Wacker Neuson CT24-4A Manuel utilisateur

Operator’s Manual

Trowel

CT 24A

Notice d’Emploi

Truelle mécanique

5000184501 06 0611

EN / FR

5000184501

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000184477 06 0611

CT 24-4A Foreword

wc_tx001519gb.fm 3

Foreword

Machines

covered in

this manual

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 If you are missing either of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Machine Item Number

CT 24-24A 0620105, 0620849

Foreword CT 24-4A

4 wc_tx001519gb.fm

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Original Declaration of Conformity

2011-CE-CT24_en.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin USA

Product

Product category

Product function

Item number

CT 24-4A, CT 24-230E

Trowel

To smooth and finish semi-cured concrete

0620848, 0620849

Guidelines and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following guidelines and standards:

2006/42/EC, 2006/95/EC, 2004/108/EC, EN12649

Authorized Person for Technical Documents

Axel Häret, Wacker Neuson SE, Preußenstraße 41, 80809 München

Menomonee Falls, WI, USA, 24.06.11

William Lahner Scott V. Grahl

Table of Contents

CT 24-4A

wc_bo5000184477_06TOC.fm

7

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 9

1.1 Signal Words found in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Operating Safety ................................................................................ 11

1.4 Operator Safety while Using Internal Combustion Engines ............... 13

1.5 Service Safety .................................................................................... 14

2 Labels 16

2.1 Label Locations .................................................................................. 16

2.2 Label Meanings .................................................................................. 17

3 Lifting and Transporting 20

3.1 Lifting the Machine ............................................................................. 20

3.2 Transporting the Machine ................................................................... 21

4 Operation 23

4.1 Preparing for First Use ....................................................................... 23

4.2 New Machine Set-Up ......................................................................... 23

4.3 Recommended Fuel ........................................................................... 24

4.4 Refueling the Machine ........................................................................ 25

4.5 Installing Blades ................................................................................. 26

4.6 Unfolding Handle ................................................................................ 27

4.7 Controls .............................................................................................. 28

4.8 Operator Present Lever ...................................................................... 29

4.9 Before Starting ................................................................................... 29

4.10 To Start ............................................................................................... 30

4.11 To Stop ............................................................................................... 31

4.12 Position of the Operator ..................................................................... 32

4.13 Operation ............................................................................................ 32

4.14 Emegency Shutdown Procedure ........................................................ 33

4.15 Pitch Adjustment ................................................................................ 34

Table of Contents

CT 24-4A

wc_bo5000184477_06TOC.fm

8

5 Maintenance 35

5.1 Maintaining the Emission Control System ...........................................35

5.2 Periodic Maintenance Schedule ..........................................................35

5.3 Engine Oil ............................................................................................36

5.4 Air Cleaner ..........................................................................................37

5.5 Spark Plug ...........................................................................................38

5.6 Cleaning Sediment Cup ......................................................................39

5.7 Adjusting Idle Speed ...........................................................................40

5.8 Carburetor Adjustment ........................................................................41

5.9 Belt Replacement ................................................................................42

5.10 Trowel Lubrication ...............................................................................43

5.11 Storage ................................................................................................44

6 Troubleshooting 45

6.1 Basic Troubleshooting .........................................................................45

7 Technical Data 46

7.1 Dimensions and Weight ......................................................................46

7.2 Engine .................................................................................................47

7.3 Trowel ..................................................................................................48

7.4 Sound and Vibration Data ...................................................................49

8 Emission Control Systems Information and Warranty 50

8.1 Emission Control Systems Warranty Statement .................................50

9 AEM Safety Manual 51

CT24-4A Safety Information

wc_si000504gb.fm 9

1 Safety Information

1.1 Signal Words found in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f

To avoid death or serious injury from this type of hazard, obey all safety messages that

follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f

To avoid possible death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f

To avoid possible minor or moderate injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

Safety Information CT24-4A

10 wc_si000504gb.fm

1.2 Machine Description and Intended Use

This machine is a walk-behind concrete finishing trowel. The Wacker

Neuson Walk-Behind Trowel consists of a frame onto which are

mounted a gasoline engine, a fuel tank, a gearbox, and a control

handle. A set of four metal blades is connected to the gearbox and is

surrounded by a ring guard. The engine rotates the blades through

the gearbox and clutch mechanism. The rotating blades ride on the

surface of curing concrete, creating a smooth finish. The operator

walks behind the machine and uses the handle to control speed and

direction of the machine.

This machine is intended to be used for floating and burnishing curing

concrete.

This machine has been designed and built strictly for the intended use

described above. Using the machine for any other purpose could

permanently damage the machine or seriously injure the operator or

other persons in the area. Machine damage caused by misuse is not

covered under warranty.

The following are some examples of misuse:

• Using the machine as a ladder, support, or work surface

• Using the machine to carry or transport passengers or equipment

• Using the machine to finish inappropriate materials such as

slurries, sealers, or epoxy finishes

• Operating the machine outside of factory specifications

• Operating the machine in a manner inconsistent with all warnings

found on the machine and in the Operator’s Manual

This machine has been designed and built in accordance with the

latest global safety standards. It has been carefully engineered to

eliminate hazards as far as practicable and to increase operator

safety through protective guards and labeling. However, some risks

may remain even after protective measures have been taken. They

are called residual risks. On this machine, they may include exposure

to:

• Heat, noise, exhaust, and carbon monoxide from the engine

• Chemical burns from curing concrete

• Fire hazards from improper refueling techniques

• Fuel and its fumes, fuel spillage from improper lifting technique

• Personal injury from improper lifting techniques or operating

techniques

• Cutting hazards from sharp or worn blades

CT24-4A Safety Information

wc_si000504gb.fm 11

To protect yourself and others, make sure you thoroughly read and

understand the safety information presented in this manual before

operating the machine.

1.3 Operating Safety

Familiarity and proper training are required for the safe operation of the

machine. Machines operated improperly or by untrained personnel

can be hazardous. Read the operating instructions contained in this

manual and the engine manual, and familiarize yourself with the

location and proper use of all controls. Inexperienced operators should

receive instruction from someone familiar with the machine before

being allowed to operate it.

Operator qualifications

Only trained personnel are permitted to start, operate, and shut down

the machine. They also must meet the following qualifications:

• have received instruction on how to properly use the machine

• are familiar with required safety devices

The machine must not be accessed or operated by:

•children

• people impaired by alcohol or drugs

Operator training

Before operating the machine:

• Read and understand the operating instructions contained in all

manuals delivered with the machine.

• Familiarize yourself with the location and proper use of all

controls and safety devices.

• Contact Wacker Neuson for additional training if necessary.

When operating this machine:

• Do not allow improperly trained people to operate the machine.

People operating the machine must be familiar with the potential

risks and hazards associated with it.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

operating this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

WARNING

Safety Information CT24-4A

12 wc_si000504gb.fm

1.3.1 Do not allow anyone to operate this equipment without proper training.

People operating this equipment must be familiar with the risks and

hazards associated with it.

1.3.2 Do not touch the engine or muffler while the engine is on or

immediately after it has been turned off. These areas get hot and may

cause burns.

1.3.3 Do not operate the machine with unapproved accessories or

attachments.

1.3.4 Never leave the machine running unattended.

1.3.5 NEVER operate the machine with the beltguard missing. Exposed

drive belt and pulleys create potentially dangerous hazards that can

cause serious injuries.

1.3.6 Never operate this machine in applications for which it is not intended.

1.3.7 NEVER use the trowel around pop-ups in the concrete that are lower

than the lowest ring on the ring guard.

1.3.8 NEVER lift the machine solely by the handle. The component may fail,

causing the machine to fall, possibly injuring bystanders.

1.3.9 Always wear protective clothing appropriate to the job site when

operating the machine.

1.3.10 ALWAYS wear hearing and eye protection when operating this

machine.

1.3.11 ALWAYS remain aware of moving parts and keep hands, feet, and

loose clothing away from the moving parts of the machine.

1.3.12 Read, understand, and follow procedures in the Operator’s Manual

before attempting to operate the machine.

1.3.13 Store the machine properly when it is not being used. The machine

should be stored in a clean, dry location out of the reach of children.

1.3.14 Close fuel valve on engines equipped with one when machine is not

being operated.

1.3.15 Always operate machine with all safety devices and guards in place

and in working order. Do not modify or defeat safety devices. Do not

operate machine if any safety devices or guards are missing or

inoperative.

1.3.16 Be sure operator is familiar with proper safety precautions and

operation techniques before using machine.

1.3.17 ALWAYS test the function of the engine control module before

operating the trowel. DO NOT operate the trowel if the engine control

module is not functioning properly.

1.3.18 Do not use a cellphone or send text messages while operating this

machine.

1.3.19 Do not transport the machine while it is running.

CT24-4A Safety Information

wc_si000504gb.fm 13

1.3.20 Do not tip the machine for cleaning or for any other reason.

1.4 Operator Safety while Using Internal Combustion Engines

Operating safety

When running the engine:

• Keep the area around exhaust pipe free of flammable materials.

• Check the fuel lines and the fuel tank for leaks and cracks before

starting the engine. Do not run the machine if fuel leaks are present

or the fuel lines are loose.

When running the engine:

• Do not smoke while operating the machine.

• Do not run the engine near sparks or open flames.

• Do not touch the engine or muffler while the engine is running or

immediately after it has been turned off.

• Do not operate a machine when its fuel cap is loose or missing.

• Do not start the engine if fuel has spilled or a fuel odor is present.

Move the machine away from the spill and wipe the machine dry

before starting.

Refueling safety

When refueling the engine:

• Clean up any spilled fuel immediately.

• Refill the fuel tank in a well-ventilated area.

• Replace the fuel tank cap after refueling.

• Do not smoke.

• Do not refuel a hot or running engine.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison. Expo-

sure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

Safety Information CT24-4A

14 wc_si000504gb.fm

• Do not refuel the engine near sparks or open flames.

• Do not refuel if the machine is positioned in a truck fitted with a

plastic bed liner. Static electricity can ignite the fuel or fuel vapors.

1.5 Service Safety

A poorly maintained machine can become a safety hazard! In order

for the machine to operate safely and properly over a long period of

time, periodic maintenance and occasional repairs are necessary.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

servicing or maintaining this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

In addition, before servicing or maintaining the machine:

• Tie back long hair.

• Remove all jewelry (including rings).

Service training

Before servicing or maintaining the machine:

• Read and understand the instructions contained in all manuals

delivered with the machine.

• Familiarize yourself with the location and proper use of all

controls and safety devices.

• Only trained personnel shall troubleshoot or repair problems

occurring with the machine.

• Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

• Do not allow improperly trained people to service or maintain the

machine. Personnel servicing or maintaining the machine must

be familiar with the associated potential risks and hazards.

1.5.1 Do not attempt to clean or service the machine while it is running.

Rotating parts can cause severe injury.

1.5.2 Do not crank a flooded engine with the spark plug removed on

gasoline-powered engines. Fuel trapped in the cylinder will squirt out

the spark plug opening.

WARNING

CT24-4A Safety Information

wc_si000504gb.fm 15

1.5.3 Do not test for spark on gasoline-powered engines if the engine is

flooded or the smell of gasoline is present. A stray spark could ignite

the fumes.

1.5.4 Do not use gasoline or other types of fuels or flammable solvents to

clean parts, especially in enclosed areas. Fumes from fuels and

solvents can become explosive.

1.5.5 DO NOT remove blades while the machine is hanging overhead.

1.5.6 ALWAYS support the machine securely before changing blades.

1.5.7 Keep the area around the muffler free of debris such as leaves, paper,

cartons, etc. A hot muffler could ignite the debris and start a fire.

1.5.8 When replacement parts are required for this machine, use only

Wacker Neuson replacement parts or those parts equivalent to the

original in all types of specifications, such as physical dimensions,

type, strength, and material.

1.5.9 Disconnect the spark plug on machines equipped with gasoline

engines, before servicing, to avoid accidental start-up.

1.5.10 Keep the machine clean and labels legible. Replace all missing and

hard-to-read labels. Labels provide important operating instructions

and warn of dangers and hazards.

1.5.11 ALWAYS handle blades carefully. The blades can develop sharp

edges which can cause serious cuts.

Labels CT24-4A

16 wc_si000505gb.fm

2Labels

2.1 Label Locations

CT24-4A Labels

wc_si000505gb.fm 17

2.2 Label Meanings

Label Meaning

A

DANGER!

Asphyxiation hazard.

 Engines emit carbon monoxide.

 Do not run the machine indoors or in an enclosed

area unless adequate ventilation, through such items

as exhaust fans or hoses, is provided.

 Read the Operator’s Manual. No sparks, flames, or

burning objects near the machine. Stop the engine

before refueling.

B

WARNING!

Hot surface

C

WARNING!

Hand injury if caught in moving belt.

Always replace beltguard.

D

WARNING!

Always wear hearing and eye protection when operating

this machine.

Labels CT24-4A

18 wc_si000505gb.fm

E

WARNING!

Cutting hazard. Always replace blade guard!

F

Variable speed throttle

G

CAUTION!

Read and understand the supplied Operator’s Manual

before operating this machine. Failure to do so

increases the risk of injury to yourself and others.

H

NOTICE

Lifting point.

A nameplate listing the model number, item number,

revision number, and serial number is attached to each

unit. Please record the information found on this name-

plate so it will be available should the nameplate

become lost or damaged. When ordering parts or

requesting service information, you will always be asked

to specify the model number, item number, revision

number, and serial number of the unit.

Label Meaning

CT24-4A Labels

wc_si000505gb.fm 19

This machine may be covered by one or more patents.

J

To start the machine:

1. Open the fuel flow valve.

2. Close the choke.

3. Push or turn engine switch to ON position.

4. Place throttle in the IDLE position.

5. Engage operator present lever.

6. Pull the rewind starter.

7. Open the choke.

To stop the machine:

1. Release operator present lever.

2. Push or turn engine switch to OFF position.

3. Close the fuel flow valve.

Label Meaning

3

2

1

7

6

5

4

3

2

1

172847

Lifting and Transporting CT 24-230E

20 wc_tx001520gb.fm

3 Lifting and Transporting

3.1 Lifting the Machine

See Graphic: wc_gr004390

NEVER lift the machine solely by the handle. The component may fail,

causing the machine to fall, possibly injuring bystanders.

See Technical Data for the weight of the machine.

To lift the machine manually:

3.1.1 Stop machine.

3.1.2 Obtain a partner and plan the lift.

3.1.3 Balance the weight between the partners and lift the machine by the

guard ring (a).

To reduce risk of back injury while lifting, keep your feet flat on ground

and shoulder width apart. Keep your head up and back straight.

To lift the machine mechanically:

3.1.4 Stop machine.

3.1.5 See Dimensions and Weight for weight of machine and be sure that

lifting device(s) can safely lift the weight.

3.1.6 Attach hook, harness, or cable to the lifting bracket (b) on machine as

shown and lift as desired.

Do not lift the trowel overhead with a float pan attached, as the pan

could fall off and strike personnel working in the vicinity.

WARNING

a

c

wc_gr004390

b

La page charge ...

Wacker Neuson CT24-4A Manuel utilisateur

Wacker Neuson CT24-4A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents