DeWalt DWMT70782L Manuel utilisateur

Marque: DeWalt

Modèle: DWMT70782L

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

DWMT70782L

Angle Die Grinder

Meuleuse d’outillage d’angle

Rectiﬁcadora de matrices angular

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT • www.dewalt.com

English

A. Spindle

B. Collet Nut

C. Collet

D. Trigger

E. Safety Throttle Lever

SPECIFICATIONS

MODEL

DWMT70782L

FREE SPEED (@90PSI)

20240 RPM

EXHAUST TYPE

Rear

COLLET DIAMETER

1/4” (6.4MM)

AVERAGE AIR CONSUMPTION AT

LOAD

21 SCFM (9.9 L/s)

3.0 CFM (1.4 L/s)

NET WEIGHT

1.17 LBS (0.5Kg.)

AIR INLET SIZE

1/4” NPT(F)

RECOMMENDED HOSE SIZE

3/8” (10MM)

MAX. AIR PRESSURE

90 PSI

DWMT70782L ANGLE DIE GRINDER

F. ¼” Air Inlet

G. Exhaust

H. Ergonomic Body

I. Speed Control Screw

FIG.1

English

Denitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and pay

attention to these symbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death

or serious injury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in minor

or moderate injury.

CAUTION: Used without the safety alert symbol

indicates a potentially hazardous situation which,

if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY D

WALT TOOL, CALL US TOLL FREE AT:

1-800-4-D

WALT (1-800-433-9258)

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or

other reproductive harm. Some example of these chemicals are:

 • Leadfromlead-basedpaints

 • Crystallinesilicafrombricksandcement

and other masonry products

 • Arsenicandchromiumfromchemically-treatedlumber

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, al ways wear OSHA/MSHA/NIOSH approved,

properly fit ting face mask or res pi ra tor when us ing such tools.

When using air tools, basic safety precautions should always be

followed to reduce the risk of personal injury.

WARNING: This product contains chemicals, known to the

State of California to cause cancer, and birth defects or other

reproductive harm. Wash hands after handling.

SAVE THESE INSTRUCTIONS

WARNING:

Improper operation or maintenance of this product

could result in serious injury and property damage.

Read and understand all warnings and operating

instructions before using this equipment. When using

air tools, basic safety precautions should always be

followed to reduce the risk of personal injury.

WARNING:

Read and understand this instruction manual and tool labels

before installing, operating or servicing this tool. Keep these

instructions in a safe accessible place.

Operators and others in work area must wear ANSI Z87.1 CAN/

CSA Z94.3 approved safety glasses with side shields.

Operators and others in work area must wear ear protection.

Oil daily for optimal performance.

English

WARNING:

 • Nevertriggerthetoolwhennotappliedtoaworkobject

Attachmentsmustbesecurelyattached.

Looseattachmentscancauseseriousinjury.

 • Protectairlinesfromdamageorpuncture.

 • Neverpointanairtoolatoneselforanyotherperson.

Serious injury could occur.

 • Checkairhosesforweakorwornconditionbeforeeachuse.

Make sure all connections are secure.

 • Keepallnuts,boltsandscrewstightandensureequipmentisin

safe working condition.

 • Donotputhandsnearorundermovingparts.

WARNING:

 • Avoidprolongeduse:repetitivemotionorexposuretovibration

may be harmful to your hands or arms. Use gloves to provide

extra cushion, take frequent rest periods, and limit daily

time of use.

 • DoNotUseoxygenorreactivegases;explosionmayoccur.

 • DoNotExceedairpressureof90PSI.

 • Readallmanualsincludedwiththisproductcarefully.

Be thoroughly familiar with the controls and the proper use

of the equipment.

 • Onlypersonswellacquaintedwiththeserulesofsafeoperation

should be allowed to use the air tool.

 • Donotexceedanypressureratingofanycomponent

in the system.

 • Disconnecttheairtoolfromairsupplybeforechangingtoolsor

attachmentsandduringnon-operation.

 • Alwayswearsafetyglassesandearprotectionduringoperation.

Alwayswearapprovedsafetyglasseswithshields.Alwayswear

approved hearing protection.

 • Donotwearloosefittingclothingorapparelwhichcontains

loose straps or ties, etc. Which could become entangled in

moving parts of the tool and results in serious personal injury.

 • Donotwearjewelry,watches,identifications,bracelets,

necklace, etc. When operating any tool, they may become

caught in moving parts and result in serious injury.

 • Donotdepresstriggerwhenconnectingtheairsupplyhose.

 • Alwaysuseattachmentsdesignedforusewithair

powered tools.

 • Donotusedamagedorwornattachments.

English

WARNING: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Abrasivetoolssuchas

sanders and grinders,

rotating tools such as drills,

and impact tools such as

wrenches, hammers,

and reciprocating saws

are capable of generating

sparks which could

result in ignition of

flammable materials.

 • Neveroperatetoolsnear

flammable substances such

as gasoline, naptha,

cleaning solvents, etc.

 • Workinaclean,well

ventilated area free of

combustible materials.

 • Neveruseoxygen,

carbon dioxide or other

bottled gases as a power

source for air tools.

 • Exceedingthemaximum

pressure rating of tools

accessories could cause

an explosion resulting

in serious injury.

 • Usecompressedairregulated

to a maximum pressure at or

below the rated pressure

of any attachments.

WARNING: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• Abrasivetools,suchas

grinders, sanders, and

cut-off tools generate dust

and abrasive materials which

can be harmful to human

lungs and respiratory system.

• AlwayswearMSHA/NIOSH

approved, properly fitting face

mask or respirator when

using such tools.

• Somematerialssuchas

adhesives and tar contain

chemicals whose vapors

could cause serious injury

with prolonged exposure.

• Alwaysworkinaclean,dry,

well ventilated area.

CAUTION: RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Longtermexposuretonoise

produced from the operation

of air tools can lead to

permanent hearing loss.

 • AlwayswearANSI (S3.19)

hearing protection.

English

WARNING:

RISK OF INJURY

WHAT CAN HAPPEN HOW TO PREVENT IT

• Toolsleftunattended,orwith

the air hose attached can be

activated by unauthorized

persons leading to their injury

or injury to others.

•Removeairhosewhentool

is not in use and store tool

in a secure location away

from reach of children and/or

untrained users.

• Airtoolscanpropelloose

objects or other materials

throughout the work area.

• Useonlyparts,and

accessories recommended by

the manufacturer.

• Keepworkareacleanandfree

of clutter. Keep children and

others away from work area

during operation of the tool.

• Keepworkareawelllit.

• Airtoolscanbecome

activated by accident during

maintenance or tool changes.

• Removeairhosetolubricate

or add grinding attachments,

sanding discs, etc.,

to the tool.

• Nevercarrythetool

by the hose.

• Avoidunintentionalstarting.

Don’t carry hooked-up tool with

finger on trigger.

• Repairserviceshouldbedone

only by an authorized service

representative.

• Awrenchorakeythatisleft

attached to a rotating part of

the tool increases the risk of

personal injury.

• Removeadjustingkeysand

wrench before turning

the tool on.

WHAT CAN HAPPEN HOW TO PREVENT IT

• Using inflator nozzles for

duster applications can cause

serious injury.

• DO NOT use inflator nozzles

for duster applications.

• Air tools can cause the work

piece to move upon contact

leading to injury.

• Use clamps or other devices

to prevent movement.

• Lossofcontrolofthetoolcan

lead to injury to self or others

• Never operate tool while

under the influence of

drugs or alcohol.

• Don’t overreach. Keep proper

footing and balance at all times.

• Keep handles dry, clean, and

free from oil and grease.

• Stay alert. Watch what you are

doing. Use common sense.

Do not operate tool when

you are tired.

• Poor quality, improper, or

damaged tools such as

grinding wheels, chisels,

sockets, drill, etc., can fly

apart during operation,

propelling particles

throughout the work area

causing serious injury.

• Always use tool attachments

rated for the speed of

the power tool.

• Never use tools which have

been dropped, impacted or

damaged by use.

• Do not apply excessive force

to the tool – let the tool

perform the work.

English

WARNING:

RISK OF INJURY (CONTINUED)

WHAT CAN HAPPEN HOW TO PREVENT IT

• Improperlymaintainedtool

and accessories can

cause serious injury.

• Maintainthetoolwithcare.

• Thereisariskofburstingif

the tool is damaged.

• Checkformisalignmentor

binding of moving parts,

breakage of parts, and any

other condition that affects the

tool’s operation. If damaged,

have the tool serviced

before using.

WARNING:

RISK OF ELETRIC SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Thistoolisnotprovidedwith

an insulated gripping surface.

Contact with a “live” wire will

also make exposed metal

parts of the tool “live”

and can result in

electrocution or death.

• Avoidbodycontactwith

grounded surfaces such as

pipes, radiators, ranges, and

refrigerators. There is an

increased risk of electric shock

if your body is grounded.

• Thoroughlyinvestigatethe

workpiece for possible hidden

wring before performing work.

English

WARNING:

RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Airpoweredequipmentand

power tools are capable of

propelling materials such as

metal chips, saw dust, and

other debris at high speed,

which could result in

serious eye injury.

• AlwayswearANSI Z87.1 CAN/

CSA Z94.3 approved safety

glasses with side shields.

• Neverleaveoperatingtool

unattended. Disconnect air

hose when tool is not in use.

• Compressedaircanbe

hazardous. The air stream

can cause injury to soft tissue

areas such as eyes, ears, etc.

Particles or objects

propelled by the stream

can cause injury.

• Foradditionalprotectionuse

an approved face shield in

addition to safety glasses.

• Toolattachmentscanbe

come loose or break and fly

apart propelling particles at

the operator and others

in the work area.

• Makesurethatany

attachments are

securely assembled.

WARNING:

RISK OF CUT OR BURNS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Toolswhichcut,shear,

drill, punch, chisel, etc.,

are capable of causing

serious injury.

 • Keeptheworkingpart

of the tool away from

hands and body.

WARNING:

RISK OF ENTANGLEMENT

WHAT CAN HAPPEN HOW TO PREVENT IT

• Toolswhichcontainmoving

elements, or drive other

moving tools such as grinding

wheels, sockets, sanding

discs,etc., can become

entangled in hair, clothing,

jewelry and other loose

objects, resulting

in severe injury.

• Neverwearloosefitting

clothes, or apparel which

contains loose straps or ties,

etc., which could become

entangled in moving parts

of the tool.

• Removeanyjewelry,watches,

identifications, bracelets,

necklaces, etc., which might

become caught by the tool.

• Keephandsawayfrommoving

parts. Tie up or cover long hair.

• Alwayswearproperfitting

clothing and other safety

equipment when

using this tool.

English

WARNING:

AIR SUPPLY AND CONNECTIONS

• Donotuseoxygen,combustiblegases,orbottledgases

as a power source for this tool as the tool may explode,

possibly causing injury.

• Donotusesupplysourceswhichcanpotentiallyexceed

200PSI(13.8bar)astoolmayburst,possiblycausinginjury.

• Theconnectoronthetoolmustnotholdpressure

when air supply is disconnected. If a wrong fitting is used,

the tool can remain charged with air after disconnecting

and thus will be able to after the air line is disconnected

possibly causing injury.

• Alwaysdisconnectairsupply:

1)Beforemakingadjustments;

2)Whenservicingthetool;

3)Whentoolisnotinuse;

4)Whenmovingtoadifferentworkarea,asaccidental

actuation may occur, possibly causing injury.

WARNING:

ADDITIONAL SAFETY INSTRUCTIONS FOR

GRINDERS

 • Accessoriesmustberatedforatleastthespeed

recommended on the tool. Wheels and other accessories

running over rated speed can fly apart and cause Injury.

Accessoryratingsmustbeabovelistedminimumwheel

speed for tool.

 • Donotusesawbladesorothertoothedbladeswiththistool.

Serious injury may result.

 • Whenstartingtoolwithneworreplacementwheelor

otheraccessory,holdtoolinwell-protectedareaand

run for one minute.

 • Neverstartthetoolwithanoperatororothersinlinewith

the wheel or accessory. If the wheel or accessory has

an undetected flaw, it can burst in less than a minute.

 • Avoidbouncingthewheelorsubjectingittoroughhandling

 • Directsparksawayfromoperator,bystandardsor

flammable materials.

 • Disconnecttoolfromairsupplywhenchangingaccessories

or when not in use.

 • Donotcarrytoolwiththrottledepressed.DonotdisableThrottle

SafetyLever.Donottapeorlockthrottleinrunposition.

 • Useonlyrecommendedairtoolgrinderaccessories.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

English

FEATURES

COLLET

The

collet (C)

allows you to

securely hold the mandrel of an

insert tool. The

collet nut (B)

and

spindle (A)

are designed with two

flat sides each to allow for easy

insert tool assembly with the sup-

plied wrenches.

TRIGGER

The trigger

(D)

allows the operator

to control the start and stop of

the air tool.

SAFETY THROTTLE LEVER

The safety throttle lever (E)

prevents the tool from accidentally

being actuated.

ERGONOMIC BODY

The body of the air tool is made of

aluminum for reduced weight and

superior power-to-weight ratio. This

air tool has an ergonomic grip (H)

made of molded thermoplastic

elastomer (TPE) designed for

improved comfort slippage

reduction, and better tool control.

AIR INLET

The tool’s air inlet (F) located at

the bottom of the handle is used

for connecting an air supply with a

standard 1/4" NPT American thread

EXHAUST

The exhaust (G) is located at the base of the handle and allows the

exhaust to be directed away from the operator and working area.

SPEED CONTROL SCREW

The speed control screw (I) allows the operator to increase or

decrease the rotary speed of the tool. The speed control screw is

adjustable with a flat screwdriver.

FLAT

English

INSTALLATION

Air Supply

The recommended hook-up is shown in Figure A. Pneumatic tools

operate on a wide range of air pressures. For maximum efficiency

and longer tool life, the pressure of the air supplied to these

tools MUST not exceed the rated PSI at the tool when the tool is

running. Using a higher than rated pressure will cause faster wear

and drastically shorten the tool’s life. A higher air pressure can also

cause an unsafe condition and explosion.

The inside diameter of the hose should be increased to

compensate for unusually long air hoses (over 25 feet).

Minimum hose diameter should be 3/8" I.D. and fittings should

have 1/4” NPT thread.

The use of air line lubricators and air line

filters is recommended to prevent water

in the line that can damage the tool. Drain

the air tank daily. Clean the air inlet filter

screen on at least a weekly schedule to

remove accumulated dirt or other matter

that can restrict air flow.

The tool’s air inlet used for connecting

an air supply has standard 1/4” NPT

American thread.

Safety Rules For Pneumatic Tools

1) Inspect the air hose for cracks or other problems.

Replace the hose if worn.

2) Never point an air hose at another person.

3) Disconnect the tool when not in use, or before performing

service or changing accessories.

4) Use proper hoses and fittings. Never use quick change

couplings attached to the tool. Instead, add a hose and

coupling between the tool and the air supply.

1/2”(or larger)

Pipe and Fittings

Coupler

Air Hose

Leader Hose

Tool

Nipple

Oiler

Filter

Drain Daily

Figure A

English

PREPARATION FOR USE

Proper Use Of The Tool

Your new Angle Die Grinder is designed for grinding and

deburring operations in confined areas. This tool features

a rear exhaust to direct airflow away from the work area,

a built-in regulator for convenient speed control and a lock-off

lever to prevent accidental starts.

Work Stations

Your Angle Die Grinder should only be used as a hand operated

tool. It is always recommended that the tool is used when standing

with solid footing. It can be used in other positions but before any

such use, the operator must be in a secure position having a firm

grip and footing.

Putting Into Service

Air Supply

CAUTION:

This air tool requires lubrication BEFORE initial use,

also before and after each additional use.

WARNING:

Use a clean lubricated air supply that will give a

measuredairpressureatthetoolof90psi/6.2barwhenthetool

is running with the trigger fully depressed.

Use recommended hose size. It is recommended that the tool is

connected to the air supply as shown in figure A on page 11.

Do not connect the tool to the air line system without incorporat-

ing an easy to reach and operate air shut off valve. The air supply

should be lubricated. It is strongly recommended that an air filter,

regulator, lubricator (FRL) is used as shown in figure A on page

11 as this will supply clean, lubricated air at the correct pressure to

the tool. Details of such equipment can be obtained from your

supplier. If such equipment is not used then the tool should be

lubricated by shutting off the air supply to the tool and then

depressurizing the line by pressing the trigger on the tool.

Disconnect the air line and pour into the air inlet 1 teaspoon (5cc.) of

a suitable pneumatic motor lubricating oil, preferably

incorporating a rust inhibitor. Reconnect tool to air supply and run

tool slowly for a few seconds to allow air to circulate the oil.

Lubricate tool daily if used frequently, or when it starts to slow or

lose power.

Using An Angle Die Grinder

WARNING:

1) Read all instructions before using this tool. All operators must

be fully trained in its use and aware of these safety rules.

2) Do not exceed the maximum working air pressure of

90 psi/6.2 bar.

3) Use personal safety equipment.

4) Use only compressed air at the recommended conditions.

5) If the tool appears to malfunction, remove from use

immediately and arrange for service and repair.

6) If the tool is used with a balancer or other support device,

ensure that it is fixed securely.

7) Always keep hands away from the working attachment fitted to

the tool.

8) The tool is not electrically insulated. Never use the tool if there

is any chance of it coming into contact with live electricity.

9) When using the tool, always adopt a firm footing and/or position

and grip the tool firmly to counteract any forces or

reaction forces that may be generated while using the tool.

10) Use only genuine Dewalt spare parts or parts which perform

equivalently. Do not make temporary or permanent repairs with

unauthorized parts.

11) Do not lock, tape, wire, etc., the on/off trigger in the run

position. The trigger must always be free to return to

the “off” position when it is released.

English

Using An Angle Die Grinder Continued

12) Always shut off the air supply to the tool and depress the

trigger to release air from the feed hose before fitting,

adjusting or removing the working attachment.

13) Check hoses and fittings regularly for wear. Replace if

necessary. Do not carry the tool by its hose. Ensure the

hand is removed from the on/off trigger when carrying

the tool with the air supply connected.

14) Take care against entanglement of moving tool parts

with clothing, ties, hair, cleaning rags, etc. This will

cause the body to be drawn towards the tool and can

be very dangerous.

15) Safe working practices and observe all relevant legal

requirements when installing, using or maintaining the tool.

16) Only install the tool when an easily accessible and easily

operable on/off switch is incorporated in the air supply.

17) Take care that the tool exhaust air does not

cause problems or blow onto another person.

18) Never lay a tool down unless the working attachment has

stopped moving.

PRE-START CHECKLIST (FIG. 1, PG. 2)

•Drainwaterfromaircompressortankandcondensationfrom

air lines. (Please refer to air compressor’s operation manual.)

•Lubricatethetool.(Pleaserefertothe“Maintenance”section

in the manual.)

•Selecttherequiredattachment.Themandreloftheattachment

must match the size of the collet on the air grinder.

WARNING: Risk of unsafe operation. Firmly grasp air hose

with hand when installing or disconnenting to prevent hose whip.

WARNING: Risk of bursting. Too much air pressure causes

a hazardous risk of bursting. Check the manufacturer’s maximum

pressure rating for air tools and accessories. The regulator output

pressure must never exceed the maximum pressure rating.

INSERT TOOL ASSEMBLY (FIG. 1, PG. 2)

•Loosenthecollet (C) on the air die grinder by holding the

spindle (A) with the supplied 11mm wrench while loosening

the collet nut (B) with the supplied 17mm wrench.

•Insertmandrelofaninserttoolintothecollet (C) and tighten

by fastening the collet nut (B) with the 17mm wrench.

NOTE: Always check the weariness of the insert tool in order to

increase the efficiency and safety of the air grinder.

IMPORTANT: Before using this tool, ensure that the insert tool is

fixed in the collet very tightly.

FASTEN

LOOSEN

FASTEN

LOOSEN

11MM WRENCH

17MM WRENCH

English

OPERATING PROCEDURES

Start-up (Fig. 1, pg. 2)

•

Connect the tool to air source with the hose of recommended size.

•Turnontheaircompressorandallowtheairtanktobefilled.

•Settheaircompressorregulatorto90PSI.Thisair

tool operates at a maximum of 90 PSI air pressure.

•Pushthesafety lever forward (1) while depressing the trigger (2)

to start operating the tool.

Shut-down (Fig. 1, pg. 2)

•Releasethetriggerinordertostopthetool.

•Fix/takeawaytheinserttool.

•Whenjobiscompleted,turnofftheaircompressorandstore

the air tool after lubrication. For safety, put the tool on a hanger

or on a soft flat pad when not in use.

•Whenchanginggrindingattachmentsandaccessories,

always disconnect the air supply to avoid injury.

OPERATING INSTRUCTIONS

•To begin operation, grip tool and depress safety throttle

lever while engaging the trigger.

 •Tomountstonesandotheraccessories,usethe

wrenches supplied with the tool. Always disconnect air

supply before changing any accessories.

 • Thegrindershouldbegraduallyappliedtotheworksurface

until the stone or burr becomes worn. Always replace

excessively worn stones or burrs.

 • Makesmoothcontactwiththeworkandavoidany

bumping action or excessive force.

English

MAINTENANCE

Lubrication

Air tools require lubrication throughout the lifetime of the tools.

The air motor and bearing uses compressed air to power the tool.

The compressed air contains moisture that will rust the air motor

and other parts in side of the tools, therefore lubrication is required

daily. Failure to lubricate the air tool properly will dramatically

shorten the life of the tool and will void the warranty

CAUTION: This air tool requires lubrication BEFORE initial use,

also before and after each additional use.

To Lubricate The Air Tool Manually:

1. Remove any attachment on the air tool.

2. Disconnect the tool from the air supply source, place

the air inlet face up.

3. Depress the trigger and place about 1 teaspoon

(5cc.) of air tool oil into the air inlet. (Depressing the trigger

will help circulate oil in the motor.)

NOTE: Use SAE #10 weight oil if air tool oil is not available.

4. Connect the tool to an air source, cover the exhaust end

with a towel and run for about 20 to 30 seconds.

WARNING: Keep out of the reach of children. If taken internally,

do not induce vomiting, call a doctor immediately.

WARNING: Anyexcessoilinthemotorisimmediatelyexpelled

fromtheexhaustport.Alwaysdirectexhaustportawayfrompeople

or objects.

Storage:

The air tool must be lubricated before storing.

Follow the “Lubrication” instruction with exception of step 4.

SERVICE INFORMATION

Please have the following information available for all service calls:

Model Number _________________________________________

Date and Place of Purchase ______________________________

FULL THREE YEARS WARRANTY

DeWALT heavy duty industrial tools are warranted for 3 years from

date of purchase. We will repair, without charge, any defects due

to faulty materials or workmanship. For warranty repair information,

call 1-800-4-D

WALT. This warranty does not apply to accessories

or damage caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and you may

have other rights which vary in certain states or provinces.

Latin America: This warranty does not apply to products sold in

Latin America. For products sold in Latin America, see country

specific warranty information contained either in the packaging, call

the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

WALT

for a free replacement.

English

LAS CAÍDAS PUEDEN CAUSAR

LESIONES GRAVES. NO PISAR NI

PARARSE EN ESTA ÁREA.

ADVERTENCIA

LES CHUTES PEUVENT CAUSER DE GRAVES

BLESSURES. NE MARCHEZ PAS ET NE VOUS

TENEZ PAS SUR CET EMPLACEMENT.

AVERTISSEMENT

FALLS CAN CAUSE SERIOUS

INJURIES. DO NOT STEP OR STAND

ON THIS AREA.

WARNING

SEE OWNER’S MANUAL FOR

BREAK-IN PROCEDURES.

CAUTION

PARA EL PROCEDIMIENTO DE

ASENTADO DE LA MAQUINA, VER

MANUAL DEL OPERARIO.

ATENCIÓN

CONSULTEZ LE MANUEL DE

L’UTILISATEUR POUR LES

PROCEDURES DE RODAGE.

ATTENTION

ADVERTENCIA

EL USO INDEBIDO PUEDE GENERAR RIESGOS. SEGUIR ESTAS INSTRUCCIONES: RIESGO DE ESTALLIDO. ASEGÚRESE QUE LA VÁLVULA DE SALIDA DEL

COMPRESOR ESTE REGULADA POR DEBAJO DEL MÁXIMO DE LA PRESIÓN DE OPERACIÓN DE LA PISTOLA ROCIADORA O HERRAMIENTA. ANTES DE ARRANCAR

EL COMPRESOR, TIRAR DEL ANILLO EN LA VÁLBULA DE SEGURIDAD PARA ASEGURARSE QUE LA VÁLVULA SE MUEVE LIBREMENTE. DRENAR EL AGUA DEL TANQUE DESPUÉS DE CADA USO.

RIESGO DE FUEGO O EXPLOSIÓN. NO ROCIAR LÍQUIDO NI PINTURAS INFLAMABLES O COMBUSTIBLES CERCA DE CHISPAS, LLAMAS, LLAMAS DE PILOTO O EN ÁREAS CERRADAS. EL ÂREA DE

TRABAJO DEBE ESTAR BIEN VENTILADA. MANTENER EL COMPRESOR ALEJADO POR LO MENOS 20 PIES DEL AREA DE PINTURA. NO LLEVAR NI OPERAR EL COMPRESOR NI DISPOSITIVO ELÉCTRICO

ALGUNO CERCA DEL AREA DEL ROCIADO. NUNCA FUME EN EL ÁREA DEL ROCIADO. USAR UNA MANGUERE DE UN MÍNIMO DE 25 PIES PARA CONECTAR LA PISTOLA AL COMPRESOR. RIESGO DE

DAÑOS PERSONALES. USAR GAFAS DE SEGURIDAD ANSI Z87. NUNCA APUNTAR EL CHORRO DE AIRE COMPRIMIDO O DE MATERIAL QUE SE ESTÉ ROCIANDO A SÍ MISMO NI A OTRAS PERSONAS.

NE RESPIRAR EL AIRE COMPRIMIDO. REDUCIR LA PRESIÓN A CERO ANTES DE DESMONTAR LA MANGUERA. RIESGO DE CHOQUE ELÉCTRICO. ALTO VOLTAJE. DESCONECTAR LA UNIDAD ANTES DE

QUITAR LA CUBIERTA. NO EXPONER A LLUVIA. ALMACENAR EN INTERIORES. PARA SEGURIDAD COMPLETA, OPERACIÓN E INSTRUCCIONES PARA REPARAR, LEER EL MANUAL DEL OPERADOR.

AVERTISSEMENT

UNE UTILISATION INCORRECTE PEUT ÊTRE DANGEREUSE. SUIVEZ LES INSTRUCTIONS CI-DESSOUS: RISQUE D'ECLATEMENT. ASSUREZ-VOUS QUE LA

PRESSION DE SORTIE DU COMPRESSEUR EST RÉGLÉE À UN NIVEAU INFÉRIEUR À LA PRESSION D'UTILISATION MAXIMUM DU PISTOLET VAPORISATEUR OU DE

L'ACCESSOIRE. AVANT DE DÉMARRER LE COMPRESSEUR, TIREZ SUR L'ANNEAU DE LA SOUPAPE DE SÛRETÉ POUR VOUS ASSURER QU'ELLE FONCTIONNE LIBREMENT. VIDANGEZ L'EAU DU RÉSERVOIR

À AIR APRÈS CHAQUE UTILISATION. RISQUE D'INCENDIE OU D'EXPLOSION. NE PAS VAPORISER UN LIQUIDE OU UN PEINTURE INFLAMMABLE OU COMBUSTIBLE PRÈS D'ÉTINCELLES, DE FLAMMES, DE

VEILLEUSES NI DANS UN ENDROIT RESTREINT OU RENFERMÉ. L'AIRE DE VAPORISATION DOIT ÊTRE BIEN AÉRÉE. GARDEZ LE COMPRESSEUR À UNE DISTANCE D'AU MOINS 20 PIEDS DE LA SURFACE À

VAPORISER. NE PORTEZ PAS LE COMPRESSEUR ET NE L'UTILISEZ PAS NI AUCUN AUTRE APPAREIL ÉLECTRIQUE À PROXIMITÉ DE L'AIRE DE VAPORISATION. NE FUMEZ JAMAIS QUAND VOUS

VAPORISEZ. UTILISEZ UN FLEXIBLE D'AIR D'UNE LONGUEUR MINIMUM DE 25 PIEDS POUR RELIER LE PISTOLET VAPORISATEUR AU COMPRESSEUR. RISQUE DE BLESSURES CORPORELLES. PORTEZ DES

LUNETTES DE PROTECTION ANSI Z87. NE DIRIGEZ JAMAIS L'AIR COMPRIME OU DES MATÉRIAUX VERS SOI OU VERS AUTRUI. NE JAMAIS UTILISER DE L'AIR COMPRIMÉ POUR LA RESPIRATION. RÉGLEZ

LA PRESSION À ZÉRO AVANT DE RETIRER LE BOYAU. RISQUE DE CHOC ÉLECTRIQUE. VOLTAGE DANGEREUX. DEBRANCHEZ LA MACHINE AVANT D'ENLEVER BOITIER. N'EXPOSEZ PAS LE COMPRESSEUR

À LA PLUIE. REMISEZ-LE À L'INTÉRIEUR. LISEZ LE MANUEL DE L'UTILISATEUR POUR DES INSTRUCTIONS COMPLÈTES CONCERNANT LA SÉCURITÉ, L'UTILISATION ET LES RÉPARATIONS.

INCORRECT USE CAN CAUSE HAZARDS. FOLLOW THESE INSTRUCTIONS: RISK OF BURSTING. MAKE SURE THE COMPRESSOR OUTLET PRESSURE IS SET

LOWER THAN THE MAXIMUM OPERATING PRESSURE OF THE SPRAY GUN OR TOOL. BEFORE STARTING THE COMPRESSOR, PULL THE RING ON THE SAFETY

VALVE TO MAKE SURE THE VALVE MOVES FREELY. DRAIN WATER FROM TANK AFTER EACH USE. RISK OF FIRE OR EXPLOSION. DO NOT SPRAY A FLAMMABLE OR COMBUSTIBLE

LIQUID OR PAINT NEAR SPARKS, FLAMES, PILOT LIGHTS, OR IN A CONFINED AREA. THE SPRAY AREA MUST BE WELL VENTILATED. KEEP COMPRESSOR AT LEAST 20 FEET AWAY FROM

SPRAY AREA. DO NOT CARRY AND OPERATE THE COMPRESSOR, OR ANY OTHER ELECTRICAL DEVICE NEAR THE SPRAY AREA. NEVER SMOKE WHEN SPRAYING. USE A MINIMUM OF

25 FEET OF HOSE TO CONNECT A SPRAY GUN TO THE COMPRESSOR. RISK OF PERSONAL INJURY. WEAR ANSI Z87 SAFETY GLASSES. NEVER SPRAY COMPRESSED AIR OR MATERIAL

AT SELF OR OTHERS. DO NOT USE COMPRESSED AIR FOR BREATHING. REGULATE PRESSURE TO ZERO BEFORE REMOVING HOSE. RISK OF ELECTRICAL SHOCK. HAZARDOUS VOLTAGE.

UNPLUG UNIT BEFORE REMOVING COVER. DO NOT EXPOSE TO RAIN, STORE INDOORS. READ OWNER'S MANUAL FOR COMPLETE SAFETY, OPERATION, AND REPAIR INSTRUCTIONS.

WARNING

HOLD HOSE FIRMLY TO

PREVENT HOSE WHIP.

CAUTION

SOSTENGA LA MANGUERA

CON FIRMEZA PARA EVITAR EL.

ATENCIÓN

BIEN TENIR LE TUYAU POUR

ÉVITER UN À-COUP.

ATTENTION

DRAIN TANK DAILY OR AFTER EACH USE. CONDENSATION BUILD-UP MAY CAUSE CORROSION