Snom M10R KLE Quick Installation Guide

Marque: Snom

Modèle: M10R KLE

Taper: Quick Installation Guide

Ce manuel convient également à

M100 KLE

M100 KLE

SIP DECT 4-Line Base Sta� on

Quick Installa� on Guide

Hwang Jin wook | 09. Jan. 2019 | Revision 1.0Silkscreen artwork | M100 Base

Important Safety Information

This symbol is to alert you to important operating or servicing instructions

that may appear on the product or in this user’s manual. Always follow

basic safety precautions when using this product to reduce the risk of

injury, re, or electric shock.

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be

followed to reduce the risk of re, electric shock and injury, including the following:

1. This product should be installed by a qualied technician.

2. This product should only be connected to the host equipment and never directly

to the network such as Public Switch Telephone Network (PSTN) or Plain Old

Telephone Services (POTS).

3. Read and understand all instructions.

4. Follow all warnings and instructions marked on the product.

5. Unplug this product from the wall outlet before cleaning. Do not use liquid or

aerosol cleaners. Use a damp cloth for cleaning.

6. Do not use this product near water such as near a bath tub, wash bowl, kitchen

sink, laundry tub or swimming pool, or in a wet basement or shower.

7. Do not place this product on an unstable table, shelf, stand or other unstable

surfaces.

8. Slots and openings in the back or bottom of the base station and handset are

provided for ventilation. To protect them from overheating, these openings must

not be blocked by placing the product on a soft surface such as a bed, sofa or

rug. This product should never be placed near or over a radiator or heat register.

This product should not be placed in any area where proper ventilation is not

provided.

9. This product should be operated only from the type of power source indicated

on the marking label. If you are not sure of the type of power supplied at the

premises, consult your dealer or local power company.

10. Do not allow anything to rest on the power cord. Do not install this product

where the cord may be walked on.

11. Never push objects of any kind into this product through the slots in the base

station or handset because they may touch dangerous voltage points or create

a short circuit. Never spill liquid of any kind on the product.

12. To reduce the risk of electric shock, do not disassemble this product, but take it

to an authorized service facility. Opening or removing parts of the base station

or handset other than specied access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling can cause electric shock when

the product is subsequently used.

13. Do not overload wall outlets and extension cords.

14. Unplug this product from the wall outlet and refer servicing to an authorized

service facility under the following conditions:

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled onto the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the

operation instructions. Improper adjustment of other controls may

result in damage and often requires extensive work by an authorized

technician to restore the product to normal operation.

E. If the product has been dropped and the telephone base and/or

handset has been damaged.

F. If the product exhibits a distinct change in performance.

15. Avoid using a telephone (other than cordless) during an electrical storm. There

is a remote risk of electric shock from lightning.

16. Do not use the telephone to report a gas leak in the vicinity of the leak. Under

certain circumstances, a spark may be created when the adapter is plugged

into the power outlet, or when the handset is replaced in its cradle. This is a

common event associated with the closing of any electrical circuit. The user

should not plug the phone into a power outlet, and should not put a charged

handset into the cradle, if the phone is located in an environment containing

concentrations of ammable or ame-supporting gases, unless there is

adequate ventilation. A spark in such an environment could create a re or

explosion. Such environments might include: medical use of oxygen without

adequate ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.);

a leak of natural gas; etc.

17. Only put the handset of your telephone next to your ear when it is in normal talk

mode.

18. The power adapters are intended to be correctly oriented in a vertical or oor

mount position. The prongs are not designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or cabinet outlet.

19. Use only the power cord indicated in this manual.

20. For pluggable equipment, the socket-outlet shall be installed near the equipment

and shall be easily accessible.

21. In wall mounting position, make sure to mount the telephone base on the wall

by aligning the eyelets with the mounting studs of the wall plate. Then slide the

telephone base down on both mounting studs until it locks into place. Refer to

the full installation instructions in the User Manual.

22. CAUTION: Keep small metallic objects such as pins and staples away from the

handset receiver.

SAVE THESE INSTRUCTIONS

For cUL compliance only

Mesures de sécurité importantes

Ce symbole vous alertera d’informations importantes ou d’instructions

d’entretien pouvant apparaître dans ce guide d’utilisation. Respectez

toujours les mesures de sécurité et de sécurité de base lorsque vous

utilisez ce produit, an de réduire les risques de blessures, d’incendie,

ou d’électrocution.

Mesures de sécurité importantes

An de réduire les risques d’incendie, de blessures corporelles ou d’électrocution,

suivez toujours ces mesures préventives de base lorsque vous utilisez votre

téléphone

1. Cet appareil doit être installé par un technicien qualié.

2. Cet appareil doit être branché à un équipement hôte et jamais branché à un

réseau, tel qu’un réseau PSTN publique ou un réseau téléphonique standard

(POTS).

3. Lisez et comprenez bien toutes les instructions.

4. Observez toutes les instructions et mises en garde inscrites sur l’appareil.

5. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas

de nettoyeurs liquides ni en aérosol. N’utilisez qu’un chiffon doux et légèrement

humecté.

6. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un

évier de cuisine, d’un bac de lavage ou d’une piscine, ou dans un sous-sol

humide ou sous la douche.

7. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants.

L’appareil pourrait tomber et être sérieusement endommagé.

8. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées

à l’arrière ou en dessous. An d’empêcher la surchauffe, ces ouvertures ne

doivent pas être obstruées en plaçant l’appareil sur un lit, divan, tapis ou autre

surface similaires. Ne placez pas cet appareil à proximité d’un élément de

chauffage ni d’une plinthe électrique. De plus, ne l’installez pas dans une unité

murale ou un cabinet fermé qui ne possède pas d’aération adéquate.

9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les

étiquettes de l’appareil. Si vous ne connaissez pas le voltage de votre maison,

consultez votre marchand ou votre fournisseur d’électricité.

10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans

un endroit sécuritaire, là où personne ne pourra trébucher sur la ligne

d’alimentation ni le cordon téléphonique modulaire.

11. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car

ils pourraient toucher à des points de tension dangereux ou court-circuiter des

pièces, ce qui constituerait un risque d’incendie ou d’électrocution. N’échappez

pas de liquides dans l’appareil.

12. An de réduire les risques d’électrocution, ne démontez pas l’appareil, mais

apportez-le plutôt à un centre de service qualié s’il doit être réparé. En

enlevant le couvercle, vous vous exposez à des tensions dangereuses ou

autres dangers similaires. Un remontage inadéquat peut être à l’origine d’une

électrocution lors d’une utilisation ultérieure de l’appareil.

13. Ne surchargez pas les prises de courant ni les rallonges électriques, car ceci

peut constituer un risque d’incendie ou d’électrocution.

14. Débranchez cet appareil de la prise de courant et communiquez avec le

département de service à la clientèle de Snom dans les cas suivants:

A. Lorsque le cordon d’alimentation est endommagé ou écorché.

B. Si du liquide a été échappé dans l’appareil.

C. Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.

D. Si l’appareil ne fonctionne pas normalement en suivant les directives du

guide. N’ajustez que les commandes couvertes dans le guide d’utilisation,

car un mauvais réglage de celles-ci peut être à l’origine de dommages, ce

qui nécessiterait des réparations considérables pour remettre l’appareil à

son état de fonctionnement normal.

E. Si l’appareil a été échappé ou son boîtier, endommagé.

F. Si le produit afche une nette diminution de sa performance.

15. Évitez d’utiliser un téléphone (autre qu’un sans l) pendant un orage. Les éclairs

peuvent être à l’origine d’une électrocution.

16. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de

celle-ci. Sous certaines circonstances, une inteincelle pourrait survenir lorsque

l’adaptateur est branché à une prise de courant, ou lorsque le combiné

est déposé sur le combiné. Ceci est un événement commun associé avec

la fermeture d’un circuit électrique. L’utilisateur ne devrait pas brancher le

téléphone dans une prise de courant, et ne devrait pas déposer le combiné

chargé sur le socle, si le téléphone se trouve dans un environnement ou la

concentration de gaz inammables, sans ventilation adéquate. Une étincelle

dans ces endroits pourrait provoquer un incendie ou une explosion. Ces

environnements pourraient être l’utilisation médicale de l’oxygène sans

ventilation adéquate; le gaz industriel (dissolvants, vapeurs d’essence, etc.);

une fuite de gaz naturel, etc.

17. Placez uniquement le combiné de votre appareil près de votre oreille lorsqu’il

est en mode de conversation normal.

18. Les adaptateurs sont conçus pour être orientés en position verticale ou en

position horizontale sur le plancher.

19. N’utilisez que cordon d’alimentation et les piles indiquées dans ce guide

d’utilisation.

20. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise

de courant doit être installée près du produit, an d’assurer une accessibilité

sécuritaire à la prise de courant.

21. En position de montage mural, assurez-vous de monter le socle du téléphone

sur le mur en alignant les oeillets avec les goujons de xation de la plaque

murale. Ensuite, faites glisser le socle vers le bas sur les deux goujons de

xation jusqu’à ce qu’il se verrouille en place. Reportez-vous aux instructions

complètes dans la section Installation dans ce guide d’utilisation.

22. MISE EN GARDE : Éloignez les petits objets métalliques tels que les broches

de l’écouteur du combiné.

CONSERVEZ CES INSTRUCTIONS

Compliance

FCC part 15

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at the user’s expense.

Privacy of communications may not be ensured when using this phone.

Warning: Changes or modications to this equipment not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

Caution: To maintain the compliance with the FCC’s RF exposure guideline, place the

base unit at least 20 cm from nearby persons.

For body-worn operation, this handset has been tested and meets the FCC RF exposure

guidelines when used with the accessories supplied or designated for this product. Use of

other accessories may not ensure compliance with FCC RF exposure guidelines.

Industry Canada

This Class A digital apparatus complies with Canadian requirements:

CAN ICES-3 (A)/NMB-3(A). Cet appareil numérique de la classe A est conforme à la

norme CAN ICES-3 (A)/NMB-3(A) du Canada.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with

Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

Privacy of communications may not be ensured when using this telephone.

The term ‘’IC:‘’ before the certication/registration number only signies that the

Industry Canada technical specications were met.

This product meets the applicable Innovation, Science and Economic Development

Canada technical specications.

Parts Checklist

Your package contains the following items. Save your sales receipt and

original packaging in the event warranty service is necessary.

About this Guide

This quick installation guide provides a reference for the external features of the

base station and basic installation instructions.

Please refer to the M100 KLE SIP DECT 4-Line Base Station Administrator and

Provisioning Manual for complete conguration instructions.

For customer service or product information, visit our website at

www.snomamericas.com .

Quick Installation

Guide

AC adapter

Base Station

wall-mounting plate

Ethernet cable

Quick start guide

VDP650

Hwang Jin wook | 09. Jan. 2019 | Revision 1.0Silkscreen artwork | M100 Base

illustration scale 40%

Hwang Jin wook | 09. Jan. 2019 | Revision 1.0CSP | M100 Base

PART DESCRIPTION COLOR/MATERIAL TEXTURE/FINISH

01. Left Housing SPI B-1Graphite Spray

02. Right Housing SPI B-1Graphite Spray

03. Lens SPI B-1Clear Acrylic Lens

Silkscreen on the rear ( Background ) Pantone Black C

Silkscreen on the rear ( , , ) - Pantone Coolgray 3C

Silkscreen on the rear ( , ) - Milky White / Green Backlight

Silkscreen on the Top ( ) - Pantone 8001C

04. Middle Housing SPI A-1

MT-11520

Injection Moulded - ChiMei PA-757 J01 (Snom standard black)

05. Antenna Back Housing MT-11520Injection Moulded - ChiMei PA-757 J01 (Snom standard black)

06. Antenna Front Housing SPI B-1Graphite Spray

08. Bottom Cover SPI B-1

MT-11520

Injection Moulded - ChiMei PA-757 J01 (Snom standard black)

09. Wall Mount Injection Moulded - ChiMei PA-757 J01 (Snom standard black)

07. Chrome Key SPI A-1

SPI A-1

TL92278BT

Chrome Plating ( without Top Surface )

Engraving -0.3mm ( ) High Glossy Chrome

Top Surface

M100 KLE

Hwang Jin wook | 09. Jan. 2019 | Revision 1.0Silkscreen artwork | M100 Base

Quick Reference Guide

Base station external features

Reset button

Press for

15 seconds to

restore factory

defaults. If the reset

is successful, the

LED will ash

slowly.

AC adapter input

Ethernet port

Front Rear

Handset Locator

(Page) button

Press to ring the cordless

accessories

Press and hold to register

cordless accessories.

LED (Power)

Flashes when joining the

network or when registering/

deregistering a cordless

accessory.

Steady when power is

connected and an

IP address is acquired.

Antenna

LED

Flashes when registering/

deregistering a cordless

accessory.

Steady when all SIP accounts

are registered.

Off when a SIP account is not

registered.

Base Station Installation

This section assumes that your network infrastructure is established and that your

IP PBX phone service has been ordered and congured for your location.

For more information about IP PBX conguration, see the

M100 KLE SIP DECT 4-Line Base Station Administrator and Provisioning Manual.

You can power the base station using the supplied power adapter or using Power over

Ethernet (PoE) from your network. (The base station requires PoE Class 2.)

If you are not using PoE, install the base station near a power outlet not controlled by a

wall switch. The base station can be placed on a at surface or mounted on a wall in a

vertical or horizontal orientation.

Avoid placing the base station too close to:

• Communication devices such as television sets, DVD players, or other cordless

telephones

• Excessive heat sources

• Noise sources such as a window with trafc outside, motors, microwave ovens,

refrigerators, or uorescent lighting

• Excessive dust sources such as a workshop or garage

• Excessive moisture

• Extremely low temperature

• Mechanical vibration or shock such as on top of a washing machine or work bench

Note: For cordless accessory installation, see the M10 KLE SIP DECT 4-Line Handset

Quick Installation Guide and the M18 KLE SIP DECT 4-Line Deskset Quick

Installation Guide.

To install the base station:

1. Plug one end of the Ethernet cable into the Ethernet port on the rear of the base

station (marked by ), and plug the other end of the cable into your network

router or switch.

2. If the base station is not using power from a PoE-capable network router or switch:

a. Connect the supplied power adapter to the base station power jack.

b. Plug the power adapter into an electrical outlet that is not controlled by a wall

switch.

Use only

Supplied

Adapter

RESET

IMPORTANT INFORMATION

1. Use only the power adapter supplied with the product. To order a replacement

power adapter, visit our website at www.snomamericas.com .

2. The power adapter is intended to be correctly oriented in a vertical or oor mount

position. The prongs are not designed to hold the plug in place if it is plugged into

a ceiling, under-the-table or cabinet outlet.

To mount the base station on a wall:

1. Install two mounting screws on the wall. Choose screws with heads larger

than 5 mm (3/16 inch) in diameter (1 cm / 3/8 inch diameter maximum).

The screw centers should be 5 cm (1 15/16 inches) apart vertically

or horizontally.

2. Tighten screws until only 3 mm (1/8 inch) of the screws

are exposed.

3. Attach the mounting plate to the top of the base station. Insert the tab into the slot

and then push the plate in at the bottom of the base station until the mounting plate

clicks into place.

4. Check to make sure the plate is secure at top and bottom. It should be ush with

the base station body.

5. Place the base station over the mounting screws.

6. Connect the Ethernet cable and power as described in “To install the base station.”

Insert tab into slot.

Maintenance

Taking care of your product

• Your base station contains sophisticated electronic parts, so you must treat it

with care.

• Avoid rough treatment.

• Save the original packing materials to protect your product if you ever need to

ship it.

Avoid water

• You can damage your base station if it gets wet. Do not use cordless accessories

in the rain, or handle them with wet hands. Do not install the base station near a

sink, bathtub or shower.

Electrical storms

• Electrical storms can sometimes cause power surges harmful to electronic

equipment. For your own safety, take caution when using electric appliances

during storms.

Cleaning your product

• Your product has a durable plastic casing that should retain its luster for many

years. Clean it only with a soft cloth slightly dampened with water or a mild soap.

• Do not use excess water or cleaning solvents of any kind.

Remember that electrical appliances can cause serious injury if used when you

are wet or standing in water. If the telephone base should fall into water, DO NOT

RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD FROM THE WALL, then

pull the unit out by the unplugged cord.

Technical Specications

RF frequency band 1921.536–1928.448 MHz

Channels 5

Operating temperature 32–104 °F (0–40 °C)

Power requirements 5.0Vdc @ 800mA

Power over Ethernet IEEE 802.3at supported, class 2

Ethernet network port 10/100 Mbps RJ-45 port

VTECH COMMUNICATIONS, INC.

Tigard, Oregon 97223, USA.

v2019002 Version 2, 06/19

Snom M10R KLE Quick Installation Guide

Marque: Snom

Modèle: M10R KLE

Taper: Quick Installation Guide

Ce manuel convient également à

M100 KLE

Télécharger le PDF

rapport

dans d''autres langues

English: Snom M10R KLE

Snom M10R KLE Quick Installation Guide

Ce manuel convient également à

Snom M10R KLE Quick Installation Guide

dans d''autres langues

Documents connexes