Lynx Fire Pit Manuel utilisateur

Lynx
Marque
Lynx
Modèle
Fire Pit
Taper
Manuel utilisateur
MAKE THE MOST OF YOUR
SEDONA
BY
TM
Warning: Improper installation, adjustment, alteration. Service or maintenance can cause severe injury or death, and may result in prop-
erty damage. Read these installation, operating and maintenance instructions thoroughly before installing or servicing this appliance.
INSTALLER: THIS MANUAL MUST BE LEFT WITH THE APPLIANCE.
CONSUMER: KEEP THIS MANUAL FOR FUTURE USE.
CARE & USE/ICE ‘N FIRE PIT INSTALLATION
2
|
Care & use/ FIre PIT InsTallaTIon
WARNINGS
READ THIS MANUAL CAREFULLY AND COMPLETELY BEFORE USING YOUR OUTDOOR APPLIANCE TO
REDUCE THE RISK OF:
1. Fire
2. Burn hazard, personal injury or property damage
3. Unapproved installation or servicing.
THIS PRODUCT IS DESIGNED FOR OUTDOOR USE ONLY. Improper installation, adjustment, alteration, service
or maintenance can cause property damage, injury or death.
Read this manual thoroughly before installation, use, or servicing of this product.
1. The burning of gaseous fuel generates some by-products which are on the list of substances which are
known by the State of California to cause cancer or reproductive harm.
2. California law requires businesses to warn customers of potential exposure to such substances. To minimize
exposure to the substances, always operate this unit according to the use and care instructions found in this
manual. Be certain to provide adequate ventilation when in operation
IF YOU SMELL GAS:
1. Shut off all gas supply lines to the appliance.
2. Extinguish any open flames.
3. If odor continues, keep everyone away from
the appliance and immediately call your gas
supplier or your fire department.
1. DO NOT store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
2. An LP cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
S’IL Y A UNE ODEUR DE GAZ:
1. Coupez l’admission de gaz de l’appariel.
2. Éteindre toute flamme nue.
3. Si l’odeur persiste, èloignez-vous de
l’appareil et appelez immèdiatement le
fournisseur de gaz ou le service d’incendie.
1. Ne pas entreposer ni utiliser de l’essence ni
d’autres vapeurs ou liquides inflammables
dans le voisinage de l’appareil, ni de tout
autre appareil.
2. Une bouteille de propane qui n’est pas rac-
cordée en vue de son utilisation, ne doit pas
être entreposée dans le voisinage de cet
appareil ou de tout autre appareil.
WARNING
DANGER
WARNING
DANGER
AVERTISSMENT
Warning! CALIFORNIA PROPOSITION 65
SEDONA
Care & use/ FIre PIT InsTallaTIon
|
3
WARNINGS
WARNING
To obtain replacement parts or service contact:
Lynx Grills
7300 Flores Street
Downey, CA 90242
888-289-5969
•Never use dented, rusty or damaged propane cylinders. Never store additional or empty propane
cylinders in the cabinet or in the vicinity of this or any other appliance. Do not store propane cylinders
indoors or on their sides.
•Children should NEVER BE LEFT ALONE or unattended in an area where an appliance is located. Place
your appliance well away from areas where children play. Do not store items that may interest children in
or around the area of your appliance, in your appliance cart, or in the enclosure.
•Never move the appliance when hot. When in use, portions of the appliance are hot enough to cause
severe burns.
•Always maintain the required clearances from combustibles as detailed. These appliances are designed for
outdoor use only. Never use in a garage, building, shed, breezeway, or other enclosed area. Do not use
this equipment under any overhead combustible construction.
•Fire pits are not designed or certified for and are not to be installed in or on recreational vehicles, portable
trailers, boats or any other moving installation.
•Always have an ABC Fire Extinguisher accessible.
•STORING YOUR appliance: Store your appliance in a well-ventilated area. If stored indoors, detach and
leave L.P. cylinder outdoors in a well-ventilated area away from heat and away from where children may
tamper with it.
•Do not repair or replace any part of the appliance unless specifically recommended in this manual. Other
service should be performed by a qualified technician.
•If the appliance is installed by a professional installer or technician, be sure that he/she shows you where
your gas supply shut-off is located. All gas lines must have a shut-off that is readily and easily accessible.
If you smell gas, check for gas leaks immediately. Check only with a soap and water solution. (See SAFETY
PRECAUTIONS on page 8 for further details.) Never check for gas leaks with an open flame.
•Inspect the LP gas supply hose prior to each use of the appliance. If there is evidence of excessive abrasion
or wear, or the hose is cut, it must be replaced before using the appliance.
THIS MANUAL MUST REMAIN WITH THE PRODUCT OWNER FOR FUTURE REFERENCE.
Part No. 34776 03/2014
4
|
Care & use/ FIre PIT InsTallaTIon
WARNINGS
STATE OF MASSACHUSETTS
DANGER
1. Massachusetts requires all gas be installed using a plumber or gas fitter carrying the appropriate
Massachusetts license.
2. All permanently-installed natural gas or propane installations require a “T” handle type manual gas valve be
installed in the gas supply line to this appliance.
3. This does not apply to portable propane installations using a 20 pound cylinder.
1. This appliance produces carbon monoxide which has no odor.
2. Using this appliance in an enclosed space can cause death.
3. Never use this appliance in an enclosed space. Never use in a garage, building, shed, breezeway, or other
enclosed area.
WARNING
1. This outdoor appliance and its individual shutoff valve must be disconnected from the gas supply piping
system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa).
2. This outdoor appliance must be isolated from the gas supply piping system by closing its individual manual
shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less
than 1/2 psi (3.5 kPa).
Prior to assembly of your new Lynx Ice ‘N Fire Pit you may want to consider the location of the fire pit. Do you
have prevailing winds which may effect the burner operation? Is the ground you plan on installing the fire pit
level and firm? Do you have an assistant to help with positioning the fire pit and table top. The table top may
be heavy and awkward to handle alone.
Before you can use the fire pit you must install the table top on the fire pit base, and install the burner assem-
bly to the table top. The LP gas tank must be installed and connected properly to the burner assembly and the
controls connected for proper operation.
Please read these instructions carefully and completely before proceeding. Incorrect installation and assembly
may result in fire, damage or personal injury or death.
SEDONA
Care & use/ FIre PIT InsTallaTIon
|
5
IMPORTANT SAFETY PRECAUTIONS
PLEASE REVIEW THESE IMPORTANT SAFETY
PRECAUTIONS BEFORE YOU USE YOUR FIRE PIT.
1. NEVER LEAVE THE FIRE PIT UNATTENDED WHILE IN USE.
2. Follow the instructions in this manual carefully to reduce the risk or personal injury, death or property loss.
3. Ensure all tie-down wires have been removed from the burners.
4. Always use caution when operating the appliance in a windy area.
5. Avoid wearing loose-fitting garments or long sleeves while adjusting fire pit media. They could ignite.
6. Never touch the appliance rocks or immediate surrounding surfaces with your bare hands while in operation.
7. Use only the type of fuel specified on the appliance rating plate. Verify the fuel gas is correct and the proper
pressure is available. Never use wood, charcoal or any other solid fuel or liquid fuel in this fire pit. Conversion
kits are available from the manufacturer if natural gas use is desired. Contact Lynx customer care.
8. Never replace the appliance rocks with any other material such as granite, marble or any other dense stone as
these may crack or burst under flame and heat. The units are shipped for use with LP gas.
9. Do not use the appliance unless a leak check has been performed on all gas connections.
10. Never operate the appliance while under the influence of alcohol or drugs.
11. Do not lean or sit on table shelves and never place a load weighing more than 25 pounds on the shelf.
12. If the burner does not light or goes out during operation, turn off all gas control knobs and wait five (5) minutes
before attempting to re-light.
6
|
Care & use/ FIre PIT InsTallaTIon
STEP 1: Unpack the table top and the base. Remove all packing materials, tie down straps and any other packaging.
STEP 2: Place the fire pit base on a flat firm surface. The Fire Pit must be on solid ground or pavers so it will not sink over time.
STEP 3: With the help of an assistant, place the table top on top of the base, making sure the table top is centered properly.
SEDONA FIRE PIT ASSEMbLY INSTRUCTIONS
Burner and IgnItIon Controls
Install burner and burner pan in the table top opening. This can be accomplished In one or two ways.
Before dropping the burner pan into the enclosure, connect the LP hose to the LP cylinder, and the ignition wire from
the igniter module to the power button.
As an alternative you can install the burner pan into the table top, and working from the base access door, connect the
LP hose to the LP Tank, connect igniter module to the power button.
Do not add the burner media until you check the spark ignition in the next step.
Ignition Wire Connector
STEP 1
9 volt battery
Care & use/ FIre PIT InsTallaTIon
|
7
Press the ignition button and verify a spark is present at
the spark electrode at the burner assembly. If you do not
see or hear a spark, please refer to the trouble shooting
section of this manual.
If the ignition spark is present, proceed to the next step,
addition of burner media.
Media installation
bURNER AND IGNITION CONTROLS ...continued
STEP 2
STEP 1: Install the burner pan as described above
STEP 2: Add lava rocks and spread evenly to cover the entire burner assembly, and an additional ½ - 1” deep. Be careful
not to block the ignition box openings as this will affect proper ignition. Be careful not to bury the burner pan handle.
STEP 3: Add river rocks in a single layer, to cover the lava rock. The ignition box may be loosely covered with the river
Your Ice ‘N Fire Pit needs burner media in order to create realistic, natural looking flame effects. Follow the instructions
outlined below to create safe and pleasing fire effects.
InstallIng the lP CylInder
The LP Gas cylinder, or tank, must comply with U.S Department of Transportation (D.O.T.) Specifications for
LP Gas Cylinders or the Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods
and Commission CAN/CSA-B339. The cylinder must be protected with a listed overfill prevention device and
provided with a connection device compatible with the appliance connector. Failure to meet this requirement
may create a hazardous condition resulting in personal injury, death or damage to personal property, and may
pose a risk of fire or explosion.
WARNING
8
|
Care & use/ FIre PIT InsTallaTIon
INSTALLING THE LP CYLINDER...continued
The LP tank is brought into the fire pit enclosure and
secured to the square base frame by the bottom ring of
the cylinder.
Connect the LP hose and regulator assembly to the LP
Cylinder. Do not use tools when making this connection,
the knob must be hand tightened only.
Rotate the burner pan until the gas valve lines up with
the opening for the gas valve key. Make sure the burner
control valve is in the OFF position before opening the
cylinder valve.
STEP 1
STEP 2
Safety PrecautionS
Inspect the LP gas hose and connections before each use. If there is any damage from normal operating conditions,
weather, rodents or other adverse conditions do not use the hose. Turn OFF the LP tank valve and replace the hose and
regulator assembly. Replacement parts are available from the Lynx Grills, Inc..
Before using your fire pit you must test all gas connections to ensure leak-free connections. Gas connections can be
tested with a solution of 1 part dish soap to 3 parts water. Turn on gas at the cylinder gas valve. Brush or spray the solu-
tion on all connections and look for the formation of bubbles. NEVER USE AN OPEN FLAME TO CHECK FOR LEAKS.
If you find any leaks, tighten the connections and retest. If you cannot stop the leak, turn off the gas at the cylinder gas
valve and call a qualified repair technician, or contact Lynx Grills to arrange a service call.
Inspect the burner assembly regularly for damage. Clean any blocked ports. Be aware that insects like to make webs
inside burner assemblies and hoses.
LP Tank Bottom Collar
Support
Line up gas valve with
key control opening
Care & use/ FIre PIT InsTallaTIon
|
9
LIGHTING INSTRUCTIONS
STEP 1: Make sure the gas shut-off valve on the LP Tank is in the open position
STEP 2: Start the spark igniter by pressing the ignition button. The starter will stay on until the button is pressed again.
STEP 3: Using the Gas Valve Key, open the gas burner control
valve through the opening in the control panel. Turn the key to the
left (counter-clockwise) until it is full open. The burner should light
immediately. If the burner does not light in 4 seconds, turn the gas valve
OFF, push the ignition button to turn off the igniter, Wait 5-minutes for
any gas to dissipate, then repeat steps 2 and 3 again. If the burner fails
to light contact Lynx Customer Care.
STEP 4: After the burner lights push in the ignition button to shut off
the ignition module.
STEP 5: Use the gas valve key to adjust the flame to a comfortable level.
DO NOT LEAVE A LIT FIRE-PIT UNATTENDED!
Shutting Down the Fire Pit
STEP 1: Using the Gas Valve Key Turn off the gas to the burner by turning the Key to the right (clockwise) until the
valve is fully closed
STEP 2: Shut OFF the LP tank gas valve
Converting to a Beverage Holder
You new Lynx Fire Pit is easily converted into an icy beverage holder for those warm days when a fire pit Is not needed.
STEP 1: Shut off gas from the LP Cylinder and remove the LP Hose
STEP 2: Disconnect the ignition wire at the connector
STEP 3: Lift out the burner pan using the convenient handle
STEP 4: Insert the Ice pan into the cutout opening
STEP 5: Fill with ice and your favorite beverages and enjoy.
Trouble ShooTing
1. Make sure a fresh 9 volt battery has been installed
2. Make sure all wire connectors are firmly attached. They may have come loose in shipping
3. Check to see that the LP tank is full and properly connected.
If you have any problems or concerns, please contact Lynx Customer care
Lynx Grills, Inc.
7300 Flores Street
Downey, CA 90242
888-289-5969
10
|
Care & use/ FIre PIT InsTallaTIon
REFRESHMENT BOWL CONVERSION
44.00
TOP VIEW
TOP VIEW
FRONT VIEW
44.00
22.00
22.00
FIRE/REFRESHMENT
BOWL
44.00
44.00
24.00
28.00
44.00
TOP VIEW
TOP VIEW
FRONT VIEW
44.00
22.00
22.00
FIRE/REFRESHMENT
BOWL
44.00
44.00
24.00
28.00
44.00
TOP VIEW
TOP VIEW
FRONT VIEW
44.00
22.00
22.00
FIRE/REFRESHMENT
BOWL
44.00
44.00
24.00
28.00
FEATURES
PERFORMANCE
TECHNICAL
ACCESSORIES
PRODUCT DIMENSIONS
Model No. LFPC-S & LFPC-G. LFPS-S & LFPS-G
Tumbled volcanic variegated stone.
Access door provides easy accessibility to LP Tank and battery compartment.
65,000 BTU max.
Fuel Type: LP Standard / NG Kit available.
Electric pushbutton ignition with manual valve for flame setting.
NG Conversion Kit available.
Caster Kit available.
Vinyl Cover (included).
Overall diameter 44"
Overall height approx. 24"
2. Place refreshment bowl
into top
1. Remove gravel pan
from top
3. Refreshment bowl
44” round top on round pedestal with unique
nautilus burner.
44” square top on round pedestal with unique
nautilus burner.
Care & use/ FIre PIT InsTallaTIon
|
11
1
14
11
9
22
17
16
15
3
8
4
5
12
2
217
6
13
10
ITEM PART No. DESCRIPTION QTY.
1 80884 FIREPAN WELDMENT 1
2 34641 NAUTILUS BURNER 1
3 34640 IGNITER SHIELD 1
4 31217 SPARK ELECTRODE, 15" 1
5 34654 BRACKET, BURNER RETAINER 2
6 34644 HANDLE, PAN 1
7 34652 KEY VALVE, FIREPIT 1
8 31162 IGNITOR, 2 SPARK 1
9 70231 BATTERY HOLDER 1
10 34773 MOLEX PLUG, PANEL MOUNT 1
11 34774 LOCK NUT, ELECT., 3/4"-14 NPSM 2
12 34775 COTTER PIN, .093 X .750 2
13 31582 UNION COUPLER, 1/2" NPT 1
14 34695 ORIFICE, VENTED, #41 1
15 14030 SCREW, 1/4-20 X 1/2, HHD, SS 2
16 31876 NUT, 1/4-20, LKN, STEEL, W/ESL 2
17 33706 SCREW, #10-32 X 3/8, PHP, SS 2
18 32768 NUT, #10-32, INSERT, STEEL, ZINC 2
19 80661 WIRE, GROUND, 16" 1
20 70230 WIRE, IGNITION, 6" 1
21 13012 NIPPLE, 1/2 CLOSE BLACK 1
22 13054 ELBOW, 3/8" FLARE TO 1/2^ FIP 1
23 30751 SCREW, #6-32 X 1/2, FHP, SS 2
24 70232
ICE BOWL
1
25 80883
BURNER PAN ASSEMBLY
1
1
25
12
|
Care & use/ FIre PIT InsTallaTIon
Care & use/ FIre PIT InsTallaTIon
|
13
SEDONA bY LYNX ICE N’ FIRE PIT LIMITED WARRANTY
I. Limited Twelve-Year Warranty.
The Nautilus stainless steel main burner carries a limited
twelve (12) year warranty. This warranty excludes surface
corrosion, scratches, and discoloration which may occur
during normal use. This warranty is limited to the replacement
of the defective parts, with the owner paying all other cost
including labor, shipping and handling.
II. Limited Five-Year Warranty.
The following parts are warranted to be free from defects
in material and workmanship, when subjected to normal
domestic use and service, for a period of five (5) years from
the original date of purchase; burner pan, manifolds and
gas valves. This warranty is limited to the replacement of
the defective parts, with the owner paying all other costs
including labor, shipping, and handling.
III. Limited Two-Year Warranty
All other components are warranted to be free from defects
in material and workmanship, when subjected to normal
domestic use and service, for a period of two (2) years from
the original date of purchase. This warranty is limited to the
replacement of the defective parts, with the owner paying all
other costs including labor, shipping and handling.
IV. Limited One-Year Warranty.
For a period of one (1) year from the original date of
purchase, Lynx will replace or repair parts found to be
defective at no cost to the original purchaser. This includes
the cost of shipping replacement parts and, where necessary,
service labor at prevailing local rates by a Lynx authorized
service person. Service will be provided during normal
business hours and must be authorized in advance by Lynx.
V. Limitations & Exclusions
1) This Warranty shall apply to products purchased and
located in the United States and Canada. Products must
be purchased in the country where service is requested.
2) Warranty applies only to the original purchaser and may
not be transferred.
3) Warranty is in lieu of all other warranties expressed or
implied and all other obligations or liabilities related to the
sale or use of its grill products.
4) Warranty shall not apply and Lynx is not responsible
for damage resulting from misuse, abuse, alteration
of or tampering with the appliance, accident, hostile
environment, flare-up fires, improper installation, or
installation not in accordance with the instructions
contained in this manual, or the local codes.
5) Lynx shall not be liable for incidental, consequential,
special or contingent damages resulting from its breach of
this written warranty or any implied warranty.
6) Some states do not allow limitations on how long an
implied warranty lasts, or the exclusions of or limitations on
consequential damages. This warranty gives you specific
legal rights and you may have other rights which vary from
state to state.
7) No one has the authority to add to or vary Lynx’s warranty,
or to create for Lynx any other obligation or liability in
connection with the sale or use of its products.
8) Limited to the replacement of defective parts with the
owner paying all other costs including labor.
VI. What is not covered: Lynx shall not be responsible for and
shall not pay for the following:
1) Installation or start-up, damages or problems caused by
improper installation or use;
2) Service by an unauthorized service provider;
3) Damage or repair due to service by an unauthorized
service provider or use of unauthorized parts;
4) Warranty does not apply to products installed in any
commercial or non-residential application. Examples of
excluded applications include, but are not limited to day
care centers, schools, bed and breakfast centers, churches,
private clubs, fire stations, club houses, common areas in
multi-family dwellings, restaurants, hotels, nursing homes,
food service locations and institutional food service
locations.
5) To correct normal adjustments or settings, due to
improper installation, commissioning or local gas supply
properties.
6) Shipping and handling costs, export duties, installation,
removal, or re-installation cost.
7) Display models are sold “as is”. If you have purchased
a display model, please be advised that it is sold “as is”
and that it is subject to the following warranty exclusions:
any exterior or cosmetic damage is nonwarrantable;
any missing components will be replaced at consumers
expense; major handling damage to manifold, valve and
ignition system will be serviced at consumer’s expense; all
other warranty’s (standard warranty) will remain in effect.
8) The cost of a service call to diagnose trouble.
Lynx Grills
7300 Flores Street
Downey, CA 90242
Service: (888) Buy-Lynx (888-289-5969)
Fax: (562) 299-6978
www.lynxgrills.com
SEDONA
BY
TM
PN #34776 RevC, 03/2014
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Lynx Fire Pit Manuel utilisateur

Lynx
Marque
Lynx
Modèle
Fire Pit
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents