Marshalltown Speed Striker 2.0 Le manuel du propriétaire

Marque: Marshalltown

Modèle: Speed Striker 2.0

Taper: Le manuel du propriétaire

SPEED STRIKERTM . POWER SCREED

Part# STRIKER2.0 | EDI# 33007

104 S. 8th Ave. | Marshalltown, IA

Phone 800-888-0127 / 641-753-0127 | Fax 800-477-6341 / 641-753-6341

www.MARSHALLTOWN.com

2 of 14 104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.com WS3747

TABLE OF CONTENTS

Safety Precautions ......................................................................................................................................................................................... 2

Warranty ........................................................................................................................................................................................................... 3

Common Components ...................................................................................................................................................................................4

Installing Handle Bars & Kickstand .............................................................................................................................................................. 5

Attaching Blade ............................................................................................................................................................................................... 5

Installing Throttle Cable ..............................................................................................................................................................................6-7

Machine Adjustments ....................................................................................................................................................................................8

Technical Data/Capacities ............................................................................................................................................................................9

Maintenance .....................................................................................................................................................................................................9

Parts Breakdown ......................................................................................................................................................................................10-11

How to Wet Screed ....................................................................................................................................................................................... 12

How to Screed Form to Form ..................................................................................................................................................................... 13

How to Operate.............................................................................................................................................................................................. 14

Operating on Wet Concrete ........................................................................................................................................................................ 15

SAFETY PRECAUTIONS

DANGER!

• DANGER or

WARNING!

WARNING safety signs are located near specific hazards.

CAUTION!

• General precautions are listed on CAUTION safety signs.

This machine was built with user safety in mind, however, it can present hazards if improperly operated and serviced.

Follow operating instructions carefully and use good judgement when operating!

If you have questions about operating or servicing this equipment, please contact your Marshalltown distributor or

Marshalltown Company at 800-888-0127 or 641-753-0127.

ALWAYS

• Always stop engine between loads of concrete

• Always screed while walking backwards

• Always clearly mark and be aware of all grade pins,

form stakes or other trip hazards

• Always follow all safety warnings and labels of the

engine manufacturer

• Always read and understand the owners manual of

the engine manufacturer

• Always wear approved hearing, eye and breathing

protection

• Always use form oil to coat blade or other parts

susceptible to concrete build up (avoiding electrical

connections) before each use

• Always properly secure screed before transporting

• Always follow recommended maintenance schedules

• Always make sure all connections and fasteners are

tight before every use

• Always always make sure engine is in "OFF" position

when servicing or not in use

• Always use in a well ventilated area

• Always keep Speed Striker™ and engine manual handy

on the job site

• Always replace parts as they become damaged or worn

NEVER

• Never operate screed without all parts and safety

covers correctly attached

• Never allow children to operate

• Never operate under the influence of drugs or alcohol

• Never use screed for anything other than its

intended purpose

• Never set eccentric weights to where excessive

vibration occurs at low RPM (weights too far open)

• Never set eccentric weights to where it takes excessive

RPM to make weights vibrate (weights too far closed)

• Never allow engine to run unattended or idle on

top of wet concrete

• Never place concrete higher than the leading

“curl edge” of the blade

• Never fill gas tank while engine is running

• Never start engine near spilt fuel

• Never fill gas tank, operate, or service screed

near open flame

• Never use parts or blades from other manufacturers

• Never service a hot engine

• Never operate without proper training

• Never spray water or other liquid on a hot engine

3 of 14

104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.comWS3747

WARRANTY

Marshalltown Company (the Company) warrants, that for a period of twelve (12) months from the date of purchase, it will

replace or repair, free of charge, for the original retail purchaser only, any part or parts, manufactured by the Company, found

upon examination by the Company or its assigned representatives, to be defective in material or workmanship or both. All

transportation charges for parts submitted for replacement or repair under this warranty must be borne by the original retail

purchaser. This is the exclusive remedy under this warranty.

Failure by the original retail purchaser to install, maintain and operate said equipment in accordance with good industry

practices, or failure to comply with the specific recommendations of the Company set forth in the owner’s manual, shall

render this warranty null and void. The Company shall not be liable for any repairs, replacements, or adjustments to the

equipment or any costs for labor performed by the purchaser without the Company’s prior written approval. The effects of

corrosion, erosion and normal wear and tear are specifically excluded from this warranty.

THE COMPANY MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER, EXPRESSED OR

IMPLIED, EXCEPT THAT OF TITLE. ALL IMPLIED WARRANTIES, INCLUDING ANY WARRANTY OF MERCHANTABILITY AND

FITNESS FOR PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIABILITY FOR CONSEQUENTIAL AND INCIDENTAL

DAMAGES UNDER ANY AND ALL WARRANTIES, OTHER CONTRACTS, NEGLIGENCE, OR OTHER TORTS IS EXCLUDED TO

THE EXTENT EXCLUSION IS PERMITTED BY LAW.

Notwithstanding the above, any legal claim against the Company shall be barred if legal action thereon is not commenced

within twenty–four (24) months from the date of purchase or delivery, whichever occurs last. This warranty constitutes the

entire agreement between the Company and the original retail purchaser and no representative or agent is authorized to

alter the terms of same without expressed written consent of the Company.

4 of 14 104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.com WS3747

COMMON COMPONENTS

REF # DESCRIPTION REF  DESCRIPTION

1 START/STOP SWITCH 10 DRIVE SHAFT

2 ENGINE 11 VIBRATION DAMPENERS

3 RECOIL STARTER 12 BLADE

4 OIL CAP 13 ECCENTRIC WEIGHT COVER

5 GAS CAP 14 FRAME

6THROTTLE LEVER 15 BOARD MOUNTING PLATE

7 HANDLE BAR MOUNTING BLOCKS  THROTTLE CABLE

8 HANDLE BARS 17 AIR FILTER

9 KICKSTAND

11 13

5 of 14

104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.comWS3747

ASSEMBLY INSTRUCTIONS

Step 1 – Remove the 4 hex screws (A) that hold down

the two handle mounting blocks.

Step 2 – Slide kickstand arm onto kickstand end and

fasten with nut & bolt (B) as shown.

Step 4 – Making sure all mounting block and frame holes

are aligned, insert hex screws and tighten with ⁄"

wrench or socket.

Step 3 – Place handle bars into mounting blocks, making

sure handle bars are centered evenly across the

mounting blocks.

INSTALLING HANDLE BARS AND KICKSTAND

ATTACHING BLADE

Attach blade as shown, making sure the blade is

positioned on the “back side” of the base casting with

blade spacers (A) on both sides of the blade.

Make sure bolts are tight before each use.

! !

Assembly is easy, following these steps:

6 of 14 104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.com WS3747

INSTALLING THROTTLE CABLE

Step 1 – Remove carburetor cover by

pressing clips.

Step 3 – Fasten the throttle cable as

shown. Make sure there is a nut on

each side of plastic fitting. Make sure

the cable does not work itself out of

the plastic fitting while tightening.

Step 2 – The throttle has a rotating

silver peg (A) with a slot on one side of

it. One end of the throttle cable has a

metal barrel (B) that fits into this slot.

Insert barrel into the slot so when the

throttle cable is pulled, it will pull the

throttle open (toward the base plate

of the screed).

MACHINE ADJUSTMENTS

CAUTION

Always make sure engine is stopped with switch in "OFF" position before making adjustments.

HANDLES

Your Speed Striker™ screed handle can be adjusted for a

customized fit.

The height of the handle can be adjusted right below the

motor.

ADJUSTABLE

7 of 14

104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.comWS3747

Check and retighten eccentric weights Every 10 hours or every month

Check oil level Before each use

Change engine oil First month or 10 hrs. - 6 mo. or 50 hrs after

Check fuel level Before each use

Inspect air filter Before each use

Replace air filter Every 25 hours or every 3 months

Spark plug - check and adjust Every 100 hours or 1 year

Spark plug - replace Every 300 hours or 2 years

Cooling fins Every 50 hours

Electronic Connections Before each use

Check Nuts and bolts Before each use

Replace nuts and bolts As necessary

Model Number STRIKER2.0

Drive System Flexible Shaft

Weight 28.5 lbs. (12.9 kg)

Blade Lengths 4, 6, 8, 10, 12, 14, 16'

1.2, 1.8, 2.4, 3, 3.7, 4.3, 4.9M

Blade Weight 1.85 Lb./ft. 2.75(kg/m)

Engine Type 4-stroke, overhead cam, single cylinder

Engine Make Honda

Engine Model GX35

Engine Horsepower 1.3 hp (1.0kW) @ 7,000 rpm

Engine Displacement 2.18 cu-in (35.8cm3)

Spark Plug CM5H (NGK)

CMR5H (NGK)

Spark Plug Gap 0.60 - 0.70mm

(0.024 - 0.028 in)

Engine Speed - idle 3,100 ± 200 rpm

Oil Type - Engine SAE 10W-30 (refer to engine manual)

Oil Capacity - Engine 0.11 qt (3.5 oz., 0.10 L)

Fuel Type Pump octane rating 86 or higher (refer to engine manual)

Fuel Tank Capacity 0.166 US gal (0.63 L)

TECHNICAL DATA/CAPACITIES

CAUTION

Your Speed StrikerTM ships with a pre-measured bottle of oil (3.5 oz).

Do not at anytime have more than 3.5 oz. of oil in the engine. Too much oil will foul

out the spark plug resulting in an engine that is hard to start and keep running.

! !

MAINTENANCE

8 of 14 104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.com WS3747

REPLACEMENT PARTS INDEX

EDI PART# DESCRIPTION DETAILS INCLUDED

13309 13309 GRIPS 43

13310 ENG-HONDA HONDA ENGINE 1, 41

13312 13312 THROTTLE LEVER 42

13313 13313 THROTTLE CABLE 5

13315 13315 HANDLEBAR CLAMPS W/HARDWARE 2, 33

13316 13316 HANDLEBAR CLAMP HARDWARE ONLY 33

13317 13317 ON/OFF SWITCH W/WIRES 6, 17

13318 13318 ON/OFF SWITCH WIRES 17

13324 13324 CLUTCH 16, 41

13330 13330 ECCENTRIC WEIGHT & HARDWARE 8, 9, 11, 12, 29

13331 13331 ECCENTRIC WEIGHT HARDWARE ONLY 9, 11, 12, 29

13333 13333 BLADE LOCKING HARDWARE 18, 30, 39, 40

13334 13334 DRIVE SHAFT 15

33009 STRIKER2.0FR REPLACEMENT FRAME 2.0 25, 26, 33, 34, 35

32859 SW200MB MACHINE BASE 2.0 4

32860 SW200VD VIBRATION DAMPENING KIT 7, 34

32861 SW200KICK KICKSTAND 20, 21, 22, 23, 24, 32,

33, 34, 36, 37, 38, 45

32862 SW200EC ECCENTRIC COVER WITH HARDWARE 27, 31

13323 13323 DRIVE TRAIN 10, 13, 14, 16, 28

PARTS BREAKDOWN

BLADE SIZE CHART

EDI Part # SIZE-FT. SIZE-M

32403 32403 4 1.2

32404 32404 4.5 1.37

32405 32405 6 1.8

32406 32406 8 2.4

32407 32407 10 3.0

32408 32408 12 3.7

32409 32409 14 4.3

32410 32410 16 4.9

32411 32411 16 4.9

DET. QTY. DESCRIPTION

1 1 GX35 HONDA MOTOR

2 4 HANDLEBAR CLAMP

3 1 HANDLEBAR ASSEMBLY

4 1 MACHINE BASE

5 1 THROTTLE CABLE (NOT PICTURED)

6 1 ON/OFF SWITCH

7 4 VIBRATION ISOLATOR

8 1 ECCENTRIC WEIGHT

9 1 LOCK WASHER

10 1 ECCENTRIC SHAFT

11 1 ECCENTRIC TIGHTENING CAP BOLT

12 1 WEIGHT TIGHTENING CAP

13 1 LOWER BEARING HOUSING

14 1 COUPLING DRIVE SHAFT

15 1 DRIVE SHAFT (NOT PICTURED)

