Thermador WD30WC Guide d'installation

Installation

GUIDE

THERMADOR.COM

Masterpiece® and Professional Series

Warming Drawer and Storage Drawer

WD30WC WD30W SD30WC SDS30WC

Table of

CONTENTS

Table of Contents

Installation Instructions

9 Safety Definitions .................................................. 3

IMPORTANT SAFETY INSTRUCTIONS ........................ 4

Appliance Handling Safety ............................................. 4

Safety Codes and Standards ........................................... 4

Electric Safety ................................................................. 4

Related Equipment Safety .............................................. 5

State of California Proposition 65 Warnings: .................. 5

Before you Begin ........................................................ 6

Tools and Parts Needed .................................................. 6

Parts Included ................................................................. 6

Power Requirements and Grounding ............................. 6

Prepare Installation Space .......................................... 6

Cabinet and Cutout Information ..................................... 6

Unit Dimensions SDS30WC ............................................ 6

Unit and Cabinet Dimensions WD30W / WD30WC /

SD30WC .......................................................................... 6

Installation Procedure WD30WC, SD30WC ................ 7

Removing Drawer from Housing .................................... 8

Installing Drawer to Housing .......................................... 8

Parts Included ............................................................... 10

Installing with Microwave .............................................. 10

Installation Procedure SDS30WC .............................. 12

Removing Drawer from Housing .................................. 13

Preparing the Storage Drawer for Installation .............. 13

Remove Shipping Brackets ........................................... 14

Install Steam Oven on Top of Storage Drawer ............. 15

Installing Drawer to Housing ........................................ 15

Installation Procedure WD30W ................................ 17

Preparing the Custom Panel for Installation ................. 17

Attaching the Custom Panel ......................................... 18

Installation Final Check List ........................................... 19

Service ...................................................................... 20

Data Plate ..................................................................... 20

Rating Label-WD30W AND WD30WC ......................... 20

Model Number and FD Number .................................. 20

THERMADOR® Support ........................................... 21

Service ........................................................................... 21

Parts and Accessories ................................................... 21

.

3

9 Safety Definitions

Safety Defi nitions

9 WARNING

This indicates that death or serious injuries may

occur as a result of non-observance of this warning.

9 CAUTION

This indicates that minor or moderate injuries may

occur as a result of non-observance of this warning.

NOTICE: This indicates that damage to the appliance or

property may occur as a result of non-compliance with

this advisory.

Note: This alerts you to important information and/or

tips.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

4

IMPORTANT SAFET Y I NS T RUCT I ONS REA D AND SAVE THESE INSTRUCTIONS

IMPORTANT: SAVE THESE INSTRUCTIONS FOR THE

LOCAL ELECTRICAL INSPECTOR’S USE.

INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE

UNIT FOR THE OWNER.

OWNER: PLEASE RETAIN THESE INSTRUCTIONS FOR

FUTURE REFERENCE.

WARNING

When properly cared for, your new appliance has been

designed to be safe and reliable. Read all instructions

carefully before use. These precautions will reduce the

risk of burns, electric shock, fire and injury to persons.

When using kitchen appliances, basic safety precautions

must be followed including those in the following pages.

WARNING

Do not repair, replace or remove any part of the

appliance unless specifically recommended in the

manuals. Improper installation, service or maintenance

can cause injury or property damage. Refer to this

manual for guidance. All other servicing should be done

by an authorized servicer.

Appliance Handling Safety

Hidden surfaces may have sharp edges. Use caution

when reaching behind or under appliance.

Close supervision is necessary when any appliance is

used by or near children.

Do not touch hot surfaces. Use handles or knobs.

The use of accessory attachments not recommended by

the appliance manufacturer may cause injuries.

Do not use outdoors.

Do not place on or near a hot gas or electric burner or in

a heated oven.

Do not use appliance for other than intended use.

Extreme caution must be used when moving an

appliance containing hot oil or other hot liquids.

To reduce the risk of fire, do not locate any heating or

cooking appliance beneath the appliance.

To reduce the risk of fire, do not mount unit over or near

any portion of a heating or cooking appliance.

To reduce the risk of electric shock, do not mount over a

sink.

To reduce the risk of fire, do not store anything directly

on top of the appliance surface when the appliance is in

operation.

To reduce the risk of fire, do not store anything in the

warming drawer (such as groceries, bags, etc.) which

could cause fire if the drawer is turned on.

Safety Codes and Standards

This appliance complies with the latest version of one or

more of the following standards:

▯ UL 1026 - Electric Household Cooking and Food

Serving Appliances

▯ CSA-C22.2 No. 64 - Household Cooking and Liquid-

Heating Appliances

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

Electric Safety

WARNING

Before you plug in an electrical cord or turn on power

supply, make sure all controls are in the OFF position.

Do not let cord hang over edge of table or counter or

touch hot surfaces.

Always attach plug to appliance first, then plug cord into

wall outlet. To disconnect, turn any control to “off”, then

remove plug from wall outlet.

Do not operate any appliance with a damaged cord or

plug or after the appliance malfunctions or has been

damaged in any manner. It is unsafe to operate any

appliance with a damaged power cord or plug. If the

appliance has been damaged or malfunctions, safely

disconnect the appliance from the power supply, then

immediately contact a qualified appliance technician to

inspect the product.

To protect against electrical shock, do not immerse cord,

plugs or other electrical parts in water or other liquid.

For appliances equipped with a cord and plug, do not

cut or remove the ground prong. It must be plugged in to

a matching grounding type receptacle to avoid electrical

shock. If there is any doubt as to whether the wall

receptacle is properly grounded, the customer should

have it checked by a qualified electrician. DO NOT use

an adaptor or extension cord.

5

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

If required by the National Electrical Code (or Canadian

Electrical Code), this appliance must be installed on a

separate branch circuit.

Installer-show the owner the location of the circuit

breaker or fuse. Mark it for easy reference.

WARNING

Before installing, turn power OFF at the service panel.

Lock service panel to prevent power from being turned

ON accidentally.

Refer to data plate for more information. See “Data Plate”

under Service for data plate location.

Be sure your appliance is properly installed and

grounded by a qualified technician. Installation, electrical

connections and grounding must comply with all

applicable codes.

Related Equipment Safety

Remove all tape and packaging before using the

appliance. Discard or recycle packaging materials

according to local codes after unpacking the appliance.

Never modify or alter the construction of the appliance.

For example, do not remove panels or covers.

CAUTION

For units with glass panels, use care when handling

glass to avoid breaking. Broken glass could cause a

laceration type injury.

CAUTION

It is recommended to have two (2) installers to install the

unit assembly. Failure to do so may result in property

damage or personal injury.

IMPORTANT SAFETY NOTICE: The California Safe

Drinking and Toxic Enforcement Act requires the

Governor of California to publish a list of substances

known to the state to cause cancer, birth defects or other

reproductive harm, and requires businesses to warn

customers of potential exposure to such substances.

Save these instructions.

Proposition 65 Warning:

This product may contain a chemical known to the State

of California, which can cause cancer or reproductive

harm. Therefore, the packaging of your product may

bear the following label as required by California:



&DQFHUDQG5HSURGXFWLYH+DUPZZZ3:DUQLQJVFDJRY

67$7(2)&$/,)251,$352326,7,21:$51,1*

:$51,1*

6

Before you Begin

Tools and Parts Needed

▯ T-20 star head screwdriver

▯ Measuring tape

▯ Drill with bit (1/8”)

Parts Included

T-20 star head screws, #8 x 1/2” (6)

Power Requirements and Grounding

Circuit Specifications: 120V, 15A, 60Hz

The outlet must be properly grounded in accordance with

all applicable codes.

It is the responsibility of the installer to comply with local

codes. If no local codes are applicable, wire in

accordance with the National Electric Code, ANSI/NFPA

70-latest edition.

Prepare Installation Space

Cabinet and Cutout Information

Instructions are based on standard (in the U.S.A.)

cabinets 36” (914 mm) high and 24” (609 mm) deep

with a 25” (635 mm) countertop. If using non-standard

cabinets, alter dimensions accordingly.

Unit Dimensions SDS30WC

Maximum weight capacity for the storage drawer is 40

pounds (18 kg).

Note: The dimensional drawing is for reference only.

Refer to the installation guide included in the steam oven

for unit and cabinet dimensions.

Unit and Cabinet Dimensions WD30W /

WD30WC / SD30WC

Note: Power cord for the warming drawer units is 84”

(2134mm) long.

Cabinet opening bottom must be able to support

110 pounds (50 kg).

Flush Installation































PP

 PP

PP

PP

PP

PP

ò

ò

PP

ô

PP



0HDVXUHPHQWVLQLQFKHVPP

















  







 







  







 







  







  







  







  







  







  







7

Wall Mounted Installation

Thermador® warming drawers may be installed below

any Thermador® single or double built-in oven. A

minimum space of 1” (25.4mm) is recommended

between the bottom of the oven and the top of the

warming drawer.

Under Counter Installation

Thermador® warming drawers may also be installed

below any Thermador® electric or non-Professional

Series gas cooktop as long as there is not contact

between the bottom of the cooktop and the top of the

warming drawer. When installing below a Thermador®

induction cooktop, a minimum 1” (25.4mm) air gap must

be maintained between the bottom of the cooktop and

the top of the warming drawer.

When installing below a Thermador Professional®

rangetop, a minimum 2

3

/

4

” (70mm) air gap must be

maintained between the bottom of the rangetop and the

top of the warming drawer.

Installation Procedure WD30WC, SD30WC

The electrical outlet can be installed in the back wall

directly behind the warming drawer. A recessed power

receptacle must not exceed 5

1

/

2

ft. (1.7m) maximum

distance from either side of the warming drawer cutout.

Installation clearances permit for the excess power cord

to be coiled behind the appliance.

DO NOT install this warming drawer in wet locations or

outdoors.

9 WARNING

Do not repair, replace or remove any part of the

appliance unless specifically recommended in the

manuals. Improper installation, service or

maintenance can cause injury or property damage.

Refer to this manual for guidance. All other servicing

should be done by an authorized servicer.

NOTICE: This unit utilizes a special ball bearing slide

and locking feature called “Push to Open” (PTO). This

feature allows for a design without a handle and a flush

installation option.

There are two PTO slide assemblies installed in this unit,

one on each side. A slide is mounted to each side of the

housing and corresponding rails are mounted to each

side of the drawer. (Only one side is shown in picture for

clarity).

During installation or service (cleaning) it may be desired

or recommended to remove the drawer from the unit to

simplify or aid in installation or service. Special care and

specific steps are recommended to ensure no damage is

done to the PTO mechanism.

9 CAUTION

Before installing, turn power OFF at the service

panel. Lock service panel to prevent power from

being turned ON accidentally.

5DLO

6OLGH

8

Removing Drawer from Housing

NOTICE: The following is the manufacturer’s

recommendations for removing and installing the drawer

to minimize the risk of damage to the PTO mechanism.

1.

Remove the drawer from the drawer housing.

▯ Ensure drawer is at full open position.

▯ Press down right drawer release lever.

▯ Lift up left drawer release lever.

▯ Firmly pull the drawer straight out.

▯ Retract cabinet rails while drawer is removed.

2.

Grasp both sides of the drawer and pulling straight

and level, carefully remove the drawer housing. This

step may require light to moderate force to completely

remove drawer.

3.

Install or service (clean) housing with drawer removed.

Installing Drawer to Housing

The slides mounted to each side of the housing wall

have two moving components, an inner rail and a ball

bearing carrier which need to be in the proper orientation

for accurate installation and alignment.

There is also a visible locking mechanism located at the

rear of each slide.

Note: The housing of your warming drawer should

match the image below identically before starting your

installation. The ball bearing carrier should be locked in

to the inner rail’s black plastic rail tip at the front of the

inner rail.

-

0

8

)*()

@

.&%

13

00

'



0

/

0

''

6OLGH,QQHU5DLO

%DOO%HDULQJ&DUULHU

/RFNLQJ0HFKDQLVP

%DOO%HDULQJ&DUULHU

6OLGH,QQHU5DLO

9

1.

With the drawer removed, set the slide inner rail to the

drawer locked position by pushing the slide inner rail

toward the rear of the housing until it locks in place.

Note: A moderate force pushing on the black plastic

ball carrier locking mechanism is required to set the

slide to the drawer locked position. The drawer is

locked when it remains in place and does not spring

back to the open position.

2.

Position the drawer assembly in front of the housing

assembly and align the rail (plastic rail tip) to the slide

ball carrier assembly. Keeping the drawer assembly

level and square to the housing, gently insert the

drawer to the housing assembly.

Notes

▯ A slight side-to-side wiggle motion may be required

to properly get the ball bearings to accurately align.

▯ Remember: You are attempting to align two sets of

ball bearings at this point. If more than a moderate

force is required to insert the drawer at this time,

remove the drawer and repeat the installation

procedure to this point.

3.

Continue to insert the drawer keeping the drawer level

and square to the housing until a slight increase in

resistance is felt at the approximate position shown

below.

NOTICES

▯ At this position, a slight increase in closure force is

required with several small increments of force

applied to the drawer to accurately align and set the

drawer for proper operation.

▯ An audible “click” should be heard when the drawer

is properly closed causing the drawer to lock in the

closed position.

4MJEF*OOFS3BJM

-PDLJOH.FDIBOJTN

4MJEF*OOFS3BJMJTJOMPDLFEQPTJUJPO

10

4.

Test the operation of the PTO drawer by pushing on

the center lower portion of the drawer front (optimum

location for function).

Note: It should be noted the recommended and

optimum location for opening the drawer is the lower

center front. The drawer will operate with an opening

force applied to any location on the drawer front,

however a slight increase in opening force may be

required.

Parts Included

Note: The parts contained in the square tube parts box

are for microwave installations.

Installing with Microwave

1.

Position the warming drawer housing in front of the

cabinet where it is to be installed.

2.

Position the microwave or steam oven nearby.

3.

The warming drawer is ready for the microwave to be

mounted.

Pre-Assembly Preparation

Mounting the microwave on the warming drawer requires

the units to be assembled together prior to installing into

the cabinet cutout.

The 30” warming drawer is combinable with 30” built in

microwave/speed ovens. It is not combinable with the

trim kit microwaves or 27” microwaves.

Parts Provided

Mounting the Microwave on the Warming Drawer

Note: Do not place the warming drawer into the wall

cabinet until after mounting the microwave on it using the

universal connector brackets.

Note: The universal connector brackets are

interchangeable for the left and right sides of the

warming drawer. Be sure the taller vertical edge of the

bracket is positioned to the outside of the warming

drawer.

Assemble the Brackets to the Warming Drawer

1.

Attach both universal connector brackets to the

warming drawer housing using three of the screws

provided for each bracket (A). Tighten screws

securely, but do not over tighten.

Note: The existing screws in the microwave base help

with alignment. When lowering the microwave into

place on the universal connector bracket allow these

screw heads to slide into the slots as shown in the

illustration below. The screw nearest the front of the

microwave slides into the base of the slope at the font

of the bracket.

Universal connector

bracket (2) (in parts box).

Screws (16) (in red bag,

inside parts box).

2SWLPXPORFDWLRQIRU372IXQFWLRQ

-

08

)

*

(

)

@

.

&%

1

3

0

'



0

/



0

'

$

11

Place the microwave oven unit on top of the universal

connector brackets and fasten in place using three

screws per side in the outside set of holes. Tighten the

screws securely, but do not over tighten.

2.

Continue with the unit installation in the section below

describing installation of the warming drawer

microwave/steam oven unit into the wall cabinet.

Installation into the Cabinet Cutout

1.

Install the warming drawer and microwave assembly

into the cabinet cutout.

9 CAUTION

It is recommended to have 2 installers to install

the unit assembly. Failure to do so may result in

property damage or personal injury.

▯ Slide the assembly into the cabinet cutout until it is

flush with the front of the cabinet.

▯ Secure through screw holes in cleats (drill pilot

holes in cleats first if necessary). See installation

dimensions diagram. Secure microwave according

to installation instructions provided with those units.

2.

Replace drawer.

▯ Be sure cabinet rails are pushed inside cabinet.

▯ Align the rails on the drawer rails with the rails

attached to the drawer housing.

▯ Firmly push the drawer straight into the drawer

housing until the drawer clicks into place. The

drawer should insert easily. If it binds, do not

attempt to force it. Remove the drawer, align the

slides on the housing to the front edge of the

housing and try again. Slide the drawer into both

housing slides at the same time, and keep the

drawer level while doing so.

▯ The drawer has a “push-to-open” operation.

Pressing the front of the drawer inward causes the

drawer to self open.

▯ Open and close drawer to test operation.

Note: If the drawer will not close, verify that the rails

release levers are properly positioned.

3.

Turn power on at the service panel.

4.

Test the installation.

▯ Turn the warming drawer on. Signal light and timer

should turn on immediately.

▯ Check for warmth.

12

Installation Procedure SDS30WC

The SDS30WC storage drawer is specifically designed to

only be used with the single steam ovens MEDS301WS

and PODS301W.

Notes

▯ The cutout dimensions in this manual for the

SDS30WC are for reference only. For complete unit

and cabinet dimensions refer to the installation guide

included with the steam oven.

▯ The storage drawer combined with the steam oven

allows for the replacement of a standard single wall

oven.

▯ The steam oven is shorter than a standard wall oven.

The storage drawer when combined with the steam

oven allows for a direct replacement of a standard wall

oven.

▯ The drawer is functional storage drawer for the trays

and racks supplied with the steam oven.

9 WARNING

Do not repair, replace or remove any part of the

appliance unless specifically recommended in the

manuals. Improper installation, service or

maintenance can cause injury or property damage.

Refer to this manual for guidance. All other servicing

should be done by an authorized servicer.

NOTICE: This unit utilizes a special ball bearing slide

and locking feature called “Push to Open” (PTO). This

feature allows for a design without a handle and a flush

installation option.

There are two PTO slide assemblies installed in this unit,

one on each side. A slide is mounted to each side of the

housing and corresponding rails are mounted to each

side of the drawer. (Only one side is shown in picture for

clarity).

During installation or service (cleaning) it may be desired

or recommended to remove the drawer from the unit to

simplify or aid in installation or service. Special care and

specific steps are recommended to ensure no damage is

done to the PTO mechanism.

A Slide

B Rail

%

$

13

Removing Drawer from Housing

9 CAUTION

Hidden surfaces may have sharp edges. Use

caution when reaching into, around or under

appliance

NOTICE: The following is the manufacturer’s

recommendations for removing and installing the drawer

to minimize the risk of damage to the PTO mechanism.

1.

Remove the drawer from the drawer housing.

▯ Activate the PTO feature by pushing on the front of

the drawer face. Drawer will open approximately 4

inches.

▯ Pull drawer to fully open position.

▯ Press down right drawer release lever.

▯ Lift up left drawer release lever.

▯ Firmly pull the drawer straight out.

▯ Retract cabinet rails while drawer is removed.

2.

Grasp both sides of the drawer and pulling straight

and level, carefully remove the drawer housing. This

step may require light to moderate force to completely

remove drawer.

3.

Install or service (clean) housing with drawer removed.

Preparing the Storage Drawer for

Installation

Remove the storage drawer from the packaging and

place on a sturdy surface such as a table or workbench.

Take precautions to protect the work surface while

preparing the storage drawer for installation. The

cardboard packaging or some other suitable protector

could be used for this purpose.

Once appliance is properly placed on a prepared work

surface, remove the drawer from the unit. Lay the drawer

to the side taking care to protect the stainless steel

surfaces from damage.

14

Remove Shipping Brackets

Remove the ten (10) screws fastening the shipping

brackets from the housing.

The lower bracket screws can be accessed by turning

the housing on end or sliding forward off the surface

table to gain access to the lower screws and bracket.

A moderate force may be required to pry the top and

bottom outer bracket from the side of the housing since

the screws tend to slightly deform the housing hole

causing slight binding of the bracket.

Note: Take care not to damage or scratch the front

stainless steel cover or side trims.

Discard the two outer and inner shipping brackets and

the ten (10) screws that were just removed. They are no

longer needed for the installation.

Slide the housing into the cabinet opening until the side

trims touch the cabinet face. There is a v-notch on the

top face of the stainless steel front cover to assist in

alignment of the housing to the cabinet opening.

Measure the cabinet opening and adjust the storage

drawer housing by aligning the v-notch with half of the

measured cabinet opening. This will ensure the housing

is centered in the opening.

Once the storage drawer has been aligned to the cabinet

opening, install two (2) supplied screws to secure the

housing to the cabinet face.

With the drawer fully open, drill pilot holes through side

flange with a 1/8” (3.175mm) wood bit before the steam

oven or drawer is installed.

15

Install Steam Oven on Top of Storage

Drawer

Note: Installing the drawer before installing steam oven

may scratch drawer face.

The steam oven must be installed on top of the storage

drawer prior to reinstalling the drawer into the storage

drawer housing. Slide steam oven directly on top of the

storage drawer housing until it is flush with the cabinet.

Refer to the unit installation guide accompanying the

steam oven for detailed installation instructions.

Reinstall the drawer to the storage drawer housing.

Installing Drawer to Housing

The slides mounted to each side of the housing wall

have two moving components, an inner rail and a ball

bearing carrier which need to be in the proper orientation

for accurate installation and alignment.

There is also a visible locking mechanism located at the

rear of each slide.

1.

The slide inner rail should be set to the drawer locked

position for proper installation. With the drawer

removed push the slide inner rail toward the rear of

the housing until it locks in place and does not spring

back to the open position.

Note: A moderate force pushing on the black plastic

ball carrier locking mechanism is required to set the

slide to the drawer locked position. The drawer is

locked when it remains in place and does not spring

back to the open position.

A Ball Bearing Carrier

B Slide Inner Rail

C Locking Mechanism

A Slide Inner Rail

B Locking Mechanism

&%$

$

%

16

2.

Position the drawer assembly in front of the housing

assembly and align the rail to the slide ball carrier

assembly. Keeping the drawer assembly level and

square to the housing, gently insert the drawer to the

housing assembly.

Notes

▯ A slight side-to-side wiggle motion may be required

to properly get the ball bearings to accurately align.

▯ Remember: You are attempting to align two sets of

ball bearings. If more than a moderate force is

required to insert the drawer at this time, remove the

drawer and repeat the installation procedure to this

point.

3.

Continue to insert the drawer keeping the drawer level

and square to the housing until a slight increase in

resistance is felt at the approximate position shown

below.

NOTICES

▯ At this position, a slight increase in closure force is

required with several small increments of force

applied to the drawer to accurately align and set the

drawer for proper operation.

▯ An audible “click” will be heard when the drawer is

properly closed causing the drawer to lock in the

closed position.

4.

Test the operation of the PTO drawer by pushing on

the center lower portion of the drawer front (optimum

location for function). The drawer will operate with an

opening force applied to any location of the drawer

front when outside the recommended location with a

slight increase in force.

$

17

Installation Procedure WD30W

9 CAUTION

Never operate the warming drawer without a front

panel attached. You can attach a Thermador® front

panel or a custom front panel.

9 CAUTION

DO NOT lift the warming drawer by the door’s

handle as this may damage the slides and cause

the door to fit incorrectly.

9 WARNING

DO NOT REPAIR OR REPLACE PARTS

Do not repair or replace any part of the appliance

unless specifically recommended in the manual.

Improper installation, service or maintenance can

cause injury or property damage. Refer to this

manual for guidance. All other servicing should be

done by an authorized servicer.

The electrical outlet can be installed in the back wall

directly behind the warming drawer. A recessed power

receptacle must not exceed 5

1

/

2

ft. (1.7m) maximum

distance from either side of the warming drawer cutout.

Installation clearances permit for the excess power cord

to be coiled behind the appliance.

DO NOT install this warming drawer in wet locations or

outdoors.

9 CAUTION

Before installing, turn power OFF at the service

panel. Lock service panel to prevent power from

being turned ON accidentally.

Preparing the Custom Panel for

Installation

Custom panels must meet the following requirements:

▯ Custom panel is provided by the customer.

▯ Have a handle provided by the customer.

▯ Have a minimum thickness of 3/4” (19 mm).

▯ Have all edges finished.

▯ If using wood, the back must be sealed to prevent

moisture damage.

▯ Be capable of withstanding temperatures above

158°F (70°C).

Custom Panel Front Preparation

1.

Mark pilot holes based on the dimensions in the

template diagram below.

2.

When drilling pilot and clearance holes, be careful not

to drill all the way through the panel. Pilot holes should

only be 10mm (7/16”) deep.

3.

Dimensions are in millimeters (inches).

4.

It is recommended to attach the desired handle/knob

using metal fasteners.

18

Attaching the Custom Panel

The custom front warming drawer comes with an

attachment plate pre-assembled to the unit.

Note: Template dimensions are for reference only. The

panel size is at the customer’s discretion.

Notes

▯ The maximum panel weight is 8 pounds (3.6kg).

▯ Panel thickness is 19.05mm (3/4”) based on U.S.

standard cabinet thickness.

▯ It is recommended that metal fasteners be used.

▯ Dimensions are in millimeters (mm).

Pre-drill pilot and clearance holes in the custom front

panel as explained in the Installation Procedure chapter

and then proceed as follows.

Open the drawer fully by grasping the outer edges of the

attachment plate. Be sure to wear gloves to protect from

cuts from the edges of the attachment plate.

 PP

ë

çʨʚ

èçʨʓʘ

ʎʨʚ



çʨʚ

[

çʨʚ

[

èʨʓʘ

èʨʚ



èçʨʓʘ

é



èèʨʓʘ



ê



$

%

Location Qty. Description

A 4 Counter bore holes 10mm (7/16”) to clear mounting screws (not provided). Depth of bore hole is

also 10mm (7/16”). Be careful not to drill through the panel.

B 8 Pre-drilled to fit mounting screws 2.3mm (1/8”) provided (self-tap screw 8 x 1/2 T20 Truss). Depth

of bore hole is 10mm (7/16”). Be careful not to drill through the panel.

19

Secure the custom panel to the drawer front with eight

(8) #8 x 1/2” T-20 star head screws supplied with the

unit. Tighten the screws but do not overtighten.

Close the drawer. The installation of the custom panel to

the attachment plate is complete.

Continue with the cabinet installation as described in the

Installation Procedure chapter.

Installation Final Check List

▯ Specified clearances maintained to cabinet surfaces.

▯ Drawer handle is level and centered.

▯ Drawer opens and closes properly.

▯ Unit is level.

▯ All packaging material is removed.

▯ Receptacle with correct over-current protection is

provided for service cord connection.

▯ Proper ground connection.

▯ Owner is aware of location of the main circuit breaker.

20

Service

If the warming drawer elements or signal lights do not

turn on, check the power source to see if the circuit

breaker is tripped.

Data Plate

Model SDS30WC

Refer to the data plate on the storage drawer when

requesting service or when contacting Customer Service

for assistance. The data plate is visible on the bottom of

the drawer casing for the SDS30WC storage drawer. It

will be necessary to remove the drawer to view it.

SDS30WC Data Plate Location

The data plate for the SD30WC storage drawer is located

on the left inside of the housing.

SD30WC Data Plate Location

Rating Label-WD30W AND WD30WC

Models SD30WC, WD30WC, WD30W

Refer to the rating label on the appliance when

requesting service or when contacting Customer Service

for assistance. The rating label is visible on the left of the

drawer casing.

Model Number and FD Number

The model number and the FD number of your appliance

are found on the data plate or rating label. Make a note

of these numbers in the space below to save time in the

event your appliance requires service.

Keep your invoice or escrow papers for warranty

validation if service is needed.

Model # FD #

Thermador Customer Support 800-735-4328

La page charge ...

Thermador WD30WC Guide d'installation

Ce manuel convient également à

Thermador WD30WC Guide d'installation

dans d''autres langues

Documents connexes

Autres documents