Mi-T-M HOM-SERIES Operating Instructions Manual

HOM-SERIES Hot Water Heater module Operator's Manual 1

OPERATING INSTRUCTIONS FOR

HOM-SERIES

HOT WATER HEATER MODULES

CAUTION

RISK OF INJURY!

READ MANUAL BEFORE OPERATING!

This manual is an important part of the

heater module and must

remain with the unit when you sell it!

2 HOM-SERIES Hot Water Heater module Operator's Manual

TABLE OF CONTENTS

INTRODUCTION ................................................................................................................................................3

IMPORTANT SAFETY WARNINGS ................................................................................................................4-9

RISK OF EXPLOSION OR FIRE .....................................................................................................4

RISK OF ASPHYXIATION ...............................................................................................................5

RISK OF ELECTROCUTION OR ELECTRICAL SHOCK ...............................................................6

RISK OF INJECTION OR SEVERE CUTTING INJURY .................................................................7

RISK OF BURNS .............................................................................................................................8

RISK OF BURSTING .......................................................................................................................8

RISK FROM MOVING PARTS ........................................................................................................8

RISK OF BODILY INJURY ..............................................................................................................9

INSTALLATION ...........................................................................................................................................10-13

LOCATION AND PLACEMENT .....................................................................................................10

ELECTRICAL .................................................................................................................................10

VENTILATION ............................................................................................................................... 11

WATER SUPPLY ...........................................................................................................................12

HIGH PRESSURE CONNECTION ................................................................................................12

PRE-OPERATION CHECKLIST ....................................................................................................13

PREPARATION ................................................................................................................................................14

ATTIRE ..........................................................................................................................................14

PRE-START SAFETY INSPECTION .............................................................................................14

OPERATING INSTRUCTIONS .........................................................................................................................16

FLUSHING THE SYSTEM ............................................................................................................16

HOT WATER OPERATION ............................................................................................................16

SHUTDOWN .................................................................................................................................16

MAINTENANCE ..........................................................................................................................................17-18

PREVENTIVE MAINTENANCE ....................................................................................................17

WINTERIZING ...............................................................................................................................17

MAINTENANCE CHARTS ..............................................................................................................................17

BURNER ADJUSTMENTS .............................................................................................................................18

TROUBLESHOOTING ................................................................................................................................19-20

STATEMENT OF WARRANTY .........................................................................................................................21

NATIONAL CODES:

ANSI Z223.1 (NFPA NO. 54) NATIONAL FUEL GAS CODE.

NFPA NO. 70 (NEC) NATIONAL ELECTRICAL CODE.

CSA B149.1 GAS INSTALLATION CODE.

CSA C22.1 CANADIAN ELECTRICAL CODE PART 1.

HOM-SERIES Hot Water Heater module Operator's Manual 3

INTRODUCTION

Congratulations on the purchase of your new HOM-SERIES Heater Module! You can be assured your heater module

was constructed and designed with quality and performance in mind. Each component has been rigorously tested to

ensure the highest level of acceptance.

This operator's manual was compiled for your benet. By reading and following the simple safety, installation, operation,

maintenance and troubleshooting steps described in this manual, you will receive years of trouble free operation from

your new heater module. The contents of this manual are based on the latest product information available at the time

of publication. The manufacturer reserves the right to make changes in price, color, materials, equipment, specications

or models at any time without notice.

! IMPORTANT !

These paragraphs are surrounded by a "SAFETY ALERT BOX." This box is used to designate

and emphasize Safety Warnings that must be followed when operating this heater module.

Accompanying the Safety Warnings are "signal words" which designate the degree or level

of hazard seriousness. The "signal words" used in this manual are as follows:

DANGER: Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided MAY

result in minor or moderate injury.

The symbols set to the left of this paragraph are "Safety Alert Symbols." These symbols

are used to call attention to items or procedures that could be dangerous to you or other

persons using this equipment.

ALWAYS PROVIDE A COPY OF THIS MANUAL TO ANYONE USING THIS EQUIPMENT. READ

ALL INSTRUCTIONS BEFORE OPERATING THIS HEATER MODULE AND ESPECIALLY POINT

OUT THE "SAFETY WARNINGS" TO PREVENT THE POSSIBILITY OF PERSONAL INJURY TO

THE OPERATOR.

Once the unit has been removed from the box, immediately write in the serial number of your unit in the space provided

below.

SERIAL NUMBER_________________________________

Inspect for signs of obvious or concealed freight damage. If damage does exist, le a claim with the transportation

company immediately. Be sure that all damaged parts are replaced and that the mechanical and electrical problems

are corrected prior to operation of the unit. If you require service, contact your customer service.

Please have the following information available for all service calls:

1. Model Number

2. Serial Number

3. Date and Place of Purchase

4 HOM-SERIES Hot Water Heater module Operator's Manual

POTENTIAL CONSEQUENCE PREVENTION

SAFETY WARNINGS

WARNING: When using this product, basic precautions should always be observed, including the following:

READ ALL SAFETY WARNINGS BEFORE INSTALLING AND USING HEATER MODULE

HAZARD

RISK OF

EXPLOSION OR FIRE

Serious injury or death may

occur from normal sparks in the

multiple ignition sources.

Never leave operating machine unattended.

Install the heater module where open ame or

torch is permitted.

Always operate heater module in a well

ventilated area free of ammable vapors,

combustible materials including dust or

gases.

Do not allow lint or dust to collect in burner

area.

Do not use this heater module to spray

ammable liquids! Flammable liquids can

create fumes which can ignite.

This heater module has multiple safety devic-

es which should never be altered, modied,

removed or made inoperative. If a device

fails, replace immediately with only genuine

manufacturer replacement part.

Serious injury or death may

occur if system safety's are not

properly maintained.

Serious injury or death may

occur from improper installation. Installation of this unit including all gas piping

must comply with all local, state and national

codes. (Standards to be followed include the

National Fuel Gas Code ANSI Z223.1/NFPA

No. 54. In Canada; Refer to the CSA B149.1

Gas Installation Code).

HOM-SERIES Hot Water Heater module Operator's Manual 5

POTENTIAL CONSEQUENCE PREVENTION

HAZARD

Serious injury or death may occur

from inhaling burner exhaust or

dangerous vapors.

Installation of this unit including the

ventilation of the combustion gases must

comply with all local, state and national

codes. (Standards to be followed include

the National Fuel Gas Code ANSI Z223.1/

NFPA No. 54. In Canada; Refer to the CSA

B149.1 Gas Installation Code).

Always make certain there is adequate

ventilation (fresh outside air) for breathing

and combustion. This will prevent the

buildup of dangerous carbon monoxide

gases. Beware of poorly ventilated areas,

or areas with exhaust fans which can

cause poor air exchange.

Follow all safety instructions provided with

the materials you are spraying. Use of a

respirator may be required when working

with some materials. Do not use this

heater module to dispense hazardous

materials.

RISK OF ASPHYXIATION

SAFETY WARNINGS

READ ALL SAFETY WARNINGS BEFORE INSTALLING AND USING HEATER MODULE

6 HOM-SERIES Hot Water Heater module Operator's Manual

POTENTIAL CONSEQUENCE PREVENTION

HAZARD

RISK OF

ELECTROCUTION

OR

ELECTRIC SHOCK

Serious injury or death could

occur if the heater module is not

properly grounded. Your heater

module is powered by electricity

and may cause electric shock or

electrocution if not used properly.

Installation of this unit including all

electrical connections must comply

with all local, state and national codes.

(Standards to be followed include NFPA

No. 70/NEC National Electrical Code.

In Canada; Refer to the CSA C22.1

Canadian Electrical Code Part 1)

This unit must be connected to a

grounded, permanent wiring system; or

an equipment-grounding conductor must

be run with the circuit conductors and

connected to the equipment-grounding

lead on the unit.

Make sure the heater module is

connected to a properly grounded source

which provides correct voltage and

adequate fuse protection. Disconnect

from power source when not in use or

when making repairs.

Never operate heater module with

electrical enclosures open, removed or

damaged.

Do not touch machine while standing in

water or with wet hands. Never let the

electrical supply or any connections lay

in the water.

DO NOT direct spray on or into electrical

installations of any kind! This includes

electrical outlets, light bulbs, fuse boxes,

transformers, the unit itself, etc.

DO NOT allow metal components of the

heater module to come in contact with

live electrical components.

Any electrical wiring or repairs performed

on this heater module should be done

by authorized service personnel in

accordance with local and national

electrical codes.

Before opening any electrical enclosure,

always shut off the heater module, relieve

pressure and disconnect the heater

module from the power source. Allow

heater module to cool down. Never

assume the heater module is safe to work

on just because it is not operating. It

could restart at any time!

Electrical shock may occur if heater

module is not operated properly.

Serious injury or death may occur

from contact with electricity.

Serious injury or death may occur if

electrical repairs are attempted by

unqualied persons.

Serious injury or death could result

from improper installation.

SAFETY WARNINGS

READ ALL SAFETY WARNINGS BEFORE INSTALLING AND USING HEATER MODULE

HOM-SERIES Hot Water Heater module Operator's Manual 7

Serious injury or death could

occur from high pressure spray

penetrating the skin.

Keep clear of nozzle and spray! Never put

your hand, ngers or body directly over the

spray nozzle.

Never point the high pressure discharge

stream at persons.

This equipment is to be used only by

trained operators.

Always keep operating area clear of all

persons.

To reduce the risk of injury, close

supervision is necessary when using this

equipment near children. DO NOT allow

children to operate this unit.

SEEK EMERGENCY MEDICAL CARE if

the spray appears to have penetrated the

skin! DO NOT TREAT AS A SIMPLE CUT!

Be prepared to tell a physician exactly what

kind of cleaning agents you were using

by reading the Material Safety Data Sheet

(MSDS) provided with your detergent.

High pressure hoses should be inspected

daily for signs of wear. If evidence of

failure exists, promptly replace all suspect

hoses to prevent the possibility of injury

from the high pressure spray. If a hose or

tting is leaking, NEVER PLACE YOUR

HAND DIRECTLY ON THE LEAK.

Before using heater module, or when quick

connecting high pressure hoses and spray

nozzles, be certain the "collar" on the

female quick connect is locked securely to

prevent accidental discharge and that all

quick coupler ttings are secure.

NEVER operate the gun with the trigger

wired in the open position. To prevent

accidental discharge, the trigger gun

should be securely locked when not in use.

Before removing the spray nozzle or

servicing the unit, ALWAYS shut off the

unit and trigger the gun to release trapped

pressure. (Even after you shut off the

unit, there is high pressure water left in the

pump, hose and gun until you release it by

triggering the gun.)

POTENTIAL CONSEQUENCE PREVENTION

HAZARD

SAFETY WARNINGS

READ ALL SAFETY WARNINGS BEFORE INSTALLING AND USING HEATER MODULE

RISK OF INJECTION

OR

SEVERE CUTTING INJURY

8 HOM-SERIES Hot Water Heater module Operator's Manual

RISK OF BURNS

RISK OF BURSTING

RISK FROM MOVING PARTS

Serious injury may occur from

touching the heat exchanger or

vent piping. These areas can

remain hot for some time after the

heater module is shutdown.

Never exceed manufacturers maximum

allowable pressure rating of attachments.

Do not allow any hoses to make contact

with the heat exchanger to prevent the

possibility of bursting. Avoid dragging the

hoses over abrasive surfaces such as

cement.

Use only manufacturer recommended

repair parts for your heater module.

In freezing temperatures, the unit must

always be warm enough to ensure there

is no ice formation in the unit. Do not

start the heater module without rst

allowing the unit to thaw.

Never allow any part of your body to

contact the heat exchanger or the vent

piping.

POTENTIAL CONSEQUENCE PREVENTION

HAZARD

Serious injury may occur to the

operator from moving parts on the

heater module.

Do not operate the unit without all

protective covers in place or make any

adjustments without shutting off the

heater module, relieving pressure and

disconnecting the heater module from

the power source. Allow heater module

to cool down. Never assume the heater

module is safe to work on just because

it is not operating. It could restart at any

time!

Serious injury may occur from a

heater module malfunction or

exploding accessories if in-

correct system components,

attachments or accessories are

used.

Serious injury or death may occur if

attempting to start the heater mod-

ule when the unit is frozen.

SAFETY WARNINGS

READ ALL SAFETY WARNINGS BEFORE INSTALLING AND USING HEATER MODULE

HOM-SERIES Hot Water Heater module Operator's Manual 9

RISK OF BODILY INJURY

Serious injury or death may occur

from detergents contacting or

penetrating the skin.

SEEK EMERGENCY MEDICAL CARE if

the spray appears to have penetrated the

skin! DO NOT TREAT AS A SIMPLE CUT!

Be prepared to tell a physician exactly what

kind of cleaning agents you were using

by reading the Material Safety Data Sheet

(MSDS) provided with your detergent.

Never use any solvents or highly corrosive

detergents or acid type cleaners with this

heater module.

Protective equipment such as rubber suits,

gloves and respirators are advisable,

especially when using cleaning detergents.

Keep all detergents out of the reach of

children!

ALWAYS wear protective goggles when

operating the unit to shield the eyes from

ying debris and detergents.

DO NOT direct spray toward fragile

materials such as glass for shattering could

occur.

Stay alert-watch what you are doing. Do

not operate the unit when fatigued or under

the inuence of alcohol or drugs.

NEVER squeeze the trigger unless

securely braced.

DO NOT overreach or stand on unstable

support.

Wet surfaces can be slippery, wear

protective foot gear and keep good footing

and balance at all times.

NEVER trigger the gun while on a ladder

or roof.

ALWAYS hold on rmly to the gun/lance

assembly when starting and operating the

unit. Failure to do so can cause the lance

to fall and whip dangerously.

Know how to stop the heater module and

bleed pressures quickly. Be thoroughly

familiar with controls.

DO NOT leave pressurized unit

unattended. Shut off the heater module

and release trapped pressure before

leaving.

DO NOT operate the unit if you see any

oil or water leaks from the machine. DO

NOT resume operation until the unit has

been inspected and repaired by a qualied

serviceman.

Never make adjustments on the machine

while in operation.

Before servicing the unit: shut off the

heater module, relieve pressure and

disconnect the heater module from the

power source. Allow heater module to cool

down. Never assume the heater module

is safe to work on just because it is not

operating. It could restart at any time!

POTENTIAL CONSEQUENCE PREVENTION

HAZARD

Serious injury can occur from

loose debris being propelled at a

high speed from the spray gun.

Injury may occur if the operator

loses his balance caused by the

thrust of water traveling through

the spray nozzle.

Injury may occur from the heater

module.

SAFETY WARNINGS

READ ALL SAFETY WARNINGS BEFORE INSTALLING AND USING HEATER MODULE

SAVE THESE INSTRUCTIONS

10 HOM-SERIES Hot Water Heater module Operator's Manual

1. This unit should be installed indoors by a qualied serviceman in a non-

freezing, dry environment away from damaging winds and rain. If any part of

the unit becomes frozen, excessive pressure may build up in the unit which

could cause it to burst resulting in possible serious injury to the operator or

bystanders. Normal precautions should be taken so that excess moisture

does not reach the electrical controls or the power unit.

2. It should be placed in an area away from ammable or combustible material.

These types of material should be kept at least 20 feet away from the

unit.

3. Avoid small areas and exhaust fans. Combustion becomes difcult and

carbon monoxide may result in these areas. Allow enough space for servicing.

Some codes will require certain distances from walls and ooring. Two feet

away from the walls should sufce.

4. This unit should only be placed on a level surface. NEVER spray water

directly on the unit.

5. DO NOT place unit in an area:

a. where ammable gas vapors may be present.

b. with insufcient ventilation.

c. where there is evidence of oil or fuel leaks.

RISK OF EXPLOSION OR FIRE!

DO NOT PLACE UNIT IN AN

AREA WHERE FLAMMABLE

GAS VAPORS MAY BE PRESENT.

A SPARK COULD CAUSE AN

EXPLOSION OR FIRE!

RISK OF UNIT BURSTING!

DO NOT LOCATE THE UNIT IN

FREEZING ENVIRONMENTS!

RISK OF ASPHYXIATION!

USE THIS PRODUCT ONLY IN

WELL VENTILATED AREAS! THE

EXHAUST CONTAINS CARBON

MONOXIDE, A POISONOUS,

ODORLESS AND INVISIBLE

GAS. BREATHING THIS GAS

CAN CAUSE SERIOUS INJURY,

ILLNESS & POSSIBLE DEATH.

INSTALLATION

ELECTRICAL:

1. Installation of this unit should be performed by a qualied serviceman and

all electrical installation must conform to all local, state and national codes,

including NFPA No. 70 (NEC) National Electrical Code. In Canada; Refer

to the CSA C22.1 Canadian Electrical Code Part 1.

2. Ensure electrical supply is identical to the specications listed on the heater

module data plate.

3. Ensure all connections are secure and covers are replaced.

LOCATION AND PLACEMENT:

RISK OF ELECTROCUTION!

THIS UNIT MUST BE CONNECTED

TO A PROPERLY GROUNDED

OUTLET.

DANGER

WARNING

HOM-SERIES Hot Water Heater module Operator's Manual 11

INSTALLATION

VENTILATION:

1. Installation of this unit in an indoor or in an enclosed area should be performed

by a qualied serviceman and all venting must conform to all local, state and

national codes, including the National Fuel Gas Code ANSI Z223.1/NFPA

No. 54. In Canada; Refer to the CSA B149.1 Gas Installation Code. The

burner exhaust should be stacked to the outside atmosphere and a draft

diverter should be installed as well.

NOTE: There should be no more than 6500 BTU per square inch of ue.

2. A draft diverter must be installed above the exhaust outlet. This diverter

breaks the chimney effect and enhances the draft through the burner for a

more efcient ame. It also helps prevent cold air down drafts from freezing

the heat exchanger.

3. Install the recommended ue pipe per local, state and national codes,

including the National Fuel Gas Code ANSI Z223.1/NFPA No. 54. In Canada;

Refer to the CSA B149.1 Gas Installation Code. If the ue pipe exceeds 10

feet in length or contains more than two elbows, the natural draft may be

eliminated and the burner will not ignite. DO NOT install a movable ue

pipe damper.

4. If the unit is being installed in an enclosed room, provide adequate air for

combustion by installing openings to the room near the ceiling for ventilation

and near the oor for burner combustion. These openings should be sized

using one square inch for each 1000 BTU per inch of the machine.

Example: A heater module with a 400,000 BTU input requires openings of 400

square inch or approximately 3 feet x 1 foot.

5. If the building in which the unit is being installed seems unusually tightly

constructed, it is recommended that air intakes extending to the outside of the

building be employed to supply combustion air. End the intakes outside the

building with a downward opening to protect these intakes from snow and/or

rain. Include a mesh screen no smaller than 1/4" over the opening.

DRAFT DIVERTER

ENCLOSED ROOM VENTILATION

12 HOM-SERIES Hot Water Heater module Operator's Manual

INSTALLATION

WATER SUPPLY:

1. Using the quick connect at the inlet of the unit, connect the water supply

to the unit. For best results, the input to the unit should be 3-6 GPM.

NOTE: Incoming water pressure must not exceed 3500 PSI.

2. Connect the discharge hose provided to the outlet of the unit.

3. Connect gun/wand/lance assembly to the discharge hose.

4. Make sure all connections are secured before start-up.

HIGH PRESSURE HOSE CONNECTION

QUICK CONNECT

HOSE CONNECTION

HIGH PRESSURE CONNECTION:

Connect the high pressure discharge hose by connecting one end to the

heater module and the other end to the gun assembly. Make certain the

quick connects are securely locked together.

HOM-SERIES Hot Water Heater module Operator's Manual 13

INSTALLATION

QUESTIONS

CODES:

1. Does the electrical supply meet respected codes?

2. Does the ventilation system meet respected codes?

LOCATION:

1. Is the unit installed indoors on a level surface in a dry area

protected from excessive wind, rain and moisture?

2. Is the unit located away from ammable and combustible

material?

3. Is the unit located in a large enough area for adequate air ow?

ELECTRICAL:

1. Is the unit properly grounded?

2. Do all electrical components used meet requirements shown

on the unit I.D. Plate and is the voltage correct?

VENTILATION:

1. Are the correct ue pipe and draft hood sizes employed?

2. Is there adequate ventilation for burner combustion?

3. Is the unit properly vented to allow adequate air ow?

4. Is exhaust stacked to outside atmosphere?

GENERAL:

1. Have all operators using this unit read the Installation and

Operator's Manual and understood all safety warnings?

2. Has the unit been installed by qualied service people who

followed the Installation and Operator's Manual instructions?

3. Is there ample water supply?

YES NO

PRE-OPERATION CHECKLIST:

Before starting the unit, answer the questions in this checklist:

IF NO WAS MARKED FOR ANY OF THESE QUESTIONS, CORRECT THE SITUATION BEFORE

OPERATING THIS UNIT.

14 HOM-SERIES Hot Water Heater module Operator's Manual

1. Before starting the unit, perform the following procedures:

a. Check all hose connections to ensure they are securely tightened.

b. Inspect for system water and oil leaks.

c. Check to ensure the voltage is on.

d. Inspect high pressure hoses for kinking, cuts and leaks. If a cut or leak

is found, DO NOT USE HOSE! Replace hose before starting unit. See

"Risk of Injection" warnings, pg. 7. Be sure that all damaged parts are

replaced and that the mechanical problems are corrected prior to opera-

tion of the unit. If you require service, contact your Customer Service

Representative.

PRE-START INSPECTION PROCEDURES:

PREPARATION

ATTIRE:

Proper attire is essential to your safety. It is advised to utilize whatever means

necessary to protect eyes, ears, and skin. Additional safety attire (such as

respiratory mask) may be required when using detergent cleaning agents with

this heater module.

HOM-SERIES Hot Water Heater module Operator's Manual 15

WARNING

THE FOLLOWING PAGES CONTAIN OPERATING AND

MAINTENANCE INSTRUCTIONS.

DO NOT ATTEMPT TO OPERATE THIS HEATER MODULE

UNTIL YOU HAVE READ AND UNDERSTOOD ALL

SAFETY PRECAUTIONS AND INSTRUCTIONS

LISTED IN THIS MANUAL. FOLLOW THE MAINTENANCE

INSTRUCTIONS SPECIFIED IN THE MANUAL.

INCORRECT OPERATION OF THIS UNIT CAN CAUSE

SERIOUS INJURY!!

DO NOT ALTER OR MODIFY THIS EQUIPMENT

IN ANY MANNER!

16 HOM-SERIES Hot Water Heater module Operator's Manual

SHUTDOWN:

1. If the burner switch is still on, turn it off.

2. Squeeze the trigger and discharge the water for a period of three minutes

to cool the heat exchanger and high pressure hose. (Insufcient cool down

period of the high pressure hose will cause excessive wear and eventual

rupturing of the hose.)

3. Turn off the water supply to the heater module.

4. Trigger the gun momentarily to relieve trapped pressure.

RISK OF BURN!

THE WATER TEMPERATURE

COULD BECOME VERY

HOT DURING HOT WATER

OPERATION. BE CAUTIOUS

WHEN ADJUSTING PRESSURE

OR CONTROLLING THE TRIGGER

GUN/LANCE ASSEMBLY.

WHEN COLD WATER IS BEING

PUMPED INTO THE HEAT

EXCHANGER AND THE BURNER

IS ON, CONDENSATION MAY FORM

ON THE COIL AND DRIP. THIS

WILL GIVE THE APPEARANCE OF

A LEAKING COIL PARTICULARLY

IN COLD HUMID WEATHER.

IMPORTANT

WARNING

OPERATING INSTRUCTIONS

Once your unit has been installed by a qualied serviceman and you have

completed the PRE-OPERATION CHECKLIST on pg. 13, you are ready for

operation. The following steps will help you operate your machine safely.

FLUSHING THE SYSTEM:

1. This unit has a steel coil which, after setting, will cause the water remaining

in the coil from the previous usage to turn brown or black. This water must

be ushed from the system before start-up. This procedure should be

performed without a gun and lance installed.

a. Attach garden hose to machine.

b. Turn on water supply.

c. Run the water for 3-5 minutes.

d. Turn off water supply when clear water is discharged from coil.

HOT WATER OPERATION:

1. Push in the burner switch to turn on the burner. On initial start-up, water

will begin turning hot in approximately 60 seconds and will reach maximum

temperature in approximately 3 minutes, provided the trigger remains

squeezed. The burner will stop ring when the trigger is released.

2. Set thermostat to the desired setting.

At this point, the unit is operating as a hot water heater module. Be certain to

be extremely cautious when adjusting the pressure and controlling the trigger

gun/lance assembly to avoid the possibility of burns.

RISK OF UNIT DAMAGE!

BE CERTAIN THE GUN &

LANCE ASSEMBLY ARE

NOT CONNECTED TO THE

UNIT WHILE FLUSHING THE

SYSTEM. FLUSHING ALLOWS

MINERAL DEPOSITS TO BE

RELEASED FROM THE SYSTEM

WHICH WOULD OBSTRUCT

OR DAMAGE THE GUN AND

NOZZLE ASSEMBLY RESULTING

IN COSTLY REPAIRS.

CAUTION

HOM-SERIES Hot Water Heater module Operator's Manual 17

PREVENTIVE MAINTENANCE:

LEAKS: Promptly eliminate any leaks found in the pumping system by

removing suspect parts, applying thread sealant to the threads and

reinstalling.

NOTE: If using teon tape, be certain no tape gets inside any plumbing to

prevent the possibility of a plugged spray nozzle.

QUICK COUPLERS: There are o-ring seals inside the couplers which will

deteriorate. To replace, simply install a replacement o-ring to correct

the leak. (Additional o-rings can be purchased from your dealer.)

NOZZLE: Water ow through the spray nozzle will erode the orice,

making it larger, resulting in a pressure loss. Nozzles should be

replaced whenever pressure is less than 85% of the maximum. The

frequency of replacement will depend upon such variables as mineral

content in the water and number of hours the nozzle is used.

MAINTENANCE

32˚F 0˚C

WINTERIZING:

For storage and transportation purposes in subfreezing ambient temperatures,

it will be necessary to winterize this unit. This unit must be protected to the

lowest incurred temperature for the following reasons:

1. If any part of the water handling system becomes frozen;

excessive pressure may build up in the unit which could cause the

unit to burst resulting in possible serious injury to the operator or

bystanders.

2. The water handling system in this unit may be permanently

damaged if frozen. FREEZE DAMAGE IS NOT COVERED BY

WARRANTY.

If you must store your unit in an area where the temperature may fall below

32°F, you can protect your unit by following the procedure outlined below.

AIR BLOW OUT:

1. Remove the nozzle from the wand assembly. Squeeze the trigger

until water ceases to exit the wand assembly.

2. Connect an air tting from an air hose to the heater module inlet.

3. Run compressed air into the system to remove all water from the

system.

RISK OF UNIT BURSTING.

DO NOT STORE / OPERATE

UNIT IN A FREEZING

ENVIRONMENT!

WARNING

QUICK COUPLERS

PREVENTIVE OPERATOR MAINTENANCE CHART

DEALER MAINTENANCE CHART

PROCEDURE DAILY

Fuel inspection X

Water leak inspection X

Quick-connect and hose inspection X

PROCEDURE 12 MONTHS

Inspect fuel pump internal lter X

Check burner electrodes X

Burner inspection X

Exhaust ventilation inspection X

*Descale coil X

*Scale buildup will vary with mineral content in the water and amount off us-

age. Descaling can range from monthly to yearly maintenance.

18 HOM-SERIES Hot Water Heater module Operator's Manual

MAINTENANCE

FUEL FILTER/WATER SEPARATOR:

Inspect bowl on fuel lter/water separator for water accumulation. If water exists,

unscrew drain valve on bowl to drain water, then close.

BURNER AIR ADJUSTMENT:

The air shutter has been factory preset for proper operation between sea level

and 2000 feet elevation at standard conditions (60°F ambient water and air tem-

peratures). In colder temperatures or higher altitudes, it may be necessary to

adjust the air supply to the combustion chamber. This adjustment will maximize

burner efciency and avoid inefcient operation or excessive sooting of the heat

exchanger coil. A smoke spot test is recommended during any air shutter and

band adjustment. If you do not have the equipment to perform a smoke spot

test, follow the procedures listed below.

1. The machine must be running and the burner ON.

2. Loosen the Locking Screw (#3) on the shutter.

3. Check for smoke from the heat exchanger exhaust. If smoke is

not present, slowly close the Air Shutter (#1) by moving the dial

counterclockwise to a lower number. Continue moving the dial until

smoke appears.

4. Record this setting.

5. Open Air Shutter (#1) two increments. Example: If Air Shutter was

set at 2, move it to 4.

6. Slowly trigger the gun on and off. This will cause the burner to turn

on and off. Look for a smoke puff when the burner ignites.

7. Repeat steps 5 and 6 until a smoke puff is noticed. Record the Air

Shutter Setting.

8. The difference between the recorded settings in steps 4 and 7 is the

combustion window. Set the dial 1/2 way between these settings.

NOTE: If you are unable to detect a setting on either step 3 or 7, more or less

air may be needed to achieve a proper combustion window. Loosen the

Bolt (#4 at left) and open the Air Band (#2) in 1/4" increments. Repeat

steps 3-8 until proper combustion window is achieved.

BURNER AIR ADJUSTMENT

HOM-SERIES Hot Water Heater module Operator's Manual 19

SYMPTOM PROBABLE CAUSE REMEDY

TROUBLESHOOTING

Water is leaking under heat Condensation. May occur in cool, humid conditions.

exchanger coil.

Ruptured heat exchanger coil. Replace.

Burner will not ignite Switch is defective. Check switch position or replace.

Adjustable Thermostat is defective Check switch position or replace.

or in the "Off" position.

No voltage. Contact Customer Service.

Out of fuel. Refuel.

Fuel tank inlet tube screen obstructed. Remove, clean or replace tube.

Trigger gun is closed. Open trigger gun for pressure.

Fuel pickup screen is obstructed. Remove, clean or replace.

Temperature above thermostat Unit will automatically reignite when

setting. cool.

Flexible coupler broken. Replace.

Dirty or clogged fuel lter. Drain or replace as necessary.

Fuel pump sucking air. Tighten all fuel intake connections.

Eliminate leaks in intake line.

Fuel pump inoperative. Check pressure, replace if needed.

(Pressure should be checked by an

authorized service technician.)

Dirty or clogged fuel nozzle. Replace.

Improper burner air adjustment. Adjust as explained on page 18.

Ignition transformer failure. Replace.

Ignition electrodes not set properly, Contact Customer Service.

damaged or worn.

Fuel solenoid valve failure. Replace.

High PSI mode. Verify burner switch is in the

"ON" position.

20 HOM-SERIES Hot Water Heater module Operator's Manual

Burner motor will not run. Switch is defective position. Check switch position or replace.

No voltage. Contact Customer Service.

Motor overload. Reset when cool.

Fuel pump seized. Allow motor to cool. Repair or

replace.

Burner runs erratically. Water in the fuel oil. Drain fuel lter/water separator.

Drain fuel tank, and replace with

clean fuel.

Dirty fuel lter/water separator. Replace element.

Fuel pickup screen is obstructed. Contact Customer Service.

Dirty fuel nozzle. Replace.

Improper air adjustment setting. Adjust as explained on page 18.

Fuel pump malfunctioning. Replace.

Burner runs, but will not heat. Low fuel pump pressure. Check fuel pump pressure, adjust or

replace if needed. (Pressure should

be checked by an authorized

service technician.)

Dirty fuel nozzle. Replace.

Improper air adjustment setting. Adjust as explained on page 18.

Burner discharges white smoke. Low on fuel. Refuel. If white smoke persists,

contact Customer Service.

Low fuel pressure. Check fuel pump pressure, adjust or

replace if needed. (Pressure should

be checked by an authorized

service technician.)

Fuel pickup screen is obstructed. Contact Customer Service.

Dirty fuel nozzle. Replace.

Improper air adjustment setting. Adjust as explained on page 18.

Cold combustion chamber start-up. Run burner for several minutes.

Excessive air supply. Adjust as explained on page18.

Burner discharges black smoke. Insufcient air supply. Adjust as explained on page 18.

Fuel nozzle orice is too large. Replace with correct nozzle.

Fuel pressure is too high. Contact Customer Service.

Combustion chamber loaded with Contact Customer Service.

unburned fuel.

SYMPTOM PROBABLE CAUSE REMEDY

TROUBLESHOOTING

La page est en cours de chargement...

Mi-T-M HOM-SERIES Operating Instructions Manual

Mi-T-M HOM-SERIES Operating Instructions Manual

dans d''autres langues

Documents connexes

Autres documents