Wacker Neuson CT48-8A EU Manuel utilisateur

Taper
Manuel utilisateur
Operator’s Manual
Notice d'emploi
Walk-Behind Trowels
Truelle mécanique
CT36/CT36A
CT48/CT48A
Type CT36/CT36A, CT48/CT48A
Document
5100022588
Date 1215
Version 01
Language
EN-FR
5100022588
Copyright notice
© Copyright 2015 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the
machine. Any other type of reproduction is prohibited without express
written permission from Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker
Neuson Production Americas LLC represents an infringement of valid
copyrights. Violators will be prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their
respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original instructions
This Operator’s Manual presents the original instructions. The original
language of this Operator’s Manual is American English.
Foreword
wc_tx004116gb_FM10.fm 3
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machines
covered by
this manual
Machine
identification
A nameplate listing the model number, item number, revision number, and serial
number is attached to this machine. The location of the nameplate is shown above.
Serial number
(S/N)
For future reference, record the serial number in the space provided below. You will
need the serial number when requesting parts or service for this machine.
Machine Item Number Machine Item Number
CT 36-6 5000009443
5000620830
CT 48-9 5000009453
5000620838
CT 36-9 5000009444
5000620833
CT 36-9V 5000009447
5000620834
CT 36-5A 5000009438
5000620106
5000620829
5200016256
CT 48-8A 5000009449
5000620837
CT 36-8A 5000009439
5000620831
CT 48-11A 5000009450
5000620835
CT 36-8A-V 5000009442
5000620832
CT 48-13A-V 5000009452
5000620836
wc_gr010106
m3/hrm3/hr
Type/ModelType/Model
gpmgpm
Rev.Rev.
MADE IN USA MADE IN USA
kWkW
lbslbs
kgkg
Item NumberItem Number
Manuf.Yr.Manuf.Yr.
hphp
ftft
m
Serial NumberSerial Number
150188150188
Serial Number:
Foreword
4 wc_tx004116gb_FM10.fm
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
For spare parts information, please see your Wacker Neuson Dealer, or visit
the Wacker Neuson webs
ite at http://www.wackerneuson.com/.
When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change any
portion of this information without notice.
The illustrations, parts, and procedures in this manual refer to Wacker Neuson
factory-installed components. Your machine may vary depending on the
requirements of your specific region.
CALIFORNIA
Proposition
65 Warning
Engine exhaust, some of its constituents, and certain vehicle components contain
or emit chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental
discharge of sparks or flames from the engine exhaust. Spark arresters are
qualified and rated by the United States Forest Service for this purpose. In order to
comply with local laws regarding spark arresters, consult the engine distributor or
the local Health and Safety Administrator.
Foreword
wc_tx004116gb_FM10.fm 5
Manufacturer’s
approval
This manual contains references to approved parts, attachments, and
modifications. The following definitions apply:
Approved parts or attachments are those either manufactured or pr
ovided by
Wacker Neuson.
Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
Unapproved parts, attachments, and modifications are those that do no
t
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following
consequences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
Foreword
6 wc_tx004116gb_FM10.fm
2015-CE-CT36_CT48_en_FM10.fm
EC Declaration of Conformity
Manufacturer
Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,
Menomonee Falls, Wisconsin 53051, USA
Product
Product
Product category
Product function
Item number
CT 36-5A, CT 36-8A, CT 36-8A-V, CT 36-6, CT 36-9,
CT 36-9-V, CT 48-8A, CT 48-11A, CT 48-13A-V, CT 48-9
Trowel
To smooth and finish semi-cured concrete
0620829, 0620830, 0620831, 0620832, 0620833,
0620834, 0620835, 0620836, 0620837, 0620838
Directives and Standards
We hereby declare that this product meets and complies with the relevant regulations and
requirements of the following directives and standards:
2006/42/EC, 2004/108/EC, EN12649
Authorized Person for Technical Documents
Leo Goeschka, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41,
80809 München
Menomonee Falls, WI, USA, 05.02.15
Scott V. Grahl
Manager, Product Engineering
For Wacker Neuson
Dan Domanski
Technical Director
For Wacker Neuson
Keith Herr
Managing Director
For Wacker Neuson
Original Declaration of Conformity
Table of Contents
Walk-behind Trowels
wc_bo5100019763_01TOC.fm
9
Foreword 3
EC Declaration of Conformity 7
1 Safety Information 11
1.1 Signal Words Used in this Manual ..................................................... 11
1.2 Machine Description and Intended Use ............................................. 12
1.3 Operating Safety ................................................................................ 13
1.4 Service Safety .................................................................................... 15
1.5 Operator Safety while Using Internal Combustion Engines ............... 17
2 Labels 18
2.1 Label Locations .................................................................................. 18
2.2 Label Meanings .................................................................................. 19
3 Lifting and Transporting 22
3.1 Lifting the Machine ............................................................................. 22
3.2 Transporting the Machine ................................................................... 24
4 Operation 25
4.1 Preparing the Machine for First Use ................................................... 25
4.2 Recommended Fuel ........................................................................... 25
4.3 Refueling the Machine ........................................................................ 26
4.4 Installing the Blades ........................................................................... 27
4.5 Adjusting the Handle—CT 36-5A ....................................................... 28
4.6 Installing and Adjusting the Handle .................................................... 29
4.7 Controls .............................................................................................. 31
4.8 Braking System .................................................................................. 32
4.9 Testing the Engine Control Module .................................................... 32
4.10 Position of the Operator ..................................................................... 32
4.11 Optional Weights ................................................................................ 33
4.12 Before Starting the Machine ............................................................... 33
4.13 Starting, Operating, and Stopping the Machine ................................. 34
4.14 Emergency Shutdown Procedure ....................................................... 37
Table of Contents
Walk-behind Trowels
wc_bo5100019763_01TOC.fm
10
5 General Maintenance 38
5.1 Maintaining the Emission Control System ..........................................38
5.2 Periodic Maintenance Schedule .........................................................38
5.3 Belt Replacement ...............................................................................39
5.4 Trowel Lubrication ..............................................................................40
5.5 Long-Term Storage .............................................................................40
5.6 Machine Disposal / Decommissioning ................................................41
6 Engine Maintenance 42
6.1 Periodic Maintenance Schedule: Wacker Neuson WM170 ................42
6.2 Engine Oil: Wacker Neuson WM 170 .................................................43
6.3 Periodic Maintenance Schedule: Honda GX 160 ...............................44
6.4 Oil recommendations ..........................................................................45
7 Technical Data 46
7.1 Dimensions .........................................................................................46
7.2 Engine: Honda ....................................................................................47
7.3 Engine: Wacker Neuson .....................................................................50
7.4 Trowel .................................................................................................52
7.5 Sound and Vibration Specifications ....................................................53
8 Troubleshooting 54
9 Emission Control Systems Information
and Warranty 55
9.1 Emission Control Systems Warranty Statement .................................55
10 AEM Safety Manual 57
wc_si000959gb_FM10.fm
11
Walk-Behind Trowels
Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
To avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_si000959gb_FM10.fm
12
Walk-Behind Trowels
Safety Information
1.2 Machine Description and Intended Use
This machine is a walk-behind concrete finishing trowel. The Wacker Neuson
Walk-Behind Trowel consists of a frame onto which are mounted a gasoline
engine, a fuel tank, a gearbox, and a control handle. A set of four metal blades is
connected to the gearbox and is surrounded by a ring guard. The engine rotates
the blades through the gearbox and clutch mechanism. The rotating blades ride on
the surface of curing concrete, creating a smooth finish. The operator walks behind
the machine and uses the handle to control speed and direction of the machine.
This machine is intended to be used for floating and burnishing curing concrete.
This machine has been designed and built strictly for the intended use described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty.
The following are some examples of misuse:
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Using the machine to finish inappropriate materials such as slurries, sealers, or
epoxy finishes
Operating the machine outside of factory specifications
Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operator’s Manual
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
Heat, noise, exhaust, and carbon monoxide from the engine
Chemical burns from curing concrete
Fire hazards from improper refueling techniques
Fuel and its fumes, fuel spillage from improper lifting technique
Personal injury from improper lifting techniques or operating techniques
Cutting hazards from sharp or worn blades
To protect yourself and others, make sure you thoroughly read and understand the
safety information presented in this manual before operating the machine.
wc_si000959gb_FM10.fm
13
Walk-Behind Trowels
Safety Information
1.3 Operating Safety
Operator
training
Before operating the machine:
Read and understand the operating instructions contained in all manuals
delivered with the machine.
Familiarize yourself with the location and proper use of all controls and safety
devices.
Contact Wacker Neuson for additional training if necessary.
When operating this machine:
Do not allow improperly trained people to operate the machine. People
operating the machine must be familiar with the potential risks and hazards
associated with it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
have received instruction on how to properly use the machine
are familiar with required safety devices
The machine must not be accessed or operated by:
children
people impaired by alcohol or drugs
Application
area
Be aware of the application area.
Keep unauthorized personnel, children, and pets away from the machine.
Remain aware of changing positions and the movement of other equipment and
personnel in the application area/job site.
Identify whether special hazards exist in the application area, such as toxic
gases, or unstable ground conditions, and take appropriate action to eliminate
the special hazards before using the machine.
Be aware of the application area.
Do not operate the machine in areas that contain flammable objects, fuels, or
products that produce flammable vapors.
Safety
devices,
controls, and
attachments
Only operate the machine when:
All safety devices and guards are in place and in working order.
All controls operate correctly.
The machine is set up correctly according to the instructions in the Operator’s
Manual.
The machine is clean.
The machine’s labels are legible.
To ensure safe operation of the machine:
Do not operate the machine if any safety devices or guards are missing or
inoperative.
Do not modify or defeat the safety devices.
Only use accessories or attachments that are approved by Wacker Neuson.
wc_si000959gb_FM10.fm
14
Walk-Behind Trowels
Safety Information
Safe
operating
practices
When operating this machine:
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
When operating this machine:
Do not operate a machine in need of repair.
Do not consume the operating fluids used in this machine. Depending on your
machine model, these operating fluids may include water, wetting agents, fuel
(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic fluid,
heat transfer fluid (propylene glycol with additives), battery acid, or grease.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while operating this
machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
General
operating
safety
Do not operate the machine with the beltguard missing. Exposed drive belt and
pulleys create potentially dangerous hazards that can cause serious injuries.
Never operate this machine in applications for which it is not intended.
Do not use the trowel around pop-ups in the concrete that are lower than the
lowest ring on the ring guard.
Do not use a mobile device while operating this machine.
Do not tip the machine for cleaning or for any other reason.
Do not operate the trowel with the engine control module (safety interlock)
disabled. Serious injury could occur if struck by rotating trowel due to disabling
this interlock.
wc_si000959gb_FM10.fm
15
Walk-Behind Trowels
Safety Information
1.4 Service Safety
Service training
Before servicing or maintaining the machine:
Read and understand the instructions contained in all manuals delivered
with the machine.
Familiarize yourself with the location and proper use of all controls and
safety devices.
Only trained personnel shall troubleshoot or repair problems occurring with
the machine.
Contact Wacker Neuson for additional training if necessary.
When servicing or maintaining this machine:
Do not allow improperly trained people to service or maintain the machine.
Personnel servicing or maintaining the machine must be familiar with the
associated potential risks and hazards.
Precautions
When servicing or maintaining the machine:
Read and understand the service procedures before performing any service
to the machine.
All adjustments and repairs must be completed before operating the
machine. Do not operate the machine with a known problem or deficiency.
All repairs and adjustments shall be completed by a qualified technician.
Turn off the machine before performing maintenance or making repairs.
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
Re-install the safety devices and guards after repair and maintenance
procedures are complete.
Machine
modifications
When servicing or maintaining the machine:
Use only accessories/attachments that are approved by Wacker Neuson.
When servicing or maintaining the machine:
Do not defeat safety devices.
Do not modify the machine without the express written approval of Wacker
Neuson.
Replacing parts
and labels
Replace worn or damaged components.
Replace all missing and hard-to-read labels.
When replacing electrical components, use components that are identical in
rating and performance to the original components.
When replacement parts are required for this machine, use only Wacker
Neuson replacement parts or those parts equivalent to the original in all
types of specifications, such as physical dimensions, type, strength, and
material.
wc_si000959gb_FM10.fm
16
Walk-Behind Trowels
Safety Information
Cleaning
When cleaning and servicing the machine:
Keep the machine clean and free of debris such as leaves, paper, cartons,
etc.
Keep the labels legible.
When cleaning the machine:
Do not clean the machine while it is running.
Never use gasoline or other types of fuels or flammable solvents to clean
the machine. Fumes from fuels and solvents can become explosive.
Personal
Protective
Equipment (PPE)
Wear the following Personal Protective Equipment (PPE) while servicing or
maintaining this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
In addition, before servicing or maintaining the machine:
Tie back long hair
Remove all jewelry (including rings)
Safe service
practices
Do not crank a flooded engine with the spark plug removed on gasoline-
powered engines. Fuel trapped in the cylinder will squirt out the spark plug
opening.
Do not test for spark on gasoline-powered engines if the engine is flooded or
the smell of gasoline is present. A stray spark could ignite the fumes.
Disconnect the spark plug on machines equipped with gasoline engines,
before servicing, to avoid accidental start-up.
Do not remove blades while the machine is hanging overhead.
Only change the blades when the machine is supported securely.
Handle blades carefully. The blades can develop sharp edges which can
cause serious cuts.
After use
Stop the engine when the machine is not being operated.
Close the fuel valve on engines equipped with one when the machine is not
being operated.
Ensure that the machine will not tip over, roll, slide, or fall when not being
operated.
Store the machine properly when it is not being used. The machine should
be stored in a clean, dry location out of the reach of children.
wc_si000959gb_FM10.fm
17
Walk-Behind Trowels
Safety Information
1.5 Operator Safety while Using Internal Combustion Engines
Operating safety
When running the engine:
Keep the area around the exhaust pipe free of flammable materials.
Check the fuel lines and the fuel tank for leaks and cracks before starting the
engine. Do not run the machine if fuel leaks are present or the fuel lines are
loose.
When running the engine:
Do not smoke while operating the machine.
Do not run the engine near sparks or open flames.
Do not touch the engine or muffler while the engine is running or
immediately after it has been turned off.
Do not operate a machine when its fuel cap is loose or missing.
Do not start the engine if fuel has spilled or a fuel odor is present. Move the
machine away from the spill and wipe the machine dry before starting.
Refueling safety
When refueling the engine:
Clean up any spilled fuel immediately.
Refill the fuel tank in a well-ventilated area.
Re-install the fuel tank cap after refueling.
Use suitable tools for refueling (for example, a fuel hose or funnel).
When refueling the engine:
Do not smoke.
Do not refuel a hot or running engine.
Do not refuel the engine near sparks or open flames.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
Exhaust gas from the engine contains carbon monoxide, a deadly poison.
Exposure to carbon monoxide can kill you in minutes.
NEVER operate the machine inside an enclosed area, such as a tunnel, unless
adequate ventilation is provided through such items as exhaust fans or hoses.
wc_si000960gb_FM10.fm
18
Walk-Behind Trowels
Labels
2 Labels
2.1 Label Locations
wc_gr010351
J
C
H
G
D
F
L
B
E
A
M
K
wc_si000960gb_FM10.fm
19
Walk-Behind Trowels
Labels
2.2 Label Meanings
A
Engine stop button:
Press to stop engine.
B
Variable speed throttle
C
WARNING
Always wear hearing and eye protection when
operating this machine.
D
DANGER
Asphyxiation hazard.
Engines emit carbon monoxide.
Do not run the machine indoors or in an
enclosed area.
NEVER use inside a home or garage, EVEN
IF doors and windows are open.
Only use OUTSIDE and far away from
windows, doors, and vents.
Read the Operator’s Manual.
No sparks, flames, or burning objects near the
machine.
Stop the engine before refueling.
Use only clean, filtered fuel.
178745
178745
118085118085
WARNINGWARNING
AVERTISSEMENTAVERTISSEMENT
ADVERTENCIAADVERTENCIA
WARNUNGWARNUNG
117034
STOP
PELIGRO
DANGER
GEFAHR
DANGER
178715
STOPSTOP
wc_si000960gb_FM10.fm
20
Walk-Behind Trowels
Labels
E
NOTICE
Lifting point
F
CAUTION
Read and understand the supplied Operator’s
Manual before operating this machine. Failure to
do so increases the risk of injury to yourself and
others.
G
WARNING
Hot surface
H
WARNING
Hand injury if caught in moving belt.
Always replace beltguard.
J
Use only Glygoyle 460 gear oil in gearbox.
178709178709
178714
117039
ADVERTENCIA
ADVERTENCIA
AVERTISSEMENT
AVERTISSEMENT
WARNING
WARNING
178712
178712
WACKER NEUSON
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136

Wacker Neuson CT48-8A EU Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues