Wacker Neuson P35A Manuel utilisateur

Operator’s Manual

Notice d'emploi

Wet Screed

Lissoir Humide

P35A

Type P35A

Document 5000192693

Date

0516

Version 05

Language EN-FR

5000192693

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

P 35A Foreword

wc_tx003251gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machines

covered in

this manual

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Machine Item Number

P 35A 0620956, 0620957, 0620958

wc_gr010231

Serial Number:

Foreword P 35A

4 wc_tx003251gb.fm

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and main-

tain the above Wacker Neuson model(s). For your own safety and to reduce the

risk of injury, carefully read, understand, and observe all instructions described

in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

 The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker Neu-

son service center according to written instructions published by Wacker Neu-

son.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Original Declaration of Conformity

2016-CE-P35A_en_FM10.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

P35A

Vibratory Concrete Screed

To level freshly poured concrete

5000620956, 5000620957, 5000620958

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2014/30/EU, EN 12649

Authorized Person for Technical Documents

Leo Goeschka, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41,

80809 München

Menomonee Falls, WI, USA, 09.05.16

Keith Herr

Vice President and Managing Director

For Wacker Neuson

Scott Grahl

Manager, Product Engineering

For Wacker Neuson

Jeff Volden

Director, Product Engineering

For Wacker Neuson

Table of Contents

P 35A

wc_bo5000192669_05TOC.fm

7

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Operating Safety ................................................................................ 11

1.4 Operator Safety while Using Internal Combustion Engines ............... 12

1.5 Service Safety .................................................................................... 13

2 Labels 15

2.1 Label Locations .................................................................................. 15

2.2 Label Meanings .................................................................................. 15

3 Lifting and Transporting 17

4 Operation 18

4.1 Control / Component Locations .......................................................... 18

4.2 Preparing the Machine for First Use ................................................... 19

4.3 Position of the Operator ..................................................................... 19

4.4 Recommended Fuel ........................................................................... 20

4.5 Before Starting ................................................................................... 20

4.6 Starting ............................................................................................... 21

4.7 Stopping ............................................................................................. 21

4.8 Operation ............................................................................................ 22

4.9 Exciter Adjustment ............................................................................. 24

4.10 Adjusting the Handle Height ............................................................... 25

4.11 Kick-Stand .......................................................................................... 25

4.12 Emergency Shutdown Procedure ....................................................... 25

Table of Contents

P 35A

wc_bo5000192669_05TOC.fm

8

5 Maintenance 26

5.1 Maintaining the Emission Control System ...........................................26

5.2 Periodic Maintenance Schedule ..........................................................26

5.3 Engine Oil ............................................................................................27

5.4 Air Cleaner ..........................................................................................28

5.5 Spark Plug ...........................................................................................29

5.6 Cleaning the Machine ..........................................................................30

5.7 Long-Term Storage .............................................................................30

5.8 Troubleshooting ...................................................................................31

6 Technical Data 32

6.1 Engine .................................................................................................32

6.2 Blades .................................................................................................33

6.3 Dimensions ..........................................................................................33

6.4 Vibration Measurements .....................................................................34

7 Emission Control Systems Information and Warranty 35

7.1 Emission Control Systems Warranty Statement .................................35

wc_si000748gb.fm

9

P 35A Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000748gb.fm

10

Safety Information P 35A

1.2 Machine Description and Intended Use

This machine is a vibratory concrete screed. The Wacker Neuson Wet Screed

consists of a gasoline engine, a fuel tank, a metal blade, an eccentric weight

positioned at the center of the metal blade, and a control handle. The gasoline

engine spins the eccentric weight through a drive shaft, producing vibrations that

travel the length of the metal blade. The operator uses the control handle to pull the

machine across uncured concrete.

This machine is intended to be used for striking off uncured concrete slabs with or

without the support of grade stakes or forms.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Engaging the screed when not on uncured concrete

 Operating the machine on non-compactable surfaces, such as asphalt or cured

concrete

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Chemical burns from the curing concrete

 Fire hazards from improper refueling techniques

 Fuel and its fumes, fuel spillage from improper lifting technique

 Personal injury from improper lifting techniques or operating techniques

 Excessive vibration by holding the blade

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_si000748gb.fm

11

P 35A Safety Information

1.3 Operating Safety

Operator

training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals

delivered with the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Contact Wacker Neuson for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Application

area

Be aware of the application area.

 Keep unauthorized personnel, children, and pets away from the machine.

 Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

Be aware of the application area.

 Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

 All safety devices and guards are in place and in working order.

 All controls operate correctly.

 The machine is set up correctly according to the instructions in the Operator’s

Manual.

 The machine is clean.

 The machine’s labels are legible.

To ensure safe operation of the machine:

 Do not operate the machine if any safety devices or guards are missing or

inoperative.

 Do not modify or defeat the safety devices.

 Only use accessories or attachments that are approved by Wacker Neuson.

wc_si000748gb.fm

12

Safety Information P 35A

Safe

operating

practices

When operating this machine:

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

When operating this machine:

 Do not operate a machine in need of repair.

 Do not consume the operating fluids used in this machine. Depending on your

machine model, these operating fluids may include water, wetting agents, fuel

(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic fluid,

heat transfer fluid (propylene glycol with additives), battery acid, or grease.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

After Use

 Stop the engine when the machine is not being operated.

 Close the fuel valve, if equipped, when machine is not being operated.

 Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

 Store the machine in a clean, dry location out of the reach of children.

wc_si000748gb.fm

13

P 35A Safety Information

1.4 Service Safety

Service

training

Before servicing or maintaining the machine:

 Read and understand the instructions contained in all manuals delivered with

the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

 Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

 Do not allow improperly trained people to service or maintain the machine.

Personnel servicing or maintaining the machine must be familiar with the

associated potential risks and hazards.

Precautions

Follow the precautions below when servicing or maintaining the machine.

 Read and understand the service procedures before performing any service to

the machine.

 All adjustments and repairs must be completed before operation. Do not

operate the machine with a known problem or deficiency.

 All repairs and adjustments shall be completed by a qualified technician.

 Turn off the machine before performing maintenance or making repairs.

Machine

modifications

When servicing or maintaining the machine:

 Use only accessories/attachments that are approved by Wacker Neuson.

When servicing or maintaining the machine:

 Do not defeat safety devices.

 Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing

parts and

labels

 Replace worn or damaged components.

 Replace all missing and hard-to-read labels.

 When replacing electrical components, use components that are identical in

rating and performance to the original components.

 When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

Cleaning

When cleaning and servicing the machine:

 Keep the machine clean and free of debris such as leaves, paper, cartons, etc.

 Keep the labels legible.

When cleaning the machine:

 Do not clean the machine while it is running.

 Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

wc_si000748gb.fm

14

Safety Information P 35A

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

Safe service

practices

 Do not crank a flooded engine with the spark plug removed on gasoline-

powered engines. Fuel trapped in the cylinder will squirt out the spark plug

opening.

 Do not test for spark on gasoline-powered engines if the engine is flooded or the

smell of gasoline is present. A stray spark could ignite the fumes.

 Handle blades carefully. The blades can develop sharp edges which can cause

serious cuts.

wc_si000748gb.fm

15

P 35A Safety Information

1.5 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

 Keep the area around exhaust pipe free of flammable materials.

 Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

When running the engine:

 Do not smoke while operating the machine.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Reinstall the fuel tank cap after refueling.

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

 Use suitable tools for refueling (for example, a fuel hose or funnel).

 Do not refuel if the machine is positioned in a truck fitted with a plastic bed liner.

Static electricity can ignite the fuel or fuel vapors.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

wc_si000749gb.fm

16

Labels P 35A

2 Labels

2.1 Label Locations

C

A

E

D

B

wc_gr008018

wc_si000749gb.fm

17

P 35A Labels

2.2 Label Meanings

A WARNING

To reduce the risk of hearing loss and

eye injury, always wear hearing

protection and eye protection when

operating this machine.

B WARNING

Hot surface

C DANGER

Asphyxiation hazard

 Engines emit carbon monoxide.

 Do not run the machine indoors or in

an enclosed area unless adequate

ventilation, through such items as

exhaust fans or hoses, is provided.

 Read the Operator’s Manual. No

sparks, flames, or burning objects near

the machine. Stop the engine before

refueling.

D This machine may be covered by one or

more patents.

0178715

STOP

wc_si000749gb.fm

18

Labels P 35A

E WARNING

Rotating machinery! Do not reach inside

machine with engine running.

wc_tx003252gb.fm

19

P 35A Lifting and Transporting

3 Lifting and Transporting

To lift and transport the machine:

1. Loosen the screws (a) and fold down the upper guide handle (b). Tighten the

screws to hold the upper guide handle in position.

2. Use the lifting handle (c) at the base to lift and transport the machine.

wc_gr010850

c

a

b

wc_tx003253gb.fm

20

Operation P 35A

4 Operation

4.1 Control / Component Locations

Ref Description Ref Description

1 Adjustable handle 5 Kickstand

2 Adjustable handle grips 6 Lifting handle

3 Throttle control 7 Blade

4 Fuel tank — —

wc_gr008019

5

4

1

7

6

2

3

La page charge ...

Wacker Neuson P35A Manuel utilisateur

Ce manuel convient également à

Wacker Neuson P35A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents