Netatmo Smart thermostat Manuel utilisateur

Marque: Netatmo

Modèle: Smart thermostat

Taper: Manuel utilisateur

Replacing a wall-mounted thermostat

You can watch this installation at:

http://netatmo.com/video1

• Read these instructions carefully before starting the installation.

• The Netatmo Thermostat must be installed according to

applicable standards.

• Before any intervention, make sure power is turned off.

• The Netatmo Thermostat cannot control electric converters.

Warning!

In the box

Color Adhesives

Power Plug

Thermostat Relay (Boiler adapter)*

(Mobile stand)*

* not used in this setup

Mounting Plate

Trim plate

3 AAA batteries 4 screws

4 screw anchors

(Tape)*

Relay

Plug the Power Plug

into the Relay.

Plug the Relay into a wall

socket in the same room

as your existing thermostat.

The Relay will blink white.

Switch o the power supply.

Identify

Remove the cover of your old

thermostat.

Take a picture of the wiring.

Power supply wires

Usually blue and

brown wires

Control wires

Usually black

or grey wires

- If there are only two wires, they are the

control wires and are useful in this setup.

- If there are more than two wires,

identify

the two control wires. They are usually

black or grey.

The wires can be identiﬁed as shown on

the following diagram

Note: If there are more than two wires, the

others are power supply wires and are

useless here. They are usually brown, blue,

green or yellow.

In doubt, please send a picture to

[email protected]

and our support team

will help you identify the right wires

P / N

L / N

COM / NO

Replace

Disconnect your old thermostat.

Remove it from the wall.

Pass the wires through the Netatmo

mounting plate and screw the latter to the

wall.To hide potential scratches and holes

left behind, use the trim plate.

Screw the control wires previously identiﬁed

into the electrical terminals and insulate the

unused wires.

Place and screw the protection cover onto

the electrical terminals.

Customisation

You can choose to customize your

Thermostat by using one of the colour

adhesives.

Take o the outer frame of the adhesive.

Stick it on the back of your Thermostat.

Insert the batteries in the Thermostat.

Set the Thermostat on the mounting plate.

Switch the power supply back on.

Thermostat

The Thermostat will display the start screen

and search for the Relay.

If the Thermostat has found the

Relay, it displays the desired

temperature and the room

temperature.

If the Thermostat hasn’t found the

Relay, it displays the «!» symbol.

In this case, move the relay closer to

the Thermostat and wait until the «!»

symbol disappears.

Thermostat

Measured temperature

Desired temperature

Test

Push the top of the Thermostat until

it displays « MAX ».

The Thermostat switches

the boiler on.

Push the bottom of the Thermostat

until it displays « OFF ».

The Thermostat switches the boiler

o.

Note: If the Thermostat doesn’t switch on and o the boiler, the control wires have been incorrectly

wired. In this case, check your wiring using the picture of your old thermostat’s wiring to identify the right

control wires.

If the boiler does the opposite of what is described (for example, it switches OFF when the Thermostat

displays MAX), it means that you will have to change the polarity of the Thermostat. You can modify the

polarity in the advanced settings of the app once you will have ﬁnished the setup.

clic

To use your Thermostat from your smartphone or tablet, visit:

http://therm.netatmo.com

App

Smartphone / Tablettes

Speciﬁcations

SIZE

Thermostat: 83 x 83 x 22 mm

DESIGN

Translucent minimalist plexiglass cube.

5 interchangeable colours in the box.

SENSORS AND MEASUREMENTS

Temperature (measurement):

Ranges from : 0°C à 50°C

Accuracy: -/+ 0,1°C

Temperature (setpoint):

Ranges from: 5°C à 30°C

Incrément: 0.5°C

Unit: °C

E-INK DISPLAY

Energy ecient, longer battery life and

optimal readability.

FREE APP, LIFETIME SUPPORT

No subscription fee.

App available on the App Store,

Windows Phone Store and on

Google Play.

Free access to your online personal

dashboard.

Accessible from multiple devices.

WIRELESS SPECIFICATIONS

Wi-Fi 802.11 b/g/n compatible (2.4GHz).

Supported security: Open/WEP/WPA/

WPA2-personal (TKIP and AES).

Wireless connection between thermostat and

relay:

radio long range 100 m.

POWER AND BATTERIES

3 AAA batteries.

2 years battery life.

SETUP AND COMPATIBILITY

Compatible with gas, fuel, wood boilers

and heat pumps.

Switching current: max 4 A

Switching voltage: max 250 VAC

Switching power: max 120 W

HOMEKIT

Controlling HomeKit-enabled accessories away

from home requires an Apple TV (3rd generation

or later) with Apple TV software 7.0 or later and an

iPhone, iPad, or iPod touch with iOS 8.1 or later.

M1-V7-EN

V16

Complies with

IDA Standards

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Cet appareil est conforme aux normes CNR exemptes de licence d'Industrie

Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1) cet

appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter

toute interférence, y compris celles susceptibles de provoquer un fonctionnement

non souhaité de l'appareil.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

This device and its antenna(s) must not be co-located or operating in

conjunction with any other antenna or transmitter.

Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnant en

conjonction avec une autre antenne ou transmetteur.

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment. This transmitter should be installed and operated

with a minimum distance of 20 centimeters between the radiator and your

body and must not be co-located or operating in conjunction with any other

antenna or transmitter. This equipment complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference

that may cause undesired operation.

EU Declaration of Conformity

We, Netatmo, declare that this device is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC.

Taiwan Wireless Statements

無線設備的警告聲明

本產品符合低功率電波輻射性電機管理辦法󵛑第〸二條、第〸四條等

條文規定:󵛑

1.󵛑經型式認證合格之低功率射頻電機，非經許可，公司、商號或使

用�均不得擅自變更頻率、加大功率或變更原設計之特性及功能。󵛑

2.󵛑低功率射頻電機之使用不得影�飛航安全及干擾合法通信；經發

現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。󵛑

前項合法通信，指依電信法規定作業之無線電通信。󵛑

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性

電機設備之干擾。

EU Declaration of Conformity

We, Netatmo, declare that this device is

in compliance with the essential require-

ments and other relevant provisions of

Directive 1999/5/EC.

Safety warnings

This device must be installed according

to the applicable norms. Use only with

supplied power plug adaptor and boiler

adaptor. This device is for indoor use

only.

Before inserting the batteries, check that

the contacts in the device and on the

batteries are clean, is necessary clean

them. Note the polarity (+/-) when inserting

the batteries. Do not throw the batteries

into a ﬁre, short-circuit them or dismantle

them. Keep children away from batteries.

Seek medical attention immediately if a

battery is swallowed. Do not attempt to

repair the device yourself; customer

service is available. Any changes or

modiﬁcations to this unit not expressly

approved by the party responsible for

compliance could void the user’s authority

to operate the equipment. Thermostat and

relay insulation: class II devices. This

device is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge, unless they

have been given supervision or instruc-

tion concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to ensure

that they do not play with the appliance.

Legal notice

Use of the HomeKit logo means that

an electronic accessory has been de-

signed to connect speciﬁcally to iPod,

iPhone, or iPad, respectively, and has

been certiﬁed by the developer to meet

Apple performance standards. Apple is

not responsible for the operation of this

device or its compliance with safety and

regulatory standards.

Please note that the use of this acces-

sory

with iPod, iPhone, or iPad may aect wi-

reless performance.

Netatmo Smart thermostat Manuel utilisateur

Marque: Netatmo

Modèle: Smart thermostat

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Netatmo Smart thermostat User manual

Netatmo Smart thermostat Manuel utilisateur

Netatmo Smart thermostat Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents