Marvel MO24RD Mode d'emploi

Marque: Marvel

Modèle: MO24RD

Taper: Mode d'emploi

Outdoor Refrigerated Drawers

Tiroirs réfrigérés d' extérieur

MO24RD

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

NOTE

CAUTION

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti-tip device .................................................6

Energy saving tips ..............................................................7

Product dimensions ............................................................8

Using your Electronic control ............................................10

Starting your appliance ..................................................10

Turning your appliance "ON" or "OFF" ..........................10

Adjusting the temperature .............................................10

Refrigerator operation ...................................................10

Alarms ...........................................................................10

Door (drawer) ajar.....................................................10

Temperature sensor fault...........................................10

High and Low temperature .......................................10

Alarm mute ...................................................................11

Care and cleaning .............................................................11

Long term storage / winterization .................................12

Stainless steel maintenance ............................................13

Obtaining service .............................................................13

Troubleshooting ................................................................14

Warranty ...........................................................................15

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

CONTENTS

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

NOTE

CAUTION

WARNING

XXXXXXXXXXXX

MARVEL

UNPACKING YOUR APPLIANCE

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.marvelrefrigeration.com.

The following information will

be required when registering

your appliance.

Service Number

Rev. Letter

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on

the serial plate which is located inside the cabinet on the

bottom of the liner toward the left side. Open the bottom



Warranty Registration

Online registra-

tion available at

www.marvelrefrig-

eration.com

Figure 1

WARNING

WARNING - Help Prevent Tragedies



the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• 

• Leave the shelves in place so children may not

easily climb inside.

WARNING

WARNING - Dispose of the plastic bags which can



CAUTION

Figure 2

Front Leveling

Legs

Front Grille,

keep this area

open.

Rear

Leveling

Legs

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

-

mended installation location temperature range is from 55

to 115°F (13 to 46°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unobstruct-

ed.

Front Grille

Do not obstruct the front grille. The openings within the

-



energy usage and loss of cooling capacity. For this reason

it is important this area to not be obstructed and the grille

openings kept clean. Marvel does not recommend the use



Figure 2).

Leveling Legs

Adjustable legs at the front and rear corners of the appli-



-

all height of your Marvel appliance may be adjusted be-

tween the minimum, 33

4" (85.7 cm), by turning the leveling

leg in (CW ↷) and the maximum, 34

4" (88.3 cm) by turning

the leveling leg out (CCW ↶).

To adjust the leveling legs, place the appliance on a solid





lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

INSTALLING YOUR APPLIANCE

NOTE

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

WARNING

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Figure 6

Figure 5

Front grille screw

Front grille

INSTALLING YOUR APPLIANCE

Figure 3

Figure 4

Do not remove

ground prong

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

Step by step instructions for locating the po-

sition of the bracket:

1) Decide where you want to place the drawer refrigerator.



leaving 1" (2.5 cm) of clearance from the rear wall to allow

room for the anti-tip bracket.

2) Raise the rear leveling legs approximately

" (6 mm) to

allow engagement with the anti-tip bracket. Level the unit

by adjusting all the leveling legs as required. Turning the

leveling leg counterclockwise will raise the unit and clock-

wise will lower the unit.

3) Make sure the refrigerator is in the desired location, then



where the anti-tip bracket will be installed. If the installation

does not allow marking the rear corner of the cabinet, then



of the cabinet, excluding the drawer. Slide the refrigerator

out of the way. From the temporary line extend the sidewall

line back 21

2" (54.6 cm) as shown in Figure 8.



the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 21

2" (54.6 cm) line (Rear of cabinet

line).



screw. (See Figure 8).

6) Slide the cabinet back into position, making sure the rear

cabinet leveling leg slides under the anti-tip bracket engag-

ing the slot.

Bottom View of

Refrigerated

Drawer Unit

Anti-Tip

Bracket

Leveling Leg

Front of cabinet

2"

(54.6 cm)

Figure 7

WARNING

• ALL APPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

• FOLLOW THE INSTRUC-

TIONS BELOW

Floor Mount Installation



or right rear corner of the refrigerator drawer as shown in

Figure 7.

CAUTION

NOTE



material to avoid damage when moving the unit.



required, (not included with the anti-tip kit).

Anti-Tip Device

WARNING

If your refrigerator is not located under a counter

top (free standing), you must use an anti-tip device

installed as per these instructions. If the refrigerator is

removed from its location for any reason, make sure

that the device is properly engaged with the anti-tip

bracket when you push the refrigerator back into the

original location. If the device is not properly engaged,

there is a risk of the refrigerator tipping over, with the

potential for property damage or personal injury.

INSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS

AND ENERGY SAVING TIPS

2"

(54.6 cm)

"V" notches

in bracket

"V" notches

in bracket

Figure 8

Rear of cabinet line

Figure 8a

Side of cabinet line

Front of cabinet line

Screw

Rear Leveling leg

NOTE

-

mum adjusted height of the cabinet is increased by

8" (9 mm).

The following suggestions will minimize the

cost of operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance

(cooker, dishwasher, etc.), heating air duct, or other

heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance be-

neath drawer are not obstructed and kept clean to allow

ventilation for the refrigeration system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize drawer

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

6. Maintaining a relatively full storage compartment will

require less appliance run time than an empty compart-

ment.

7. Ensure drawer closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before plac-

ing in product.

9. Minimize drawer openings and duration of drawer

openings.

10. Use the warmest temperature control set temperature

that meets your personal preference and provides the

proper storage for your stored contents.

11. When on vacation or away from home for extended

periods, set the appliance to warmest acceptable

temperature for the stored contents.



appliance requires the drawer to be open for an ex-

tended period of time.

Energy saving tips:

"A"

"B"

"C"

"D"

"E"

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "I"

MO24RDS

24"

(61 cm)

**34" to 35"

(86.4 cm to 88.9 cm)

8"

(60.7 cm)

4" to 34

4"

(85.7 cm to 88.3 cm)

32"

(60.2 cm)

32"

(66.6 cm)

32"

(99.5 cm)

32"

(105.8 cm)

Figure 9

Figure 9a

PRODUCT DIMENSIONS

Figure 10

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent

cabinet and the power cord routed through this

hole to a power outlet. Another way to increase

the available opening depth is to recess the power

outlet into the rear wall to gain the thickness of the

power cord plug. Not all recessed outlet boxes will

work for this application as they are too narrow,

but a recessed outlet box equivalent to Arlington

#DVFR1W is recommended for this application,

(see Figure 10).

"D"

"E"

"F"

"G"

"H"

Floor mount anti-tip bracket.

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

MO24RDS 115V/60Hz/15A

130 lbs

(59 kg)

2"

(54.6 cm)

(2.5 cm)

WARNING

Floor mount Anti-tip Bracket must be installed for freestand-

ing applications. Not required for built in applications.

Figure 11

* Depth dimension of rough-in opening may vary depending

on each individual installation. To recess entire drawer "F"

dimension plus 1" (2.5 cm) for thickness of power cord plug

is required.

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

PRODUCT DIMENSIONS

"I"

USING YOUR ELECTRONIC CONTROL

Starting your refrigerator

Plug the refrigerator power cord into a wall outlet. Your

refrigerator will begin cooling after power is applied.

If your refrigerator does not start, check that the refrigerator

is turned on and the set temperature is cold enough.

Turning your refrigerator ON or OFF

If the refrigerator is on, the refrigerator temperature will be



hold the "ON/OFF" button for three (3) seconds. "OFF" will

appear on the display.

If the refrigerator is not on, "OFF" will be shown on the

display. To turn the refrigerator on, press and hold the "ON/

OFF" button for three (3) seconds. The refrigerator tem-

perature will be shown on the display.

Set temperature

To set the refrigerator temperature, press and hold the

"SET" button. When the "SET" button is pressed, the

display will show the set temperature. While holding the

"SET" button, press the "WARMER" or "COLDER" buttons

to adjust set temperature.

Refrigerator operation

The available temperature range of the refrigerator is 34° to

42°F (1° to 6° C).

It may take up to 24 hours for your refrigerator to reach

desired temperature. This will depend on amount of content

loaded and number of door opening and closings.

For best results allow refrigerator to "pull down" to desired

set temperature before loading. Once contents are loaded,

allow at least 48 hours for temperature to stabilize before

making any adjustments to the set temperature.

Set

Colder Warmer

ON/OFF

Press and Hold Press and Hold

Alarm

Figure 12

close-up of

control

• Temperature Sensor Fault: If the control-

ler detects that the temperature sensor is

not properly functioning, a temperature

sensor alarm will sound in one (1) second intervals. "E1"



at the top left of the display below the word "Alarm" will be

illuminated. Please call Marvel Customer Service or your

dealer if this error code is displayed.

• High and Low Temperature Alarm: If

the storage compartment temperature deviates

excessively from the set-point temperature, the

alarm will sound in (1) second intervals. The

-

pending upon the condition and the Alarm LED

light at the top left of the display below the word

"Alarm" will be illuminated. The alarm will remain active

until the condition is corrected.

Alarms

Your electronic control will monitor refrigerator function and

alert you with a series of audible and visual alarms.

• Door Ajar Alarm: If the door has been left



will sound in one (1) second intervals. The



the top left of the display below the word "Alarm" will be il-

luminated. This will stop as soon as the door is closed.

Figure 13

Top drawer

NOTE

After a high temperature alarm condition, check all perish-

ables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage compart-

ment. If the temperature alarm continues to occur, your unit

may require service.

CAUTION

Light assembly replacement

All models use an LED to illuminate the interior of the ap-

pliance. This component is very reliable, but should it fail,



LED.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of drawer openings while the



temperature.

Care of Appliance

1. Avoid leaning on the drawer, you may bend the drawer

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop-

ping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

Front Grille

-

ings in front of the cabinet. At least once or twice a year,

brush or vacuum lint and dirt from the front grille area (see

page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The stainless steel cabinet can be washed with either a

mild soap and water and thoroughly rinsed with clear water.

See "Stainless Steel Maintenance" on page 13.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

CARE AND CLEANING

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the unit's wiring.

• Replace all parts and panels before operating.

WARNING

Electrocution Hazard

Alarm Mute

Press any key to mute the audible portion of an alarm.

This action will only mute the alarm. If the condition that

caused the alarm continues, the alarm code will continue to



NOTE

2. 

3. Remove all contents.

4. If necessary, move the unit so you can gain access to

the rear of the product.

5. Unplug the unit from the power outlet.

6. It is also recommended that the power to the outlet be



during the Winter season.

7. When cleaning unit pay particular attention to any

cracks and crevices that may have accumulated dirt

and debris.

8. Remove the front toe-grille, (see Figure 14), and use a

brush and vacuum to clean dirt and debris from be-

neath the unit.

9. Thoroughly clean the toe-grille and re-install on the

unit. (See Figure 14).

10. Remove the rear access cover, (see Figure 15), and

use a brush and vacuum to clean dirt and debris from

the machine compartment.

11. Thoroughly clean the rear access cover and re-install

on the unit.

12. Wipe down all interior surfaces with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals which could cause staining. Do

not use any abrasive cleaners or scouring pads.

13. Leave the drawers open and allow to completely dry

out before closing the drawers.

14. Thoroughly clean the drawer gaskets with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals.

15. Thoroughly clean the exterior with a cleaner approved

for stainless steel. Do not use any abrasive cleaners or

scouring pads. See "Stainless Steel Maintenance" on

page 13.

16. Any mounting hardware / fasteners that are showing

signs of corrosion should be replaced.

17. Once the exterior has been thoroughly cleaned, you

may want to apply a coating of car wax to help protect

against spotting from moisture, dirt, and debris that

may accumulate on the surfaces during the Winteriza-

tion period.

• If the plastic defrost drain pan located under the

compressor contains water, use a sponge to

remove as much water as possible.

Start-Up After Long-Term Storage:

1. If stored outside, it is recommended that the unit again

be thoroughly inspected per the storage instructions

above to address any dirt or debris from the weather

and/or animals/insects.

2. Connect the unit to electrical power.

3. 

4. Allow 24-hrs for the unit to stabilize before loading

contents.

Figure 15

Soak up

water from

plastic drain

pan if

necessary

Clean out

debris

CARE AND CLEANING

Clean out

behind grille

Grille

Spacer

Figure 14

Outdoor Product Long-Term Storage / Winter-

ization:

1. Time to Winterize, when the daily low ambient tempera-

ture is at or below 38°F (3.3°C).

CAUTION

Operation of the unit at ambient temperatures below the

recommended Winterization temperature will void your war-

ranty.

Remove screw from

each end of grille

18. Do not place a cover on the unit, as this can trap con-

densation.

After completion of the above, you may choose to store the

unit indoors, although this is not required.

Remove screws

around perimeter

of access cover.

Access cover

Background

Stainless steel does not stain, corrode, or rust as easily as

ordinary steel, but it is not stain or corrosion proof. Stain-

less steels can discolor or corrode if not maintained prop-

erly.



amount of chromium present. It is this chromium that





surface can be damaged or contaminated, which may

result in discoloration, staining, or corrosion of the base

metal.

Care & Cleaning

Routine cleaning of the stainless steel surfaces will serve to

greatly extend the life of your product by removing contami-

nants. This is especially important in coastal areas which

can expose the stainless to severe contaminants such as

halide salts, (sodium chloride).

It is strongly recommended to periodically inspect and thor-

oughly clean crevices, weld points, under gaskets, rivets,

bolt heads, and any locations where small amounts of liquid

could collect, become stagnant, and concentrate contami-

nates. Additionally, any mounting hardware that is showing

signs of corrosion should be replaced.

Frequency of cleaning will depend upon the installation

location, environmental, and usage conditions.

Choosing a Cleaning Product

The choice of a proper cleaning product is ultimately that

of the consumer, and there are many products from which

to choose. Depending upon the type of cleaning and the

degree of contamination, some products are better than

others.



cleaning of most stainless steel products is to give the sur-

faces a brisk rubbing with a soft cloth soaked in warm water

and a gentle detergent, or mild mixture of ammonia. Rub-

bing should, to the extent possible, follow the polish lines of

the steel, and always insure thorough rinsing after cleaning.

Although some products are called "stainless steel clean-

ers," some may contain abrasives which could scratch the



and some many contain chlorine bleach which will dull,

tarnish or discolor the surface if not completely removed.

After the stainless surfaces have been thoroughly cleaned,

a good quality car wax may be applied to help maintain the



Stainless steel products should never be installed, or stored

in close proximity to chlorine chemicals.

Whichever cleaning product you chose, it should be used

in strict accordance with the instructions of the cleaner

manufacturer.

NOTE

STAINLESS STEEL MAINTENANCE AND OBTAINING SERVICE

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the unit's wiring.

• Replace all parts and panels before operating.

WARNING

Electrocution Hazard

For Your Records

Date of Purchase

Dealer’s name

Dealer’s Address

Dealer’s City

Dealer’s State

Dealer’s Zip Code

Appliance Serial Number

Rev. Letter

Appliance Service Number

Date Warranty Card Sent (Must

be within 10 days of purchase).

Table A

• In all correspondence regarding service, be sure to

give the service number, serial number, and proof of

purchase.

• Try to have information or description of nature of the

problem, how long the appliance has been running, the

room temperature, and any additional information that

may be helpful in quickly solving the problem.

• Table "A" is provided for recording pertinent information

regarding your product for future reference.

If Service is Required:

• 

please contact your dealer or call Marvel Customer

Service at 800.223.3900 for directions on how to obtain

warranty coverage in your area.

• 

Marvel Customer Service can provide recommenda-

tions of service centers in your area. A listing of autho-

rized service centers is also available at www.marvelre-

frigeration.com under the service and support section.

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the units wiring.

• Replace all parts and panels before operating.

WARNING

Electrocution Hazard

Before You Call for Service

If the appliance appears to be malfunctioning, read through

-

shooting guide below. Locate the problem in the guide and

refer to the cause and its remedy before calling for service.

The problem may be something very simple that can be

solved without a service call. However, it may be required



TROUBLESHOOTING

Problem Possible Cause Remedy

Appliance not cold enough

(See “Adjusting the temperature" on page

10)

• Control set too warm

• Content temperature not stabilized.

• Excessive usage or prolonged drawer

openings.

• 

• Drawer gasket not sealing properly.

• Adjust temperature colder. Allow 24

hours for temperature to stabilize.

• Allow temperature to stabilize for at

least 24 hours.

• 



page 4.

• Adjust or replace drawer gasket.

Appliance too cold



10)

• Control set too cold

• Drawer gasket not sealing properly.

• Adjust temperature warmer.

Allow 24 hours for temperature to

stabilize.

• Adjust or replace drawer gasket.

No interior light. • Failed LED light assembly or light

switch.

• 

Light will not go out when drawer is closed • Drawer not activating light switch.

• Failed light switch

• Appliance not level, level appliance,



• 

Noise or Vibration • Appliance not level

• Fan hitting tube obstruction.

• 

on page 4.

• 

Appliance will not run. • 

• Power cord not plugged in.

• No power at outlet.

• Turn appliance on. See “Starting your



• Plug in power cord.

• Check house circuit.

CAUTION

In the unlikely event you lose cooling in your unit, do not

unplug the product from the electric supply, but do call



that the loss of cooling capacity is a result of excessive

frost build-up on the evaporator cooling coil. In this case,

removing power to the unit will result in the melting of this

excessive quantity of ice, which could generate melt water

that exceeds the capacity of the defrost drain system and

could result in water damage to your home. The end-user

will be ultimately responsible for any water damage caused





Marvel Refrigeration (Marvel) Limited Warranty

ONE YEAR LIMITED PARTS & LABOR WARRANTY

For one year from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the

product that proves to be defective in materials or workmanship. For products installed and used for normal residential use,

material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.

All service provided by Marvel under the above warranty must be performed by a Marvel factory authorized servicer, unless



TWO YEAR LIMITED PARTS & LABOR WARRANTY (MARVEL PROFESSIONAL PRODUCTS)

For two years from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the

product that proves to be defective in materials or workmanship. For products installed and used for normal residential use,

material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.

All service provided by Marvel under the above warranty must be performed by a Marvel factory authorized servicer, unless

AVAILABLE THIRD YEAR LIMITED WARRANTY (MARVEL PROFESSIONAL PRODUCTS)



of purchase, free of charge. To take advantage of this third year warranty, you must register your product with Marvel within 60

days from the date of purchase at marvelrefrigeration.com and provide proof of purchase.

LIMITED FIVE YEAR SEALED SYSTEM WARRANTY



to be defective in materials or workmanship: compressor, condenser, evaporator, drier, and all connecting tubing. All service

provided by Marvel under the above warranty must be performed by a Marvel factory authorized servicer, unless otherwise



WARRANTY TERMS



or the ten provinces of Canada. The warranties do not cover any parts or labor to correct any defect caused by negligence,



product must be installed, operated, and maintained in accordance with the Marvel User Guide.

The remedies described above for each warranty are the only ones that Marvel will provide, either under these warranties or

under any warranty arising by operation of law. Marvel will not be responsible for any consequential or incidental damages

arising from the breach of these warranties or any other warranty, whether express, implied, or statutory. Some states do not

allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to



Any warranty that may be implied in connection with your purchase or use of the product, including any warranty of





limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

• The warranties only apply to the original purchaser and are non-transferable.

• These warranties cover products installed and used for normal residential use only.

• The warranties apply to units operated outside only if designed for outdoor use by model and serial number.

 

• The start of Marvel’s obligation is limited to four years after the shipment date from Marvel.

• In-home instruction on how to use your product is not covered by these warranties.

• Food, beverage, and medicine loss are not covered by these warranties.

• If the product is located in an area where Marvel factory authorized service is not available, you may be responsible for a

trip charge or you may be required to bring the product to a Marvel factory authorized service location at your own cost and

expense.

 

only and no coverage is provided for cosmetic defects.

• Signal issues related to Wi-Fi connectivity are not covered by these warranties.

For parts and servi

MarvelRefrigeration.com • [email protected] • +616.754.5601

1260 E. Van Deinse St., Greenville, MI 48838

HOUSEHOLD PRODUCT WARRANTY

Marvel Refrigeration



the buyer to corresponding changes, improvements, additions, replacements or compensation for

previously purchased products.

www.marvelrefrigeration.com

1260 E. VanDeinse St.

Greenville MI 48838

800.223.3900

41013921-EN Rev G

1/15/20

Outdoor Refrigerated Drawers

Tiroirs réfrigérés d' extérieur

MO24RD

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

Contenu :

Informations de sécurité.......................................................2

Déballage de votre appareil ..................................................3

Enregistrement de la garantie .......................................3

Installation de votre appareil ..............................................4

Dégagements par rapport à l’armoire .............................4

Mise à niveau de l’appareil .............................................4

Raccordement électrique.................................................5

Installation du dispositif anti-basculement............................6

Conseils pour l’économie d’énergie ..................................7

Dimensions du produit.........................................................8

Utilisation de votre commande électronique .....................10

Démarrage de votre appareil ........................................10

Mise en marche et arrêt de votre appareil .....................10

Réglage de la température ............................................10

Alertes...........................................................................10

Entretien et nettoyage .......................................................11

Entreposage de longue durée / préparation

à l’hivernage .................................................................12

Entretien de l’acier inox ....................................................13

Dépannage................................................................14

Obtention de service ..........................................................14

Garantie...........................................................................15

CONTENU

REMARQUE

ATTENTION

Importantes instructions de sécurité

Les avertissements et les instructions de sécurité qui ap-

paraissent dans ce guide n’ont pas la prétention de couvrir

toutes les conditions et situations possibles pouvant arriver.

Il faut faire preuve de bon sens, de précautions et de soins,

pour installer, utiliser ou entretenir cet appareil.

Reconnaissance des symboles,

des mots et des étiquettes

concernant la sécurité.

ATTENTION - Risques ou pratiques dangereuses

pouvant entraîner des blessures individuelles, des dégâts

matériels ou des dommages au produit.

REMARQUE - Information importante pour réaliser une

installation et une utilisation sans problèmes.

AVERTISSEMENT - Risque possible de décès ou

de blessure grave si vous ne suivez pas les instructions.

AVERTISSEMENT

Avertissements de la proposition 65 de l'État de Californie

: Ce produit contient au moins un produit chimique connu par

l’État de Californie pour être à l’origine de cancers.

AVERTISSEMENT

Avertissements de la proposition 65 de l'État de Californie

: Ce produit contient au moins un produit chimique connu par

l’État de Californie pour être à l’origine de malformations et

autres déciences de naissance.

AVERTISSEMENT

DÉBALLAGE DE VOTRE APPAREIL

XXXXXXXXXXXX

AVERTISSEMENT

ATTENTION

REMARQUE

Enregistrement de la garantie

Il est important que vous postiez votre carte de garantie

immédiatement après avoir pris livraison de votre réfrigérateur.

Les informations suiv-

antes seront néces-

saires au moment de

l’enregistrement de votre

appareil :

Numéro de service

Numéro de série

Date d’achat

Nom et adresse du revendeur

La numéro de service et le numéro de série se trouvent sur

la plaque signalétique qui est située dans le meuble, en bas

du revêtement du côté gauche. Ouvrez le tiroir du bas pour y

accéder(Voyez la

Figure 1).

AVERTISSEMENT

RISQUE DE POIDS EXCESSIF

Utilisez deux personnes ou plus pour déplacer le produit.

Sinon vous pourriez vous blesser.

Enlèvement de l’emballage intérieur

Votre réfrigérateur a été emballé pour l’expédition avec toutes les

pièces pouvant être endommagées par le mouvement solidement

attachées. Enlevez les matériaux d’emballage intérieur et toute

bande maintenant des composants intérieurs en place. Le manuel

de l’utilisateur est envoyé à l’intérieur de l’appareil dans un sac en

plastique, accompagné de la carte d’enregistrement de la garan-

tie, et d’autres articles accessoires.

Important

Conservez votre carton d’emballage jusqu'à ce que votre réfri-

gérateur ait été complètement inspecté et trouvé en bon état.

S’il présentait des dommages, cet emballage serait nécessaire

comme preuve qu’ils sont survenus durant le transit. Ensuite

veuillez mettre tous ces matériaux d’emballage au rebut d’une

façon responsable.

Note pour le client

Cette marchandise a été soigneusement et complètement inspec-

tée avant de quitter notre usine. La responsabilité pour sa livrai-

son sûre a été assumée par le revendeur à l’acceptation de cette

expédition. Les réclamations pour perte ou dommages survenus

durant le transit sont à adresser au revendeur.

NE RENVOYEZ PAS DE MARCHANDISE ENDOMMA-

GÉE AU FABRICANT – DÉPOSEZ UNE RÉCLAMATION

AUPRÈS DU REVENDEUR.

Si l’appareil a été livré, manipulé ou entreposé dans une posi-

tion autre que debout, pendant une durée quelconque, laissez-le

reposer debout pendant au moins 24 heures avant de la brancher

électriquement. Cela assurera le retour de l’huile au compresseur.

Un branchement immédiat de l’appareil pourrait endommager des

parties internes.

Figure 1

Enregistrement

en ligne disponible

sur

www.marvelrefrigeration.

com

AVERTISSEMENT - Jetez bien les sacs en plastique qui

représentent un risque de suocation.

AVERTISSEMENT

AVERTISSEMENT - Contribuez à éviter des tragédies

L’emprisonnement d’enfants et leur asphyxie ne sont pas

des problèmes du passé. Des épaves de réfrigérateurs

abandonnés continuent de présenter un danger - même

en restant dehors pour «juste quelques heures».

Si vous devez vous débarrasser de votre vieil appareil

de refroidissement, veuillez suivre ces instructions pour

aider à éviter des accidents possibles.

Avant de jeter votre vieux réfrigérateur ou congélateur :

• Démontez ses portes ou enlevez ses tiroirs.

• Laissez les étagères en place de façon à ce que des

enfants ne puissent pas facilement monter dedans.

AVERTISSEMENT

MARVEL

Pieds de mise à

niveau avant

Figure 2

Pieds de

mise à niveau

arrière

Grille frontale,

gardez cette

zone dégagée.

Pieds de mise à niveau

Des pieds réglables aux angles avant et arrière de l’armoire

doivent être ajustés pour qu’elle soit fermement positionnée

au sol et bien d’aplomb, d’un côté à l’autre et d’avant en

arrière. La hauteur totale de votre appareil Marvel peut être

ajustée entre le minimum 33

⁄4 po (85,7 cm) (en vissant les

pieds de mise à niveau CW ↷) et le maximum 34

⁄4 po (88,3

cm) (en dévissant les pieds de mise à niveau CCW ↶) des.

Pour régler ces pieds de mise à niveau, placez l’appareil

sur une surface solide, en protégeant le sol en dessous

pour ne pas le rayer. Avec l’aide d’une autre personne, in-

clinez vers l’arrière de l’appareil pour accéder aux pieds de

mise à niveau de l’avant. Levez ou abaissez ces pieds à la

hauteur requise en les tournant. Répétez la procédure pour

les pieds arrière en inclinant le cave à vin vers l’avant en

faisant attention. Sur une surface plane, vériez le niveau

de l’appareil et ajustez les pieds en conséquence.

Les vis de la grille frontale peuvent être desserrées et la

grille ajustée à la hauteur voulue. Quand le réglage est fait

resserrez les vis de la grille frontale (Voyez la Figure 5).

Choix de l’emplacement

Un bon emplacement assurera une performance de pointe pour

votre appareil. Nous recommandons un endroit où l’appareil ne

sera pas exposé directement au rayonnement solaire et restera

écarté de sources de chauage. Pour assurer que les perfor-

mances de votre produit soient au niveau de ses spécications, la

plage de températures recommandée au lieu d’installation sera de

55 à 100°F (13 à 38 °C).

Dégagements par rapport à l’armoire

Une ventilation est nécessaire depuis la section frontale du bas de

l’armoire. Gardez cette zone libre et exempte de toutes obstruc-

tions. Des meubles et comptoirs peuvent être installés autour de

l’unité de façon adjacente dans la mesure où sa grille frontale

restera non obstruée. Les modèles à revêtement de porte avec

charnières articulées sont prévus pour des applications encas-

trées uniquement.

INSTALLATION DE VOTRE APPAREIL

ATTENTION

Grille frontale

N’obstruez pas la grille frontale. Les ouvertures au travers de la

grille frontale permettent l’écoulement de l’air par l’échangeur

thermique du condenseur. Des restrictions de ce ux d’air vont

augmenter la consommation d’énergie et aecter sa capacité de

refroidissement. C’est pourquoi il est important que cette zone ne

soit pas obstruée et soit maintenue propre. Marvel recommande

de ne pas utiliser de grilles personnalisées, car l’écoulement d’air

en serait diminué (Voyez la

Figure 2).

La page charge ...

Marvel MO24RD Mode d'emploi

Marque: Marvel

Modèle: MO24RD

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Marvel MO24RD User guide

Marvel MO24RD Mode d'emploi

Marvel MO24RD Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents