Friedrich MR24DY3JMA Mode d'emploi

Installation Manual

TYPE : Multi Type

ENGLISH

FRANÇAIS

ESPAÑOL

960-911-09

MULTIZONE INSTALLATION

INSTRUCTIONS

Installation Manual 3

ENGLISH

TABLE OF CONTENTS

Installation Parts Provided ...................................................4

Safety Precautions ................................................................5

Installation of Indoor, Outdoor Unit .....................................8

Select the best location ....................................................8

Seaside Applications and Installation ..............................10

Seasonal Wind And Cautions In Winter...........................11

Piping length and elevation .............................................12

Installation............................................................................14

Ceiling dimension and hanging bolt location ...................14

How to Fix .......................................................................15

Wiring Connection ...........................................................15

Conduit connection..........................................................15

Installation of Decorative Panel.......................................16

Drain Piping.....................................................................19

Flaring Work and Connection of Piping ............................21

Flaring work.....................................................................21

Connection of piping - Outdoor .......................................22

Installation .......................................................................25

Installation of The Main Unit............................................26

Connecting the Cable between Indoor Unit, Distributor

Unit and Outdoor Unit .........................................................27

Connect the cable to the Indoor unit. ..............................27

Connect the cable to the Distributor unit .........................28

Connect the cable to the Outdoor unit.............................29

Connection method of the connecting cable(Example)...31

Checking the Drainage, Insulating the Pipe and Special

Piping Applications .............................................................32

Checking the drainage ....................................................32

Insulating the Pipe and Special Piping Applications........32

Air Purging and Evacuation................................................33

Leak Checking.................................................................33

Evacuation.......................................................................34

Charging ...............................................................................35

Test Running ........................................................................37

Function................................................................................38

Dip S/W Setting ...............................................................38

Forced Cooling Operation ...............................................39

Wiring Error Check ..........................................................40

Saving Power Consumption ............................................40

Night Quiet Mode ............................................................41

Mode Lock.......................................................................42

Pcb Display(18/24k Model Only) .....................................43

Max Combination Capacity.................................................44

o Level gauge

o Screw driver

o Electric drill

o Hole core drill (ø50mm)

o Flaring tool set

o Specified torque wrenches

1.8kg.m, 4.2kg.m, 5.5kg.m, 6.6kg.m

(different depending on model No.)

o Adjustable wrench

o A glass of water

o Screw driver

o Hexagonal wrench(4mm)

o Refrigerant Gas Leak Detector

o Vacuum pump

o Gauge manifold

o Owner's manual

o Thermometer

o Remote Control Holder

Installation Requirements

Required Tools

4

Installation Parts Provided

[Ceiling Cassette Type]

Name

Quantity

Shape

for gas pipe

Conduit Bracket

Screw(M4) 2EA

for liquid pipe

Clamp metal

1 EA

Insulation for Remote

control holder

fitting

1 SET 1 EA

Drain hose

1 EA

Clamp

Conduit

Bracket

8 EA

Washer for

hanging backet

8 EA 1 EA

Installation Manual 5

Product Introduction

ENGLISH

h The figure can be changed according to model.

To prevent the injury of the user or other people and property damage, the following instructions

must be followed.

n Be sure to read before installing the air conditioner.

n Be sure to observe the cautions specified here as they include important items related to safety.

n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is

classified by the following indications.

n The meanings of the symbols used in this manual are as shown below.

WARNING

CAUTION

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

WARNING

n Installation

Be sure not to do.

Be sure to follow the instruction.

Safety Precautions

Always perform grounding.

• Otherwise, it may cause electri-

cal shock.

Don’t use a power cord, a

plug or a loose socket which

is damaged.

• Otherwise, it may cause a fire or

electrical shock.

For installation of the product,

always contact the service cen-

ter or a professional installation

agency.

• Otherwise, it may cause a fire,

electrical shock, explosion or in-

jury.

Securely attach the electrical

part cover to the indoor unit

and the service panel to the

outdoor unit.

• If the electrical part cover of the

indoor unit and the service panel

of the outdoor unit are not at-

tached securely, it could result in

a fire or electric shock due to

dust, water, etc.

Always install an air leakage

breaker and a dedicated

switching board.

• No installation may cause a fire

and electrical shock.

Do not keep or use flammable

gases or combustibles near

the air conditioner.

• Otherwise, it may cause a fire or

the failure of product.

Ensure that an installation frame of the out-

door unit is not damaged due to use for a long

time.

• It may cause injury or an accident.

Do not disassemble or repair the product ran-

domly.

• It will cause a fire or electrical shock.

6

Safety Precautions

Do not install the product at a place that there

is concern of falling down.

• Otherwise, it may result in personal injury.

Use caution when unpacking and installing.

• Sharp edges may cause injury.

Take the power plug out if

necessary, holding the head

of the plug and do not touch

it with wet hands.

• Otherwise, it may cause a fire

or electrical shock.

Do not use the power cord

near the heating tools.

• Otherwise, it may cause a fire

and electrical shock.

Do not open the suction

inlet of the indoor/outdoor

unit during operation.

• Otherwise, it may electrical

shock and failure.

Do not allow water to run

into electrical parts.

• Otherwise, it may cause the

failure of machine or electrical

shock.

Hold the plug by the head

when taking it out.

• It may cause electric shock

and damage.

Never touch the metal parts

of the unit when removing

the filter.

• They are sharp and may

cause injury.

Do not step on the

indoor/outdoor unit and do

not put anything on it.

• It may cause an injury through

dropping of the unit or falling

down.

Do not place a heavy object

on the power cord.

• Otherwise, it may cause a fire

or electrical shock.

When the product is sub-

merged into water, always

contact the service center.

• Otherwise, it may cause a fire

or electrical shock.

Do not share the outlet with

other appliances.

•

It will cause an electric shock or

a fire due to heat generation.

Do not use the damaged

power cord.

• Otherwise, it may cause a fire

or electrical shock.

Do not modify or extend the

power cord randomly.

• Otherwise, it may cause a fire

or electrical shock.

Take care so that the power

cord may not be pulled dur-

ing operation.

• Otherwise, it may cause a fire

or electrical shock.

Unplug the unit if strange

sounds, smell, or smoke

comes from it.

• Otherwise, it may cause elec-

trical shock or a fire.

Keep the flames away.

• Otherwise, it may cause a fire.

Take care so that children may not step on the outdoor unit.

• Otherwise, children may be seriously injured due to falling down.

n Operation

Use a vacuum pump or Inert (nitrogen) gas when doing leakage test or air purge. Do not compress air

or Oxygen and Do not use Flammable gases. Otherwise, it may cause fire or explosion.

•

There is the risk of death, injury, fire or explosion.

Installation Manual 7

Safety Precautions

ENGLISH

CAUTION

n Installation

Install the drain hose to ensure that drain

can be securely done.

• Otherwise, it may cause water leakage.

Install the product so that the noise or hot

wind from the outdoor unit may not cause

any damage to the neighbors.

• Otherwise, it may cause dispute with the neigh-

bors.

Always inspect gas leakage after the instal-

lation and repair of product.

• Otherwise, it may cause the failure of product.

Keep level parallel in installing the product.

• Otherwise, it may cause vibration or water leak-

age.

Avoid excessive cooling and perform venti-

lation sometimes.

• Otherwise, it may do harm to your health.

Use a soft cloth to clean. Do not use wax,

thinner, or a strong detergent.

• The appearance of the air conditioner may de-

teriorate, change color, or develop surface

flaws.

Do not use an appliance for special purposes

such as preserving animals vegetables, preci-

sion machine, or art articles.

• Otherwise, it may damage your properties.

Do not place obstacles around the flow inlet

or outlet.

• Otherwise, it may cause the failure of appliance

or an accident.

n Operation

8

Safety Precautions

Installation of Indoor, Outdoor Unit

Read completely, then follow step by step.

Indoor unit

1. Do not have any heat or steam near the unit.

2. Select a place where there are no obstacles in front of the unit.

3. Make sure that condensation drainage can be conveniently routed away.

4. Do not install near a doorway.

5. Ensure the unit is unobstructed, allow proper space on all sides according to the arrows and dis-

tance measurements in the figures.

6.

Use a Metal Detector or Metal Scanner to locate studs to prevent unnecessary damage to the wall.

Select the best location

Ceiling

Ceiling Board

Floor

Unit: inch(mm)

At least 70-

7

/8(1800)

141-

23

/32(3600) or less

39-

3

/

8

(1000)

or more

19-

11

/

16

(500)

or more

13

/

32

(10)

or more

19-

11

/16(500)

or more

11-

13

/16(300) or less

1-3/16(30)

1/8(±3)

[Ceiling Cassette Type]

Unit: inch(mm)

Installation Manual 9

Installation of Indoor, Outdoor Unit

ENGLISH

Outdoor unit

1. If an awning is built over the unit to prevent di-

rect sunlight or rain exposure, make sure that

heat radiation from the condenser is not re-

stricted.

2. Ensure the unit is unobstructed, allow proper

space on all sides according to the arrows

and distance measurements in the figures.

3. Do not place animals and plants in the path of

the warm air.

4. Take the air conditioner weight into account

and select a place where noise and vibration

are minimum.

5.

Select a place so that the warm air and sound

from the air conditioner does not disturb

neighbors.

Rooftop Installations:

If the outdoor unit is installed on a roof structure,

be sure to level the unit. Ensure the roof struc-

ture and anchoring method are adequate for the

unit location. Consult local codes regarding

rooftop mounting.

more than

27 9/16(700)

more than

11 13/16(300)

more than

23 21/32(600)

more than

11 13/16(300)

more than

23 21/32(600)

Unit: inch(mm)

10

Installation of Indoor, Outdoor Unit

Seaside Applications and Installation

1.

Air conditioners should not be installed in areas where corrosive gases, such as acid or alkaline gas, are

produced.

2. Do not install the product where it could be exposed to sea wind (salty wind) directly. It can result

corrosion on the product. Corrosion, particularly on the condenser and evaporator fins, could

cause product malfunction or inefficient performance.

3. If outdoor unit is installed close to the seaside, it should avoid direct exposure to the sea wind.

1) If the outdoor unit is to be installed close to the seaside, direct exposure to the sea wind should be avoided.

Install the outdoor unit on the opposite side of the sea wind direction.

2)

In case, to install the outdoor unit on the seaside, set up a windbreaker/barrier, to lessen the unit's exposure to sea air

3) Select a well-drained place.

• It should be strong enough (like concrete) to obstruct

the wind from the sea.

• The height and width should be more than 150% of

the outdoor unit.

• A minimum of 27 1/16 inches(70cm)

of space between outdoor unit and the windbreak

for easy air flow.

Sea wind Sea wind

Sea wind

Windbreaker/Barrier

Periodic ( more than once/year ) cleaning of the dust or salt particles stuck on the heat exchanger

using water is recommended.

1. Selecting the location(Outdoor Unit)

Installation Manual 11

Installation of Indoor, Outdoor Unit

ENGLISH

Seasonal Wind And Cautions In Winter

- Sufficient measures are required in a snow area or severe cold area in winter so that product can

be operated well.

- Get ready for seasonal wind or snow in winter even in other areas.

- Install a suction and discharge duct not to let in snow or rain.

- Install the outdoor unit not to come in contact with snow directly. If snow piles up and freezes on the

air suction hole, the system may malfunction. If it is installed at snowy area, attach the hood to the

system.

- Install the outdoor unit at the higher installation console by 50cm than the average snowfall (annual

average snowfall) if it is installed at the area with much snowfall.

- Where snow accumulated on the upper part of the Outdoor Unit by more than 10cm, always re-

move snow for operation.

1. The height of H frame must be more than 2 times the snowfall and its width shall not exceed the

width of the product. (If width of the frame is wider than that of the product, snow may accumulate)

2. Don't install the suction hole and discharge hole of the Outdoor Unit facing the seasonal wind.

12

Installation of Indoor, Outdoor Unit

Multi Piping Type

Piping length and elevation

h2

h1

A

B

Multiple Piping Type

CAUTION: Capacity is based on standard length and maximum allowance

length is on the basis of reliability.

Unit : ft(m)

24k 246(75) 82(25) 10(3) 49(15) 25(7.5) 33k

36k 246(75) 82(25) 10(3) 49(15) 25(7.5) 48k

Outdoor Unit

Capacity

(Btu/h class)

Max total length

of all pipes

(A+B)/(A+B+C)/

(A+B+C+D)

Max length of

each pipe

(A/B/C/D)

Min length of

each pipe

(A/B/C/D)

Max Elevation

between each

indoor unit and

outdoor unit (h1)

Max elevation

between indoor

units (h2)

Max.Combination

of Indoor unit

(Btu/h class)

Indoor unit Capacity (Btu/h class)

Pipe Diameter

Unit : inch(mm)

Gas Liquid

9, 12k 3/8(9.52) 1/4(6.35)

18k 1/2(12.7) 1/4(6.35)

Installation Manual 13

Installation of Indoor, Outdoor Unit

Distributor Piping Type

h1

C

Branch Pipe

Main Pipe

Distributor

A

B

h2

CAUTION: Capacity is based on standard length and maximum allowance

length is on the basis of reliability.

Unit : ft(m)

Outdoor Unit

Capacity

(Btu/h class)

Max total length

of all pipes

(Main + Branch

pipes)

Max length

of

Main pipe

(A+B+C)

Max length

of

Branch

pipes

Max length

of each

Branch pipe

Min length of

each pipe

(Main /

Branch

pipes)

Max Elevation

Between each

indoor unit and

outdoor unit

(h1)

Max Eleva-

tion

Between in-

door

(h2)

Max Combi-

nation

of indoor

unit

48k 476(145) 180(55) 295(90) 49(15) 10(3) 98(30) 49(15) 65k

ENGLISH

Indoor unit Capacity (Btu/h class)

Pipe Diameter

Unit : inch(mm)

Gas Liquid

9, 12k 3/8(9.52) 1/4(6.35)

18k 1/2(12.7) 1/4(6.35)

14

Installation

[Ceiling Cassette Type]

Ceiling dimension and hanging bolt location

Level gauge

Ceiling

Ceiling board

Unit: inch(mm)

23 1/16~26(585~660) (Ceiling Opening)

20 3/8(517)

18 5/32(461)

20 3/8(517)

23 1/16~26(585~660) (Ceiling Opening)

20 19/32(523)

22 15/32(570)

Unit Size

22 15/32(570)

Unit Size

12 9/16(319)

• The dimensions of the paper model for installation are the same as those of the ceiling opening dimensions.

• Avoid the following installation location.

1. Such places as restaurants and kitchen where considerable amount of oil steam and flour is generated.

These may cause heat exchange efficiency reduction, or water drops, drain pump mal-function.

In these cases, take the following actions;

• Make sure that ventilation fan is enough to cover all noxious gases from this place.

• Ensure enough distance from the cooking room to install the air

conditioner in such a place where it may not suck oily steam.

2. Avoid installng air conditioner in such places where cook-

ing oil or iron powder is generated.

3. Avoid places where inflammable gas is generated.

4. Avoid place where noxious gas is generated.

5. Avoid places near high frequency generators.

NOTICE

CAUTION :

• This air-conditioner uses a drain pump.

• Install the unit horizontally using a level

gauge.

• During the installation, care should be

taken not to damage electric wires.

• Select and mark the position for fixing bolts and piping

hole.

• Decide the position for fixing bolts slightly tilted to the

drain direction after considering the direction of drain

hose.

• Drill the hole for anchor bolt on the wall.

Use the ventilation fan

for smoke-collecting

hood with sufficient

capacity.

Cooking table

Air conditioner

Take enough

distance

Installation Manual 15

Installation

Set screw of

paper model (4 pieces)

Paper model

for installation

Ceiling board

5-7/8 inch

(150mm)

Ceiling board

Ceiling

Flat washer for M10

(accessory)

Keep the length of the bolt

from the bracket to 1-9/16 inch(40mm)

Open the ceiling board

along the outer edge of the

paper model

Flat washer for M10

(accessory)

Hanging bolt

(W3/8 or M10)

Nut

(W3/8 or M10)

Nut

(W3/8 or M10)

Spring washer

(M10)

Air Conditioner body

Keep the length of 1.22~1.34inch(31~34mm)

between the air conditioner bottom surfac

e and the ceiling surface

• The following parts are local purchasing.

① Hanging Bolt - W 3/8 or M10

② Nut - W 3/8 or M10

③ Spring Washer - M10

④ Plate Washer - M10

CAUTION : Tighten the nut and bolt to

prevent unit from falling off.

Wiring Connection

How to Fix

1(L1) 2(L2) 3 4 5

Terminal Block of Indoor Unit

Connected to outdoor unit

Ductless Ventilation Kit (DVKA,DVKB)

TO AIR

FRESH

KIT

TQ/TR series

Connecting Cable

Conduit

Screw

Conduit bracket

Conduit connection

• Remove the bushing rubber product attached on the indoor unit.

• Join the conduit and the conduit bracket together using nut.

• Set the connecting cable into the terminal block of indoor unit, and tighten set screw to lock the

conduit bracket to the indoor unit.

• Open the control box cover and connect the remote control cord and indoor power wires.

ENGLISH

16

Installation

Installation of Decorative Panel

The decorative panel has its installation direction.

Before installing the decorative panel, always remove the paper template.

1. Remove the packing and take out air inlet

grille from front panel.

2. Remove the Corner covers of the panel.

3. Fit the panel on the unit by inserting

hooks as shown in picture.

4. Insert two screws on diagonal corners of

panel. Do not tighten the bolts completely.

(The fixing screws are included in the in-

door unit box.)

Check the alignment of panel with the

ceiling. Height can be adjusted using

hanging bolts as shown in picture. Insert

the other two screws and tighten all

screws completely.

Front grille

Coner cover

Hook clip

Hook

Installation Manual 17

Installation

ENGLISH

5. Fit the corner covers.

6. Open two screws of control panel cover.

7. Connect one display connector and two

vane control connectors of front panel to

indoor unit PCB.

The position marking on PCB is as:

Display connector : CN-DISPLAY

Vane control connector: CN-VANE 1,2

8. Close the cover for control box.

9. Install the air inlet grille and Filter on the

panel.

Screw

CN-VANE 1,2

CN-DISPLAY

18

Installation

CAUTION:

Cool air leakage causes sweating.  Water drops fall.

Air conditioner

unit

Ceiling

board

Decorative panel

Decorative

panel

Fit the insulator (this part) and

be careful for cool air leakage

Good example

Air

Cool air leakage

(no good)

Bad example

Ceiling

board

Air conditioner unit

Flexible drain hose

HEAT INSULATION

1. Use the heat insulation material for the refrigerant piping which has an excellent heat-resis-

tance [over 248°F(120°C)].

2. Precautions in high humidity circum-

stance:

If it is operated for a long time in high

humid atmosphere [dew point tempera-

ture: more than 73.4°F(23°C)], water

drops are liable to fall. In this case, add

heat insulation material according to the

following procedure:

• Heat insulation material to be prepared... Adiabatic glass wool with thickness 10 to 20mm.

• Stick glass wool on all air conditioners that are located in ceiling atmosphere.

Indoor unit

Thermal insulator

(accessory)

Fastening band

(accessory)

Refrigerant piping

Installation Manual 19

Installation

ENGLISH

CAUTION : The supplied flexi-

ble drain hose should not be

curved, neither screwed. The

curved or screwed hose may

cause a leakage of water.

[Ceiling Concealed Duct/Ceiling Cassette Type]

• Drain piping must have down-slope (1/50 to 1/100): be

sure not to provide up-and-down slope to prevent rever-

sal flow.

• During drain piping connection, be careful not to exert

extra force on the drain port on the indoor unit.

• The outside diameter of the drain connection on the in-

door unit is 1 1/4 inch(32mm).

•

Be sure to install heat insulation on the drain piping.

Piping material: Polyvinyl chloride pipe inner

diometes 1 inch(Ø 25mm) and pipe fittings

• Connect the main drain pipe to the exterior and

leave it provisionally until the test comes to an

end.

• Feed water to the flexible drain hose and check

the piping for leakage.

• Be sure to check the drain pump for normal op-

erating and noise when electrical wiring is com-

plete.

• When the test is complete, connect the flexible

drain hose to the drain port on the indoor unit.

The air conditioner uses a drain pump to drain water.

Use the following procedure to test the drain pump operation:

Heat insulation material: Polyethylene foam

with thickness more than 5/16 inch(8mm).

Drain test

Maintenance

drain port

Upward

routing

not allowed

Pipe clamp

Indoor unit

1/50~1/100

Flexible drain hose

MAX : 700 mm(27 9/16 inch)

Feed water

Drain Pump

Drain pan

Flexible drain hose

(accessory)

Main

drain pipe

Glue the joint

Drain

port

Drain hose connection

Use the clip (accessory)

Flexible drain hose

1/50~1/100

Flexible drain hoseFlexible drain hoseFlexible drain hose

h The figure can be changed according to model.

Drain Piping

20

Installation

Attention

1. Possible drain-head height is up to 27 9/16

inch(700mm). So, it must be installed below

27 9/16 inch(700mm).

2. Keep the drain hose downward up to

1/50~1/100 inclination.

Prevent any upward flow or reverse flow in

any part.

3. 3/16 inch(5mm) or thicker formed thermal

insulator is provided for the drain pipe.

4. Upward routing is not allowed.

5. Be sure to check the drain pump for normal

operation and abnormal noise when electri-

cal wiring is complete.

1/50~1/100

MAX 27 9/16 inch

(700mm)

Elbow

Drain pump

Unit

Drain pipe

(Local supply)

Thermal insulator

(Local supply)

Wall

Drain hose

La page charge ...

Friedrich MR24DY3JMA Mode d'emploi

Ce manuel convient également à

Friedrich MR24DY3JMA Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents