Wacker Neuson CT36-6 Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

5200000875 02 0413
Operator’s Manual
Walk-Behind Trowel
CT 36 / CT 48
Notice d’Emploi
Truelle mécanique
5200000875
EN / FR
Copyright
notice
© Copyright 2013 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the machine. Any
other type of reproduction is prohibited without express written permission from
Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker Neuson Production
Americas LLC represents an infringement of valid copyrights. Violators will be
prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original
instructions
This Operator’s Manual presents the original instructions. The original language of this
Operator’s Manual is American English.
5200000874 02 0413
CT 36 / CT 48 Foreword
wc_tx003227gb.fm 3
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machines
covered by
this manual
Machine
identification
A nameplate listing the model number, item number, revision number, and serial
number is attached to this machine. The location of the nameplate is shown above.
Serial number
(S/N)
For future reference, record the serial number in the space provided below. You will
need the serial number when requesting parts or service for this machine.
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
Use the separate Parts Book supplied with the machine to order replacement
parts.
If you are missing either of these documents, please contact Wacker Neuson to
order a replacement or visit www.wackerneuson.com.
When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Machine Item Number Machine Item Number
CT 36-6 0009443
0620830
CT 48-9 0009453
0620838
CT 36-9 0009444
0620833
CT 36-9V 0009447
0620834
wc_gr010106
Serial Number:
Foreword CT 36 / CT 48
4 wc_tx003227gb.fm
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change
any portion of this information without notice.
The illustrations, parts, and procedures in this manual refer to Wacker Neuson
factory-installed components. Your machine may vary depending on the
requirements of your specific region.
CALIFORNIA
Proposition
65 Warning
Combustion exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-
charge of sparks or flames from the engine exhaust. Spark arresters are qualified
and rated by the United States Forest Service for this purpose. In order to comply
with local laws regarding spark arresters, consult the engine distributor or the local
Health and Safety Administrator.
Manufacturers
approval
This manual contains references to approved parts, attachments, and
modifications. The following definitions apply:
Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following
consequences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
Original Declaration of Conformity
2013-CE-CT36_CT48_en.fm
EC Declaration of Conformity
Manufacturer
Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,
Menomonee Falls, Wisconsin 53051, USA
Product
Product
Product category
Product function
Item number
CT 36-5A, CT 36-8A, CT 36-8A-V, CT 36-6, CT 36-9,
CT 36-9-V, CT 48-8A, CT 48-11A, CT 48-13A-V, CT 48-9
Trowel
To smooth and finish semi-cured concrete
0620829, 0620830, 0620831, 0620832, 0620833,
0620834, 0620835, 0620836, 0620837, 0620838
Directives and Standards
We hereby declare that this product meets and complies with the relevant regulations and
requirements of the following directives and standards:
2006/42/EC, 2004/108/EC, EN12649
Authorized Person for Technical Documents
Axel Häret, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41,
80809 München
Menomonee Falls, WI, USA, 19.2.13
William Lahner
Managing Director
Scott V. Grahl
Manager, Product Engineering
Dan Domanski
Technical Director
wc_bo5200000874_02TOC.fm 7
Table of ContentsCT 36 / CT 48
Foreword 3
EC Declaration of Conformity 5
1 Safety Information 9
1.1 Signal Words Used in this Manual ....................................................... 9
1.2 Machine Description and Intended Use ............................................. 10
1.3 Safety Guidelines for Operating the Machine ..................................... 11
1.4 Service Safety .................................................................................... 13
1.5 Operator Safety while Using Internal Combustion Engines ............... 15
2 Labels 16
2.1 Label Locations .................................................................................. 16
2.2 Label Meanings .................................................................................. 17
3 Lifting and Transporting 20
3.1 Lifting the Machine ............................................................................. 20
3.2 Transporting the Machine ................................................................... 22
4 Operation 23
4.1 Preparing the Machine for First Use ................................................... 23
4.2 New Machine Set-up .......................................................................... 23
4.3 Recommended Fuel ........................................................................... 24
4.4 Installing the Blades ........................................................................... 25
4.5 Installing and Adjusting Handles ........................................................ 26
4.6 Controls .............................................................................................. 28
4.7 Braking System .................................................................................. 28
4.8 Engine Control Module ....................................................................... 29
4.9 Stop Button ......................................................................................... 29
4.10 Before Starting ................................................................................... 29
4.11 Starting ............................................................................................... 30
4.12 Stopping ............................................................................................. 31
4.13 Position of the Operator ..................................................................... 32
4.14 Operation ............................................................................................ 32
4.15 Pitch Adjustment ................................................................................ 34
4.16 Emergency Shutdown Procedure ....................................................... 35
8 wc_bo5200000874_02TOC.fm
Table of Contents CT 36 / CT 48
5 Maintenance 36
5.1 Maintaining the Emission Control System ...........................................36
5.2 Periodic Maintenance Schedule ..........................................................37
5.3 Engine Oil ............................................................................................38
5.4 Servicing the Air Cleaner .....................................................................39
5.5 Spark Plug ...........................................................................................40
5.6 Cleaning the Fuel Strainer ...................................................................41
5.7 Belt Replacement ................................................................................42
5.8 Trowel Lubrication ...............................................................................44
5.9 Optional Weights .................................................................................44
5.10 Storage ................................................................................................45
6 Troubleshooting 46
7 Technical Data 47
7.1 Dimensions ..........................................................................................47
7.2 Engine .................................................................................................48
7.3 Machine ...............................................................................................50
7.4 Sound and Vibration Specifications .....................................................51
8 Emission Control Systems Information and Warranty 52
8.1 Emission Control System Background Information .............................52
8.2 Limited Defect Warranty for Wacker Neuson Emission Control
Systems ...............................................................................................53
9 AEM Safety Manual 57
wc_si000739gb.fm
9
CT 36 / CT 48 Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
f Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
f To avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
f To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
f To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_si000739gb.fm
10
Safety Information CT 36 / CT 48
1.2 Machine Description and Intended Use
This machine is a walk-behind concrete finishing trowel. The Wacker Neuson
Walk-Behind Trowel consists of a frame onto which are mounted a gasoline
engine, a fuel tank, a gearbox, and a control handle. A set of four metal blades is
connected to the gearbox and is surrounded by a ring guard. The engine rotates
the blades through the gearbox and clutch mechanism. The rotating blades ride on
the surface of curing concrete, creating a smooth finish. The operator walks behind
the machine and uses the handle to control speed and direction of the machine.
This machine is intended to be used for floating and burnishing curing concrete.
This machine has been designed and built strictly for the intended use described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty.
The following are some examples of misuse:
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Using the machine to finish inappropriate materials such as slurries, sealers, or
epoxy finishes
Operating the machine outside of factory specifications
Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operators Manual
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
Heat, noise, exhaust, and carbon monoxide from the engine
Chemical burns from curing concrete
Fire hazards from improper refueling techniques
Fuel and its fumes, fuel spillage from improper lifting technique
Personal injury from improper lifting techniques or operating techniques
Cutting hazards from sharp or worn blades
To protect yourself and others, make sure you thoroughly read and understand the
safety information presented in this manual before operating the machine.
wc_si000739gb.fm
11
CT 36 / CT 48 Safety Information
1.3 Safety Guidelines for Operating the Machine
Operator
training
Before operating the machine:
Read and understand the operating instructions contained in all manuals
delivered with the machine.
Familiarize yourself with the location and proper use of all controls and safety
devices.
Contact Wacker Neuson for additional training if necessary.
When operating this machine:
Do not allow improperly trained people to operate the machine. People
operating the machine must be familiar with the potential risks and hazards
associated with it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
have received instruction on how to properly use the machine
are familiar with required safety devices
The machine must not be accessed or operated by:
children
people impaired by alcohol or drugs
Application
area
Be aware of the application area.
Keep unauthorized personnel, children, and pets away from the machine.
Remain aware of changing positions and the movement of other equipment and
personnel in the application area/job site.
Be aware of the application area.
Do not operate the machine in areas that contain flammable objects, fuels, or
products that produce flammable vapors.
Safety
devices,
controls, and
attachments
Only operate the machine when:
All safety devices and guards are in place and in working order.
All controls operate correctly.
The machine is set up correctly according to the instructions in the Operator’s
Manual.
The machine is clean.
The machine’s labels are legible.
To ensure safe operation of the machine:
Do not operate the machine if any safety devices or guards are missing or
inoperative.
Do not modify or defeat the safety devices.
Only use accessories or attachments that are approved by Wacker Neuson.
wc_si000739gb.fm
12
Safety Information CT 36 / CT 48
Safe
operating
practices
When operating this machine:
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
When operating this machine:
Do not operate a machine in need of repair.
Do not operate the machine with the beltguard missing. Exposed drive belt and
pulleys create potentially dangerous hazards that can cause serious injuries.
Do not use the trowel around pop-ups in the concrete that are lower than the
lowest ring on the ring guard.
Do not lift the machine solely by the handle. The component may fail, causing
the machine to fall, possibly injuring bystanders.
Test the function of the engine control module before operating the trowel. Do
not operate the trowel if the engine control module is not functioning properly.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while operating this
machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
After Use
Stop the engine when the machine is not being operated.
Close the fuel valve on engines equipped with one when machine is not being
operated.
Ensure that the machine will not tip over, roll, slide, or fall when not being
operated.
Store the machine properly when it is not being used. The machine should be
stored in a clean, dry location out of the reach of children.
wc_si000739gb.fm
13
CT 36 / CT 48 Safety Information
1.4 Service Safety
Service training
Before servicing or maintaining the machine:
Read and understand the instructions contained in all manuals delivered
with the machine.
Familiarize yourself with the location and proper use of all controls and
safety devices.
Only trained personnel shall troubleshoot or repair problems occurring with
the machine.
Contact Wacker Neuson for additional training if necessary.
When servicing or maintaining this machine:
Do not allow improperly trained people to service or maintain the machine.
Personnel servicing or maintaining the machine must be familiar with the
associated potential risks and hazards.
Precautions
Follow the precautions below when servicing or maintaining the machine.
Read and understand the service procedures before performing any service
to the machine.
All adjustments and repairs must be completed before operation. Do not
operate the machine with a known problem or deficiency.
All repairs and adjustments shall be completed by a qualified technician.
Turn off the machine before performing maintenance or making repairs.
Machine
modifications
When servicing or maintaining the machine:
Use only accessories/attachments that are approved by Wacker Neuson.
When servicing or maintaining the machine:
Do not defeat safety devices.
Do not modify the machine without the express written approval of Wacker
Neuson.
Replacing parts
and labels
Replace worn or damaged components.
Replace all missing and hard-to-read labels.
When replacing electrical components, use components that are identical in
rating and performance to the original components.
When replacement parts are required for this machine, use only Wacker
Neuson replacement parts or those parts equivalent to the original in all
types of specifications, such as physical dimensions, type, strength, and
material.
wc_si000739gb.fm
14
Safety Information CT 36 / CT 48
Cleaning
When cleaning and servicing the machine:
Keep the machine clean and free of debris such as leaves, paper, cartons,
etc.
Keep the labels legible.
When cleaning the machine:
Do not clean the machine while it is running.
Never use gasoline or other types of fuels or flammable solvents to clean
the machine. Fumes from fuels and solvents can become explosive.
Personal
Protective
Equipment (PPE)
Wear the following Personal Protective Equipment (PPE) while servicing or
maintaining this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
In addition, before servicing or maintaining the machine:
Tie back long hair.
Remove all jewelry (including rings).
Safe service
practices
Do not crank a flooded engine with the spark plug removed on gasoline-
powered engines. Fuel trapped in the cylinder will squirt out the spark plug
opening.
Do not test for spark on gasoline-powered engines if the engine is flooded or
the smell of gasoline is present. A stray spark could ignite the fumes.
Disconnect the spark plug on machines equipped with gasoline engines,
before servicing, to avoid accidental start-up.
Do not remove blades while the machine is hanging overhead.
Support the machine securely before changing blades.
Handle blades carefully. The blades can develop sharp edges which can
cause serious cuts.
wc_si000739gb.fm
15
CT 36 / CT 48 Safety Information
1.5 Operator Safety while Using Internal Combustion Engines
Operating
safety
When running the engine:
Keep the area around exhaust pipe free of flammable materials.
Check the fuel lines and the fuel tank for leaks and cracks before starting the
engine. Do not run the machine if fuel leaks are present or the fuel lines are
loose.
When running the engine:
Do not smoke while operating the machine.
Do not run the engine near sparks or open flames.
Do not touch the engine or muffler while the engine is running or immediately
after it has been turned off.
Do not operate a machine when its fuel cap is loose or missing.
Do not start the engine if fuel has spilled or a fuel odor is present. Move the
machine away from the spill and wipe the machine dry before starting.
Refueling
safety
When refueling the engine:
Clean up any spilled fuel immediately.
Refill the fuel tank in a well-ventilated area.
Reinstall the fuel tank cap after refueling.
Do not smoke.
Do not refuel a hot or running engine.
Do not refuel the engine near sparks or open flames.
Use suitable tools for refueling (for example, a fuel hose or funnel).
Do not refuel if the machine is positioned in a truck fitted with a plastic bed liner.
Static electricity can ignite the fuel or fuel vapors.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
f Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
Exhaust gas from the engine contains carbon monoxide, a deadly poison.
Exposure to carbon monoxide can kill you in minutes.
f NEVER operate the machine inside an enclosed area, such as a tunnel, unless
adequate ventilation is provided through such items as exhaust fans or hoses.
wc_si000740gb.fm
16
Labels CT 36 / CT 48
2 Labels
2.1 Label Locations
wc_gr010351
J
C
H
G
D
F
L
B
E
A
M
K
wc_si000740gb.fm
17
CT 36 / CT 48 Labels
2.2 Label Meanings
A Engine stop button:
Press to stop engine.
B Variable speed throttle
C WARNING!
Always wear hearing and eye protection when
operating this machine.
D DANGER
Asphyxiation hazard
Engines emit carbon monoxide.
Do not run the machine indoors or in an
enclosed area unless adequate ventilation,
through such items as exhaust fans or hoses,
is provided.
Read the Operator’s Manual. No sparks,
flames, or burning objects near the machine.
Stop the engine before refueling.
E NOTICE
Lifting point
178709
wc_si000740gb.fm
18
Labels CT 36 / CT 48
F CAUTION!
Read and understand the supplied Operator’s
Manual before operating this machine. Failure to
do so increases the risk of injury to yourself and
others.
G WARNING
Hot surface
H WARNING!
Hand injury if caught in moving belt.
Always replace beltguard.
J Use only Glygoyle 460 gear oil in gearbox.
K This machine may be covered by one or more
patents.
WACKER NEUSON
wc_si000740gb.fm
19
CT 36 / CT 48 Labels
L WARNING
Cutting hazard. Always replace blade guard.
M
To start the machine:
1. Open the fuel flow valve.
2. Close the choke.
3. Push or turn engine switch to ON position.
4. Place throttle in the IDLE position.
5. Pull the rewind starter.
6. Open the choke.
To stop the machine:
1. Press the stop button.
2. Push or turn engine switch to OFF position.
3. Close the fuel flow valve.
wc_tx003223gb.fm
20
Lifting and Transporting CT 36 / CT 48
3 Lifting and Transporting
3.1 Lifting the Machine
Do not lift the machine solely by the handle. The component may fail, causing the
machine to fall, possibly injuring bystanders.
Note: See “Dimensions and Weight” for the weight of the machine.
To lift the machine manually:
1. Stop engine.
2. Obtain a partner and plan the lift.
3. Balance the weight between the partners and lift the machine by the guard ring
(a), or proceed as follows:
a.Attach optional lifting bracket (c) to trowel with screws and locknuts. Torque
screws to 25 Nm (18 ft.lbs.).
a.Insert a 2x4 or other suitable lumber into the bracket. The lumber must be
long enough to extend past the ring guard.
b.Balance the weight between the partners and lift the machine by the handle
and the lumber.
To reduce risk of back injury while lifting, keep your feet flat on ground and shoulder
width apart. Keep your head up and back straight.
To lift the machine mechanically:
1. Stop engine.
2. See Dimensions and Weight for weight of machine and be sure that lifting
device(s) can safely lift the weight.
3. Attach optional lifting bracket (b) to trowel with screws and locknuts. Torque to
25 Nm (18 ft.lbs.).
4. Attach hook, harness, or cable to the lifting bracket on machine as shown and
lift as desired.
Do not lift the trowel overhead with a float pan attached, as the pan could fall off
and strike personnel working in the vicinity.
WARNING
WARNING
WARNING
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136

Wacker Neuson CT36-6 Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues