hard-of-hearing (HOH). It

has a dual-alarm clock with a 5 inch (diagonal) color graphics display,

and uses an exclusive Smart-Code technology and operates in the

2.4 GHz band. This technology offers a fast response and long range

operation. It can support thousands of systems without the need for

channel-setting switches.

The system alerts users to multiple different household

HWPEVKQPUGXGPVU WUKPI ƒXG  CNGTVKPI QWVRWVU URGCMGT HNCUJGT

bed-shaker, large visual icons, and digital voice speech. The display

icon shows the name of the alert activation (optional accessories

purchased separately).

&KHHGTGPVU[UVGOEQPƒIWTCVKQPUECPDGUGVWRQPVJG%#36JG

basic system setup can have only one (1) CA-360Q unit as the

master, and multiple remote receivers.

Additional wireless sensors, bed-shakers, and remote receivers may

DGRWTEJCUGFVQEQXGTCNCTIGJQOGQTQHƒEG0GYUGPUQTUOWUVDG

registered to the CA-360Q master-unit before they can be recognized

(See later “Adding Extra Wireless Sensor Accessories” section).

The CA-360Q, with its new system menu, provide the user options to

change some of the visual parameters, such as showing / hiding the

main clock, change clock colors, change icons color, change alerting

tones, and change voice speech language.

General Description:

EN

Package Contents:

Base Unit User’s Guide

Batteries AC Adapter Phone Cord

7PRCEMCPFTGOQXGKVGOUHTQOVJGDQZ%QPƒTOCNNKVGOUCTGKPENWF-

ed before disposing of the shipping box.

Items included are:

1 – Sereonic Alert CA360Q

1 – User's Guide

1 – Telephone Cable

1 – AC adapter

* Batteries (user provided)

EN

07. www.sereneinnovations.com

FRONT VIEW

BACK VIEW

Unit Overview:

SPK

SOS/PAIR RESET CLOCK

MODE

EN

3

4

2

1

Display Details:

5

8 7 6

10

9

EN

09. www.sereneinnovations.com

Display Detail Description

1Alarm-1 icon and set time.

2Detection of unregistered CA-AX audio transmitter icon

Press SPK+Alarm-2 buttons for 2 seconds to enable/disable.

When this function is disabled, the CA-360Q will only sound

alerts to its registered CA-AX audio transmitters. Default is

Off.

3Alarm-2 icon and set time.

4System mode icon - (M)aster or (S)ub (remote)

5Power and battery status icon

Show low battery status on registered CA-AX (audio sensor)

6Motion detect alerts enabled icon

Press “SPK”+“MODE” buttons for 2 seconds to enable/disable.

When function is disabled, the unit will not sound the alert on

registered CA-MX (motion sensor) is triggered. Default is Off.

7Bed shaker connection icon

The number 1 or 2 shows which bed shaker is connected.

Bed shaker-1 will shake when alarm-1 is on.

Bed shaker-2 will shake when alarm-2 is on.

Both shakers will shake when an accessory alert is received.

8Voice speech enable icon

Press MODE button for 3 seconds to change voice language.

9Speaker volume level – Off – Low – High

Press SPK button once to change the speaker volume

setting.

10 Main clock

Press CLOCK button for 2 seconds to show / hide the clock.

Press Alarm-2 button once to turn on/off the alarm

When turned on, use the (for hour) and (for minutes) to set

the alarm time while it is blinking. The time is set when

blinking stopped.

Press Alarm-1 button once to turn on/off the alarm.

When turned on, use the (for hour) and (for minutes) to set

the alarm time while it is blinking. The time is set when

blinking stopped.

EN

Installation:

Install four AA size rechargeable NiMH batteries in battery

compartment at bottom of unit.

Warning: Do not use regular batteries, as charging of this type

can cause batteries to leak and damage to the unit.

01.

Land Line Telephone Connection:

Connect an analog telephone to the PHONE OUT jack on the

back.

Connect a telephone cord to the LINE IN jack on the back of the

unit.

01.

02.

Place a call to the telephone number corresponding to the

connected telephone line.

Verify that all alerting outputs - display icon, flasher, ring tone,

and bed shaker (if connected) - respond correctly while the

telephone is ringing.

Verify that by answering the call (from any telephone), all alerting

outputs will stop.

03.

04.

05.

Plug AC adapter into outlet and connect the plug to the unit.

Connect bed shaker to SHAKER-1 output jack.

Press the SPK button to set the volume (speaker icon).

Verify the “M” indicator is shown. Default is master mode.

02.

03.

04.

05.

Note: The CA-360Q will operate without batteries, but installing

batteries is highly recommended to continue system operations

in case of a power outage.

Telephone

EN

11. www.sereneinnovations.com

Quick Self Test:

Press SOS button once on top of the unit. Verify that alert

outputs (speaker, voice, flasher, shaker and alert icon display)

lasts for about 45 seconds, then stops.

Press RESET button can stop at any time.

Verify that the flasher can be toggled ON and OFF using the

RESET button.

01.

02.

03.

Voice Announce Language Select

01.

02.

03.

Set Alarm Time :

Press Alarm-1 or Alarm-2 button once to enable the alarm.

The alarm icon and time will blink. Use the (for hour) and

(for minute) to change the alarm time if needed. The new alarm

time willbe set when it stops blinking.

When the alarm is on, the unit will sound and the connected

shaker will shake for 45-seconds, then stops for a 5 minute

snooze period.

This snooze pattern will repeat for up to one (1) hour. Press and

hold the RESET button for 2 seconds will stop further snoozes.

01.

02.

03.

Set The Clock:

01.

02.

03.

Note: SHAKER-1 and SHAKER-2 output jack corresponds to Alarm-1

and Alarm-2 individually, but BOTH jacks will be active during alerts.

Press the MODE button for about 3 seconds. The display will

show the available language list with the current language selec-

tion highlighted.

Use the or buttons to scroll and press MODE again to select.

If no voice speech is preferred, select Off from the list. The

speech icon with an “X” will be shown for no voice announce-

ments.

If there are remote receivers in the system, this new selected

language will be updated.

Press the (UP) button for 2 seconds to start.

Use the or buttons to select 12/24 format, then press MODE.

Use the button to change the hour, and the button to change

the minutes. The hours and minutes will continue to scroll when

you press the buttons.

2TGUU/1&'QT4'5'6DWVVQPYJGPƒPKUJGF%NQEMKUUGV

EN

During alarm clock , press once will stops alarm sounds and

starts a 5-minute snooze, or press for 2 seconds will stop further

snoozes.

In normal operations, press once will turn the flasher On / Off.

In battery mode, press once will turn display on for 3 seconds.

In menu setting, press once will exit the menu.

During alert alarms, press once will stop it, and reset all receiv-

ers.

Accessory low battery icon and warning message appeared:

press once will clear the message for 12 hours, and if press for

more than 6 seconds, the CA-360Q will temporary ignore the

condition until the next accessory check-in signal is received.

When CA-360Q operates as a remote receiver, it can ONLY paired to

a CA-360Q master unit, and cannot paired any accessories to itself.

While the CA-360Q is in remote receiver mode, some critical system

settings will be passed down from the master unit, and will not be

available to change. For normal operations, the user must perform a

system reset to convert the CA-360Q back to a master mode.

01.

02.

03.

04.

05.

06.

Sereonic Alert CA-360Q can control an external lamp via an optional

external lamp module (Model CA-LX, purchased separately).

User can control the lamp ON/OFF using the RESET button on top of

the unit. The operation of this lamp is synchronized with the flasher.

Connect to an External Lamp (Model CA-LX)

Press the Light Control button (rear) for about 6 seconds. The

display will be turned off and the unit will operate in battery mode

(with ac power attached). Press any button will cancel the mode.

All alerting functions are active during the energy saving mode.

Energy Saving Mode

RESET (Multi Function Button):

Note: The external lamp must be left in the ON position, and the lamp

must be incandescent type using less than 100 watts.

The RESET button behavior under different conditions:

Special Note when CA-360Q running as a Remote Receiver:

EN

13. www.sereneinnovations.com

Adding Extra Wireless Sensor Accessories

to the system:

01.

02.

03.

04.

05.

A new wireless sensor (example: a wireless doorbell) must be

learned (registered) into the CA-360Q unit before it can be recog-

nized.

Press and hold the SOS/PAIR button for 6 seconds until it beeps

and display “LEARN”, and the current accessories list.

Press and hold the new accessory's test button for about 6

seconds until the CA-360Q sounds, displayed the accessory

name , and then added to the accessory list.

While still in the learn mode, repeat step 3 above to learn another

accessory. Press the RESET DWVVQPVQGZKVYJGPƒPKUJGF

Test the new wireless accessory by pressing its test button. If

the CA-360Q sounds the alarms, the learning was successful. If

not, repeat the steps above and learn the accessory again.

Since the CA-AX (audio sensor) is primarily associate with detecting

GOGTIGPE[ UQWPFU GZCORNG ƒTG CNCTOU KV KU KORQTVCPV VJCV VJG

CA-360Q keeps constant monitoring with the registered CA-AX.

When the predetermined period has lapsed without receiving a signal

from the CA-AX, a low-battery icon with the AX number will appear,

and a warning message will be displayed. The message can only be

cleared by the Reset button, and will re-appear in 12-hours if the

alerting status has not been cleared.

Special Warning Message from CA-AX

CA-AX

CA-BX

CA-CX

CA-DB or CA-DX or CA-DXH

CA-MX

CA-NOAA

CA-PX

CA-RX

CA-SOS

Wireless Accessory

10

3

1

4 Any combination

3

1

10

4

Max Number Allowed

EN

Press the MODE button once will display all the accessories learned

(registered) with the CA360Q for about 5 seconds.

To view accessories registered

To Set The Date:

01.

02.

03.

04.

Ignore Select Accessories

Clear All Accessories

01.

02.

03.

This function only applies to CA-360Q in master mode.

Note: CA-360Q unit will not be alarmed by the ignored accessory,

but other remote receivers will be alerted by the accessory.

Note: This action clears all accessories registered in the CA-360Q unit

ONLY, and will not clear the memory from other remote receivers.

Option 1: (will not reset alarm time)

Press SOS / PAIR button for 6 seconds to enter the LEARN

mode.The display will show all the accessories registered.

Press the SOS/PAIR button 16 times in quick successions

to clear.

When successful, the display will show no accessories.

Press the RESET button to exit.

01.

02.

03.

04.

Option 2: (will reset alarm time to 12:00)

Perform a system reset function, see in the later section.

Press the (Down) button for 2 seconds to start.

Use the or buttons to select Year, then press MODE.

Use the or buttons to select Month, then press MODE.

Use the or buttons to select Day, then press MODE.

Press the CLOCK button once will show the date shortly at any

time.

Press and hold the SOS/PAIR button for 6 seconds until it beeps

and display “LEARN”, and the current accessories list.

Use or buttons to scroll and select the accessory you want

to ignore. Press and hold the SPK+ CLOCK buttons for 2

seconds, and the accessory name will be removed from the list.

Press the RESET DWVVQPVQGZKVYJGPƒPKUJGF

EN

15. www.sereneinnovations.com

SYSTEM MENU

Press SPK + Alarm-1 + buttons for 2 seconds to initiate

1

2

M

General CA-AX Alerts Enable / Disable

Note: Press RESET at any time will exit the menu

Note: The periodic check-in and low battery signals from these

non-registered CA-AX units will not be acknowledged by the

CA-360Q, so no warning messages will be generated.

1

a.

b.

When function is enabled, the unit will sound the alerts when ANY

audio transmitter (CA-AX) that is in range and has been activated.

SYSTEM

MENU

Press or button to scroll and highlight this icon

Press the MODE button to enable / disable the function. An

icon will show on the display when enabled.

EN

Icons Color

2

a.

b.

c.

d.

Clock Color

3

a.

b.

c.

d.

Voice Announce Language Select

4

a.

b.

c.

d.

Alert Tone Select

5

a.

b.

c.

d.

Exit Menu

6

a.

b.