16 1 CLUTCH

17 1 ON/OFF SWITCH WIRES

18 2 BLADE MOUNTING LOCKNUT

19 1 BLADE

20 1 KICKSTAND END

21 1 KICKSTAND ARM

22 2 KICKSTAND EYEBOLT

23 1 KICKSTAND BUMPER

24 1 EXTENSION SPRING

25 1 LOWER FRAME

26 1 ENGINE MOUNTING PLATE

27 1 ECCENTRIC COVER CAP

28 3 DRIVETRAIN MOUNTING BOLT

29 1 ECCENTRIC WEIGHT LOCKNUT

30 2 BLADE MOUNTING BOLT

31 4 ECCENTRIC SCREW CAP

32 2 KICKSTAND BRACKET MOUNTING BOLT

33 16 ⁄" -20 BOLT

34 16 ⁄" -20 LOCKNUT

35 2 CAP PLUG

36 1 KICKSTAND BRACKET, REAR

37 1 KICKSTAND BRACKET, FRONT

38 5 #10-24 LOCKNUT

39 4 BLADE MOUNTING WASHER

40 2 BLADE MOUNTING LOCK WASHER

41 4 ENGINE MOUNTING SCREW

42 1 THROTTLE LEVER

43 2 HANDLEBAR GRIP

44 2 BLADE SPACER

45 1 KICKSTAND STOP BOLT

9 of 14

104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.comWS3747

PARTS BREAKDOWN

DETAIL A

SCALE 1 / 5

40 39

10 of 14 104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.com WS3747

HOW TO WET SCREED

SETTING ELEVATION OF SLAB

• Use grade pins (A) to set height of slab in the middle of

the pour.

• Chalk line or expansion joint sets elevation around walls.

• Form boards set elevation where there are no walls.

Blade Length

12-18 inches

A A

12" - 18"

A A

MAKING WET PADS

1. Using hand float, make wet pads around all grade pins (A).

NOTE: Make sure all wet pad distances are shorter than

the length of blade being used.

2. Use blade to stretch from wet pad to wet pad

forming rows (B).

3. Once rows are formed, run screed blade off of the two

rows leveling the previously untouched concrete (C) in

between.

NOTE: Height of concrete in area (C) must be slightly

higher than wet pad rows (B) prior to striking off.

Once floated, wet pads (B) and concrete (C) will all be

the same height.

11 of 14

104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.comWS3747

HOW TO SCREED FORM TO FORM

Length of blade should overlap form boards on both

sides of the pour.

Keep bottom of blade as flat as possible while striking

off of forms.

To ensure the longest possible blade life, use the

lowest possible vibration setting in relationship to the

slump of concrete being used.

Width of Screed Blade

Width of Form

Form Board

ELEVATED

TRAILING EDGE

Form Board

ELEVATED

LEADING EDGE

KEEP SCREED BLADE FLAT

Form Board

An elevated trailing edge may provide an area for

concrete to build up resulting in a slab elevation that

is too high.

An elevated leading edge can trap rocks between the

blade and forms resulting in a slab elevation that is too

high.

12 of 14 104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.com WS3747

HOW TO OPERATE

FUEL AND OIL

Make sure gas tank has plenty of 86 octane or higher gasoline.

Your 4 stroke Honda engine uses straight gasoline, NEVER

USE A GAS/OIL MIX. Empty entire bottle of provided Honda

engine oil into crank case. The maximum oil capacity is 3.5 oz.

NEVER OVERFILL.

STARTING

1. On a cold engine, move choke lever to CLOSED

position. To restart a warm engine leave choke in

OPEN position

2. Press priming bulb repeatedly until fuel can be

seen in the clear-plastic fuel-return tube.

3. Press On/Off Switch to the On Position.

4. Pull the starter grip lightly until you feel resistance,

then pull briskly. Repeat until engine starts.

5. If the choke lever was moved to the CLOSED

position to start the engine, gradually move it to

the OPEN position as the engine warms up.

RESTARTING A WARM ENGINE

1. Leave the choke lever in the OPEN position.

2. If there is no fuel in the clear-plastic fuel-return

tube, press priming bulb repeatedly

until fuel can be seen in the tube.

3. Press On/Off Switch to the On Position

4. Pull the starter grip lightly until you feel resistance,

then pull briskly. Repeat until engine starts.

CLOSED

OPEN

13 of 14

104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.comWS3747

Once the engine is warm and running by itself with the choke OPEN you can begin screeding concrete.

For specific instructions on Wet Screeding and Form to Form screeding please see pages 12 and 13.

1. Begin by placing concrete within your forms slightly higher than the forms themselves.

2. Place screed on top of concrete and start engine.

3. Increase engine RPM until the clutch engages causing the screed to vibrate.

4. Walking backwards, begin screeding concrete (see page 12 for Wet Screeding or Page 13 for Form to Form screeding).

5. Your throttle lever does not require constant contact, but you can adjust RPM and vibration to accommodate wet or

dry concrete. Dry or low slump concrete may require more vibration to level and screed.

6. Continue moving backwards while keeping concrete placed in front of the blade. The roll back feature of the blade will

keep help keep concrete from sliding over the blade. Concrete placed too high may slide over the board! This could

make the screed too hard to pull and result in a slab that is out of level.

OPERATING ON WET CONCRETE

DO NOT OVER VIBRATE CONCRETE

The following are signs of too much vibration:

• Excessive concrete splatter

• Blade sinking below wet pads

• Ripple or “wake marks” following the blade

• Concrete easily sliding underneath form boards causing dips along the form edge

Always remember, the less vibration the better. Use only enough vibration to be able to

comfortably pull screed backwards, leaving a smooth, level surface.

104 S. 8th Ave., Marshalltown, IA

Phone 800-888-0127 / 641-753-0127

Fax 800-477-6341 / 64 1-753-6341

www.MARSHALLTOWN.com

WS3747

SPEED STRIKERTM . LA ENRASADORA MOTORIZADA

PIEZA#STRIKER2.0 | EDI#33007

104 S. 8th Ave. | Marshalltown, IA

Teléfono 800-888-0127 / 641-753-0127 | Fax 800-477-6341 / 641-753-6341

www.MARSHALLTOWN.com

2 de 14 WS#3747104 S. 8th Ave. Marshalltown, IA Teléfono 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.com

CONTENIDO

Precauciones de Seguridad ..........................................................................................................................................................................2

Garantía .............................................................................................................................................................................................................3

Componentes Comunes ................................................................................................................................................................................4

Instalación de la BARRA de las manijas y de la barra de apoyo .............................................................................................................5

Instalación de la hoja ......................................................................................................................................................................................5

Instalación del cable del acelerador .........................................................................................................................................................6-7

Ajustes de la máquina ....................................................................................................................................................................................8

Datos y características técnicos ..................................................................................................................................................................9

Mantenimiento .................................................................................................................................................................................................9

Descripción de las piezas .......................................................................................................................................................................10-11

Cómo apisonar en húmedo ......................................................................................................................................................................... 12

Cómo apisonar de encofrado a encofrado .............................................................................................................................................. 13

Operación ....................................................................................................................................................................................................... 14

Operación en concreto húmedo ................................................................................................................................................................ 15

Este equipo fue construido pensando en la seguridad del usuario; sin embargo, puede haber riesgos si se opera o se le

da servicio inadecuadamente. Siga detenidamente las instrucciones de operación ¡y use su buen juicio al operar la unidad!

Si tiene preguntas acerca de la operación o servicio de este equipo, comuníquese con su distribuidor Marshalltown o con

Marshalltown Company al teléfono 800-888-0127 o al 641-753-0127.

SIEMPRE

• Siempre apague el motor entre cargas de concreto

• Siempre distribuya el concreto caminando hacia atrás

• Siempre marque claramente y manténgase alerta a la estacas de nivel,

estacas de encofrado y otros riesgos de tropezones

• Siempre obedezca todas las advertencias y etiquetas de seguridad del

fabricante del motor

• Siempre lea y entienda el manual del propietario proporcionado por el

fabricante del motor

• Siempre use protectores auditivos, oculares y respiratorios apropiados

• Siempre use aceite de moldes para recubrir la hoja u otras piezas

susceptibles a la acumulación de concreto (evitando las conexiones

eléctricas) antes de cada uso

• Siempre fije adecuadamente el vibrador antes de transportarlo

• Siempre siga los programas de mantenimiento recomendados

• Siempre asegúrese de que todas las conexiones y sujetadores estén

firmes antes de cada uso

• Siempre asegúrese de que el motor esté apagado cuandohaga el

servicio o cuando no lo use

• Siempre use el vibrador en un área bien ventilada

• Siempre mantenga el manual del vibrador Speed Striker™ y el del motor

a la mano en el sitio de trabajo

• Siempre reemplace las piezas tan pronto como se dañen o desgasten

NUNCA

• Nunca opere el vibrador cuando le falten partes o no tenga

las cubiertas de seguridad correctamente instaladas

• Nunca permita que los niños operen la unidad

• Nunca opere la unidad bajo la influencia de drogas o alcohol

• Nunca use el vibrador para nada que no sea su uso indicado

• Nunca coloque pesos excéntricos donde ocurra vibración excesiva a

bajas RPM (pesos demasiado separados)

• Nunca coloque pesos excéntricos en áreas en las que se requieren RPM

excesivas para que los pesos vibren (pesos demasiado cerca)

• Nunca permita que el motor funcione desatendido o a marcha en vacío

sobre concreto húmedo.

• Nunca coloque el concreto más arriba del “borde rizado” frontal

de la hoja

• Nunca llene el tanque de gasolina con el motor funcionando

• Nunca arranque el motor cerca de derrames de combustible

• Nunca llene el tanque de gasolina, no opere ni dé servicio al vibrador

cerca de llamas expuestas

• Nunca use piezas ni hojas de otros fabricantes

• Nunca dé servicio a un motor caliente

• Nunca opere la unidad si no tiene la capacitación adecuada

• Nunca rocié agua o líquidos sobre un motor caliente

• Los letreros de seguridad de PELIGRO o ADVERTENCIA se encuentran ubicados cerca

de riesgos específicos.

• Las medidas de seguridad generales se enumeran en los letreros de seguridad de

PRECAUCIÓN.

3 de 14

WS#3747 104 S. 8th Ave. Marshalltown, IA Teléfono 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.com

GARANTÍA

Marshalltown Company (la Compañía) garantiza que por un periodo de doce (12) meses a partir de la fecha de compra,

reemplazará o reparará gratuitamente, sólo al comprador minorista original, todas las piezas o partes fabricadas por la

Compañía que, al ser examinadas por la Compañía o sus representantes asignados, se determine que tienen defectos en

los materiales, la mano de obra o ambos. Todos los cargos de transportación de las piezas enviadas para su reemplazo o

reparación bajo esta garantía deberán ser pagados por el comprador minorista original. Éste es el recurso exclusivo bajo

esta garantía.

Si el comprador minorista original no instala, mantiene y opera dicho equipo de acuerdo con las buenas prácticas en la

industria, o si no sigue las recomendaciones específicas de la Compañía indicadas en el manual del propietario, esta garantía

se anulará e invalidará. La Compañía no será responsable de ninguna reparación, reemplazo o ajuste del equipo, ni de ningún

costo por la mano de obra que realice el comprador sin la aprobación por escrito previa de la Compañía. Los efectos de la

corrosión, erosión y desgaste normal se excluyen específicamente de esta garantía.

LA COMPAÑÍA NO HACE NINGUNA OTRA GARANTÍA NI DECLARACIÓN DE ABSOLUTAMENTE OTRA CLASE, EXPRESA O

IMPLÍCITA, SALVO LA ANTERIOR. POR MEDIO DE LA PRESENTE SE RENUNCIA A TODAS LAS GARANTÍAS IMPLÍCITAS,

INCLUSO CUALQUIER GARANTÍA DE COMERCIALIZACIÓN E IDONEIDAD PARA UN PROPÓSITO PARTICULAR. SE EXCLUYE

LA RESPONSABILIDAD POR DAÑOS INCIDENTALES Y RESULTANTES BAJO CUALQUIERA Y TODAS LAS GARANTÍAS,

OTROS CONTRATOS, NEGLIGENCIA Y OTROS PERJUICIOS, EN LA MEDIDA QUE TAL EXCLUSIÓN DE LA EXTENSIÓN SEA

PERMITIDA POR LA LEY.

No obstante lo antedicho, cualquier reclamación legal contra la Compañía será desestimada si la acción legal sobre la misma

no comienza en un plazo de veinticuatro (24) meses a partir de la fecha de compra o de la entrega, lo que ocurra después.

Esta garantía constituye todo el acuerdo entre la Compañía y el comprador minorista original, y ningún representante o

agente tiene autoridad para alterar los términos de la misma sin el consentimiento expreso por escrito de la Compañía.

4 de 14 WS#3747104 S. 8th Ave. Marshalltown, IA Teléfono 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.com

REF # DESCRIPCIÓN REF  DESCRIPCIÓN

1 INTERRUPTOR DE ARRANQUE Y PARADA 10 EJE DEL IMPULSOR

2MOTOR 11 AMORTIGUADORES DE VIBRACIÓN

3 ARRANQUE MANUAL 12 HOJA

4 TAPÓN DEL DEPÓSITO DE ACEITE 13 CUBIERTA DE LOS PESOS EXCÉNTRICOS

5 TAPÓN DEL DEPÓSITO DE GASOLINA 14 BASTIDOR

6PALANCA DEL ACELERADOR 15 PLACA UNIVERSAL DE MONTAJE

BLOQUES DE MONTAJE DE LA BARRA DE LAS MANIJAS

 CABLE DEL ACELERADOR

8 BARRA DE LAS MANIJAS 17 FILTRO DE AIRE

9BARRA DE APOYO

COMPONENTES COMUNES

11 13

5 de 14

WS#3747 104 S. 8th Ave. Marshalltown, IA Teléfono 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.com

INSTRUCCIONES DE MONTAJE

Paso 1 – Quite los cuatro tornillos hexagonales (A) que fijan los dos

bloques de montaje de la barra de las manijas.

Paso 2 – Deslice el brazo de la barra de apoyo en el extremo de la

barra de apoyo y fíjelo con el perno y la tuerca (B) como se muestra.

Paso 4 – Asegurándose de que todos los orificios de los bloques

de montaje y del bastidor estén alineados, inserte los tornillos

hexagonales y apriételos con una llave de tuercas o de cubo de 7/16

pulg.

Paso 3 – Coloque la barra de las manijas en los bloques de montaje,

asegurándose de que quede bien centrada en los mismos.

INSTALACIÓN DE LA BARRA DE LAS MANIJAS Y DE LA BARRA DE APOYO

INSTALACIÓN DE LA HOJA

Asegúrese de que los pernos estén bien apretados

antes de cada uso de la unidad

! !

Siga estos pasos para montar fácilmente la unidad:

Instale la hoja como se muestra, asegurándose de que la hoja quede

instalada en la parte posterior de la extrusión de la base con los

espaciadores de hoja (A) a ambos lados de la hoja.

6 de 14 WS#3747104 S. 8th Ave. Marshalltown, IA Teléfono 800-888-0127 / 641-753-0127 • Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.com

INSTALACIÓN DEL CABLE DEL ACELERADOR

Paso 1 – Quite la cubierta del carburador

presionando los

sujetadores.

Paso 3 – Sujete el cable del acelerador

como se muestra. Asegúrese de que haya

una tuerca a cada lado del conector plástico.

Asegúrese de que el cable no se salga del

conector plástico mientras lo aprieta.

Paso 2 – El acelerador tiene una espiga gira-

toria plateada con una ranura en una de sus

caras. Un extremo del cable del acelerador

tiene un cilindro de metal (B) que cabe en

esta ranura. Introduzca el cilindro en la ranura

de manera de que cuando se jale el cable

del acelerador se abra el acelerador (hacia la

placa base del vibrador).

PRECAUCIÓN

Siempre asegúrese de que el motor esté parado, con el interruptor en la posición “OFF” antes de hacer ajustes.

AJUSTES DE LA MÁQUINA

AJUSTABLE

MANIJAS

Su vibrador Speed Striker™ tiene manijas que puede ajustar para su

comodidad.

La altura de las manijas se puede ajustar inmediatamente debajo

del motor.

La page est en cours de chargement...

Marshalltown Speed Striker 2.0 Le manuel du propriétaire

Marque: Marshalltown

Modèle: Speed Striker 2.0

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

español: Marshalltown Speed Striker 2.0 El manual del propietario

Marshalltown Speed Striker 2.0 Le manuel du propriétaire

Marshalltown Speed Striker 2.0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents