Sony CDX-GT410U Le manuel du propriétaire

Operating Instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

CDX-GT414U

CDX-GT410U

2-890-967-31 (1)

GB

DE

FR

IT

NL

To cancel the demonstration (DEMO) display, see page 12.

Zum Deaktivieren der Demo-Anzeige (DEMO) schlagen Sie bitte auf Seite 14 nach.

Pour annuler la démonstration (DEMO), reportez-vous à la page 13.

Per annullare la dimostrazione (DEMO), vedere pagina 14.

Om de demonstratie (DEMO) te annuleren, zie pagina 14.

©

2006 Sony Corporation

FM

/

MW

/

LW

Compact Disc Player

2

“ATRAC”, “ATRAC AD”, SonicStage and their

logos are trademarks of Sony Corporation.

“WALKMAN” and “WALKMAN” logo are

registered trademarks of Sony Corporation.

Warning if your car’s ignition has no

ACC position

Be sure to set the Auto Off function (page 12).

The unit will shut off completely and

automatically in the set time after the unit is

turned off, which prevents battery drain.

If you do not set the Auto Off function, press

and hold (OFF) until the display disappears

each time you turn the ignition off.

For installation and connections, see the

supplied installation/connections manual.

This label is located on the bottom of the

chassis.

Disposal of Old Electrical &

Electronic Equipment (Applicable in

the European Union and other

European countries with separate

collection systems)

This symbol on the product or on its

packaging indicates that this product shall not be treated

as household waste. Instead it shall be handed over to the

applicable collection point for the recycling of electrical

and electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent potential

negative consequences for the environment and human

health, which could otherwise be caused by inappropriate

waste handling of this product. The recycling of materials

will help to conserve natural resources. For more detailed

information about recycling of this product, please contact

your local Civic Office, your household waste disposal

service or the shop where you purchased the product.

Applicable accessory: Remote commander

Microsoft, Windows Media,

and the Windows logo are

trademarks or registered

trademarks of Microsoft

Corporation in the United States and/or other

countries.

3

Table of Contents

Welcome ! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Getting Started

Resetting the unit. . . . . . . . . . . . . . . . . . . . . . . . 4

Preparing the card remote commander . . . . . . . 4

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . 5

Detaching the front panel . . . . . . . . . . . . . . . . . 5

Attaching the front panel . . . . . . . . . . . . . . . 5

Location of controls and basic

operations

Main unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Card remote commander RM-X151 . . . . . . . 6

CD

Display items . . . . . . . . . . . . . . . . . . . . . . . . 8

Repeat and shuffle play. . . . . . . . . . . . . . . . . 8

Radio

Storing and receiving stations . . . . . . . . . . . . . . 8

Storing automatically — BTM . . . . . . . . . . . 8

Storing manually. . . . . . . . . . . . . . . . . . . . . . 8

Receiving the stored stations . . . . . . . . . . . . 8

Tuning automatically . . . . . . . . . . . . . . . . . . 8

RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Setting AF and TA . . . . . . . . . . . . . . . . . . . . 9

Selecting PTY . . . . . . . . . . . . . . . . . . . . . . . 10

Setting CT. . . . . . . . . . . . . . . . . . . . . . . . . . 10

USB devices

Playback USB devices . . . . . . . . . . . . . . . . 10

Display items . . . . . . . . . . . . . . . . . . . . . . . 10

Listening to music on a Mass Storage Class

type audio device . . . . . . . . . . . . . . . . . . . . 11

Listening to music on “Walkman” (ATRAC

Audio Device). . . . . . . . . . . . . . . . . . . . . . . 11

Other functions

Changing the sound settings . . . . . . . . . . . . . . 11

Adjusting the sound characteristics

— BAL/FAD/SUB. . . . . . . . . . . . . . . . . . . 11

Customizing the equalizer curve

— EQ3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Adjusting setup items — SET . . . . . . . . . . . . 12

Using optional equipment. . . . . . . . . . . . . . . . 12

Auxiliary audio equipment. . . . . . . . . . . . . 12

CD/MD changer. . . . . . . . . . . . . . . . . . . . . 13

Additional Information

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Notes on discs . . . . . . . . . . . . . . . . . . . . . . 14

About USB devices . . . . . . . . . . . . . . . . . . 15

Playback order of MP3/WMA/

AAC files . . . . . . . . . . . . . . . . . . . . . . . . . . 15

About MP3 files . . . . . . . . . . . . . . . . . . . . . 15

About WMA files. . . . . . . . . . . . . . . . . . . . 15

About AAC files . . . . . . . . . . . . . . . . . . . . 15

About ATRAC files . . . . . . . . . . . . . . . . . . 15

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Removing the unit. . . . . . . . . . . . . . . . . . . . . . 16

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 17

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 18

Error displays/Messages. . . . . . . . . . . . . . . 19

4

Welcome !

Thank you for purchasing this Sony Compact

Disc Player. You can enjoy your drive with the

following functions.

• CD playback

You can play CD-DA (also containing CD

TEXT*), CD-R/CD-RW (MP3/WMA/AAC

files also containing Multi Session (

page 14))

and ATRAC CD (ATRAC3 and ATRAC3plus

format (

page 15)).

• Radio reception

– You can store up to 6 stations per band (FM1,

FM2, FM3, MW and LW).

– BTM (Best Tuning Memory): The unit selects

strong signal stations and stores them.

• RDS services

– You can use FM station with Radio Data

System (RDS).

• Sound adjustment

– EQ3 stage2: You can choose any one of 7

preset equalizer curves.

• Optional unit operation

Various kinds of audio devices can be

connected, and operated from the unit.

– USB device: A Mass Storage Class USB

device or “Walkman” (ATRAC Audio

Device) can be connected to the front USB

terminal. For details on a usable devices,

please refer to About USB devices (

page 15)

or the Sony support website (page 20).

– Portable audio device: An AUX input

jack on the front of the unit allows connection

of a portable audio device (analog

connection).

– CD/MD changers: CD/MD changers can be

connected to the SONY BUS at the rear of the

unit.

* A CD TEXT disc is a CD-DA that includes

information such as disc, artist and track name.

