Wacker Neuson CT24-4A Manuel utilisateur

Taper
Manuel utilisateur
Operator’s Manual
Trowel
CT 24A
Notice d’Emploi
Truelle mécanique
5000184501 07 0912
EN / FR
5000184501
Copyright
notice
© Copyright 2012 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the machine. Any
other type of reproduction is prohibited without express written permission from
Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker Neuson Production
Americas LLC represents an infringement of valid copyrights. Violators will be
prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original
instructions
This Operator’s Manual presents the original instructions. The original language of this
Operator’s Manual is American English.
5000184477 07 0912
CT 24-4A Foreword
wc_tx001519gb.fm 3
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
Use the separate Parts Book supplied with the machine to order replacement
parts.
If you are missing either of these documents, please contact Wacker Neuson to
order a replacement or visit www.wackerneuson.com.
When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change
any portion of this information without notice.
Manufacturer’s
approval
This manual contains references to approved parts, attachments, and modifica-
tions. The following definitions apply:
Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following conse-
quences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
Machine Item Number
CT 24-24A 0620105, 0620849
Foreword CT 24-4A
4 wc_tx001519gb.fm
CALIFORNIA
Proposition
65 Warning
Engine exhaust, some of its constituents, and certain vehicle components, contain
or emit chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-
charge of sparks or flames from the engine exhaust. Spark arresters are qualified
and rated by the United States Forest Service for this purpose. In order to comply
with local laws regarding spark arresters, consult the engine distributor or the local
Health and Safety Administrator.
Original Declaration of Conformity
2012-CE-CT24_en.fm
EC Declaration of Conformity
Manufacturer
Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,
Menomonee Falls, Wisconsin USA 53051
Product
Product
Product category
Product function
Item number
CT 24-4A, CT 24-230E
Trowel
To smooth and finish semi-cured concrete
0620848, 0620849
Directives and Standards
We hereby declare that this product meets and complies with the relevant regulations and
requirements of the following directives and standards:
2006/42/EC, 2006/95/EC, 2004/108/EC, EN12649
Authorized Person for Technical Documents
Axel Häret, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41,
80809 München
Menomonee Falls, WI, USA,
William Lahner
Managing Director
Robert Motl
Director of Business Development
Scott V. Grahl
Manager, Product Engineering
Table of Contents
CT 24-4A
wc_bo5000184477_07TOC.fm
7
Foreword 3
EC Declaration of Conformity 5
1 Safety Information 9
1.1 Signal Words found in this Manual ....................................................... 9
1.2 Machine Description and Intended Use ............................................. 10
1.3 Operating Safety ................................................................................ 12
1.4 Operator Safety while Using Internal Combustion Engines ............... 14
1.5 Service Safety .................................................................................... 15
2 Labels 18
2.1 Label Locations .................................................................................. 18
2.2 Label Meanings .................................................................................. 19
3 Lifting and Transporting 22
3.1 Lifting the Machine ............................................................................. 22
3.2 Transporting the Machine ................................................................... 23
4 Operation 24
4.1 Preparing for First Use ....................................................................... 24
4.2 New Machine Set-Up ......................................................................... 24
4.3 Recommended Fuel ........................................................................... 25
4.4 Refueling the Machine ........................................................................ 26
4.5 Installing Blades ................................................................................. 27
4.6 Unfolding Handle ................................................................................ 28
4.7 Controls .............................................................................................. 29
4.8 Operator Present Lever ...................................................................... 29
4.9 Before Starting ................................................................................... 30
4.10 To Start ............................................................................................... 30
4.11 To Stop ............................................................................................... 31
4.12 Position of the Operator ..................................................................... 32
4.13 Operation ............................................................................................ 32
4.14 Emegency Shutdown Procedure ........................................................ 33
4.15 Pitch Adjustment ................................................................................ 34
Table of Contents
CT 24-4A
wc_bo5000184477_07TOC.fm
8
5 Maintenance 35
5.1 Maintaining the Emission Control System ...........................................35
5.2 Periodic Maintenance Schedule ..........................................................35
5.3 Engine Oil ............................................................................................36
5.4 Air Cleaner ..........................................................................................37
5.5 Spark Plug ...........................................................................................38
5.6 Cleaning Sediment Cup ......................................................................39
5.7 Adjusting Idle Speed ...........................................................................40
5.8 Carburetor Adjustment ........................................................................41
5.9 Belt Replacement ................................................................................42
5.10 Trowel Lubrication ...............................................................................43
5.11 Storage ................................................................................................44
6 Troubleshooting 45
6.1 Basic Troubleshooting .........................................................................45
7 Technical Data 46
7.1 Dimensions and Weights .....................................................................46
7.2 Engine .................................................................................................47
7.3 Trowel ..................................................................................................48
7.4 Sound and Vibration Data ...................................................................49
8 Emission Control Systems Information and Warranty 50
8.1 Emission Control Systems Warranty Statement .................................50
9 AEM Safety Manual 51
CT24-4A Safety Information
wc_si000504gb.fm 9
1 Safety Information
1.1 Signal Words found in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and
NOTE signal words which must be followed to reduce the possibility
of personal injury, damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a
situation which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
f Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
f
To avoid death or serious injury from this type of hazard, obey all safety messages that
follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
f
To avoid possible death or serious injury from this type of hazard, obey all safety mes-
sages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
f
To avoid possible minor or moderate injury from this type of hazard, obey all safety mes-
sages that follow this signal word.
Safety Information CT24-4A
10 wc_si000504gb.fm
1.2 Machine Description and Intended Use
This machine is a walk-behind concrete finishing trowel. The Wacker
Neuson Walk-Behind Trowel consists of a frame onto which are
mounted a gasoline engine, a fuel tank, a gearbox, and a control
handle. A set of four metal blades is connected to the gearbox and is
surrounded by a ring guard. The engine rotates the blades through
the gearbox and clutch mechanism. The rotating blades ride on the
surface of curing concrete, creating a smooth finish. The operator
walks behind the machine and uses the handle to control speed and
direction of the machine.
This machine is intended to be used for floating and burnishing curing
concrete.
This machine has been designed and built strictly for the intended use
described above. Using the machine for any other purpose could
permanently damage the machine or seriously injure the operator or
other persons in the area. Machine damage caused by misuse is not
covered under warranty.
The following are some examples of misuse:
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Using the machine to finish inappropriate materials such as
slurries, sealers, or epoxy finishes
Operating the machine outside of factory specifications
Operating the machine in a manner inconsistent with all warnings
found on the machine and in the Operator’s Manual
This machine has been designed and built in accordance with the
latest global safety standards. It has been carefully engineered to
eliminate hazards as far as practicable and to increase operator
safety through protective guards and labeling. However, some risks
may remain even after protective measures have been taken. They
are called residual risks. On this machine, they may include exposure
to:
Heat, noise, exhaust, and carbon monoxide from the engine
Chemical burns from curing concrete
Fire hazards from improper refueling techniques
Fuel and its fumes, fuel spillage from improper lifting technique
Personal injury from improper lifting techniques or operating
techniques
Cutting hazards from sharp or worn blades
CT24-4A Safety Information
wc_si000504gb.fm 11
To protect yourself and others, make sure you thoroughly read and
understand the safety information presented in this manual before
operating the machine.
Safety Information CT24-4A
12 wc_si000504gb.fm
1.3 Operating Safety
Familiarity and proper training are required for the safe operation of the
machine. Machines operated improperly or by untrained personnel
can be hazardous. Read the operating instructions contained in this
manual and the engine manual, and familiarize yourself with the
location and proper use of all controls. Inexperienced operators should
receive instruction from someone familiar with the machine before
being allowed to operate it.
Operator qualifications
Only trained personnel are permitted to start, operate, and shut down
the machine. They also must meet the following qualifications:
have received instruction on how to properly use the machine
are familiar with required safety devices
The machine must not be accessed or operated by:
children
people impaired by alcohol or drugs
Operator training
Before operating the machine:
Read and understand the operating instructions contained in all
manuals delivered with the machine.
Familiarize yourself with the location and proper use of all
controls and safety devices.
Contact Wacker Neuson for additional training if necessary.
When operating this machine:
Do not allow improperly trained people to operate the machine.
People operating the machine must be familiar with the potential
risks and hazards associated with it.
Personal Protective Equipment (PPE)
Wear the following Personal Protective Equipment (PPE) while
operating this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
1.3.1 Do not allow anyone to operate this equipment without proper training.
People operating this equipment must be familiar with the risks and
hazards associated with it.
WARNING
CT24-4A Safety Information
wc_si000504gb.fm 13
1.3.2 Do not touch the engine or muffler while the engine is on or
immediately after it has been turned off. These areas get hot and may
cause burns.
1.3.3 Do not operate the machine with unapproved accessories or
attachments.
1.3.4 Do not leave the machine running unattended.
1.3.5 NEVER operate the machine with the beltguard missing. Exposed
drive belt and pulleys create potentially dangerous hazards that can
cause serious injuries.
1.3.6 Never operate this machine in applications for which it is not intended.
1.3.7 NEVER use the trowel around pop-ups in the concrete that are lower
than the lowest ring on the ring guard.
1.3.8 NEVER lift the machine solely by the handle. The component may fail,
causing the machine to fall, possibly injuring bystanders.
1.3.9 Always wear protective clothing appropriate to the job site when
operating the machine.
1.3.10 ALWAYS wear hearing and eye protection when operating this
machine.
1.3.11 ALWAYS remain aware of moving parts and keep hands, feet, and
loose clothing away from the moving parts of the machine.
1.3.12 Read, understand, and follow procedures in the Operator’s Manual
before attempting to operate the machine.
1.3.13 Store the machine properly when it is not being used. The machine
should be stored in a clean, dry location out of the reach of children.
1.3.14 Close fuel valve on engines equipped with one when machine is not
being operated.
1.3.15 Always operate machine with all safety devices and guards in place
and in working order. Do not modify or defeat safety devices. Do not
operate machine if any safety devices or guards are missing or
inoperative.
1.3.16 Be sure operator is familiar with proper safety precautions and
operation techniques before using machine.
1.3.17 ALWAYS test the function of the engine control module before
operating the trowel. DO NOT operate the trowel if the engine control
module is not functioning properly.
1.3.18 Do not use a cellphone or send text messages while operating this
machine.
1.3.19 Do not transport the machine while it is running.
1.3.20 Do not tip the machine for cleaning or for any other reason.
Safety Information CT24-4A
14 wc_si000504gb.fm
1.4 Operator Safety while Using Internal Combustion Engines
Operating safety
When running the engine:
Keep the area around exhaust pipe free of flammable materials.
Check the fuel lines and the fuel tank for leaks and cracks before
starting the engine. Do not run the machine if fuel leaks are
present or the fuel lines are loose.
When running the engine:
Do not smoke while operating the machine.
Do not run the engine near sparks or open flames.
Do not touch the engine or muffler while the engine is running or
immediately after it has been turned off.
Do not operate a machine when its fuel cap is loose or missing.
Do not start the engine if fuel has spilled or a fuel odor is present.
Move the machine away from the spill and wipe the machine dry
before starting.
Refueling safety
When refueling the engine:
Clean up any spilled fuel immediately.
Refill the fuel tank in a well-ventilated area.
Reinstall the fuel tank cap after refueling.
Do not smoke.
Do not refuel a hot or running engine.
Do not refuel the engine near sparks or open flames.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
f Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
Exhaust gas from the engine contains carbon monoxide, a deadly poison. Expo-
sure to carbon monoxide can kill you in minutes.
f NEVER operate the machine inside an enclosed area, such as a tunnel, unless
adequate ventilation is provided through such items as exhaust fans or hoses.
CT24-4A Safety Information
wc_si000504gb.fm 15
Use suitable tools for refueling (for example, a fuel hose or
funnel).
Do not refuel if the machine is positioned in a truck fitted with a
plastic bed liner. Static electricity can ignite the fuel or fuel vapors.
1.5 Service Safety
A poorly maintained machine can become a safety hazard! In order
for the machine to operate safely and properly over a long period of
time, periodic maintenance and occasional repairs are necessary.
Personal Protective Equipment (PPE)
Wear the following Personal Protective Equipment (PPE) while
servicing or maintaining this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
In addition, before servicing or maintaining the machine:
Tie back long hair.
Remove all jewelry (including rings).
Service training
Before servicing or maintaining the machine:
Read and understand the instructions contained in all manuals
delivered with the machine.
Familiarize yourself with the location and proper use of all
controls and safety devices.
Only trained personnel shall troubleshoot or repair problems
occurring with the machine.
Contact Wacker Neuson for additional training if necessary.
When servicing or maintaining this machine:
Do not allow improperly trained people to service or maintain the
machine. Personnel servicing or maintaining the machine must
be familiar with the associated potential risks and hazards.
1.5.1 Do not attempt to clean or service the machine while it is running.
Rotating parts can cause severe injury.
WARNING
Safety Information CT24-4A
16 wc_si000504gb.fm
1.5.2 Do not crank a flooded engine with the spark plug removed on
gasoline-powered engines. Fuel trapped in the cylinder will squirt out
the spark plug opening.
1.5.3 Do not test for spark on gasoline-powered engines if the engine is
flooded or the smell of gasoline is present. A stray spark could ignite
the fumes.
1.5.4 Do not use gasoline or other types of fuels or flammable solvents to
clean parts, especially in enclosed areas. Fumes from fuels and
solvents can become explosive.
1.5.5 DO NOT remove blades while the machine is hanging overhead.
1.5.6 ALWAYS support the machine securely before changing blades.
1.5.7 Keep the area around the muffler free of debris such as leaves, paper,
cartons, etc. A hot muffler could ignite the debris and start a fire.
1.5.8 When replacement parts are required for this machine, use only
Wacker Neuson replacement parts or those parts equivalent to the
original in all types of specifications, such as physical dimensions,
type, strength, and material.
1.5.9 Disconnect the spark plug on machines equipped with gasoline
engines, before servicing, to avoid accidental start-up.
1.5.10 Keep the machine clean and labels legible. Replace all missing and
hard-to-read labels. Labels provide important operating instructions
and warn of dangers and hazards.
1.5.11 ALWAYS handle blades carefully. The blades can develop sharp
edges which can cause serious cuts.
CT24-4A Safety Information
wc_si000504gb.fm 17
Notes
Labels CT24-4A
18 wc_si000505gb.fm
2Labels
2.1 Label Locations
CT24-4A Labels
wc_si000505gb.fm 19
2.2 Label Meanings
A
DANGER!
Asphyxiation hazard.
Engines emit carbon monoxide.
Do not run the machine indoors or in an enclosed
area unless adequate ventilation, through such items
as exhaust fans or hoses, is provided.
Read the Operator’s Manual. No sparks, flames, or
burning objects near the machine. Stop the engine
before refueling.
B
WARNING!
Hot surface
C
WARNING!
Hand injury if caught in moving belt.
Always replace beltguard.
D
WARNING!
Always wear hearing and eye protection when operating
this machine.
Labels CT24-4A
20 wc_si000505gb.fm
E
WARNING!
Cutting hazard. Always replace blade guard!
F
Variable speed throttle
G
CAUTION!
Read and understand the supplied Operator’s Manual
before operating this machine. Failure to do so
increases the risk of injury to yourself and others.
H
NOTICE
Lifting point.
A nameplate listing the model number, item number,
revision number, and serial number is attached to each
unit. Please record the information found on this name-
plate so it will be available should the nameplate
become lost or damaged. When ordering parts or
requesting service information, you will always be asked
to specify the model number, item number, revision
number, and serial number of the unit.
178709
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120

Wacker Neuson CT24-4A Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues