IKEA AA-2196358-4 Manuel utilisateur

TRÅDFRI

max 5 cm

(max 2")

> 10 s

English 6

Français 18

Español 31

6English

ADD LIGHT SOURCES TO

YOUR STEERING DEVICE:

Before you can use your

light source you’ll need

to pair it with a steering

device.

To add more light

sources, just repeat the

steps below:

1. Make sure that your

light source is installed

and the main power

switch is turned on.

2. Hold the steering

device close to the

light source you want

to add (no more than 5

cm away).

7

3. Press and hold the

pairing button for at

least 10 seconds. A red

light will shine steadily

on the steering device.

Your light source will

begin to dim and

nally ash one time

to indicate that it has

been successfully

paired.

Up to 10 light sources

can be paired with 1

steering device.

Make sure to pair them

one at a time. If the light

sources are close to each

other, disconnect those

8

that have already been

paired from the main

power switch.

CAUTION:

DO NOT USE WITH

STANDARD DIMMERS.

Only use the control

provided with or

specied by these

instructions to control

this bulb. This bulb will

not operate properly

when connected to a

standard (incandescent)

dimmer or dimming

control. Only controllable

by IKEA Smart lighting

products.

9

The colour temperature

can be switched between

2200K (warm glow),

2700K (warm white) and

4000K (cool white).

RESET YOUR DEVICE

Toggle the main switch 6

times.

TECHNICAL DATA:

Operating frequency:

2405 – 2480 MHz

Output power: 10 dBm

10

Manufacturer:

IKEA of Sweden AB

Address:

Box 702, SE-343 81

Älmhult, SWEDEN

This device complies with

Part 15 of the FCC Rules.

This device contains

licence-exempt

transmitter(s)/receiver(s)

that comply with

Innovation Science and

Economic Development

Canada's licence-exempt

RSS standard(s).

Operation is subject

11

to the following two

conditions:

(1) this device may

not cause harmful

interference, and

(2) this device must

accept any

interference received,

including interference

that may cause

undesired operation

of the device.

WARNING:

Any changes or

modications to this unit

not expressly approved

by the party responsible

for compliance

12

could void the user’s

authority to operate the

equipment.

NOTE:

This equipment has been

tested and found to

comply with the limits for

a Class B digital device,

pursuant to part 15 of

the FCC Rules. These

limits are designed to

provide reasonable

protection against

harmful interference in a

residential installation.

This equipment

generates, uses and can

radiate radio frequency

13

energy and, if not

installed and used in

accordance with the

instructions, may cause

harmful interference to

radio communications.

However, there is

no guarantee that

interference will not

occur in a particular

installation. If this

equipment does cause

harmful interference

to radio or television

reception, which can be

determined by turning

the quipment o and on,

the user is encouraged

to try to correct the

interference by one or

14

more of the following

measures:

• Reorient or relocate the

receiving antenna.

• Increase the

separation between

the equipment and

receiver.

• Connect the equipment

into an outlet on a

circuit dierent from

that to which the

receiver is connected.

• Consult the dealer or

an experienced radio/

TV technician for help.

15

RF EXPOSURE

INFORMATION

According to RF exposure

regulations, under

normal operations the

end user shall refrain

from being closer than

20 cm from the device.

License rights and

limitations

NO RIGHTS OR LICENSES,

EXPRESS OR IMPLIED,

ARE GRANTED TO USE

THIRD-PARTY DEVICES

IN COMBINATION WITH

THESE PRODUCTS IN

A WIRELESS MESH

NETWORK, OR TO

16

USE THIRD-PARTY

SERVICES TO ACCESS,

MONITOR OR CONTROL

THESE PRODUCTS IN

A WIRELESS MESH

NEWORK VIA THE

INTERNET OR ANOTHER

EXTERNAL WIDE AREA

NETWORK.

For use pursuant to U.S.

Patent Nos.:

US 6,914,893

US 7,697,492

US 8,964,708

The crossed-out wheeled

bin symbol indicates

17

that the item should be

disposed of separately

from household waste.

The item should be

handed in for recycling

in accordance with

local environmental

regulations for waste

disposal. By separating

a marked item from

household waste, you

will help reduce the

volume of waste sent to

incinerators or land-

ll and minimize any

potential negative impact

on human health and

the environment. For

more information, please

contact your IKEA store.

18Français

AJOUT SOURCES

LUMINEUSES AU

DISPOSITIF DE

COMMANDE

Avant d’utiliser votre

source lumineuse, elle

doit être couplée avec un

dispositif de commande.

Pour ajouter d’autres

sources lumineuses,

il sut de répéter les

étapes ci-dessous :

1. S’assurer que la source

lumineuse est installée

et allumée.

2. Maintenir le dispositif

de commande à

proximité (pas plus

de 5 cm) de la source

19

lumineuse à ajouter.

3. Appuyer sur le bouton

de couplage et le

maintenir enfoncé au

moins 10 secondes.

Un voyant à LED

rouge s’allume de

manière continue

sur le dispositif de

commande. La source

lumineuse baissera en

intensité et clignotera

une fois pour indiquer

que le couplage est

réussi.

Il est possible de coupler

jusqu’à 10 sources

lumineuses à 1 dispositif

de commande.

20

Veiller à les coupler

l’une après l’autre. Si les

sources lumineuses sont

proches les unes des

autres, débrancher de

l’alimentation générale

celles qui ont déjà été

couplées.

MISE EN

GARDE :

NE PAS UTILISER AVEC

DES VARIATEURS

D'INTENSITÉ STANDARD.

Pour régler l'intensité

lumineuse de cette

ampoule, utiliser

uniquement le dispositif

La page est en cours de chargement...

IKEA AA-2196358-4 Manuel utilisateur

Ce manuel convient également à

IKEA AA-2196358-4 Manuel utilisateur

dans d''autres langues

Documents connexes