Getting Started

Resetting the unit

Before operating the unit for the first time, or

after replacing the car battery or changing the

connections, you must reset the unit.

Detach the front panel and press the RESET

button with a pointed object, such as a ball-point

pen.

Note

Pressing the RESET button will erase the clock setting

and some stored contents.

Preparing the card remote

commander

Before using the card remote commander for the

first time, remove the insulation film.

Type of discs Label on the disc

CD-DA

MP3

WMA

AAC

ATRAC CD

RESET

button

5

Setting the clock

The clock uses a 24-hour digital indication.

1 Press and hold the select button.

The setup display appears.

2 Press the select button repeatedly

until “CLOCK-ADJ” appears.

3 Press (SEEK) +.

The hour indication flashes.

4 Rotate the volume control dial to set

the hour and minute.

To move the digital indication, press (SEEK)

–/+.

5 Press the select button.

The setup is complete and the clock starts.

To display the clock, press (DSPL). Press

(DSPL) again to return to the previous display.

With the card remote commander

In step 4, to set the hour and minute, press M or m.

Tip

You can set the clock automatically with the RDS

feature (

page 10).

Detaching the front panel

You can detach the front panel of this unit to

prevent theft.

Caution alarm

If you turn the ignition switch to the OFF

position without detaching the front panel, the

caution alarm will sound for a few seconds.

The alarm will only sound if the built-in

amplifier is used.

1 Press (OFF).

The unit is turned off.

2 Press , then pull it off towards you.

Notes

• Do not drop or put excessive pressure on the front

panel and display window.

• Do not subject the front panel to heat/high

temperature or moisture. Avoid leaving it in a parked

car or on a dashboard/rear tray.

• If the front panel is detached without turning off the

switch during playback by a USB device, data may

be damaged.

Attaching the front panel

Engage part A of the front panel with part B of

the unit, as illustrated, and push the left side into

position until it clicks.

Note

Do not put anything on the inner surface of the front

panel.

B

A

6

Location of controls and basic operations

Main unit

Card remote commander

RM-X151

Refer to the pages listed for details. The

corresponding buttons on the card remote

commander control the same functions as those

on the unit.

A OFF button

To power off; stop the source.

B EQ3 (equalizer) button 11

To select an equalizer type (XPLOD,

VOCAL, EDGE, CRUISE, SPACE,

GRAVITY, CUSTOM or OFF).

C Volume control dial/select button 11

To adjust volume (rotate); select setup items

(press and rotate).

D SOURCE button

To power on; change the source (Radio/CD/

MD*

1

/USB/AUX).

E Disc slot

Insert the disc (label side up), playback

starts.

F Display window

G USB terminal

To connect to the USB device. 10

H Z (eject) button

To eject the disc.

I PTY (Program Type) button 10

To select PTY in RDS.

J (front panel release) button 5

AUX

OFF

DSPL

MODE

PUSH SELECT

SEEK

PAUSE

DIM REP SHUF

EQ3

SOURCE

123456

GP/ALBM

AF

/

TA

PTY

1 2

q

j

q

h

4 5 863

CDX-GT414U

CDX-GT410U

q

a

q

d

q

;

9 q

s

q

f

q

g

7

q

k

OFF

DSPL

SCRL

SEL

SOURCE

MODE

132

465

ATT

VOL

+

–

+

–

4

ws

qd

1

wf

ql

qf

wa

w;

wg

wd

7

K SEEK –/+ buttons

CD/MD*

1

/USB*

2

:

To skip tracks (press); skip tracks

continuously (press, then press again within

about 1 second and hold); reverse/fast-

forward a track (press and hold).

Radio:

To tune in stations automatically (press); find

a station manually (press and hold).

L Receptor for the card remote

commander

M MODE button 8, 13

To select the radio band (FM/MW/LW);

select the unit*

3

; select the play mode*

4

.

N DSPL (display)/DIM (dimmer) button

8, 9

To change display items (press); change the

display brightness (press and hold).

O RESET button (located behind the front

panel)

4

P Number buttons

CD/MD*

1

/USB*

2

:

(1)/(2): GP*

5

/ALBM*

6

–/+

To skip albums (press); skip albums

continuously (press and hold)*

7

.

(3): REP 8

(4): SHUF 8

(6): PAUSE*

8

To pause playback. To cancel, press

again.

Radio:

To receive stored stations (press); store

stations (press and hold).

Q AF (Alternative Frequencies)/TA

(Traffic Announcement) button

9

To set AF and TA in RDS.

R AUX input jack 12

To connect a portable audio device.

The following buttons on the card remote

commander have also different buttons/functions

from the unit. Remove the insulation film before

use (

page 4).

ql < (.)/, (>) buttons

To control CD/radio/MD/USB, the same as

(SEEK) –/+ on the unit.

w; VOL (volume) +/– button

To adjust volume.

wa ATT (attenuate) button

To attenuate the sound. To cancel, press

again.

ws SEL (select) button

The same as the select button on the unit.

wd M (+)/m (–) buttons

To control CD, the same as (1)/(2) (GP/

ALBM –/+) on the unit.

wf SCRL (scroll) button 8

To scroll the display item.

wg Number buttons

To receive stored stations (press); store

stations (press and hold).

*1 When an MD changer is connected.

*2 When a USB device is connected.

*3 When a CD/MD changer is connected.

*4 When an ATRAC Audio Device is connected.

*5 When an ATRAC CD is played.

*6 When an MP3/WMA/AAC is played.

*7 If the changer/USB device is connected, the

operation is different, see page 10, 13.

*8 When playing back on this unit.

Notes

• When ejecting/inserting a disc, keep any USB

devices disconnected to avoid damage to the disc.

• If the unit is turned off and the display disappears, it

cannot be operated with the card remote

commander unless (SOURCE) on the unit is

pressed, or a disc is inserted to activate the unit first.

Tip

For details on how to replace the battery, see

“Replacing the lithium battery of the card remote

commander” on page 16.

About USB cap

When not using the USB terminal (G), use the

supplied USB cap to prevent dust or dirt entering.

Keep the USB cap out of the reach of children to

prevent accidental swallowing.

8

CD

For details on selecting a CD/MD changer, see

page 13.

Display items

A AAC/WMA/ATRAC/MP3 indication

B Source

C Track number/Elapsed playing time, Disc/

artist name, Album/group number*, Album/

group name, Track name, Text information,

Clock

* Album/group number is displayed only when the

album is changed.

To change display items C, press (DSPL);

scroll display items C, press (SCRL) on the

card remote commander or set “A.SCRL-ON”

(

page 12).

Tip

Displayed items will differ, depending on the disc type,

recorded format and settings. For details on MP3/

WMA/AAC, see

page 15; ATRAC CD, see page 15.

Repeat and shuffle play

1 During playback, press (3) (REP) or

(4) (SHUF) repeatedly until the

desired setting appears.

*1 When an MP3/WMA/AAC is played.

*2 When an ATRAC CD is played.

To return to normal play mode, select “ OFF”

or “SHUF OFF.”

Radio

Storing and receiving stations

Caution

When tuning in stations while driving, use Best

Tuning Memory (BTM) to prevent an accident.

Storing automatically — BTM

1 Press (SOURCE) repeatedly until

“TUNER” appears.

To change the band, press (MODE)

repeatedly. You can select from FM1, FM2,

FM3, MW or LW.

2 Press and hold the select button.

The setup display appears.

3 Press the select button repeatedly

until “BTM” appears.

4 Press (SEEK) +.

The unit stores stations in order of frequency

on the number buttons.

A beep sounds when the setting is stored.

Storing manually

1 While receiving the station that you

want to store, press and hold a

number button ((1) to (6)) until

“MEM” appears.

The number button indication appears in the

display.

Note

If you try to store another station on the same number

button, the previously stored station will be replaced.

Tip

When a RDS station is stored, the AF/TA setting is

also stored (

page 9).

Receiving the stored stations

1 Select the band, then press a number

button ((1) to (6)).

Tuning automatically

1 Select the band, then press (SEEK) –/+

to search for the station.

Scanning stops when the unit receives a

station. Repeat this procedure until the

desired station is received.

Select To play

TRACK track repeatedly.

ALBUM*

1

album repeatedly.

GROUP*

2

group repeatedly.

SHUF ALBUM*

1

album in random order.

SHUF GROUP*

2

group in random order.

SHUF DISC disc in random order.

9

Tip

If you know the frequency of the station you want to

listen to, press and hold (SEEK)

–/+ to locate the

approximate frequency, then press (SEEK)

–/+

repeatedly to fine adjust to the desired frequency

(manual tuning).

RDS

Overview

FM stations with Radio Data System (RDS)

service send inaudible digital information along

with the regular radio program signal.

Display items

A TA/TP*

1

B Radio band, Function

C Frequency*

2

(Program service name), Preset

number, Clock, RDS data

*1 “TA” flashes during traffic information. “TP” lights

up while such a station is received.

*2 While receiving the RDS station, “ *” is displayed

on the left of the frequency indication.

To change display items C, press (DSPL).

RDS services

This unit automatically provides RDS services as

follows:

Notes

• Depending on the country/region, not all RDS

functions may be available.

• RDS will not work if the signal strength is too weak,

or if the station you are tuned to is not transmitting

RDS data.

Setting AF and TA

1 Press (AF/TA) repeatedly until the

desired setting appears.

Storing RDS stations with the AF and

TA setting

You can preset RDS stations along with the AF/

TA setting. If you use the BTM function, only

RDS stations are stored with the same AF/TA

setting.

If you preset manually, you can preset both RDS

and non-RDS stations with the AF/TA setting for

each.

1 Set AF/TA, then store the station with BTM or

manually.

Presetting the volume of traffic

announcememnts

You can preset the volume level of the traffic

announcements so as to not miss hearing them.

1 Rotate the volume control dial to adjust the

volume level.

2 Press and hold (AF/TA) until “TA” appears.

Receiving emergency

announcements

With AF or TA on, the emergency

announcements will automatically interrupt the

currently selected source.

Staying with one regional program

— REG

When the AF function is on: this unit’s factory

setting restricts reception to a specific region, so

you will not be switched to another regional

station with a stronger frequency.

If you leave this regional program’s reception

area, set “REG-OFF” in setup during FM

reception (

page 12).

Note

This function does not work in the UK and in some

other areas.

AF (Alternative Frequencies)

Selects and retunes the station with the

strongest signal in a network. By using this

function, you can continuously listen to the

same program during a long-distance drive

without having to retune the same station

manually.

TA (Traffic Announcement)/TP (Traffic

Program)

Provides current traffic information/programs.

Any information/program received, will

interrupt the currently selected source.

PTY (Program Types)

Displays the currently received program type.

Also searches your selected program type.

CT (Clock Time)

The CT data from the RDS transmission sets

the clock.

Select To

AF-ON activate AF and deactivate TA.

TA-ON activate TA and deactivate AF.

AF, TA-ON activate both AF and TA.

AF, TA-OFF deactivate both AF and TA.

continue to next page t

10

Local Link function (UK only)

This function enables you to select other local

stations in the area, even if they are not stored on

your number buttons.

1 During FM reception, press a number button

((1) to (6)) on which a local station is stored.

2 Within 5 seconds, press again a number button

of the local station.

Repeat this procedure until the local station is

received.

Selecting PTY

1 Press (PTY) during FM reception.

The current program type name appears if the

station is transmitting PTY data.

2 Press (PTY) repeatedly until the

desired program type appears.

3 Press (S EEK) –/+.

The unit starts to search for a station

broadcasting the selected program type.

Type of programs

Note

You cannot use this function in countries/regions

where no PTY data is available.

Setting CT

1 Set “CT-ON” in setup (page 12).

Notes

• The CT function may not work even though an RDS

station is being received.

• There might be a difference between the time set by

the CT function and the actual time.

USB devices

Playback USB devices

1 Connect the USB device to the USB

terminal.

Playback starts.

If a USB device is already connected, press

(SOURCE) repeatedly until “USB” appears, to

start playback.

Press (OFF) to stop playback.

Notes

• Before removing a USB device, be sure to stop

playback first. If you remove your USB device during

playback, data in the USB device may be damaged.

• Do not use USB devices so large or heavy that they

may fall down due to vibration, or cause a loose

connection.

Display items

A AAC/WMA/ATRAC/MP3 indication

B “Walkman” (ATRAC Audio Device):

ALB, ART, PLY

Mass Storage Class: USB

C Track/Album/Artist/Playlist number, Track/

Album/Artist/Playlist name, Elapsed playing

time, Clock

Note

The display differs depending on the Mass Storage

Class type USB device, and “Walkman” (ATRAC Audio

Device).

NEWS (News), AFFAIRS (Current Affairs),

INFO (Information), SPORT (Sports),

EDUCATE (Education), DRAMA (Drama),

CULTURE (Culture), SCIENCE (Science),

VARIED (Varied), POP

M (Popular Music),

ROCK

M (Rock Music), EASY M (Easy

Listening), LIGHT

M (Light Classical),

CLASSICS (Classical), OTHER

M (Other

Music Type), WEATHER (Weather),

FINANCE (Finance), CHILDREN (Children’s

Programs), SOCIAL

A (Social Affairs),

RELIGION (Religion), PHONE

IN (Phone In),

TRAVEL (Travel), LEISURE (Leisure), JAZZ

(Jazz Music), COUNTRY (Country Music),

NATION

M (National Music), OLDIES (Oldies

Music), FOLK

M (Folk Music), DOCUMENT

(Documentary)

11

Listening to music on a Mass

Storage Class type audio device

Repeat and shuffle play

1 During playback, press (3) (REP) or (4)

(SHUF) repeatedly until the desired setting

appears.

To return to normal play mode, select “ OFF”

or “SHUF OFF. ”

Listening to music on “Walkman”

(ATRAC Audio Device)

1 During playback, press (MODE)

repeatedly until the desired setting

appears.

The item changs as follows:

ALB (Album) t ART (Artist) t PLY

(Playlist)

Repeat and shuffle play

1 During playback, press (3) (REP) or (4)

(SHUF) repeatedly until the desired setting

appears.

To return to normal play mode, select “ OFF”

or “SHUF OFF. ”

Other functions

Changing the sound settings

Adjusting the sound

characteristics — BAL/FAD/SUB

You can adjust the balance, fader, and subwoofer

volume.

1 Press the select button repeatedly

until “BAL,” “FAD” or “SUB” appears.

The item changes as follows:

LOW*

1

t MID*

1

t HI*

1

t

BAL (left-right) t FAD (front-rear) t

SUB (subwoofer volume)*

2

t AUX*

3

*1 When EQ3 is activated (page 11).

*2 When the audio output is set to “SUB”

(page 12).

“ATT” is displayed at the lowest setting, and can

be adjusted up to 20 steps.

*3 When AUX source is activated (page 12).

2 Rotate the volume control dial to

adjust the selected item.

After 3 seconds, the setting is complete and

the display returns to normal play/reception

mode.

With the card remote commander

In step 2, to adjust the selected item, press <, M, ,

or m.

Customizing the equalizer curve

— EQ3

“CUSTOM” of EQ3 allows you to make your

own equalizer settings.

1 Select a source, then press (EQ3)

repeatedly to select “CUSTOM.”

2 Press the select button repeatedly

until “LOW,” “MID” or “HI” appears.

3 Rotate the volume control dial to

adjust the selected item.

The volume level is adjustable in 1 dB steps,

from –10 dB to +10 dB.

Repeat steps 2 and 3 to adjust the equalizer

curve.

To restore the factory-set equalizer curve,

press and hold the select button before the

setting is complete.

After 3 seconds, the setting is complete and

the display returns to normal play/reception

mode.

Select To play

TRACK track repeatedly.

ALBUM album repeatedly.

SHUF ALBUM album in random order.

SHUF DEVICE device in random order.

Select To play

TRACK track repeatedly.

ALBUM album repeatedly.

ARTIST artist repeatedly.

PLAYLIST playlist repeatedly.

SHUF ALBUM album in random order.

SHUF ARTIST artist in random order.

SHUF PLAYLIST playlist in random order.

SHUF DEVICE device in random order.

continue to next page t

12

Tip

Other equalizer types are also adjustable.

With the card remote commander

In step 3, to adjust the selected item, press <, M, ,

or m.

Adjusting setup items — SET

1 Press and hold the select button.

The setup display appears.

2 Press the select button repeatedly

until the desired item appears.

3 Rotate the volume control dial to

select the setting (example “ON” or

“OFF”).

4 Press and hold the select button.

The setup is complete and the display returns

to normal play/reception mode.

Note

Displayed items will differ, depending on the source

and setting.

With the card remote commander

In step 3, to select the setting, press < or ,.

The following items can be set (follow the page

reference for details):

“z” indicates the default settings.

Using optional equipment

Auxiliary audio equipment

By connecting an optional portable audio device

to the AUX input jack (stereo mini jack) on the

unit and then simply selecting the source, you

can listen on your car speakers. The volume level

is adjustable for any difference between the unit

and the portable audio device. Follow the

procedure below:

CLOCK-ADJ (Clock Adjust) (page 5)

CT (Clock Time)

To set “CT-ON” or “CT-OFF” (

z) (page 9, 10).

BEEP

To set “BEEP-ON” (

z) or “BEEP-OFF.”

AUX-A*

1

(AUX Audio)

To turn the AUX source display “AUX-A-ON”

(

z) or “AUX-A-OFF” (page 12).

A.OFF (Auto Off)

To shut off automatically after a desired time

when the unit is turned off.

– “A.OFF-NO” (

z), “A.OFF-30S (Seconds),”

“A.OFF-30M (Minutes)” or “A.OFF-60M

(Minutes).”

SUB/REAR*

1

To switch the audio output.

–“SUB-OUT” (

z): to output to a subwoofer.

– “REAR-OUT”: to output to a power amplifier.

DEMO*

1

(Demonstration)

To set “DEMO-ON” (z) or “DEMO-OFF.”

DIM (Dimmer)

To change the brightness of the display.

– “DIM-ON”: to dim the display.

– “DIM-OFF” (

z): to deactivate the dimmer.

ILM (Illumination)

To change the illumination color: “ILM-1” (

z)

or “ILM-2.”

A.SCRL (Auto Scroll)

To scroll long displayed item automatically

when the disc/album/track is changed.

– “A.SCRL-ON” (

z): to scroll.

– “A.SCRL-OFF”: to not scroll.

LOCAL (Local Seek Mode)

– “LOCAL-ON” : to only tune into stations with

stronger signals.

–“LOCAL-OFF” (

z): to tune normal reception.

MONO*

2

(Monaural Mode)

To improve poor FM reception, select monaural

reception mode.

– “MONO-ON” : to hear stereo broadcast in

monaural.

– “MONO-OFF” (

z): to hear stereo broadcast in

stereo.

REG*

2

(Regional)

To set “REG-ON” (

z) or “REG-OFF” (page 9).

LPF*

3

(Low Pass Filter)

To select the subwoofer cut-off frequency: “LPF

OFF” (

z), “LPF125Hz” or “LPF 78Hz.”

BTM (page 8)

*1 When the unit is turned off.

*2 When FM is received.

*3 When the audio output is set to “SUB.”

13

Connecting the portable audio

device

1 Turn off the portable audio device.

2 Turn down the volume on the unit.

3 Connect to the unit.

* Be sure to use a straight type plug.

Adjust the volume level

Be sure to adjust the volume for each connected

audio device before playback.

1 Turn down the volume on the unit.

2 Press (SOURCE) repeatedly until “AUX”

appears.

“AUX FRONT IN” appears.

3 Start playback of the portable audio device at a

moderate volume.

4 Set your usual listening volume on the unit.

5 Press the select button repeatedly until “AUX”

appears, and rotate the volume control dial to

adjust the input level (–8 dB to +18 dB).

CD/MD changer

Selecting the changer

1 Press (SOURCE) repeatedly until “CD” or

“MD” appears.

2 Press (MODE) repeatedly until the desired

changer appears.

Playback starts.

Skipping albums and discs

1 During playback, press (1)/(2) (GP/ALBM –

/+).

Repeat and shuffle play

1 During playback, press (3) (REP) or (4)

(SHUF) repeatedly until the desired setting

appears.

*1 When one or more CD/MD changers are

connected.

*2 When two or more MD changers are connected.

To return to normal play mode, select “ OFF”

or “SHUF OFF.”

AUX

Connecting cord*

(not supplied)

Disc number

Unit number

To skip

Press (1)/(2) (GP/ALBM –/

+)

album and release (hold for a

moment).

album

continuously

within 2 seconds of first

releasing.

discs repeatedly.

discs

continuously

then, press again within 2

seconds and hold.

Select To play

DISC*

1

disc repeatedly.

SHUF

CHANGER*

1

tracks in the changer in random

order.

SHUF ALL*

2

tracks in all units in random

order.

14

Additional Information

Precautions

• If your car has been parked in direct sunlight,

allow the unit to cool off before operating it.

• Power antenna (aerial) will extend automatically

while the unit is operating.

Moisture condensation

On a rainy day or in a very damp area, moisture

condensation may occur inside the lenses and

display of the unit. Should this occur, the unit will

not operate properly. In such a case, remove the disc

and wait for about an hour until the moisture has

evaporated.

To maintain high sound quality

Be careful not to splash juice or other soft drinks

onto the unit or discs.

Notes on discs

• To keep a disc clean, do not touch its surface.

Handle the disc by its edge.

• Keep your discs in their cases or disc magazines

when not in use.

• Do not subject discs to heat/high temperature.

Avoid leaving them in a parked car or on a

dashboard/rear tray.

• Do not attach labels, or use discs with sticky ink/

residue. Such discs may stop spinning when used,

causing a malfunction, or may ruin the disc.

• Do not use any discs with labels or stickers

attached.

The following malfunctions may result from using

such discs:

– Inability to eject a disc (due to a label or sticker

peeling off and jamming the eject mechanism).

– Inability to read audio data correctly (e.g.,

playback skipping, or no playback) due to heat

shrinking of a sticker or label causing a disc to

warp.

• Discs with non-standard shapes (e.g., heart,

square, star) cannot be played on this unit.

Attempting to do so may damage the unit. Do not

use such discs.

• You cannot play 8 cm (3

1

/4 in) CDs.

• Before playing, clean the discs

with a commercially available

cleaning cloth. Wipe each disc

from the center out. Do not use

solvents such as benzine,

thinner, commercially available

cleaners, or antistatic spray

intended for analog discs.

Notes on CD-R/CD-RW discs

• Some CD-Rs/CD-RWs (depending on the

equipment used for its recording or the condition

of the disc) may not play on this unit.

• You cannot play a CD-R/a CD-RW that is not

finalized.

• The unit is compatible with the ISO 9660 level 1/

level 2 format, Joliet/Romeo in the expansion

format, and Multi Session.

• The maximum number of:

– folders (albums): 150 (including root and empty

folders).

– files (tracks) and folders contained in a disc: 300

(if a folder/file names contain many characters,

this number may become less than 300).

– displayable characters for a folder/file name is

32 (Joliet), or 64 (Romeo).

• When the disc is recorded in Multi Session, only

the first track of the first session format is

recognized and played (any other format is

skipped). The priority of the format is CD-DA,

ATRAC CD and MP3/WMA/AAC.

– When the first track is a CD-DA, only CD-DA of

the first session is played.

– When the first track is not a CD-DA, an ATRAC

CD or MP3/WMA/AAC session is played. If the

disc has no data in any of these formats, “NO

MUSIC” is displayed.

Music discs encoded with copyright

protection technologies

This product is designed to play back discs that

conform to the Compact Disc (CD) standard.

Recently, various music discs encoded with

copyright protection technologies are marketed by

some record companies. Please be aware that among

those discs, there are some that do not conform to

the CD standard and may not be playable by this

product.

Note on DualDiscs

A DualDisc is a two sided disc product which

mates DVD recorded material on one side with

digital audio material on the other side. However,

since the audio material side does not conform to

the Compact Disc (CD) standard, playback on this

product is not guaranteed.

15

About USB devices

• Mass Storage Class and ATRAC Audio Device

type USB devices compliant with the USB

standard can be used. However, this unit cannot

recognize USB devices via a USB HUB, and is not

compatible with devices that have a HUB

function. For details on the compatibility of your

USB device, visit the Sony support website

(page 20).

• Corresponding codec is different according to

device type.

– Mass Storage Class: MP3/WMA/AAC

– ATRAC Audio Device: ATRAC/MP3/WMA/

AAC

• DRM (Digital Rights Management) files other

than ATRAC cannot be played.

• Displayable data are as follows.

Mass Storage Class:

– Folders (Albums): 512, Files (Tracks): 65535

ATRAC Audio Device: ATRAC/MP3/WMA/AAC

– Albums/Artists/Playlists: 65535, Tracks: 65535

Notes on USB devices

• When using a cable, use the one supplied with the

USB devices to connect.

• Do not use USB devices that are so large or heavy

that may interfere with driving operations.

• Do not leave USB devices in a parked car, as

malfunctions may result.

• It may take time for playback to begin, depending on

the amount of recorded data.

• Backup of data in USB devices is recommended.

Playback order of MP3/WMA/AAC

files

About MP3 files

• MP3, which stands for MPEG-1 Audio Layer-3, is

a music file compression format standard. It

compresses audio CD data to approximately 1/10

of its original size.

• ID3 tag versions 1.0, 1.1, 2.2, 2.3 and 2.4 apply to

MP3 only. ID3 tag is 15/30 characters (1.0 and

1.1), or 63/126 characters (2.2, 2.3 and 2.4).

• When naming an MP3 file, be sure to add the file

extension “.mp3” to the file name.

• During playback or fast-forward/reverse of a VBR

(variable bit rate) MP3 file, elapsed playing time

may not display accurately.

Note on MP3

If you play a high-bit-rate MP3, such as 320 kbps,

sound may be intermittent.

About WMA files

• WMA, which stands for Windows Media Audio,

is a music file compression format standard. It

compresses audio CD data to approximately 1/22*

of its original size.

• WMA tag is 63 characters.

• When naming a WMA file, be sure to add the file

extension “.wma” to the file name.

• During playback or fast-forward/reverse of a VBR

(variable bit rate) WMA file, elapsed playing time

may not display accurately.

* only for 64 kbps

Note on WMA

Playback of the following WMA files is not supported.

– lossless compression

– copyright-protected

About AAC files

• AAC, which stands for Advanced Audio Coding,

is a music file compression format standard. It

compresses audio CD data to approximately 1/11*

of its original size.

• AAC tag is 126 characters.

• When naming an AAC file, be sure to add the file

extension “.m4a” to the file name.

• During playback or fast-forward/reverse of a VBR

(variable bit rate) AAC file, elapsed playing time

may not display accurately.

* only for 128 kbps

Note on AAC

Playback of a copyright-protected file is not supported.

About ATRAC files

ATRAC3plus format

ATRAC3, which stands for Adaptive Transform

Acoustic Coding3, is audio compression

technology. It compresses audio CD data to

approximately 1/10 of its original size.

ATRAC3plus, which is an extended format of

ATRAC3, compresses the audio CD data to

approximately 1/20 of its original size. The unit

accepts both ATRAC3 and ATRAC3plus format.

• The ATRAC is in the structure of a 2-level

hierarchy; one folder (group), two files (tracks).

–ATRAC CD

The maximum number of folders (groups) is

255, and the maximum number of files (tracks)

is 999.

Folder

(album)

MP3/WMA/

AAC file

(track)

MP3/WMA/AAC

continue to next page t

16

– ATRAC Audio Device

The maximum number of albums/artists/

playlists is 65535, and the maximum number of

tracks is 65535.

• The characters for a folder/file name and text

information written by SonicStage are displayed.

For details on ATRAC CD and ATRAC Audio

Device, see the SonicStage manual.

Note

• Be sure to create the ATRAC files using authorized

software, such as SonicStage.

• ATRAC files cannot be played on USB devices other

than ATRAC Audio Device.

If you have any questions or problems concerning

your unit that are not covered in this manual, consult

your nearest Sony dealer.

Maintenance

Replacing the lithium battery of the

card remote commander

Under normal conditions, the battery will last

approximately 1 year. (The service life may be

shorter, depending on the conditions of use.)

When the battery becomes weak, the range of the

card remote commander becomes shorter.

Replace the battery with a new CR2025 lithium

battery. Use of any other battery may present a

risk of fire or explosion.

Notes on the lithium battery

• Keep the lithium battery out of the reach of children.

Should the battery be swallowed, immediately

consult a doctor.

• Wipe the battery with a dry cloth to assure a good

contact.

• Be sure to observe the correct polarity when

installing the battery.

• Do not hold the battery with metallic tweezers,

otherwise a short-circuit may occur.

Fuse replacement

When replacing the fuse, be

sure to use one matching the

amperage rating stated on the

original fuse. If the fuse blows,

check the power connection and

replace the fuse. If the fuse

blows again after replacement,

there may be an internal

malfunction. In such a case,

consult your nearest Sony

dealer.

Cleaning the connectors

The unit may not function properly if the connectors

between the unit and the front panel are not clean. In

order to prevent this, detach the front panel (page 5)

and clean the connectors with a cotton swab. Do not

apply too much force. Otherwise, the connectors

may be damaged.

Notes

• For safety, turn off the ignition before cleaning the

connectors, and remove the key from the ignition

switch.

• Never touch the connectors directly with your fingers

or with any metal device.

Removing the unit

1 Remove the protection collar.

1Detach the front panel (page 5).

2Engage the release keys together with the

protection collar.

1

2

+ side up

c

WARNING

Battery may explode if mistreated.

Do not recharge, disassemble, or dispose of

in fire.

Fuse (10A)

Main unit Back of the front

panel

Orient the release

keys as shown.

17

3 Pull out the release keys to remove the

protection collar.

2 Remove the unit.

1 Insert both release keys simultaneously

until they click.

2 Pull the release keys to unseat the unit.

3 Slide the unit out of the mounting.

Specifications

CD Player section

Signal-to-noise ratio: 120 dB

Frequency response: 10 – 20,000 Hz

Wow and flutter: Below measurable limit

Tuner section

FM

Tuning range: 87.5 – 108.0 MHz

Antenna (aerial) terminal:

External antenna (aerial) connector

Intermediate frequency: 10.7 MHz/450 kHz

Usable sensitivity: 9 dBf

Selectivity: 75 dB at 400 kHz

Signal-to-noise ratio: 67 dB (stereo), 69 dB (mono)

Harmonic distortion at 1 kHz: 0.5 % (stereo),

0.3 % (mono)

Separation: 35 dB at 1 kHz

Frequency response: 30 – 15,000 Hz

MW/LW

Tuning range:

MW: 531 – 1,602 kHz

LW: 153 – 279 kHz

Antenna (aerial) terminal:

External antenna (aerial) connector

Intermediate frequency: 10.7 MHz/450 kHz

Sensitivity: MW: 30 µV, LW: 40 µV

USB Player section

Interface: USB (Full-speed)

Maximum current: 500mA

Power amplifier section

Outputs: Speaker outputs (sure seal connectors)

Speaker impedance: 4 – 8 ohms

Maximum power output: 50 W × 4 (at 4 ohms)

General

Output:

Audio outputs terminal (sub/rear switchable)

Power antenna (aerial) relay control terminal

Power amplifier control terminal

Inputs:

Telephone ATT control terminal

BUS control input terminal

BUS audio input terminal

Antenna (aerial) input terminal

AUX input jack (stereo mini jack)

Tone controls:

Low: ±10 dB at 60 Hz (XPLOD)

Mid: ±10 dB at 1 kHz (XPLOD)

High: ±10 dB at 10 kHz (XPLOD)

Power requirements: 12 V DC car battery

(negative ground (earth))

Dimensions: Approx. 178 × 50 × 179 mm

(7

1

/8 × 2 × 7

1

/8 in) (w/h/d)

Mounting dimensions: Approx. 182 × 53 × 162

mm(7

1

/4 × 2

1

/8 × 6

1

/2 in) (w/h/d)

Mass: Approx. 1.2 kg (2 lb 11 oz)

Supplied accessories:

USB cap

Card remote commander: RM-X151

Parts for installation and connections (1 set)

Optional accessories/equipment:

BUS cable (supplied with an RCA pin cord):

RC-61 (1 m), RC-62 (2 m)

CD changer (10 discs): CDX-757MX

CD changer (6 discs): CDX-T70MX, CDX-T69

Source selector: XA-C40

AUX-IN selector: XA-300

Interface adaptor for iPod: XA-110IP

Your dealer may not handle some of the above listed

accessories. Please ask the dealer for detailed

information.

Hook facing

inwards.

continue to next page t

US and foreign patents licensed from Dolby

Laboratories.

MPEG Layer-3 audio coding technology and

patents licensed from Fraunhofer IIS and Thomson.

18

Design and specifications are subject to change

without notice.

Troubleshooting

The following checklist will help you remedy

problems you may encounter with your unit.

Before going through the checklist below, check the

connection and operating procedures.

General

No power is being supplied to the unit.

• Check the connection. If everything is in order, check

the fuse.

• If the unit is turned off and the display disappears, it

cannot be operated with the remote commander.

tTurn on the unit.

The power antenna (aerial) does not extend.

The power antenna (aerial) does not have a relay box.

No sound.

• The volume is too low.

• The ATT function is activated, or the Telephone ATT

function (when the interface cable of a car telephone

is connected to the ATT lead) is activated.

• The position of the fader control “FAD” is not set for

a 2-speaker system.

• The CD changer is incompatible with the disc (MP3/

WMA/AAC/ATRAC CD).

tPlay back with this unit.

No beep sound.

• The beep sound is canceled (page 12).

• An optional power amplifier is connected and you are

not using the built-in amplifier.

The contents of the memory have been erased.

• The RESET button has been pressed.

tStore again into the memory.

• The power supply lead or battery has been

disconnected.

• The power supply lead is not connected properly.

Stored stations and correct time are erased.

The fuse has blown.

Makes noise when the position of the ignition

is switched.

The leads are not matched correctly with the car’s

accessory power connector.

• Halogenated flame retardants are not used in the

certain printed wiring boards.

• Halogenated flame retardants are not used in

cabinets.

• Paper is used for the packaging cushions.

• VOC (Volatile Organic Compound)-free vegetable

oil based ink is used for printing the carton.

The display disappears from/does not appear

in the display window.

• The dimmer is set “DIM-ON” (page 12).

• The display disappears if you press and hold (OFF).

t Press and hold (OFF) on the unit until the

display appears.

• The connectors are dirty (page 16).

The Auto Off function does not operate.

The unit is turned on. The Auto Off function activates

after turning off the unit.

t Turn off the unit.

Card remote commander operation is not

possible.

Make sure the insulation film has been removed

(page 4).

CD/MD playback

The disc cannot be loaded.

• Another disc is already loaded.

• The disc has been forcibly inserted upside down or in

the wrong way.

The disc does not playback.

• Defective or dirty disc.

• The CD-Rs/CD-RWs are not for audio use (page 14).

• The disc format and file version are incompatible

with this unit (For details, refer to page 4 and 14).

MP3/WMA/AAC files cannot be played back.

The disc is incompatible with the MP3/WMA/AAC

format and version (page 15).

MP3/WMA/ACC files take longer to play back

than others.

The following discs/devices take a longer time to start

playback.

– a disc/device recorded with a complicated tree

structure.

– a disc/device recorded in Multi Session.

– a disc/device to which data can be added.

The ATRAC CD cannot play.

• The disc is not created by authorized software, such

as SonicStage or SonicStage Simple Burner.

• Tracks that are not included in the group cannot be

played.

The display items do not scroll.

• For discs with very many characters, those may not

scroll.

• “A.SCRL” is set to “OFF”.

t Set “A.SCRL-ON” (page 12) or press (SCRL) on

the card remote commander.

The sound skips.

• Installation is not correct.

t Install the unit at an angle of less than 45° in a

sturdy part of the car.

• Defective or dirty disc.

The operation buttons do not function.

The disc will not eject.

Press the RESET button (page 4).

19

Error displays/Messages

Radio reception

The stations cannot be received.

The sound is hampered by noises.

• Connect a power antenna (aerial) control lead (blue)

or accessory power supply lead (red) to the power

supply lead of a car’s antenna (aerial) booster (only

when your car has built-in FM/MW/LW antenna

(aerial) in the rear/side glass).

• Check the connection of the car antenna (aerial).

• The auto antenna (aerial) will not go up.

t Check the connection of the power antenna

(aerial) control lead.

• Check the frequency.

Preset tuning is not possible.

• Store the correct frequency in the memory.

• The broadcast signal is too weak.

Automatic tuning is not possible.

• Setting of the local seek mode is not correct.

t Tuning stops too frequently:

Set “LOCAL-ON” (page 12).

t Tuning does not stop at a station:

Set “MONO-ON” (page 12).

• The broadcast signal is too weak.

t Perform manual tuning.

During FM reception, the “ST” indication

flashes.

• Tune in the frequency accurately.

• The broadcast signal is too weak.

t Set “MONO-ON” (page 12).

An FM program broadcast in stereo is heard in

monaural.

The unit is in monaural reception mode.

tSet “MONO-OFF” (page 12).

RDS

The SEEK starts after a few seconds of

listening.

The station is non-TP or has weak signal.

tDeactivate TA (page 9).

No traffic announcements.

• Activate TA (page 9).

• The station does not broadcast any traffic

announcements despite being TP.

t Tune in another station.

PTY displays “- - - - - - - -.”

• The current station is not an RDS station.

• RDS data has not been received.

• The station does not specify the program type.

USB playback

You cannot play back items via a USB HUB.

This unit cannot recognize USB devices via a USB

HUB, and is not compatible with a device that has a

HUB function.

Cannot play back items.

• Play back music files are protected by Digital Rights

Management (DRM) technology (page 15).

• Play back items on non-Mass Storage Class USB

devices only.

• If a USB device does not work, reconnect it.

A beep sounds.

During playback, the USB device has been

disconnected.

t Before disconnecting a USB device, make sure to

stop playback first for data protection.

The sound is intermittent.

The sound may be intermittent at a high-bit-rate of

more than 320 kbps.

BLANK*

1

Tracks have not been recorded on the MD.*

2

t Play an MD with recorded tracks.

CHECKING

The unit is confirming the connection of a USB device.

t Wait until confirming the connection is finished.

ERROR*

1

• The disc is dirty or inserted upside down.*

2

t Clean or insert the disc correctly.

• A blank disc has been inserted.

• The disc cannot play due to a problem.

t Insert another disc.

• USB device was not automatically recognized.

t Reconnect it again.

FAILURE

The connection of speakers/amplifiers is incorrect.

t See the installation guide manual of this model to

check the connection.

HUB NO SUPRT

USB HUB or devices that have a HUB function are not

supported on this unit.

LOAD

The changer is loading the disc.

t Wait until loading is complete.

L. SEEK +/–

The local seek mode is on during automatic tuning.

NO AF

There is no alternative frequency for the current

station.

t Press (SEEK) –/+ while the program service name

is flashing. The unit starts searching for another

frequency with the same PI (Program

Identification) data (“PI SEEK” appears).

NO DEV (No Device)

(SOURCE) is selected without a USB device

connected. A USB device or a USB cable has been

disconnected during playback.

t Be sure to connect a USB device and USB cable.

continue to next page t

20

If these solutions do not help improve the situation,

consult your nearest Sony dealer.

If you take the unit to be repaired because of CD

playback trouble, bring the disc that was used at the

time the problem began.

NO DISC

The disc is not inserted in the CD/MD changer.

t Insert discs in the changer.

NO INFO

Text information is not written in the MP3/WMA/

AAC files or ATRAC CD.

NO MAG

The disc magazine is not inserted in the CD changer.

t Insert the magazine in the changer.

NO MUSIC

The disc/USB device does not contain a music file.

t Insert a music CD in this unit or MP3 playable

changer.

t Connect a USB device with a music file in it.

NO NAME

A disc/album/group/track name is not written in the

track.

NO TP

The unit will continue searching for available TP

stations.

NOT READ

The disc information has not been read by the unit.

t Load the disc, then select it on the list.

NOTREADY

The lid of the MD changer is open or the MDs are not

inserted properly.

t Close the lid or insert the MDs properly.

OFFSET

There may be an internal malfunction.

t Check the connection. If the error indication

remains on in the display, consult your nearest

Sony dealer.

OVERLOAD

USB device is overloaded.

t Disconnect the USB device, then change the source

by pressing (SOURCE).

t Indicates that the USB device is out of order, or an

unsupported device is connected.

READ

The unit is reading all track and group/album

information on the disc/USB device.

t Wait until reading is complete and playback starts

automatically. Depending on the disc/USB device

structure, it may take more than a minute.

RESET

The CD unit and CD/MD changer cannot be operated

due to a problem.

t Press the RESET button (page 4).

USB NO SUPRT (USB Not Support)

The connected USB device is not supported.

t Connect a USB device of Mass Storage Class

(page 15).

“ ” or “ ”

During reverse or fast-forward, you have reached the

beginning or the end of the disc and you cannot go any

further.

“ ”

The character cannot be displayed with the unit.

*1 If an error occurs during playback of a CD or MD,

the disc number of the CD or MD does not appear

in the display.

*2 The disc number of the disc causing the error

appears in the display.

Support site

If you have any questions or for the latest

support information on this product, please

visit the web site below:

http://support.sony-europe.com

La page charge ...

Sony CDX-GT410U Le manuel du propriétaire

Ce manuel convient également à

Sony CDX-GT410U Le manuel du propriétaire

dans d''autres langues

Documents connexes