Marvel MP24BRF4LP Le manuel du propriétaire

MP15BCG4**

MP15BCF4**

MP24BCG4**

MP24BCF4**

MP24BRG4**

MP24BRF4**

MP24RAS4**

MP24RAP4**

MP24WBG4**

Built in Refrigerators

Réfrigérateurs intégrées

Refrigeradores

empotradas

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

ES Instrucciones de instalación, operación y mantenimiento

2

NOTE

!

CAUTION

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Product dimensions ............................................................6

Using your Electronic control .............................................8

Starting your appliance ...................................................8

Sleep mode ....................................................................8

Turning your appliance "ON" or "OFF" ...........................8

Interior display lighting ....................................................9

Adjusting the temperature ..............................................9

Temperature mode ........................................................10

Control lock ...................................................................10

Temperature sensor error codes ...................................10

Alarms ..........................................................................11

Door ajar ...................................................................11

Power failure ............................................................11

Temperature alarm ...................................................11

Vacation mode ..............................................................12

Overlay door panel installation ........................................12

Shelving congurations ....................................................18

Care and cleaning .............................................................21

Energy saving tips .............................................................21

Obtaining service .............................................................22

Troubleshooting ................................................................23

Warranty ...........................................................................24

is committed to building a quality product

in an environmentally friendly manner. Our processes are

tightly controlled and closely monitored. We have achieved

certications in ISO 9001 for quality assurance, ISO 14001

for environmental management, and OHSAS 18001 for oc-

cupational health and safety from Lloyd’s Register Quality

Assurance.

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

CONTENTS

!

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

3

NOTE

!

CAUTION

XXXXXXXXXXXX

!

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

!

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

!

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Figure 1

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.agamarvel.com.

The following information will

be required when registering

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the left

side near the top. See gure 1.

Warranty Registration

UNPACKING YOUR APPLIANCE

Online registration

available at

www.agamarvel.com

4

!

CAUTION

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to specications, the recom-

mended installation location temperature range is from 55

to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unobstruct-

ed. All Marvel Professional models with articulated hinges

are intended for built-in applications only.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area to not be obstructed and the grille

openings kept clean. AGA MARVEL does not recommend

the use of a custom made grille as air ow may be restrict-

ed. (See Figure 2).

INSTALLING YOUR APPLIANCE

!

WARNING

An optional stacking kit, for 24" wide models, is re-

quired to stack products. Failure to use a stacking kit

could result in personal injury. Contact your dealer or

Aga Marvel customer service at 800-223-3900 to order.

For safety concerns 15" wide models should not be

stacked.

Figure 2

Front Leveling

Legs

Front Grille,

keep this area

open.

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the

oor and level from side to side and front to back. The over-

all height of your Marvel appliance may be adjusted higher

(by turning the leveling leg out, CCW) and lower (by turning

the leveling leg in, CW) dimensions as shown in Table "A".

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

Rear

Leveling

Legs

Model Door Style

Minimum

Height

Maximum

Height

MP(15)(24)* (S) or (G)

33

3

⁄4"

(85.7 cm)

34

3

⁄4"

(88.3 cm)

MP(15)(24)* (F)

34"

(86.4 cm)

35"

(88.9 cm)

Table A

5

NOTE

INSTALLING YOUR APPLIANCE

Figure 5

Front grille screw

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

!

WARNING

Front grille

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Figure 6

Figure 3

Figure 4

Do not remove

ground prong

6

"A"

"B"

"C"

"D"

"E"

PRODUCT DIMENSIONS

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

MP15BCG

15"

(38.1 cm)

**34" to 35"

(86.4 to 88.9 cm)

24"

(61 cm)

14

7

⁄8"

(37.8 cm)

33

3

⁄4" to 34

3

⁄4"

(85.7 to 88.3 cm)

23

⁄32"

(60.2 cm)

26

7

⁄32"

(66.6 cm)

37

13

⁄32"

(95 cm)

17

7

⁄16"

(44.3 cm)

MP15BCF

15"

(38.1 cm)

**34

1

⁄4" to 35

1

⁄4"

(87 to 89.5 cm)

* 24"

(61 cm)

14

7

⁄8"

(37.8 cm)

34" to 35"

(86.4 to 88.9 cm)

22

7

⁄8"

(58.1 cm)

-

7

1

⁄2"

(95.2 cm)

14

1

⁄8"

(35.9 cm)

MP24**S

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

24"

(61 cm)

23

7

⁄8"

(60.7 cm)

33

3

⁄4" to 34

3

⁄4"

(85.7 to 88.3 cm)

23

⁄32"

(60.2 cm)

26

7

⁄32"

(66.6 cm)

46

13

⁄32"

(117.9 cm)

26

7

⁄16"

(67.2 cm)

MP24**G

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

24"

(61 cm)

23

7

⁄8"

(60.7 cm)

33

3

⁄4" to 34

3

⁄4"

(85.7 to 88.3 cm)

23

⁄32"

(60.2 cm)

26

7

⁄32"

(66.6 cm)

46

13

⁄32"

(117.9 cm)

26

7

⁄16"

(67.2 cm)

MP24**F

24"

(61 cm)

**34

1

⁄4" to 35

1

⁄4"

(87 to 89.5 cm)

* 24"

(61 cm)

23

7

⁄8"

(60.7 cm)

34" to 35"

(86.4 to 88.9 cm)

22

7

⁄8"

(58.1 cm)

-

46

1

⁄2"

(118.1 cm)

23

1

⁄8"

(58.7 cm)

DOOR STYLE

(S) Solid Door

(G) Glass Frame Door

(F) Frame Glass Overlay Door (no handle)

Figure 7

(S) solid door

shown

Figure 7a

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 8).

Figure 8

7

"D"

"E"

"F"

"G"

"H"

"J"

PRODUCT DIMENSIONS

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

MP15BCG 115V/60Hz/15A

105 lbs

(47.6 kg)

MP15BCF 115V/60Hz/15A

105 lbs

(47.6 kg)

MP24**S 115V/60Hz/15A

140 lbs

(63.6 kg)

MP24**G 115V/60Hz/15A

140 lbs

(63.6 kg)

MP24**F 115V/60Hz/15A

140 lbs

(63.6 kg)

* To install (F) models with the door face ush with adja-

cent cabinetry doors, custom decorative panel thickness

cannot exceed

3

⁄4" (19 mm).

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

3

1

⁄2" (8.9 cm)

Minimum

Figure 9

(S) solid door

shown

21

1

⁄2"

(54.6 cm)

8

USING YOUR ELECTRONIC CONTROL

Power Failure

ALARM RESET

Turning your appliance ON and OFF (single

and dual zone):

If the appliance is "On", (and out of sleep mode) the tem-

perature will be shown in the display area of the control.

To turn the appliance "Off", press and hold the "On/Off"

keypad for 4-seconds. "OFF" will now be displayed on the

control.

To turn the appliance "On", press and hold the "On/Off"

keypad for 4-seconds.

The sleep mode can be disabled if you prefer to have the

display on continuously. Press and hold the "Lock" key-

pad until the display goes past "Loc" and reads "nSL". To

enable the sleep mode, repeat the instruction, again going

past "Loc" until the display reads "SLP".

To wake the display press any keypad. A conrm tone will

sound, and the current storage compartment temperature

will be displayed.

Sleep mode (single and dual zone):

If no keypads are pressed for 60 seconds, the display will

enter sleep mode to conserve power. The control panel will

go dark with the exception of the system status "OK" indi-

cator which will remain enabled. Alarm conditions will wake

the display, (see alarms on page 11).

To make the following changes to the control settings

(turning the appliance ON/OFF, adjusting the tempera-

ture, changing the interior lights, and activating vaca-

tion mode), the control must be awake.

Starting your appliance (single and dual

zone):

Plug the appliance power cord into a 115 volt wall outlet.

Your appliance is shipped from the factory in the "On" posi-

tion and will begin start-up of cooling as soon as power is

supplied. If the appliance does not start, conrm that the

wall outlet has power, and that the control is in the "On"

position, (See "Turning your appliance On and Off" below).

The control display is covered with a clear plastic lm. This

lm may be removed by carefully lifting the lm at a corner.

On initial power up, the control display will indicate a

"Power Failure" alarm. This is a normal condition as the ap-

pliance was powered-up at the factory for quality inspection

and then removed from power. A momentary press of the

"On/Off" keypad will reset this alarm condition. (See Alarms

section on page 11).

Figure 10

Electronic control

Lights

keypad

Upper/Lower

zones

(Dual Zone

models only)

Temp

Minus

keypad

Temp

Plus

keypad

On/Off

keypad

Display Area

Lock

keypad

System Status

indicators

9

USING YOUR ELECTRONIC CONTROL

Display lighting :

Display lighting is intended for glass door models only, to

illuminate the interior with the door closed.

With the control out of sleep mode press the "Light" keypad

once to activate the interior lighting display feature at full

illumination. A conrmation tone will sound, and the light

bulb "Icon" will illuminate. Pressing the "Light" keypad a

2nd time will dim the lighting to 50%. A 3rd press will deacti-

vate the display lighting feature. The display lighting will

automatically deactivate after 4-hours.

If you have a solid door/drawer product the display lighting

function is only used to select the color of the interior light.

Changing the Tri-Color lighting:

To change the color between white, amber, or blue, with the

control out of sleep mode, momentarily press the "Light"

keypad. The keypad will illuminate. Then press and hold

the keypad for approximately 3 seconds the interior light

will start to cycle through the 3 available colors. On solid

door/drawer product this will need to be done with the door/

drawer open to be able to observe the colors. Release the

keypad when the desired color is on, and your interior light

will be changed to that color. After selection of color for

solid door/drawer product, the display light feature should

be turned-off, ("Light" keypad not illuminated).

Interior Lighting:

Adjusting the Temperature:

NOTE

When initially loading your product with warm contents, it

may take up to 48-hours for the storage compartment tem-

perature to stabilize.

When making temperature set-point changes, it may take

up to 24-hours for the stored contents to stabilize at your

new set-point temperature.

Factors that affect the storage compartment stabilized

temperature:

• Changes to temperature setting.

• Room temperature changes.

• Temperature of stored contents.

- Loading warm contents.

- Cold content load will delay the change to a warmer

set-point temperature.

- Warm content load will delay the change to a colder

set-point temperature.

• Usage, (number and duration of the door openings).

• Use of the storage compartment display lighting, (glass

door product only).

• Installation of the appliance in direct sunlight or next to

a heat source.

Single Zone Models:

To set or check the set-point temperature (with the control

out of sleep mode), press the "-" or "+" keypads. "SET" will

be indicated on the user interface panel and the current

set-point temperature will display and ash. Subsequent

presses of the "-" or "+" keypads will adjust the temperature

colder or warmer respectively. When you have reached

your desired set-point temperature, press the "On/Off" key-

pad to accept, or do nothing and the "Set" mode will time-

out in 10-seconds accepting the displayed temperature as

the new set-point.

The available set-point temperature range for your ap-

pliance is 34°F (1.2°C) to 42°F (5.7°C). If you attempt to

adjust the temperature outside of this range you will receive

an audible notication.

Lower zone

selected

Upper zone

selected

Dual Zone Models:

Temperatures can be set for each individual zone (upper

and lower) in the dual zone wine / beverage center. To

do so you must rst select the zone you want to set the

temperature for. You do so by pressing the upper or lower

button on the display. When pressed the LED light will be

illuminated for the respective display.

10

USING YOUR ELECTRONIC CONTROL

Control lock:

The control panel can be locked to avoid unintentional

changes. To lock the control, press and hold the "Lock" key-

pad until the display reads "Loc" then immediately release

your nger from the keypad. The lock icon will ash 3-times

and then continuously illuminate. When the control panel is

locked, only the Lock keypad, System Status OK indicator

, and the Alarm indicator are active. To un-lock the control

panel, repeat this instruction until the display reads "nLc",

then immediately release your nger from the keypad.

The temperature sensors are monitored continuously. Any

OPEN or SHORTED circuit condition will initiate an

ERROR CODE as listed below:

Temperature Sensor Error Codes

Temperature mode:

The temperature mode is preset from the factory in Fahren-

heit (°F) but you have the option to change it to Centigrade

(°C). To change the mode, press and hold the "-" keypad,

while pressing the "+" keypad, then release the "-" keypad.

The temperature will now be displayed in Centigrade (°C).

Repeat the procedure to change the temperature mode

back to Fahrenheit (°F).

To change the set temperature for a particular zone, with

the zone selected and out of sleep mode, press the "-" or

"+" keypads. "SET" will be indicated on the user interface

panel and the current set-point temperature will display

and ash. Subsequent presses of the "-" or "+" keypads

will adjust the temperature colder or warmer respectively.

When you have reached your desired set-point tempera-

ture, press the "On/Off" keypad to accept, or do nothing

and the "Set" mode will time-out in 10-seconds accepting

the displayed temperature as the new set-point.

The available set-point temperature range for your appli-

ance is 34°F (1.2°C) to 42°F (5.7°C) for the lower zone

and 45°F (7°C) to 60°F (16°C) for the upper zone. If you

attempt to adjust the temperature outside of these ranges

you will receive an audible notication.

NOTE

The upper zone is designed exclusively for the storage of

wine. The upper zone cannot attain storage temperatures

suitable for fresh food storage.

Temperature Sensor Error Codes

Sensor Displayed Code Error Description Action to Take

Single Zone

Temperature Sensor

Failed temperature sensor in the single

zone compartment. Can lead to unwant-

ed wine storage temperatures.

Call service to have the tem-

perature sensor replaced.

Defrost Sensor

Failed defrost temperature sensor.

Causes unit to not defrost properly and

can create large frost build-up. Can lead

to water damage to the unit and sur-

rounding oor.

Unplug the power cord imme-

diately and call service to have

the defrost sensor replaced.

Single Zone Models:

Dual Zone Models:

Temperature Sensor Error Codes

Sensor Displayed Code Error Description Action to Take

Upper Zone

Temperature Sensor

Failed temperature sensor in the upper

zone compartment. Can lead to unwant-

ed wine storage temperatures.

Call service to have the tem-

perature sensor replaced.

Lower Zone

Temperature Sensor

Failed temperature sensor in the lower

zone compartment. Can lead to unwant-

ed wine storage temperatures.

Call service to have the tem-

perature sensor replaced.

Defrost Sensor

Failed defrost temperature sensor.

Causes unit to not defrost properly and

can create large frost build-up. Can lead

to water damage to the unit and sur-

rounding oor.

Unplug the power cord imme-

diately and call service to have

the defrost sensor replaced.

11

NOTE

If the control lock is active (illuminated lock icon) the control

will have to be unlocked before using the keypad to reset

an alarm condition. See page 10 (Control Lock) for instruc-

tions for unlocking the control.

USING YOUR ELECTRONIC CONTROL

Door Ajar

ALARM RESET

Power Failure

ALARM RESET

Temp

NOTE

Door Ajar

Temp

This alarm condition can be reset by closing the door or

momentarily pressing the "On/Off" keypad, (i.e.-if you

are cleaning the storage compartment, etc.). The alarm

will recur in 5-minutes if the alarm condition persists.

• Power failure - If power to the appliance is inter-

rupted the System Status indicator will turn-off and

the "Power Failure" indicator will ash. Additionally, an

"ALARM RESET" indicator will be displayed below the

"On/Off" keypad. No audible tone will sound. This alarm

condition can be reset by momentarily pressing the

"On/Off" keypad. If this alarm occurs, it is recommend-

ed that you check the condition of any perishables,

even if the appliance is operating normally and the tem-

perature has recovered, as prolonged power outages

could result in excessive temperature excursions which

may spoil perishables.

• Temperature alarm - If the storage compart-

ment temperature deviates excessively from your

set-point temperature for an extended period of time,

the "TEMP" indicator will ash, and an audible tone

will sound every 60 seconds. Additionally, an "ALARM

RESET" indicator will be displayed below the "ON/

OFF" keypad.

Multiple alarms are possible, i.e.- "Door Ajar" for a pro-

longed period may trigger a "Temp" alarm, in which case

both "Door Ajar" and "Temp" indicators will activate.

Alarms (single and dual zone):

The control will alert you to conditions that could adversely

affect the performance of the appliance.

• Door ajar - If the door is open, or not closed prop-

erly, for more than 5-minutes the System Status OK

indicator will turn-off, the "Door Ajar" indicator will ash,

and a tone will sound every 60 seconds. Additionally,

an "ALARM RESET" indicator will be displayed below

the "On/Off" keypad.

NOTE

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

NOTE

The audible alarm can be muted, for each occurrence, by

pressing the lock keypad.

This alarm condition can be reset by momentarily pressing

the "On/Off" keypad. If this alarm occurs it is recommended

that you check the condition of your stored contents, even

though the appliance is operating normally and the temper-

ature has recovered, as prolonged temperature excursions

could spoil perishables.

NOTE

After a high temperature alarm condition, check all perish-

ables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage compart-

ment. If the temperature alarm continues to occur, your unit

may require service.

12

!

CAUTION

Overlay door panel installation:

Step 1: Removing the Door

With a phillips screwdriver remove the screw and "P" clamp

from the bottom of the door near the hinge. See Figure 11b.

Disconnect the door wire harness by pressing and holding

down the locking tab on the wire connector and pulling the

connector apart. See Figure 12.

Open the door and loosen the screws holding the hinges to

the cabinet (2 at the top and 2 at the bottom hinge). Do not

remove the screws but loosen them enough so the hinges

can be slipped off of the screws when sliding the door to

the side.

With a helper, and being careful not to scratch the cabinet

or the door, slide the door to the side about

1

⁄2 inch and

remove the hinges and door from the unit.

!

WARNING

Overlay panel models are designed for use with built-

in installations only. Use in freestanding installations

could result in personal injury.

If you purchased an overlay panel model, your unit is

equipped with articulated hinges to allow fully integrated

built-in installations. Custom panel thicknesses of

5

⁄8" (15

mm) and

3

⁄4" (18 mm) are accommodated.

It is important to use the factory provided grille that came

with the product to assure proper air ow is maintained

through the condenser. The use of a custom grille is not

recommended and will void the warranty.

!

WARNING

The articulated hinges have many pinch points. Care-

fully close / collapse the hinges as soon as the door is

removed from the cabinet.

OVERLAY DOOR PANEL INSTALLATION

Vacation mode (single and dual zone):

This operating mode can be used to save energy during

high cost energy periods, or when you won't be using your

appliance for an extended period of time by disabling the

lights, alarm tones, and keypad entry tones. Vacation mode

also serves as a Sabbath mode, disabling functions and

its controls in accordance with the weekly Sabbath and

religious holidays observed within the Orthodox Jewish

community. When used as Sabbath mode, you may open

or close the door at any time to access contents without

concern of directly turning on or off any lights, digital read-

outs, solenoids, fans, valves, compressor, icons, tones, or

alarms.

When activated, the display, alarm indicators and tones,

keypad touch tones, interior lights, and all options are dis-

abled. All keypad functions are disabled, with the exception

of the "On/Off" keypad which is required to exit Vacation-

mode. Storage compartment temperatures are monitored

and controlled at the settings prior to entering Vacation

mode.

To enter Vacation Mode (with the control out of sleep

mode), press and hold the "On/Off" keypad until the display

goes past "OFF" and reads "VAC". The display will ash

"VAC" 3-times to acknowledge your request, then will

display "VAC" continuously until Vacation mode is exited.

A power outage will not exit Vacation mode, exiting can

only be accomplished manually. To exit Vacation mode and

return to normal operation, press and hold the "On/Off"

keypad until the control displays the temperature.

13

OVERLAY DOOR PANEL INSTALLATION

Overlay panel

ush with top

and side of

door.

Magnetic Gasket

remove starting at a

corner, grasp and pull

away from the door.

Step 3: Cut and drill the overlay panel

Depending on your model cut the overlay door panel to the

dimensions shown in Figures 14 to 21. The window cut out

is for glass door models only. If your appliance has a lock

also drill the lock hole in the panel, see Figure 22.

Overlay panel to

be centered on

width of door.

Figure 13

Holes in

gasket

retainer.

Figure 12

Press and hold this down

this tab on the wire connec-

tor and pull the connector

apart.

Figure 13a

Step 2: Remove the door gasket

With the door laying on a at surface and starting at a

corner of the door remove the magnetic door gasket from

the interior side of the door, see Figure 13. Set the gasket

aside on a at surface.

There are 10 holes in the gasket retainer extrusions, (3 on

each side and 2 at the top and bottom which are used to

fasten the panel to the front of the door. The screws are

provided in the literature pack along with the door lock,

which is provided on certain models.

Loosen (do not remove ) these

2 phillips head screws on the

top and bottom hinges

!

WARNING

Use extreme caution with the articulated hinges. The

hinge is self closing and many pinch points exist prior

to built-in installation. Do not remove the cabinet "Z"

bracket from the top of the cabinet.

Figure 11b

Bottom of

door

"P" clamp

and screw

Wire connector

see Figure 12

Figure 11

Figure 11a

Cabinet

"Z" Bracket

14

!

CAUTION

1

5

⁄32"

(2.9 cm)

1

5

⁄32"

(2.9 cm)

OVERLAY DOOR PANEL INSTALLATION

Weight of overlay door panel must not

exceed 15 pounds (6.8 kg) for a solid

door model or 10 pounds (4.5 kg) for a

glass door model.

Clearance

for hinge

2 places

Figure 17

Right Hand Hinged Door

15" (38.1 cm) wide appliance

14

3

⁄4"

(37.5 cm)

Clearance for

screw head,

4 places

Figure 14

Left Hand Hinged Door

15" (38.1 cm) wide appliance

Hinge side of door

Clearance

for hinge

2 places

14

3

⁄4"

(37.5 cm)

1

⁄4" (6 mm)

Deep

1" (25.4 mm) diameter

counter bore

1

⁄4" (6.4mm)

deep 4 places.

1

3

⁄4"

(4.4 cm)

Figure 15

Left Hand Hinged Door

15" (38.1 cm) Wide Appliance

4

7

⁄8"

(12.4 cm)

3

27

⁄32"

(9.7 cm)

1

11

⁄16"

(4.3 cm)

5"

(12.7 cm)

3

1

⁄8"

(7.9 cm)

Minimum

2"

(5.1 cm)

4

1

⁄8"

(10.5 cm)

Minimum

30

11

⁄32"

(77.1 cm)

1

3

⁄16"

(3 cm)

3

1

⁄8"

(7.9 cm)

1

⁄2"

(3.8 cm)

typical

3

11

⁄16"

(9.4 cm)

3

1

⁄8"

(7.9 cm)

Minimum

This side

facing interior

This side

facing interior

1

⁄4" (6 mm)

radius is

permissible

Hinge side of door

Top of door

Clearance for

screw head,

4 places

Figure 16

Right Hand Hinged Door

15" (38.1 cm) wide appliance

3

27

⁄32"

(9.7 cm)

1

⁄4" (6 mm)

Deep

5"

(12.7 cm)

1" (25.4 mm) diameter

counter bore

1

⁄4" (6 mm)

deep 6 places.

1

⁄4" (6 mm)

radius is

permissible

30

11

⁄32"

(77.1 cm)

4

7

⁄8"

(12.4 cm)

3

1

⁄8"

(7.9 cm)

1

⁄2"

(3.8 cm)

typical

1

3

⁄4"

(4.4 cm)

3

1

⁄8"

(7.9 cm)

Minimum

2"

(5.1 cm)

3

11

⁄16"

(9.4 cm)

4

1

⁄8"

(10.5 cm)

Minimum

1

11

⁄16"

(4.3 cm)

3

1

⁄8"

(7.9 cm)

Minimum

1

3

⁄16"

(3 cm)

15

1

5

⁄32"

(2.9 cm)

Top of door

1

5

⁄32"

(2.9 cm)

OVERLAY DOOR PANEL INSTALLATION

Figure 20

Right Hand Hinged Door

24" (61 cm) wide appliance

Figure 21

Right Hand Hinged Door

24" (61 cm) wide appliance

1" (2.5 cm) diameter

x

1

⁄4" (6 mm) deep

4 places

Clearance

for hinge

at top and

bottom

2"

(5.1 cm)

3

11

⁄16"

(9.4 cm)

1

⁄2"

(3.8 cm)

typical

1

⁄4"

(6 mm)

Deep

Hinge side of door

Clearance for

screw head,

4 places

30

11

⁄32"

(77.1 cm)

1

11

⁄16"

(4.3 cm)

23

3

⁄4"

(60.3 cm)

3

1

⁄8"

(7.9 cm)

Top of door

3

1

⁄8"

(7.9 cm)

1

3

⁄4"

(4.4 cm)

4

1

⁄8"

(10.5 cm)

1

⁄4" (6 mm)

radius is

permissible

This side

to door

3

1

⁄8"

(7.9 cm)

3

27

⁄32"

(9.8 cm)

1

3

⁄16"

(3 cm)

14"

(35.6 cm)

4

7

⁄8"

(12.4 cm)

Figure 19

Left Hand Hinged Door

24" (61 cm) wide appliance

Figure 18

Left Hand Hinged Door

24" (61 cm) wide appliance

Hinge side of door

Clearance

for hinge

at top and

bottom

Clearance for

screw head,

4 places

23

3

⁄4"

(60.3 cm)

1

3

⁄4"

(4.4 cm)

1

⁄4"

(6 mm)

Deep

1" (2.5 cm) diameter

x

1

⁄4" (6 mm) deep

4 places

3

1

⁄8"

(7.9 cm)

2"

(5.1 cm)

3

11

⁄16"

(9.4 cm)

1

⁄2"

(3.8 cm)

typical

1

11

⁄16"

(4.3 cm)

30

11

⁄32"

(77.1 cm)

14"

(35.6 cm)

1

3

⁄16"

(3 cm)

3

1

⁄8"

(7.9 cm)

4

7

⁄8"

(12.4 cm)

4

1

⁄8"

(10.5 cm)

This side

to door

3

1

⁄8"

(7.9 cm)

1

⁄4" (6 mm)

radius is

permissible

3

27

⁄32"

(9.8 cm)

16

!

CAUTION

OVERLAY DOOR PANEL INSTALLATION

Step 4: Assemble the panel to the door

The preferred method of attaching the panel to the door

is to clamp the panel to the door so it cannot move while

drilling the screw pilot holes. Use bar clamps or "C" clamps

with pads on the clamping surfaces that will not mar the

panel or the door. The custom overlay panel should be

ush with the top of the door and centered along the width

of the door. See Figure 13a. Drill holes through the gasket

extrusion using the 10 holes as pilot holes. Use the drill

size from the chart in Table "B", being careful not to drill

through the front surface of the panel. If the overlay panel is

thinner than

5

⁄8" (16 mm) thick shorter screws will have to be

obtained. Fasten the panel to the door with the 10 screws

provided in the literature pack. (See Figure 22a). Remove

the clamps and replace the gasket in the gasket extrusion

channels of the door. Some force may be required to seat

the gasket into the channels. Be sure the gasket corners

are seated properly.

Material Type #10 Wood Screw

Hardwood

1

⁄8" (3.2 mm) Diameter. Pilot Hole

Softwood

7

⁄64 (2.8 mm) Diameter. Pilot Hole

Table B

Weight of overlay door panel must not exceed 15

pounds (6.8 kg) for a solid door model or 10 pounds

(4.5 kg) for a glass door model.

Figure 22

3

1

⁄2"

(89 mm)

Counter bore

lock hole

on back side.

Figure 22a

#10 x

1

⁄2"

screw

1

⁄2" (13 mm) diameter drill

through door panel, from

other side (see detail

above)

13

⁄16" (20.5 mm)

counter bore,

7

⁄16" (11 mm)

deep.

17

⁄32"

(13.7 mm)

Hinge side of door

17

Cabinet

"Z" bracket

#8 x

3

⁄4" black

screws

(3 places)

Figure 25

Step 7: Install the door

Carefully open the top and bottom hinges on the door being

careful as there are many pinch points. Place the hinges

over the 4 screws in the cabinet, 2 at the top and 2 at the

bottom and slide the door into position. Tighten the 4 hinge

screws with a phillips screwdriver. (See Figures 11 and

11a). Place wire harness from the grille and mount to the

bottom of the door with the screw and "P" clamp removed

in step 1. (See Figure 11b). Reconnect the wire harness,

(See Figure 12).

SECTION A-A

SCALE 1 : 1

LOCK

NUT

BRASS EXTENSION

CAM

PHILLIPS SCREW

13/16 COUNTER

BORE 7/16 DEEP

1/2 HOLE

3/4 INCH

WOOD PANEL

SPRING WASHER

INNER

DOOR

Step 8: Secure the cabinet

Use the #8 x

3

⁄4" black screws from the literature pack to

secure the counter top to the cabinet top through the holes

in the cabinet "Z" bracket.

OVERLAY DOOR PANEL INSTALLATION

Figure 24

Step 6: Install lock cam

Attach the lock cam to the back of the lock assembly with

the phillips head screw provided. Orient the lock cam verti-

cally when installing on the lock.

Cam stop

washer

Spring

washer

Cam

Set screw

Lock

Key

Retainer

nut

Screw

Brass

extension

(2 lengths

provided)

Step 5: Assemble lock parts

Two (2) lock extensions are provided with the lock. Use the

longer extension for

3

⁄4" thick overlay panels and the shorter

one for

5

⁄8" thick overlay panels. Assemble the lock exten-

sion, cam stop washer, spring washer, and set screw to the

lock as shown in Figure 23 and 24.

Install this lock assembly into the lock hole in the overlay

panel and secure with the retaining nut on the back side

with a 15 mm socket and ratchet. Make sure the key slot in

the front of the lock is vertical.

Figure 23

18

SHELVING CONFIGURATIONS

Refrigerator:

Beverage Center:

Loading Tips and Suggestions

Your appliance is equipped with a cantilever shelf system

which provides maximum adjust ability and customizing of

the shelving arrangements listed below.

24" (61 cm) Wide Models:

Shown with a solid door with door racks. Figure 28.

24" (61 cm) Wide Models:

Shown with a glass overlay door. Figure 27.

15" (38.1 cm) Wide Models:

Shown with a glass door. Figure 26.

(1) half width metal cantilever shelf

(See Figure 36).

(1) full width slide out cantilever metal shelf.

(See Figure 35).

(1) frame and at glass crisper cover.

(1) roll-out crisper pan.

(1) full width door storage rack.

(1) half width door storage rack.

Figure 26

Figure 28

(2) glide out wine convertible glass shelf (See

Figure 31).

(2) glide out wine convertible glass shelf. (See Figure 32).

(1) Five bottle rollout display rack with vibration dampening

mat (See Figure 33).

Figure 27

Figure 29

Beverage Refrigerator:

24" (61 cm) Wide Models:

Shown with a glass door. Figure 29.

(1) half width at glass cantilever shelf. (See Figure 34).

(1) wine cutout and at glass cantilever shelf.

(See Figure 32).

(1) frame and at glass crisper cover.

(1) roll-out crisper pan

Dual Zone Wine / Beverage Center

24" (61 cm) Wide Models:

Upper Zone:

(1) Seven bottle rollout wine display rack with

vibration dampening mat. (See gure 37).

Lower Zone:

(1) Four bottle rollout wine shelf with glass and

vibration dampening mat. (See gure 39).

(1) Three quarter wide rollout glass shelf and

frame. (See gure 38).

Figure 30

19

Figure 31

glide out wine

convertible glass shelf

SHELVING CONFIGURATIONS

Wine shelf

underneath glass

Figure 32

Wine cutout and at glass shelf with

vibration dampening mat, the glass

can be removed for wine storage.

Figure 33

5 bottle rollout display

rack with vibration

dampening mat

Figure 35

Slide out metal cantilever shelf

Figure 36

half width metal cantilever

shelf

Figure 34

Frame and at glass shelf

with trim

Figure 37

Figure 38

Figure 39

20

Tall bottle

storage

area

To Add or Remove a Shelf

Remove stored product from the shelf. Do not try to remove

a loaded shelf from the appliance. Grasp the shelf front with

both hands, rotate the front upward and lift out. (See Figure

40b). To install a shelf insert the shelf in the appliance and

insert the top hooks into the shelf support slots and drop

the shelf down so the hooks drop over the bottom of the

slots.

Rear tang

(hook) on

shelf

Shelf support

slot

Installed shelf

tang

Make sure your cantilever shelf is secure on the shelf

supports by pressing down on the shelf before loading the

shelf.

!

CAUTION

Grasp the shelf by the front with

both hands and rotate the front

of the shelf up, then lift the shelf

up and remove the shelf from the

shelf ladders.

!

CAUTION

Never try to move a loaded shelf, remove everything from

the shelf before moving. Use both hands when moving a

shelf.

Figure 40a

Figure 40

Figure 40b

SHELVING CONFIGURATIONS

To remove the crisper :

Pull out until it stops. Lift up on the

front of the pan, and remove it from

the frame.

Door storage racks

Tall bottle

storage area

Figure 41

La page charge ...

Marvel MP24BRF4LP Le manuel du propriétaire

Marvel MP24BRF4LP Le manuel du propriétaire

dans d''autres langues

Documents connexes