Whirlpool WED4995EW Mode d'emploi
- Catégorie
- Sèche-linge
- Taper
- Mode d'emploi
W10562352A
W10562353A - SP
ELECTRIC or GAS DRYER
USE AND CARE GUIDE
Table of Contents Table des matières
DRYER SAFETY ............................................................2
CHECK YOUR VENT SYSTEM
FOR GOOD AIR FLOW .................................................4
USE ACCUDRY™/AUTOMATIC DRY CYCLES FOR
BETTER FABRIC CARE AND ENERGY SAVINGS ......4
CONTROL PANEL & FEATURES ..................................5
CYCLE GUIDE ............................................................... 6
USING YOUR DRYER ...................................................7
DRYER CARE ................................................................9
TROUBLESHOOTING .................................................11
WARRANTY ................................................................. 13
ASSISTANCE OR SERVICE .................... BACK COVER
SÉCURITÉ DE LA SÉCHEUSE ...................................14
VÉRIFICATION D’UNE CIRCULATION D’AIR
ADÉQUATE POUR LE SYSTÈME D’ÉVACUATION ..16
UTILISATION DES PROGRAMMES AUTOMATIQUES
POUR UN MEILLEUR SOIN DU TISSU
ET DAVANTAGE D’ÉCONOMIES D’ÉNERGIE ...........16
TABLEAU DE COMMANDE
ET CARACTÉRISTIQUES ...........................................17
GUIDE DE PROGRAMMES ........................................18
UTILISATION DE LA SÉCHEUSE ............................... 19
ENTRETIEN DE LA SÉCHEUSE ................................. 21
DÉPANNAGE. ..............................................................24
GARANTIE. ..................................................................26
ASSISTANCE OU SERVICE. . COUVERTURE ARRIÈRE
SÉCHEUSE
ÉLECTRIQUE ou À GAZ
GUIDE D’UTILISATION
ET D’ENTRETIEN
Para una versión de estas instrucciones en español, visite www.whirlpool.com
2
DRYER SAFETY
3
4
CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW
Good air ow
Along with heat, dryers require good air ow to efciently
dry laundry. Proper venting will reduce your drying times
and improve your energy savings. See “Installation
Instructions.”
The venting system attached to the dryer plays a big role in
good air ow.
Service calls caused by improper venting are not covered
by the warranty and will be paid by the customer, regardless
of who installed the dryer.
Maintain good air ow by:
Good Better
USE ACCUDRY
™
/AUTOMATIC DRY CYCLES FOR BETTER
FABRIC CARE AND ENERGY SAVINGS
Use the ACCUDRY™/Automatic Dry cycles to provide the most energy savings and enhanced fabric care from the dryer.
During ACCUDRY™/Automatic Dry cycles, drying air temperature or moisture level are sensed in the load. This sensing occurs
throughout the drying cycle and the dryer shuts off when the load reaches the selected dryness. The Energy Preferred cycle will
provide optimal energy savings.
With Timed Dry, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to over-drying.
Use Timed Dry for the occasional damp load that needs a little more drying time or when using the drying rack.
n
Cleaning your lint screen before each load.
n
Replace plastic or foil vent material with 4" (102 mm)
diameter heavy, rigid vent material.
n
Use the shortest length of vent possible.
n
Use no more than four 90° elbows in a vent system;
each bend and curve reduces air ow.
n
Remove lint and debris from the exhaust hood.
n
Remove lint from the entire length of the vent system at
least every 2 years. When cleaning is complete, be sure
to follow the “Installation Instructions” supplied with your
dryer for nal product check.
n
Clear away items from the front the dryer.
5
CONTROL PANEL & FEATURES
WRINKLE SHIELD™ Feature (on some models)
When you are unable to remove a load of clothes from the
dryer as soon as it stops, wrinkles can form. The WRINKLE
SHIELD™ feature periodically tumbles, rearranges, and uffs
the load to help keep wrinkles from forming.
n
Get 90minutes of heat-free, periodic tumbling at the end
of a cycle. Turn the WRINKLE SHIELD™ knob to on or off
at any time before the cycle has ended.
DRYER CYCLE KNOB
Use your Dryer Cycle Knob to select available cycles on
your dryer. Turn the knob to select a cycle for your laundry
load. See “Cycle Guide” for detailed descriptions of cycles.
TIMED DRY
Will run the dryer for the specied time on the control.
On models with a selectable temperature knob, you may
choose a setting based on the fabrics in your load. Drying
time and temperature will depend on your dryer model.
ACCUDRY™/AUTOMATIC DRY
Senses moisture in the load or air temperature and shuts
off when the load reaches the selected dryness level.
Gives the best drying in the shortest time. Drying time will
vary based on fabric type, load size, and dryness setting.
1
2
3
TEMPERATURE
Select a drying temperature based on the fabrics in your
load. If you are unsure of the temperature to select for a
load, select the lower setting rather than the higher setting.
NOTE: The No Heat temperature setting (on some models)
is not available on ACCUDRY™ cycles.
CYCLE SIGNAL/PUSH TO START
The Cycle Signal produces an audible sound when the
drying cycle is nished. Promptly removing clothes at the
end of the cycle reduces wrinkling.
Turn the CYCLE SIGNAL knob to select the desired setting
(On or Off). Press the PUSH to START knob to start the
dryer.
NOTE: When the Wrinkle Shield™ setting is selected
and the Cycle Signal is on, the tone will sound every
5minutes until the clothes are removed, or the Wrinkle
Shield™ setting ends.
2 31
4
4
Not all features and options are available on all models.
Appearance may vary.
2
3
4
6
Not all cycles and settings are available on all models.
ACCUDRY™ - Senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness level.
Choose ENERGY PREFERRED cycle for optimal energy savings.
Items to dry:
Temperature:
Available
Options:
Cycle Details:
Wrinkle Shield™
Temperature
Cycle Signal
CYCLE GUIDE — ACCUDRY
™
/AUTOMATIC DRY CYCLES
CYCLE GUIDE — TIMED DRY CYCLES
Items to dry: Temperature:Cycle:
Available
Options:
Cycle Details:
Not all cycles and settings are available on all models.
TIMED DRY - Will run the dryer for the specied time on the control.
Large or heavy items
such as thick towels or
robes
Any load
Heavy Dry
Damp Dry Any
Temperature
Temperature
Choose high to dry large or heavy loads.
Dries items to a damp level or for items
that do not require an entire drying
cycle.
NOTE: If loads do not seem as dry as you would like, select More or Very Dry next time you dry a similar load. If loads seem drier
than you like, select Less Dry next time you dry a similar load.
Casual, shirts, pants,
lightweight items,
synthetics, delicates,
athletic wear
Any
Wrinkle Shield™
Temperature
Cycle Signal
Setting the Drying Temperature
If your dryer has multiple heat settings:
A High temperature setting may be used for drying
heavyweight items such as towels and work clothes.
A Low to Medium temperature setting may be used for drying
medium-weight items such as sheets, blouses, dresses,
underwear, permanent press fabrics, and some knits.
Use the No Heat setting for foam, rubber, plastic, or heat-
sensitive fabrics.
Line dry bonded or laminated fabrics.
NOTE: If you have questions about drying temperatures for
various loads, refer to the care label directions.
Jeans, heavy work
clothes, towels
Energy Preferred
Delicate or Less Dry
Jeans, More, or
Very Dry
Wrinkle Shield™
Temperature
Cycle Signal
Automatic cycles give the best drying
in the shortest time. Drying time varies
based on fabric type, load size, and
dryness setting.
Select a drying temperature based on
the fabrics in your load. If you are unsure
of the temperature to select for a load,
select the lower setting rather than the
higher setting.
Cycle:
High
Medium
Low
Work clothes, medium
weight fabrics, sheets
Rubber, plastic, heat
sensitive fabrics
Fluff Air
No Heat
Temperature
No heat drying.
7
USING YOUR DRYER
1. Clean the lint screen
Clean the lint screen before each load. Pull the lint screen out of
its holder. Roll lint off the screen with your ngers. Do not rinse or
wash screen to remove lint. Push the lint screen rmly back into
place.
For additional cleaning information, see “Dryer Care”.
2. Load the dryer
Place laundry in the dryer. Close the door.
NOTE: Your model may have a different door than the
one shown. Some models have drop down doors.
Do not tightly pack the dryer; clothes should be able to
tumble freely.
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this dryer.
Before using your dryer, wipe the dryer drum with a damp cloth
to remove dust from storing and shipping.
8
6. Press PUSH to START to
begin cycle
Push and hold the PUSH to START knob to begin the cycle.
Promptly remove garments after cycle has completed to reduce
wrinkling. Use the Wrinkle Shield™ feature to avoid wrinkling
when you are unable to remove a load from the dryer as soon
as it stops.
4. Set cycle settings and options
Select cycle settings and options by turning the knob to the
desired position.
NOTE: Not all options and settings are available with all cycles.
Temperature
Turn the TEMPERATURE knob to change the drying
temperature setting. See “Setting the Drying Temperature”.
Wrinkle Shield™ feature (on some models)
n
Get 90 minutes of heat-free, periodic tumbling at the end of
a cycle. Turn the WRINKLE SHIELD™ knob to select on or
off at any time before the cycle has ended.
n
On some models with a WRINKLE SHIELD™ cycle will
automatically get 40 minutes of heat-free, periodic tumbling
at the end of a cycle.
3. Select the desired cycle
Select the desired cycle for your load. See the Cycle Guide
for more information about each cycle.
ACCUDRY™/AUTOMATIC DRY Cycles
You can select a different dryness level, depending on your
load, by turning the knob to dryness level.
Selecting More or Very Dry, ENERGY PREFERRED, or Less Dry
automatically adjusts the dryness level at which the dryer will
shut off. Once a dry level is set, it cannot be changed without
stopping the cycle.
ACCUDRY™/AUTOMATIC DRY cycles give the best drying in
the shortest time. Drying time varies based on fabric type, load
size, and dryness setting.
NOTE: More or Very Dry removes more load moisture.
ENERGY PREFERRED is used for a starting point for
ACCUDRY™ cycles. Choose ENERGY PREFERRED for
optimal energy savings. Less Dry removes less moisture and
used for loads you may want to put on a hanger to complete
drying.
5. Select Cycle Signal (if desired)
Turn the CYCLE SIGNAL knob to select the desired setting
(On or Off). The Cycle Signal produces an audible sound
when the drying cycle is nished. Promptly removing clothes
at the end of the cycle reduces wrinkling.
NOTE: When the Wrinkle Shield™ setting is selected and the
Cycle Signal is on, the tone will sound every 5minutes until
the clothes are removed, or the Wrinkle Shield™ setting ends.
9
DRYER CARE
Keep dryer area clear and free from items that would
block the air ow for proper dryer operation. This includes
clearing piles of laundry in front of the dryer.
Cleaning the lint screen
Every load cleaning
The lint screen is located in the dryer. A screen blocked by
lint can increase drying time.
To clean:
1. Pull the lint screen out of its holder. Roll lint off the
screen with your ngers. Do not rinse or wash screen to
remove lint. Wet lint is hard to remove.
2. Push the lint screen rmly back into place.
IMPORTANT:
n
Do not run the dryer with the lint screen loose,
damaged, blocked, or missing. Doing so can cause
overheating and damage to both the dryer and fabrics.
n
If lint falls off the screen into the dryer during removal,
check the exhaust hood and remove the lint. See
“Venting Requirements.”
As needed cleaning
Laundry detergent and fabric softener residue can build
up on the lint screen. This buildup can cause longer drying
times for your clothes, or cause the dryer to stop before
your load is completely dry. The screen is probably clogged
if lint falls off while the screen is in the dryer.
Clean the lint screen with a nylon brush every 6 months,
or more frequently, if it becomes clogged due to a residue
buildup.
To wash:
1. Roll lint off the screen with your ngers.
2. Wet both sides of lint screen with hot water.
3. Wet a nylon brush with hot water and liquid detergent.
Scrub lint screen with the brush to remove residue
buildup.
4. Rinse screen with hot water.
5. Thoroughly dry lint screen with a clean towel.
Reinstall screen in dryer.
Cleaning the dryer interior
To clean dryer drum
1. Apply a liquid, nonammable household cleaner to the
stained area of the drum and rub with a soft cloth until
stain is removed.
2. Wipe drum thoroughly with a damp cloth.
3. Tumble a load of clean cloths or towels to dry the drum.
NOTE: Garments that contain loose dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the
dryer interior. These stains are not harmful to your dryer and
will not stain future loads of clothes. Dry these items inside
out to avoid drum staining.
Removing accumulated lint
From Inside the Dryer Cabinet
Lint should be removed every 2 years, or more often,
depending on dryer usage. Cleaning should be done
by a qualied servicer.
From the Exhaust Vent
Lint should be removed every 2 years, or more often,
depending on dryer usage.
Cleaning the dryer location
10
Vacation, storage, and moving care
Non-Use or Storage Care
Operate your dryer only when you are at home. If you will
be on vacation or not using your dryer for an extended
period of time, you should:
1. Unplug dryer or disconnect power.
2. (For gas dryers only): Close shut off valve to gas supply
line.
3. Clean lint screen. See “Cleaning the Lint Screen.”
Moving Care
For power supply cord-connected dryers:
1. Unplug the power supply cord.
2. Make sure leveling legs are secure in dryer base.
3. Use tape to secure dryer door.
For direct-wired dryers:
1. Turn off power at fuse or breaker box.
2. Disconnect wiring.
3. Make sure leveling legs are secure in dryer base.
4. Use tape to secure dryer door.
For gas dryers:
1. Unplug or disconnect power to dryer.
2. Close shutoff valve in gas supply line.
3. Disconnect gas supply line pipe and remove ttings
attached to dryer pipe.
4. Cap the open fuel supply line.
5. Make sure leveling legs are secure in dryer base.
6. Use tape to secure dryer door.
Reinstalling the Dryer
Follow the “Installation Instructions” to locate, level,
and connect the dryer.
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
Changing the drum light
(on some models)
1. Unplug dryer or disconnect power.
2. Open the dryer door. Locate the light bulb cover on
the back wall of the dryer. Using a Phillips-head screw
driver, remove the screw located in the lower right-hand
corner of the cover. Remove the cover.
3. Turn bulb counterclockwise. Replace the bulb with
a 10-watt appliance bulb only. Replace the cover and
secure with the screw.
4. Plug into a grounded outlet or reconnect power.
11
First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -
In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.
If you experience
Possible Causes
Solution
TROUBLESHOOTING
Door not closed completely. Make sure the dryer door is closed completely.
Household fuse is blown or circuit
breaker has tripped.
Electric dryers use 2 household fuses or circuit breakers. The
drum may be turning, but you may not have heat. Replace both
fuses or reset the circuit breaker. If the problem continues, call
an electrician.
Dryer will not run
PUSH to START knob not pressed
rmly or held long enough.
Incorrect power supply.
Electric dryers require 240-volt power supply.
Check with a qualied electrician.
Wrong type of fuse.
Use a time-delay fuse.
Unusual sounds
Dryer had a period of non-use.
If the dryer hasn’t been used for awhile, there may be a
thumping sound during the rst few minutes of operation.
Check the front and rear edges of the drum for small objects.
Clean out pockets before laundering.
The four legs are not installed, or the
dryer is not level front to back and
side to side.
The dryer may vibrate if not properly installed.
See “Installation Instructions”.
A coin, button, or paper clip is
caught between the drum and front
or rear of the dryer.
Clothing knotted or balled up.
When balled up, the load will bounce, causing the dryer to
vibrate. Separate the load items and restart the dryer.
Press and hold the PUSH to START knob until you hear the dryer
drum moving.
No heat Household fuse is blown or circuit
breaker has tripped.
The drum may be turning, but you may not have heat. Electric
dryers use 2 household fuses or circuit breakers. Replace both
fuses or reset the circuit breaker. If the problem continues, call
an electrician.
It is a gas dryer.
The gas valve clicking is a normal operating sound.
Supply line valve not open. For gas dryers, make sure the supply line valve is open.
Clothes are not drying
satisfactorily, drying
times are too long
Lint screen clogged with lint.
Lint screen should be cleaned before each load.
Has the Fluff Air cycle or No Heat
temperature setting been selected.
Select the right cycle for the types of garments being dried.
See “Cycle Guide.”
Load too large and heavy to dry
quickly.
Separate the load to tumble freely.
Exhaust vent or outside exhaust
hood clogged with lint, restricting air
movement.
Run the dryer for 5-10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not feel
air movement, clean exhaust system of lint or replace exhaust
vent with heavy metal or exible metal vent. Make sure vent is
not crushed or kinked. See “Installation Instructions”.
Exhaust vent diameter not the
correct size.
Use 4" (102mm) diameter vent material.
Dryer located in a room with
temperature below 45ºF (7ºC).
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
Dryer located in a closet without
adequate opening.
Closet doors must have ventilation openings at the top and
bottom of the door. The front of the dryer requires a minimum
of 1" (25mm) of airspace, and, for most installations, the rear of
the dryer requires 5" (127mm). See “Installation Instructions”.
Exhaust vent not the correct length.
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. Make sure vent
is not crushed or kinked. See “Installation Instructions”.
Fabric softener sheets blocking
the grill.
Use only one fabric softener sheet, and use it only once.
Incorrect power supply.
Electric dryers require 240-volt power supply.
Check with a qualied electrician.
12
First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -
In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.
If you experience
Possible Causes
Solution
TROUBLESHOOTING cont.
Cycle time too short
Automatic cycle ending early. The load may not be contacting the sensor strips. Level the
dryer.
Use Timed Dry for very small loads. Change the Dry Level
setting on ACCUDRY™/Automatic Dry cycles.
Increasing or decreasing the Dry Level setting will change the
amount of drying time in a cycle.
Lint on load
Lint screen clogged.
Lint screen should be cleaned before each load.
Stains on load or drum
Dryer fabric softener not properly
used.
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can stain
your garments.
Drum stains are caused by dyes in clothing (usually blue jeans).
These will not transfer to other clothing.
Loads are wrinkled
Load not removed from dryer at the
end of the cycle.
Select Wrinkle Shield™ feature to tumble the load without heat
to avoid wrinkling.
Dryer tightly packed.
Dry smaller loads that can tumble freely reduce wrinkles from
forming.
Odors
You have recently been painting,
staining, or varnishing in the area
where your dryer is located.
If so, ventilate the area. When the odors or fumes are gone
from the area, rewash and dry the clothing.
The electric dryer is being used for
the rst time.
The new electric heating element may have an odor. The odor
will be gone after the rst cycle.
Load is too hot
Laundry items removed from the
dryer before the end of the cycle.
Allow Cool Down cycle to nish before removing laundry from
dryer. All cycles are cooled slowly to reduced wrinkling and
make it easier to handle. Items removed before Cool Down may
feel very warm.
A high temperature cycle was used,
or a separate temperature control
was set on high.
Select a lower temperature and use an automatic drying cycle.
These cycles sense the temperature or the moisture level in the
load and shut off when the load reaches the selected dryness.
This reduces overdrying.
13
WHIRLPOOL CORPORATION LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions
attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Factory
Specied Replacement Parts and repair labor to correct defects in materials or workmanship that existed when this major appliance
was purchased.
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
Service must be provided by a Whirlpool designated service company. This limited warranty is valid only in the United States or
Canada and applies only when the major appliance is used in the country in which it was purchased. This limited warranty is effective
from the date of original consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is
used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or
repair house fuses, or to correct house wiring or plumbing.
3. Service calls to repair or replace appliance light bulbs, air lters, or water lters. Consumable parts are excluded from warranty
coverage.
4. Damage resulting from accident, alteration, misuse, abuse, re, ood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.
5. Cosmetic damage, including scratches, dents, chips or other damage to the nish of your major appliance, unless such damage
results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.
6. Pick up and delivery. This major appliance is intended to be repaired in your home.
7. Repairs to parts or systems resulting from unauthorized modications made to the appliance.
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized Whirlpool servicer is not available.
9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance
with Whirlpool published installation instructions.
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or
cannot be easily determined.
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and
provinces do not allow limitations on the duration of implied warranties of merchantability or tness, so this limitation may not apply
to you. This warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to
province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow
the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This
warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.
If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.
If you think you need repair service, rst see the “Troubleshooting” section of the Use & Care Guide. If you are unable to resolve
the problem after checking “Troubleshooting,” additional help can be found by checking the “Assistance or Service” section or by
calling Whirlpool. In the U.S.A., call 1 -800 -253-1301. In Canada, call 1-800 -807- 6777. 10/11
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need
it. You will need to know your complete model number and serial
number. You can nd this information on the model and serial
number label located on the product.
Dealer name _____________________________________________
Address __________________________________________________
Phone number ____________________________________________
Model number ____________________________________________
Serial number ____________________________________________
Purchase date ____________________________________________
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the
representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes
with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.
14
SÉCURITÉ DE LA SÉCHEUSE
15
16
VÉRIFICATION D’UNE CIRCULATION D’AIR ADÉQUATE POUR LE SYSTÈME
D’ÉVACUATION
Maintenir une bonne circulation d’air
en effectuant les opérations suivantes :
n
Nettoyer le ltre à charpie avant chaque charge.
n
Remplacer le matériau de conduits d’évacuation en
plastique ou en aluminium par des conduits d’évacuation
lourds et rigides de 4" (102 mm) de diamètre.
n
Toujours employer les conduits d’évacuation les plus
courts possible.
n
Ne pas utiliser plus de quatre coudes à 90° dans un
circuit d’évacuation car chaque inclinaison et courbe
réduit le ux d’air.
n
Retirer la charpie et les résidus du clapet d’évacuation.
n
Retirer la charpie sur toute la longueur du circuit
d’évacuation au moins tous les 2 ans. Après le
nettoyage, veuillez suivre les instructions d’installation
fournies avec la sécheuse pour une vérication nale
de l’appareil.
n
Dégager tout article qui se trouverait devant la sécheuse.
Circulation d’air adéquate
Une sécheuse a besoin de chaleur et d’une circulation
d’air adéquate pour sécher efcacement le linge. Une
ventilation adéquate réduit les durées de séchage et accroît
les économies d’énergie. Voir les Instructions d’installation.
Le système d’évacuation xé à la sécheuse joue un rôle
important dans la circulation de l’air.
Les interventions de dépannage causées par une ventilation
incorrecte ne sont pas couvertes par la garantie et seront
à la charge du client, quel que soit l’installateur de la
sécheuse.
UTILISATION DES PROGRAMMES AUTOMATIQUES ACCUDRY™ POUR UN
MEILLEUR SOIN DU TISSU ET DAVANTAGE D’ÉCONOMIES D’ÉNERGIE
Utiliser les programmes de séchage automatique ACCUDRY™ pour que la sécheuse puisse réaliser davantage d’économies
d’énergie et apporter un soin supérieur aux tissus. Durant les programmes de séchage automatique ACCUDRY™, la température
de séchage de l’air et le niveau d’humidité sont détectés dans la charge. Cette détection se produit tout au long du programme
de séchage et la sécheuse s’éteint lorsque la charge atteint le degré de séchage sélectionné. Le programme Energy Preferred
entraînera des économies d’énergie optimales.
Avec l’option de séchage minuté, la sécheuse fonctionne pendant la durée réglée, ce qui peut parfois entraîner le rétrécissement
ou le froissement du linge, et l’accumulation d’électricité statique due au séchage excessif. Utiliser le séchage minuté pour une
charge encore humide nécessitant un peu de temps supplémentaire ou lorsqu’on utilise la grille de séchage.
Bon
Mieux
17
TABLEAU DE COMMANDE ET CARACTÉRISTIQUES
Caractéristique Wrinkle Shield™
(sur certains modèles)
Lorsqu’on ne peut pas enlever une charge de la sécheuse
dès qu’elle s’arrête, des faux plis peuvent se former. La
caractéristique WRINKLE SHIELD™ effectue un culbutage
de la charge, la réagence et l’aère à intervalles réguliers
pour aider à éviter la formation de faux plis.
n
Obtenez 90 minutes de culbutage périodique sans
chaleur à la n d’un programme. Appuyer sur
le bouton WRINKLE SHIELD™ pour ACTIVER ou
DÉSACTIVER cette fonction à tout moment avant
la n d’un programme.
BOUTON DE PROGRAMME DE LA SÉCHEUSE
Utiliser le bouton de programme de séchage pour
sélectionner les programmes disponibles sur la sécheuse.
Tourner le bouton de programme pour sélectionner un
programme correspondant à la charge de linge. Voir “Guide
de programmes” pour des descriptions de programmes
détaillées.
Séchage minuté
Ceci fait fonctionner la sécheuse pour la durée spéciée
sur le module de commande. Pour les modèles
dotés d’un bouton de sélection de température, vous
pouvez choisir un réglage en fonction des tissus de
votre charge. Le temps de séchage et la température
dépendront du modèle de votre sécheuse.
1
2
3
Programmes automatiques avec la
caractéristique ACCUDRY™
Détecte l’humidité de la charge et la température de l’air
et s’éteint lorsque la charge a atteint le degré de séchage
sélectionné. Permet d’obtenir le meilleur rendement de
séchage en un minimum de temps. Le temps de séchage
variera en fonction du type de tissu, du volume de la
charge et du réglage de séchage.
TEMPERATURE (température)
Choisir une température de séchage en fonction des
tissus de votre charge. Si vous hésitez sur la température à
sélectionner pour une charge donnée, choisir le réglage plus
bas plutôt que le réglage plus élevé.
REMARQUE : La caractéristique No Heat (sans chaleur)
n’est pas disponible sur les programmes de séchage
automatique ACCUDRY™.
CYCLE SIGNAL/PUSH to START (signal de
programme/enfoncer pour mettre en marche)
Le signal de n de programme émet un signal sonore qui
indique la n du programme de séchage. Le fait de
sortir rapidement les vêtements à la n du programme
permet de réduire le froissement.
Tourner le bouton CYCLE SIGNAL (signal de programme)
pour activer ou désactiver le réglage désiré. Appuyer sur le
bouton PUSH TO START (enfoncer pour mettre en marche)
pour mettre la sécheuse en marche.
REMARQUE : Lorsque le réglage Wrinkle Shield™ est
sélectionné et que le signal de programme est activé,
un signal sonore retentit toutes les 5 minutes jusqu’à
ce que les vêtements soient retirés, ou que le réglage
Wrinkle Shield™ se termine.
4
Certains programmes et options ne sont pas disponibles sur certains modèles.
L’apparence des appareils peut varier.
2 31 4
2
3
4
18
Certains programmes ne sont pas disponibles sur certains modèles.
SÉCHAGE AUTOMATIQUE ACCUDRY™ - Détecte l’humidité présente dans la charge ou la température de l’air et s’éteint lorsque
la charge atteint le degré de séchage sélectionné. Sélectionner ENERGY PREFERRED (éconergique) pour des économies d’énergie
optimales.
Articles à sécher :
Température
tissu :
Options
disponibles :
Détails du programme :
Energy Preferred
Delicate (articles
délicats) ou Less
Dry (moins sec)
Temperature Fabric
Wrinkle Shield™
Cycle Signal
GUIDE DE PROGRAMMES — ACCUDRY™/PROGRAMMES AUTOMATIQUES
GUIDE DE PROGRAMMES — SÉCHAGE MINUTÉ
Articles à sécher :
Programme : Température
de séchage :
Options
disponibles :
Détails du programme :
Certains programmes ne sont pas disponibles sur certains modèles.
TIMED DRY (séchage minuté) - Fait fonctionner la sécheuse pour la durée spéciée sur le module de commande.
Articles lourds ou
volumineux tels que
serviettes épaisses ou
peignoirs
N’importe quelle
charge
Heavy Dry
Damp Dry
N’importe laquelle
Temperature
Temperature
Sélectionner high (élevé) pour sécher des
charges importantes ou lourdes.
Sèche les articles à un degré d’humidité
ou les articles qui ne nécessitent pas un
programme de séchage complet.
REMARQUE : Si les charges ne semblent pas aussi sèches que désiré, sélectionner More Dry (plus sec) ou Very Dry (très sec)
la prochaine fois que l’on sèche une charge semblable. Si les charges semblent plus sèches que désiré, sélectionner Less Dry
(moins sec) la prochaine fois que l’on sèche une charge semblable.
Tout-aller, chemisiers,
pantalons, articles légers,
synthétiques, tissus
délicats, vêtements de
sport
N’importe laquelle
Temperature Fabric
Wrinkle Shield™
Cycle Signal
Réglage de la température de séchage
Si la sécheuse comporte plusieurs réglages de chaleur :
On peut utiliser un réglage de chaleur High (élevée) pour
sécher les articles lourds tels que les serviettes et les
vêtements de travail.
Un réglage de chaleur Low (bas) à Medium (moyen) peut être
utilisé pour sécher les articles moyennement lourds tels que
draps, chemisiers, robes, sous-vêtements, tissus à pressage
permanent et certains tricots.
Utiliser le réglage No Heat (sans chaleur) pour la mousse, le
caoutchouc, le plastique ou les tissus sensibles à la chaleur.
Sécher sur une corde à linge les tissus doublés ou
multicouches.
REMARQUE : Pour toute question concernant les
températures de séchage pour diverses charges, consulter
les instructions sur l’étiquette de soin.
Jeans, vêtements de travail
lourds, serviettes
Jeans, More, or
Very Dry
(très sec, plus sec
ou très sec)
Temperature Fabric
Wrinkle Shield™
Cycle Signal
Permet d’obtenir le meilleur rendement de
séchage en un minimum de temps. Le temps
de séchage variera en fonction du type de
tissu, du volume de la charge et du réglage de
séchage.
Choisir une température de séchage en
fonction des tissus de votre charge. Si vous
hésitez sur la température à sélectionner pour
une charge donnée, choisir le réglage le plus
bas plutôt que le réglage le plus élevé.
Niveau de
séchage :
High
(élevé)
Medium
(moyen)
Low
(bas)
Vêtements de travail,
articles moyennement
lourds, draps
Caoutchouc, plastique,
tissus sensibles à la
chaleur
Fluff Air
No Heat
(sans chaleur)
Temperature
Séchage sans chaleur.
Options de Température de
séchage :
Very Dry (très sec)
Energy Preferred (éconergique)
Less Dry (moins sec)
Heavy Dry (séchage intense)
Options disponibles :
Temperature température)
Wrinkle Shield™ (antifroissement)
Cycle Signal (signal de programme)
Time Adjustment (ajustement de la durée)
Damp Dry (séchage humide)
Tumble Press (pressage par culbutage)
Fluff Air (duvetage à l’air)
19
UTILISATION DE LA SÉCHEUSE
1. Nettoyer le ltre à charpie
Nettoyer le ltre à charpie avant chaque charge. Enlever le ltre
à charpie en le tirant tout droit vers le haut. Enlever la charpie
du ltre en la roulant avec les doigts. Ne pas rincer ni laver le ltre
pour enlever la charpie. Remettre le ltre à charpie fermement en
place.
Pour plus d’informations sur le nettoyage, voir “Entretien de la
sécheuse”.
2. Charger la sécheuse
Placer le linge dans la sécheuse. Fermer la porte.
REMARQUE : La porte de votre modèle peut différer de celle
gurant sur l’illustration. Certains modèles peuvent comporter
des portes à ouverture vers le bas.
Ne pas surcharger la sécheuse; les vêtements doivent pouvoir
culbuter librement.
AVERTISSEMENT : Pour réduire le risque d’incendie, de choc
électrique ou de blessures à autrui, lire les IMPORTANTES
INSTRUCTIONS DE SÉCURITÉ avant de faire fonctionner cette
sécheuse.
Avant d’utiliser la sécheuse, essuyer le tambour de la sécheuse
avec un linge humide pour enlever la poussière accumulée au
cours de l’entreposage et de l’expédition.
20
4. Sélectionner les réglages et
options du programme
Sélectionner les réglages et options du programme en tournant
le bouton sur la position souhaitée.
REMARQUE : Tous les réglages et options ne sont pas
disponibles avec tous les programmes.
TEMPERATURE (température)
Tourner le bouton TEMPERATURE (température) pour modier
le réglage de la température de séchage. Voir “Réglage de la
température de séchage ”.
Caractéristique Wrinkle Shield™ (antifroissement)
(sur certains modèles)
n
Obtenez 90 minutes de culbutage périodique sans chaleur
à la n d’un programme. Tourner le bouton WRINKLE
SHIELD™ pour ACTIVER ou DÉSACTIVER cette fonction
à tout moment avant la n d’un programme.
n
Sur les modèles dotés de l’option WRINKLE SHIELD™
(antifroissement), le programme ajoute automatiquement
40 minutes de culbutage périodique sans chaleur à la n
d’un programme.
3. Sélectionner le programme désiré
Sélectionner le programme souhaité pour la charge.Voir le
Guide de programmes pour plus d’informations sur chaque
programme.
PROGRAMMES DE SÉCHAGE AUTOMATIQUE ACCUDRY™
Selon votre charge, vous pouvez sélectionner un degré de
séchage différent en tournant le bouton sur le degré de
séchage.
Lorsqu’on sélectionne More or Very Dry (plus sec ou très sec),
ENERGY PREFERRED (éconergique), ou Less Dry (moins sec),
le degré de séchage qui commandera l’arrêt de la sécheuse
est automatiquement ajusté. Après avoir sélectionné un
certain degré de séchage, il est impossible de le modier
sans arrêter le programme.
Les programmes de séchage automatique ACCUDRY™
offrent un séchage idéal en un minimum de temps. La durée
de séchage varie en fonction du type de tissu, de la taille de
la charge et du réglage de niveau de séchage.
REMARQUE : Le séchage More or Very Dry (plus sec ou très
sec) élimine davantage d’humidité dans la charge. ENERGY
PREFERRED est utilisé comme point de départ dans les
programmes ACCUDRY™. Sélectionner ENERGY PREFERRED
pour réaliser des économies d’énergie optimales. Le séchage
Less Dry (moins sec) élimine moins d’humidité et est utilisé
pour les charges que l’on souhaite placer sur un cintre pour
qu’elles nissent de sécher.
5. Sélectionner le signal de
programme (si désiré)
Tourner le bouton CYCLE SIGNAL (signal de programme)
pour ACTIVER ou DÉSACTIVER le signal. Le signal de
programme est un signal sonore qui retentit lorsque le
programme de séchage est terminé. Sortir rapidement les
vêtements à la n du programme réduit le froissement.
REMARQUE : Lorsque le réglage Wrinkle Shield™ est
sélectionné et que le signal de programme est activé, un
signal sonore retentit toutes les 5 minutes jusqu’à ce que les
vêtements soient retirés, ou que le réglage Wrinkle Shield™
se termine.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Whirlpool WED4995EW Mode d'emploi
- Catégorie
- Sèche-linge
- Taper
- Mode d'emploi
dans d''autres langues
- English: Whirlpool WED4995EW User guide