Polaris TR28P Le manuel du propriétaire

Marque: Polaris

Modèle: TR28P

Catégorie: Accessoires de piscine hors terre

Taper: Le manuel du propriétaire

OWNER’S MANUAL

English

Français

Español

H0646500_REVA

English

For customer service or support:

• Before installing the Polaris

cleaner, make sure the pool filter is clean.

• New plumbing lines should be flushed out before installing the cleaner.

• The cleaner should not be used to remove plaster dust in new pools.

• Except when checking the wheel RPM, do not handle the cleaner while it is operating.

• Always remove the cleaner before swimmers enter the pool.

• Disconnect the cleaner from the pool wall when cleaning or backwashing the pool filter.

• Always remove the cleaner from the pool before chemical shock treatments.

• After cleaning or backwashing, let the filtration system run for at least five minutes before

re-connecting the cleaner.

To avoid risk of potentially serious injury:

• Do not handle the Polaris cleaner while it is operating, except when checking the wheel RPM.

• Always remove the Polaris cleaner before swimmers enter the pool.

CAUTION

Before You Start: Important Information

WARNING

USE OF A POLARIS TR28P IN A VINYL LINER POOL

Certain vinyl liner patterns are particularly susceptible to rapid surface wear or pattern removal caused by

objects coming into contact with the vinyl surface, including pool brushes, pool toys, oats, fountains, chlorine

dispensers, and automatic pool cleaners. Some vinyl liner patterns can be seriously scratched or abraded

simply by rubbing the surface with a pool brush. Ink from the pattern can also rub off during the installation

process or when it comes into contact with objects in the pool. Zodiac Pool Systems LLC and its afliates and

subsidiaries are not responsible for, and the Limited Warranty does not cover, pattern removal, abrasion or

markings on vinyl liners.

Zodiac Pool Systems LLC

2620 Commerce Way, Vista, CA 92081

1.800.822.7933 | polarispool.com

Zodiac Pool Care Europe

Boulevard de la Romanerie -BP 90023

49180 St. Barthelemy d’Anjou cedex FRANCE

zodiac-poolcare.fr

Zodiac Pool Systems Canada, Inc.

2-3365 Mainway, Burlington, ON L7M 1A6

1.800.822.7933 | ZodiacPoolSystems.ca

Zodiac Group Australia PTY, Ltd.

19 Woodpark Rd. Smithfield

NSW, 2164

1300 763 021 | Zodiac.com.au

original instructions

English

a - Cleaner Body

b - All-Purpose Zipper Bag

c - Head Float

d - Sweep Hose

e - TailSweep PRO

with Sweep Hose Scrubber

f - Feed Pipe with Elbow

g - Leader Hose

h - Hose Floats

i - Back-up Valve

j - Center Swivel

k - Feed Hose

l - In-Line Filter Assembly

m - Quick Disconnect with Pressure Relief Valve (m

)

n - Universal Wall Fitting (UWF

)

o - Restrictor Disks - (blue disk installed / red disk in bag)

p - Hose Nut

q - Bag Clip

Included in the Box

English

Installing the Cleaner

Read the complete owner’s

manual before you begin installation.

Flush Plumbing Lines

1. Turn on the filtration pump, allow to prime. Then turn on the booster

pump and flush plumbing lines for five minutes.

2. Turn off both pumps.

Install the Universal Wall Fitting (UWF)

The UWF installs on pools with a dedicated cleaner return line and a threaded

1-1/2” female pipe fitting.

1. Remove the Universal Wall Fitting (UWF) (n) with Blue Restrictor Disk (o)

from the Quick Disconnect (m).

2. Thread the UWF (n) with Blue Restrictor Disk (o) in place, into the

dedicated cleaner return line opening.

dedicated

cleaner return

line

English

Adjust Hose Assembly

3a.

Adjust Leader Hose Length to the Greatest Depth of

the Pool

Leader Hose

1. Straighten the Hose Assembly by laying it out flat in the sun.

2. Identify the Leader Hose section (g), marked Polaris

Leader Hose.

3. Measure and mark the greatest depth of

the pool, usually at the main drain,

by using a telescopic pool pole.

4. Lay the telescopic pool pole next to the

Leader Hose (g) starting from the end of

the Leader Hose near the Back-Up Valve

(i). Transfer the water level mark from the

telescopic pole onto the Leader Hose (g).

NOTE: If the pool depth is 10 feet (3m)

or more, DO NOT cut the Leader Hose. Go to Section 3b: Adjust Feed Hose to Fit Pool

Length.

water level mark

= greatest

depth of the

pool

5. Cut the Leader Hose (g) at the mark (do not cut off the float). Detach the excess Leader

Hose from the swivel and discard.

6. Reattach the Leader Hose (g) to the Feed Hose (k) at the swivel.

NOTE: It is easier to reinstall the swivel when hose and swivel are wet.

greatest depth of pool

English

3b.

Adjust Feed Hose Length to Fit Pool Length

1. Connect the Hose Assembly to the dedicated cleaner

return line opening by turning the Quick Disconnect

(m) clockwise into the UWF

(n) and pulling away to

secure.

2. Extend the end of the hose to the farthest point

of the pool. Do not include steps or seating areas.

