Labconco Protector Airo 184410000 Series Manuel utilisateur

Original instructions

Protector

®

Echo™ &

Protector

®

Airo™

Filtered Fume Hoods

Models

180 Series – 4', 5', 6' and 8' (Echo)

181 Series – 4', 5', 6' and 8' with side glass (Echo)

182 Series – 4', 5', 6' and 8' with 360 degree visibility (Echo)

183 Series – 4', 5', 6' and 8' Floor-Mount only (Echo)

184 Series – 3' and 4' small height models only (Airo)

Original instructions

the right to make periodic design changes without obligation to notify any person or entity of such change.

Returned or Damaged Goods

Do not return goods without the prior authorization from Labconco. Unauthorized returns will not be

accepted. If your shipment was damaged in transit, you must file a claim directly with the freight carrier.

Labconco Corporation and its dealers are not responsible for shipping damages.

The United States Interstate Commerce Commission rules require that claims be filed with the delivery

carrier within fifteen (15) days of delivery.

Limitation of Liability

The disposal and/or emission of substances used in connection with this equipment may be governed by

various federal, state, or local regulations. All users of this equipment are required to become familiar with

any regulations that apply in the user’s area concerning the dumping of waste materials in or upon water,

land, or air and to comply with such regulations. Labconco Corporation is held harmless with respect to

user’s compliance with such regulations.

Contacting Labconco Corporation

If you have questions that are not addressed in this manual, or if you need technical assistance, contact

Labconco’s Customer Service Department or Labconco’s Product Service Department at 1-800-821-5525

or 1-816-333-8811, between the hours of 7:30 a.m. and 5:30 p.m., Central Standard Time.

Part #9411500, Rev. F

ECO L352

Warranty

Labconco Corporation provides a warranty to the original buyer for the repair or replacement of parts and

reasonable labor as a result of normal and proper use of the equipment with compatible chemicals. Broken

glassware and maintenance items, such as filters, gaskets, light bulbs, finishes and lubrication are not

warranted. Excluded from warranty are products with improper installation, erratic electrical or utility supply,

unauthorized repair and products used with incompatible chemicals.

The warranty for Protector

®

Echo™ & Protector

®

Airo™ Filtered Fume Hoods will expire one year from date

of installation or two years from date of shipment from Labconco, whichever is sooner. Warranty is non-

transferable and only applies to the owner (organization) of record.

Buyer is exclusively responsible for the set-up, installation, verification, decontamination or calibration of

equipment. This limited warranty covers parts and labor, but not transportation and insurance charges. If the

failure is determined to be covered under this warranty, the dealer or Labconco Corporation will authorize

repair or replacement of all defective parts to restore the unit to operation. Repairs may be completed by 3

rd

party service agents approved by Labconco Corporation. Labconco Corporation reserves the rights to limit this

warranty based on a service agent’s travel, working hours, the site’s entry restrictions and unobstructed access

to serviceable components of the product.

Under no circumstances shall Labconco Corporation be liable for indirect, consequential, or special damages

of any kind. This warranty is exclusive and in lieu of all other warranties whether oral, or implied.

Original instructions

TABLE OF CONTENTS

CHAPTER 1: INTRODUCTION 1

Model Number Configurator 2

About This Manual 3

Typographical Conventions 4

Your Next Step 5

CHAPTER 2: PREREQUISITES 6

Location Requirements 7

Support Requirements 7

Filtration Technology Airflow and Power Requirements 7

Electrical Requirements 8

Service Line Requirements 8

Space Requirements 8

Commissioning, Setup and Startup Requirements 8

CHAPTER 3: GETTING STARTED 9

Unpacking Your Fume Hood 10

Removing the Shipping Skid 10

Sash Weight Release 11

Installing the Hood on a Supporting Structure and Work Surface 11

Connecting the Electrical Supply Source to the Protector Hood 13

Connecting the Service Lines to the Protector Hood 15

Sealing the Protector Hood to the Work Surface 16

Setting up the Protector Echo Floor-Mounted Filtered Hood 16

Commissioning the Filtration Technology 17

Re-Configuration Process 27

Troubleshooting Guide for GFH 43

Certifying the Protector Filtered Fume Hood 46

CHAPTER 4: PERFORMANCE FEATURES AND SAFETY

PRECAUTIONS 47

Performance Features 47

Safety Precautions 51

Original instructions

CHAPTER 5: USING THE PROTECTOR FILTERED HOOD 59

Access Cards 59

Starting the Filtered Hood 60

Operating the Vertical-Rising Sash 60

The Modular Neutrodine Filtration 60

Detecting a Breakthrough 61

Communication 63

User Options and Approved Chemicals 64

Working in Your Protector Filtered Fume Hood 64

CHAPTER 6: MAINTAINING THE PROTECTOR

FILTERED HOOD 66

Routine Maintenance Schedule 66

Initial Certification 67

Re-Certification 67

User Alarm Code List 67

Tool List 70

Neutrodine SDS for Disposal 71

Partial Filter Replacement Procedure 73

Reconfiguration Process 87

Light and/or Circuit Board Replacement 88

Fan and/or Circuit Board Replacement 90

Fan Box Replacement 92

Electro (Acid) Sensor Replacement 95

Secure Mode 103

gGuard Checklist and Software Option 104

BACnet Checklist Option 104

CHAPTER 7: ACCESSORIZING THE PROTECTOR

FILTERED HOOD 105

Filters 105

Work Surfaces 106

Base Stands, Accessory Shelves, Seismic Supports, and

Hydraulic Lift Base Stands 107

Storage Cabinets 108

Installing Additional Service Fixtures 108

Installing an Electrical Duplex Outlet 110

Installing Optional Guardian™ Digital Airflow Monitor 111

Sash Stop Kit – Field Installation 111

Distillation Grids – Field Installation 112

Installing Remote Monitoring Software 112

Installing BACnet Gateway Hardware 113

ADA Remote Control 113

Additional User, Maintenance, and Administrator Access Cards 113

Sash Reduction Wing Kits 114

CHAPTER 8: TROUBLESHOOTING 115

Original instructions

APPENDIX A: PROTECTOR FILTERED HOOD

REPLACMENT COMPONENTS 118

Protector Echo Filtered Hood Replacement Parts 118

Neutrodine Filtration Technology Replacement Parts 119

APPENDIX B: PROTECTOR FILTERED HOOD DIMENSIONS 122

APPENDIX C: PROTECTOR FILTERED HOOD

SPECIFICATIONS 125

APPENDIX D: SERIAL NUMBER TAG DESCRIPTION 127

APPENDIX E: gGUARD 133

APPENDIX F: BACnet 148

APPENDIX G: SECURE MODE 151

APPENDIX H: CHEMICAL GUIDE 155

APPENDIX I: REFERENCES 171

APPENDIX J: SETTING UP THE PROTECTOR ECHO

FLOOR-MOUNTED FILTERED HOOD 173

APPENDIX K: SMALL 54.2" HEIGHT AIRO DIMENSIONS 185

Product Service 1-800-522-7658

1

Original instructions

CHAPTER 1

INTRODUCTION

Congratulations on your purchase of a Labconco Protector

®

Echo™ or Protector

®

Airo™ Filtered Fume Hood which is unique as it is built on a traditional fume

hood platform along with Neutrodine

®

Filters that handle solvents, acids, and bases

with one comprehensive filter. From here on in this manual, the Protector Airo

only refers to the shorter height 3' and 4' widths with 54.2" exterior height. It

offers a comfortable workspace for users accustomed to the space and utility of a

standard ducted fume hood, but in the realm of a filtered fume hood. The Protector

Filtered Fume Hood solves the problem of ducting in laboratories that are difficult

to vent because of location. The Protector Filtered Fume Hood combines its

patented (U.S. Patent No. 6,461,233) fully featured, containment-enhancing fume

hood design with Neutrodine (by Erlab) filtration technology to deliver a multi-use

ductless fume hood. The Protector Filtered Fume Hood meets the definition of

SEFA 9 DH3 ductless hoods because of its sensor package, backup filters, and

communication. Building communication is one of the most important aspects of

the Protector Filtered Fume Hood. In the event of loss of airflow, damage of a

primary filter, or if a leak reaches the second set of redundant filters for any

reason, an alarm will sound and the communication system will alert a designated

email address. The designated safety officer could be made aware of the problem

immediately through any internet-enabled smart phone, tablet or computer. Large

laboratories and labs where a single safety manager must handle multiple concerns

will benefit most from this proactive safety system.

The Labconco Protector Filtered Fume Hood has been engineered to provide

maximum visibility in a laboratory, and effectively contain toxic, noxious, or other

harmful materials when properly installed. The Protector Filtered Fume Hood

offers many unique features to enhance safety, performance, and visibility. To

take full advantage of them, please acquaint yourself with this manual and keep it

handy for future reference. If you are unfamiliar with how fume hoods operate,

please review Chapter 4: Performance Features and Safety Precautions before

you begin working in the fume hood. Even if you are an experienced fume hood

user, please review Chapter 5: Using Your Protector Filtered Hood, which

describes your filtered hood’s features so that you can efficiently use the hood.

Chapter 1: Introduction

Product Service 1-800-522-7658

2

Original instructions

Model Number Configurator

Example:

Product Line Family Configuration Width Depth Airfoil Sash System Electrical Accessories

Fume Hood 1 Filtered Hood 8 BT None 0 4' 4 37.7" BT & FM 1 Eco-Foil 0 Cable 0 115V 0 None 0

BT Sides 1 5' 5 43.7" FM 2 Flush (Special) 4 Chain BT only 1 230V 2 2 Fixtures 1

BT 360 2 6' 6 55.7" FM 3 None-FM only 7 (Special) 2 Fix & 1 GFCI 2

FM None 3 8' 8 (8'-2 GFCI)

Airo/BT Small 4 3' 3

31.7" BT, 0

Height small 3' only

Airo

BT= Benchtop

FM= Floor Mount

2

0

1

0

1

4

0

8

Figure 1-1

Chapter 1: Introduction

Product Service 1-800-522-7658

3

Original instructions

About This Manual

This manual is designed to help you learn how to install, use, and maintain your

filtered fume hood. Instructions for installing optional equipment on your hood are

also included.

Chapter 1: Introduction provides a brief overview of the filtered fume hood,

explains the organization of the manual, and defines the typographical conventions

used in the manual.

Chapter 2: Prerequisites explains what you need to do to prepare your site before

you install your filtered fume hood. Electrical and service requirements are

discussed.

Chapter 3: Getting Started contains the information you need to properly unpack,

inspect, install, and certify your filtered fume hood.

Chapter 4: Performance Features and Safety Precautions explains how the

Protector Filtered Hood operates and the appropriate precautions you should take

when using the fume hood.

Chapter 5: Using Your Protector Filtered Hood discusses the basic operation of

your filtered fume hood. Information on how to prepare, use and shut down your

Protector Filtered Hood are included.

Chapter 6: Maintaining Your Protector Filtered Hood explains how to perform

routine maintenance on your filtered fume hood.

Chapter 7: Modifying Your Protector Filtered Hood explains how to modify the

filtered fume hood or add accessories.

Chapter 8: Troubleshooting contains a table of problems you may encounter while

using your filtered fume hood including the probable causes of the problems and

suggested corrective actions.

Appendix A: Protector Filtered Hood Components contains labeled diagrams of all

of the components of the filtered fume hoods.

Appendix B: Protector Filtered Hood Dimensions contains comprehensive

diagrams showing all of the dimensions for the filtered fume hoods.

Appendix C: Protector Filtered Hood Specifications contains the electrical

requirements for the filtered fume hood. Wiring diagrams are also included.

Appendix D: Serial Number Tag Description provides current rating code used on

serial number tag.

Chapter 1: Introduction

Product Service 1-800-522-7658

4

Original instructions

Appendix E: gGuard

Appendix F: BACnet

Appendix G: Secure Mode

Appendix H: Chemical Guide

Appendix I: References lists the various resources available that deal with filtered

fume hoods.

Typographical Conventions

Recognizing the following typographical conventions will help you understand and

use this manual:

 Book, chapter, and section titles are shown in italic type (e.g., Chapter 3:

Getting Started).

 Steps required to perform a task are presented in a numbered format.

 Comments located in the margins provide suggestions, reminders, and

references.

 Critical information is presented in boldface type in paragraphs that are

preceded by the exclamation icon. Failure to comply with the information

following an exclamation icon may result in injury to the user or permanent

damage to fume hood.

 Les informations critiques sont présentées en gras dans les paragraphes qui

sont précédés par l'icône d'exclamation. Ne pas se conformer aux informations

qui suivent une icône d'exclamation peut résulter à la blessure de l'utilisateur

ou à des dommages irréversibles de la hotte aspirante.

 Critical information is presented in boldface type in paragraphs that are

preceded by the wrench icon. These operations should only be performed by a

trained certifier or contractor. Failure to comply with the information

following a wrench icon may result in injury to the user or permanent damage

to your hood.

 Les informations critiques sont présentées en gras dans les paragraphes qui

sont précédés par l'icône de clé plate. Ces opérations devraient être seulement

exécutées par un professionnel agrée. L'échec pour se conformer aux

informations qui suivent une icône de clé plate peut résulter à la blessure de

l'utilisateur ou à des dommages irréversibles de la hotte.

 Important information is presented in capitalized type in paragraphs that are

preceded by the pointer icon. It is imperative that the information contained in

these paragraphs be thoroughly read and understood by the user.



!

Chapter 1: Introduction

Product Service 1-800-522-7658

5

Original instructions

 CAUTION – See Manual. When this symbol is on a fume hood it indicates a

caution that is detailed in this manual.

 PRUDENCE – Consulter le Manuel. Quand ce symbole est sur une hotte

aspirante, il indique une prudence qui est détaillée dans ce manuel.

 CAUTION – Hot Surface

 AVERTIR – Surface Chaude

 CAUTION – See Manual. This symbol on the fume hood indicates the

possibility of a pinch hazard.

 PRUDENCE – Consulter le Manuel. Ce symbole sur la hotte indique la

possibilité d'un risque de pincement.

Your Next Step

If your Filtered Fume Hood needs to be installed, proceed to Chapter 2:

Prerequisites to ensure your installation site meets all of the requirements. Then,

go to Chapter 3: Getting Started for instructions on how to install your filtered

fume hood and make all of the necessary connections.

If you would like to review how filtered fume hoods operate, go to Chapter 4:

Performance Features and Safety Precautions.

For information on the operational characteristics of your filtered fume hood, go to

Chapter 5: Using Your Protector Filtered Hood.

If your filtered fume hood is installed and you need to perform routine

maintenance on the cabinet, proceed to Chapter 6: Maintaining Your Protector

Filtered Hood.

For information on making modifications to the configuration of your fume hood,

go to Chapter 7: Modifying Your Protector Filtered Hood.

Refer to Chapter 8: Troubleshooting if you are experiencing problems with your

filtered fume hood.

!

Product Service 1-800-522-7658

6

Original instructions

CHAPTER 2

PREREQUISITES

Before you install your filtered fume hood, you need to prepare your site for

installation. Carefully examine the location where you intend to install your

hood. You must be certain that the area is level and of solid construction. In

addition, a dedicated source of electrical power must be located near the

installation site.

Carefully read this chapter to learn the requirements for your installation site:

 The location requirements.

 The support requirements.

 The Filtration Technology airflow and power requirements.

 The electrical power requirements.

 The service line requirements.

 The space requirements.

 The commissioning and setup requirements.

Refer to Appendix B: Protector Filtered Hood Dimensions for complete fume

hood dimensions.

Refer to Appendix C: Protector Filtered Hood Specifications for complete filtered

fume hood electrical and environmental conditions, specifications and

requirements.

Chapter 2: Prerequisites

Product Service 1-800-522-7658

7

Original instructions

Location Requirements

The filtered fume hood should be located away from traffic

patterns, doors, windows, fans, ventilation registers, and any

other air-handling device that could disrupt its airflow

patterns. All windows in the room should be closed.

La hotte filtrée devrait être situé loin des modèles de trafic,

portes, fenêtres, ventilateurs, registres de ventilation, et tout

autre dispositif de traitement de l'air qui pourraient perturber

ses modèles de flux d'air. Toutes les fenêtres de la chambre

doivent être fermés.

Support Requirements

ALL Protector Hood installations are usually permanent and

stationary. The supporting structure usually consists of a base

cabinet and chemically-resistant work surface. If needed, the

Protector Hood may be placed on a cart or mobile bench.

Toutes les installations Protecteur de capot sont généralement

permanent et stationnaire. La structure de support est

généralement constitué d'une armoire de base et la surface de

travail résistant aux produits chimiques. Si nécessaire, le Si

nécessaire, le Protecteur du capot peut être placé sur un

chariot ou un banc mobile.

Filtration Technology Airflow and Power

Requirements

Hood

width

Airflow

(CFM)

Makeup

Air (CFM)

Face

Velocity

(fpm)

No. of

modules

Fan

Power

(watts)

Light

Power

(watts)

Total

Power

(watts)

3'

Up to

130

0, limited to

min. volume

required by

local

regulations

and min.

laboratory air

change

requirements.

60-100

1

36

18

54

4'

Up to

260

60-100

2

72

36

108

5'

Up to

390

60-100

3

108

54

162

6'

Up to

520

60-100

4

144

72

216

8'

Up to

650

60-100

5

180

90

270

!

Chapter 2: Prerequisites

Product Service 1-800-522-7658

8

Original instructions

Electrical Requirements

The Protector Filtered Hood models feature internal wiring for the fluorescent lights,

fans, and control panel. All internal wiring is terminated with a simple plug in wall

cord. The blower switch and light switch wires are part of the control panel. Refer

to Chapter 3: Getting Started and Appendix C: Protector Filtered Hood

Specifications for the wiring diagram for proper electrical installation.

Les modèles Protector Filtré capot disposent câblage interne pour les lumières,

ventilateurs, et le panneau de contrôle fluorescent. Tout le câblage interne est

terminé avec un simple plug-in cordon de mur. L'interrupteur de la soufflerie et

fils de l'interrupteur de lumière font partie du panneau de contrôle. Reportez-vous

au Chapitre 3: Mise en route et à l'Annexe C: Protector filtrée capot Spécifications

pour le schéma de câblage pour l'installation électrique appropriée.

Service Line Requirements

All service lines to the filtered fume hood should be ¼ inch outside diameter,

copper (brass for natural gas), and equipped with an easily accessible shut-off

valve, should disconnection be required. Recommended operating pressure is 40

PSI, with a maximum allowable pressure of 200 PSI. Consider a pressure

regulator to reduce line pressure to 40 PSI. Please check with local codes for

other requirements.

Space Requirements

The dimensions for the different models are shown in Appendix B: Protector

Filtered Hood Dimensions.

Commissioning, Setup and Startup

Requirements

All commissioning for the Protector Filtered Hood requires installation, setup,

startup and configuration of the Filtration Technology. Certifying the Protector

Filtered Hood should be completed for final commissioning. Refer to Chapter 3:

Getting Started for specifics on completing commissioning.

Product Service 1-800-522-7658

9

Original instructions

CHAPTER 3

GETTING STARTED

Now that the site for your filtered fume hood is properly prepared, you are ready

to unpack, inspect, install, and certify your unit. Read this chapter to learn how

to:

 Unpack and move your Protector Hood.

 Set up the filtered fume hood with the supporting structure and work surface.

 Connect the electrical supply source.

 Connect the service lines.

 Sealing the Protector Hood to the work surface.

 Commissioning the Filtration Technology.

 Re-configuration process (first time setup and replacing components).

 Arrange certification of your Protector Hood.

Depending upon which model you are installing, you may need common

plumbing and electrical installation tools in addition to 5/16", 3/8", 7/16", and

1/2" wrenches, ratchets, sockets, a nut driver set, a flat-blade screwdriver, a

Phillips screwdriver, and a carpenter level to complete the instructions in the

chapter.

The Protector Hood models weigh between 400 to 835 lbs.

(182-375 kg). The shipping skid allows for lifting with a

mechanical lift truck or floor jack. If you must lift the fume

hood manually, follow safe-lifting guidelines. Normally, the

fume hood can be slid off a hydraulic lift table and be placed

into position on top of the work surface. Do not lift by the

front air foil.

Les modèles Protector capot pèsent entre 400 à 835 livres. (182

à 375 kg). La palette d'expédition permet de levage avec un

chariot élévateur mécanique ou prise de parole. Si vous devez

soulever la hotte manuellement, suivre les directives de

sécurité-levage. Normalement, la hotte peut être glissé sur une

table de levage hydraulique et être placé en position au-dessus

de la surface de travail. Ne pas soulever par la feuille d'air

avant.

!

Chapter 3: Getting Started

Product Service 1-800-522-7658

10

Original instructions

Unpacking Your Fume Hood

Carefully remove the shrink-wrap or carton on your fume hood and inspect it for

damage that may have occurred in transit. All the filtration fans and lights are

packaged in boxes on top of the hood liner and should not be discarded. If

your unit is damaged, notify the delivery carrier immediately and retain the entire

shipment intact for inspection by the carrier.

DO NOT RETURN GOODS WITHOUT THE PRIOR

AUTHORIZATION OF LABCONCO. UNAUTHORIZED

RETURNS WILL NOT BE ACCEPTED.

IF YOUR HOOD WAS DAMAGED IN TRANSIT, YOU MUST

FILE A CLAIM DIRECTLY WITH THE FREIGHT CARRIER.

LABCONCO CORPORATION AND ITS DEALERS ARE NOT

RESPONSIBLE FOR SHIPPING DAMAGES.

Do not discard the shipping skid, fan boxes, harnesses, or packing material for

your filtered fume hood until you have checked all of the components and

installed and tested the unit. Do not remove the filtered fume hood from its

shipping skid until it is ready to be placed into its final location. Move the unit by

placing a flat, low dolly under the shipping skid, or by using a floor jack.

Do not move the hood by tilting it onto a hand truck.

Ne pas déplacer la hotte en le penchant sur un diable.

Removing the Shipping Skid

LEAVE THE FUME HOOD ATTACHED TO ITS SHIPPING

SKID UNTIL IT IS AS CLOSE TO ITS FINAL LOCATION AS

POSSIBLE. MOVE THE HOOD BY USING A SUITABLE

FLOOR JACK, OR BY PLACING A FURNITURE DOLLY

UNDERNEATH THE SKID. DO NOT MOVE THE HOOD BY

TILTING IT ONTO A HAND TRUCK.

After you verify the fume hood components, move your hood to the location

where you want to install it. Should you require disassembly to move the hood,

then follow the instructions in Appendix F. Then, follow the steps listed next to

remove the shipping skid from your unit.

1. Remove the side panels by unscrewing the Phillips screws.

2. Find the hardware (bolts, washers, nuts) that attach the fume hood to

the skid and remove the hardware. Some hardware is on the sides and

some is on the back.

The United

States

Interstate

Commerce

Commission

rules require

that claims

be filed with

the delivery

carrier

within fifteen

(15) days of

delivery.

!



Chapter 3: Getting Started

Product Service 1-800-522-7658

11

Original instructions

Sash Weight Release

To protect the fume hood from damage in shipment, the sash weight has been

secured to the back of the fume hood with screws. Simply remove the screws and

make sure the sash cables or chains are on the pulleys or sprockets before

operation of the sash.

NOTE: THE SASH WEIGHT ITSELF WAS INDIVIDUALLY

MATCHED FOR THIS SPECIFIC HOOD AND SHOULD NOT

BE EXCHANGED ON ANY OTHER UNIT.

Installing the Hood on a Supporting

Structure and Work Surface

The Protector Hood is heavy! Use caution when lifting or

moving the unit.

Le Protecteur Hood est lourd! Soyez prudent lorsque vous

soulever ou déplacer l'appareil.

When installing the Protector Filtered Hood onto a chemically-resistant work surface

or benchtop, ensure that the structure can safely support the combined weight of the

fume hood and any related equipment. The work surface should be at least as wide

as the hood to properly support it. The work surface is aligned flush with the back

of the filtered fume hood for good airflow: this will provide the correct spacing

under the air foil for proper bypass airflow. The lower base cabinets are placed

flush with the front of the work surface as shown in Figure 3-1.

WARNING: It is important to support the rear of the work

surface and filtered fume hood. The cross support provides

support for the bottom of the work surface. Install the cross

support after the base cabinets and work surface are leveled

and before installing the hood.

AVERTISSEMENT : Il est important de soutenir l'arrière de

la surface de travail et filtré hotte. Le support tranversal

soutient le bas de la surface de travail. Installer le support

transversal après que les meubles et la surface de travail soient

nivelés et avant d'installer la hotte.

!



Chapter 3: Getting Started

Product Service 1-800-522-7658

12

Original instructions

The following are instructions for mounting a cross support:

1. Level the base cabinets and the work surface. Work surface should be

placed flush with the back of the filtered fume hood as shown in

Figure 3-1.

2. Scribe a line on the wall or back of the base cabinet to locate the

support under the work surface.

3. Mount the support by attaching it to the wall or base cabinet.

4. Place the hood on top of the work surface and cross support.

The work surface should be smooth and durable, such as a chemically-resistant

epoxy resin. The surface should be nonporous and resistant to the acids, solvents,

and chemicals used in conjunction with the Protector Filtered Fume Hood. The

work surface should also contain a dished recessed area for containing primary

spills.

Figure 3-1

Chapter 3: Getting Started

Product Service 1-800-522-7658

13

Original instructions

Connecting the Electrical Supply Source

to the Protector Hood

Prior to connecting any electrical wiring to the fume hood structure, refer to the

hood identification plate for the proper electrical requirements of your specific

model.

WARNING: The building electrical supply system for

Protector Hoods should include overload protection. A switch

or circuit breaker should be in close proximity to the

equipment and within easy reach of the operator. The switch

or circuit breaker is to be marked as the disconnecting device

for the equipment. Consult the current version of NFPA 70

®

,

NEC

®

for proper installation.

AVERTISSEMENT : Le système d’alimentation électrique de la

Hotte Protecteur doit inclure la protection contre la surcharge. Un

commutateur ou disjoncteur doit être tout près de l'équipement et

à portée facile de l'opérateur. Le commutateur ou le disjoncteur

doit être marqué comme l'appareil débranchant pour

l'équipement. Consultez la version actuelle de la norme NFPA 70

®

,

NEC

®

pour une installation correcte.

The identification plate, model number, serial number, and electrical connection

boxes are accessible from the front of the fume hood by removing the front panel.

The Protector Hood is normally wired for 115 Volt, 50/60 Hz, 20 Amp or 230Volt,

50/60 Hz, 10 Amp electrical service. Check the I.D. plate behind the front panel

for voltage verification. The number of circuits varies depending on the model.

All of the electrical connections for the individual duplexes are terminated at the

single point internal junction box for hook-up by a qualified electrician. If needed,

the individual duplexes can be converted for instant attachment to a wall outlet by

a qualified electrician by ordering 115V harness 9582700 or 230V harness

9582701. The main power to the control panel, fans, and lights uses less than 3

amps and a main power cord is included for instant attachment to a wall outlet.

The single point internal junction box is used for the connection of the duplex

outlets. Refer to the wiring diagram for your Protector Hood in Appendix C:

Protector Filtered Hood Specifications.

The fume hood is required to be grounded to the MAINS protective earthing ground

for safe operation. Using a ring terminal sized for a 10-24 machine screw, connect

the MAINS ground conductor to the grounding lug marked with the protective

earthing symbol, . Only MAINS ground conductors should be connected to the

protective earthing ground lug, no other conductors should be connected to this

grounding lug. Using wire nuts, connect the MAINS supply conductors to the fume

hood supply wires. Ensure that the wires are connected as per the appropriate wire

color codes for the input voltage. For 115V Phase (Hot) is black and Neutral is

!

Chapter 3: Getting Started

Product Service 1-800-522-7658

14

Original instructions

white, for 230V Phase1 is brown and Phase2 is blue. Refer to the wiring diagram for

your Protector Hood in Appendix C: Protector Filtered Hood Specifications.

Figure 3-2

Internal Junction

Boxes located on top,

one on each side.

Chapter 3: Getting Started

Product Service 1-800-522-7658

15

Original instructions

All wiring for the filtered fume hood SHOULD be performed

by a licensed electrician and conform to all local codes.

Tout le câblage pour la hotte filtrée doit être effectuée par un

électricien agréé et conformément à tous les codes locaux.

The fluorescent light has been mounted inside the light module located on top of

the filtered hood. To change the fluorescent light bulbs in your filtered hood, you

must first remove the front panel from the hood. Next remove the filters, pre-

filters, and fan modules. Lift fixture up and replace any deflective bulbs. Reverse

order to reassemble.

Connecting the Service Lines to the

Protector Hood

The filtered hoods with service fixtures have been plumbed from the valve to the

hose connector or gooseneck for your installation convenience. Supply tubing

shall be provided by the qualified installer. Tubing can enter the filtered hood

from above, through the back, or through the work surface to make these

connections to the service fixtures.

NOTE: Inspect all fittings for leakage. Tighten the fittings

slightly if needed.

NOTE : Inspecter toutes les installations à la recherche de

fuite. Resserrer les installations légèrement si nécessaires.

CAUTION: Do not use oxygen with any standard service

fixture. Contact Labconco Customer Service for oxygen

fixture information.

PRUDENCE : Ne pas utiliser de l'oxygène avec l'accessoire de

service standard. Contacter le Service Clientèle de Labconco

pour les informations d'accessoire d'oxygène.

Should access to the filtered hood plumbing fixture bodies be required, remove

the service access plate on the hood front corner posts by loosening their

individual screws (see item 11, Figure A-1 in Appendix A). The valve body will

now be fully exposed for any service work that may be necessary. The service

fixtures supplied on your laboratory hood are designed for use with the following

services:

 Air

 Hot Water

 Vacuum

 Cold Water

 Natural Gas – See caution below

!

La page charge ...

Labconco Protector Airo 184410000 Series Manuel utilisateur

Ce manuel convient également à

Labconco Protector Airo 184410000 Series Manuel utilisateur

dans d''autres langues

Autres documents