Modern Forms PD-74045 Aretha Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
PD-74045
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
Plastic Anchor
Qty: 2pcs+1 Extra
Wood Screw
Qty: 2pcs+1 Extra
D
C
Wire Connector
Qty: 3pcs+1 Extra
Mounting Screw
Qty: 1 Extra
AB
2
INSTALLATION INSTRUCTIONS
PD-74045
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1. Shut o the power at the circuit breaker and remove existing xture,
including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area.
Be careful not to lose any small parts necessary for installation.
3. Remove the mounting screw (B) from the xture.
4. Adjust the xture wire length by pushing the cable gripper on the canopy and pulling
the wire as desired. Make sure the wires are the same length.
a. Retract these wires close to a desirable length to within the canopy before securing
the xture in place. Using the cable gripper to adjust more than 18” of wire length is
not desirable.
b. Warning: Shortening these cables without professional helps or electronic
background is not advisable. Any modications to the xture will result in voiding
the warranty of the product.
5. Drill holes in the wall aligned with the key holes located on the mounting back plate.
Insert the plastic anchor (D)
6. Secure the mounting back plate to the junction box using the screws provided with
the junction box. Fasten the mounting back plate to the wall with the plastic anchors using the wood screws (C) provided. Properly secure
the safety cord to the bracket on mounting back plate to temporary hang the xture in place.
(i)using any other non-original-manufacturer provided junction box screw may result in safty issue.
(ii) The side of the mounting plate marked “GND” must face out.
7. Connect the driver’s input wires to junction box wires as shown (Fig. 2). Make sure that all wire connectors (A) are secure. If your outlet
box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire
directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
8. Secure the xture to the mounting back plate using the mounting screw (B).
9. This xture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specic dimming
wires information.
10. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
11. To utilize 0-10V dimming: use wire purple (dim+), gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).
Make sure to connect 0-10V prior to power-up the xture in order to allow the 0-10V dimming to function properly.
White - Neutral
Black - Hot
Purple - Dim+
Grey - Dim-
Red - Fixture+
Black - Fixture-
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
13
4"13
8"
77
8"
113
4
"
41
8"
Junction Box
Driver
Wire Connector
White Wire
Black Wire
Bare Copper Ground Wire
Canopy
Mounting Screw
Junction Box Screw
A
B
Push up
Cable-gripper
Instruction:Adjust
the xture wire
length by pushing
the cable gripper on
the canopy and
pulling the wire as
desired.
Plastic Anchor
Wood Screw
Mounting Back
Plate
C
D
Safety Cords
Suspending line
(MAX 120")
Glass
(RPL-GLA-74045)
Fixture
-
1
-
2
Modern Forms PD-74045 Aretha Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms PD-73032 Bloom Mode d'emploi
-
-
-
-
-
-
-
-
-