6" (15 cm)

+ / –

3. The cleaner’s optimal hose length should be within 6˝ (15cm), longer or shorter, of the

farthest point (see image). The hose portion that extends past the farthest point is the

hose overage. See hose adjustment instructions below.

Hose too long?

- With the hose assembly laid on the deck, identify the Center Swivel (j).

- Slide the Hose Floats away from the Center Swivel (j) and separate the swivel from the hose.

- Cut half of the overage from each end of the hose sections that attach to the Center Swivel (j).

- Reconnect hose sections with the Center Swivel (j) . Make sure the flow direction arrow ( ) on

the Center Swivel (j) points toward the cleaner.

Hose too short?

- Add a Feed Hose section with floats, a swivel, and two hose nuts, available through your local

Polaris

dealer. Do not add more than one 10 ft. (3m) hose section.

- Adjust to proper length.

4. Position the first Hose Float (h) against the back-up valve (i) and the next Hose Float

within 2-3 ft (60-90 cm). Position the remaining Hose Floats (h) 1.5 - 3 ft. on the Hose

Assembly as shown.

1.5 ft - 3 ft

(45 - 90cm)

oint

Leader Hose Floats

2-3' apart

Leader Hose

Length = Max. Depth

2 ft - 3 ft

(60 - 90cm)

English

1/2" - 1"

1,3 - 2,5 cm

1. Use the Hose Nut (p) to attach the Leader Hose (g) to the Feed Pipe (f).

NOTE: Tighten the Hose Nut by turning counter-clockwise.

2. Attach the bag to the Leader Hose (g) with the Bag Clip (q).

3. Position the Head Float (c) 1/2” to 1” back from the Feed Pipe (as shown).

4. Turn on the filter pump and allow it to prime before turning on the booster pump.

Assemble the Cleaner

WARNING

To avoid risk of potentially serious injury, do not swim or use the pool

when the cleaner is submerged or operating.

English

Check for Proper Wheel RPM

Before operating the cleaner, check for proper wheel revolutions per minute (RPM). For

maximum efficiency, the cleaner should operate between 28 and 32 RPM.

1. Mark the single-side wheel using using a piece of tape (or a small leaf tucked into

the tire).

2. Turn the booster pump on, hold the cleaner below the water level and count wheel

revolutions for one minute. Hold the Sweep Hose (d) to avoid getting wet.

3. Optimum wheel speed should be between 28 and 32 RPM. If the count is not in

target range, refer to section 6: Adjust the Wheel Speed.

1 min

28 - 32 RPM

IMPORTANT

Keep cleaner

submerged for

accurate wheel

speed count.

mark the single-side

wheel (tape or small leaf)

NOTE: If Back-Up Valve engages during timing, start over.

English

Adjust the Wheel Speed

< 28 RPM

• Check the filter screen in the In-Line

Filter Assembly (l) for debris and rinse

with clean water.

• Clear any debris from the skimmer,

filter, and pump basket that could

restrict water flow.

• Check hoses, connections, and

swivels (j) for excessive leaking or

spraying. Verify flow direction arrow

( ) is toward the cleaner.

• Remove the blue restrictor disk (o)

from the UWF

> 32 RPM

• Replace the Blue Restrictor Disk (o)

in the UWF with the Red Restrictor

Disk (o).

flow

couler

fluir

red

rouge

rojo

• Loosen the Pressure Relief Valve (m

)

at the Quick Disconnect (m) until the

proper RPM is reached.

NOTE: The Pressure Relief Valve

should only be adjusted when a

restrictor disk is installed.

English

Fine tune your cleaner for optimal operation, as necessary.

The Sweep Hose (d) should move in a gentle sweeping motion. To increase

or decrease sweeping motion:

1. Turn the booster pump OFF.

2. Rotate the sweep hose screw on the Feed Pipe (f).

Decrease

motion

Increase

motion

If the cleaner is veering left or right instead of tracking straight, adjust the

thrust jet (on the back of the cleaner) for climbing or turning.

NOTE: Factory default setting is straight back. Only adjust the thrust jet to

accomodate unique pool shapes.

Turning

Climbing

Fine Tuning the Cleaner

Adjust the Sweep Hose

Adjust the Thrust Jet

When operating correctly, the Polaris

cleaner vacuums, sweeps and scrubs all surfaces randomly

throughout the pool. The climbing ability depends on the pool’s shape and water pressure or flow.

The cleaner climbs best in pools without sharp angles or curves in the transition from the pool floor

to the pool wall. Approximately every 3-1/2 minutes the cleaner goes into back-up mode. This action

pulls the cleaner away from pool obstacles and increases its random pattern.

English

Routine Maintenance

Empty the Bag

Clean the In-Line Filter

Storage/Winterizing

Perform routine maintenance to prolong the life of your cleaner.

1. Remove the bag clip (q) from the feed hose.

2. Twist the bag connector until it disengages with

a clicking sound from the vacuum tube and

remove the filter bag.

3. Open the zipper and empty out the debris.

4. To replace the bag, align the markings on the

connector and the vacuum tube.

5. Click the connector into position on the vacuum

tube and reattach the bag clip to the hose.

Empty the bag when it is half full, especially if the debris load is sand.

NOTE: It is easier to empty the bag when it is dry. Alternate between two bags.

To clean the in-line filter screen:

1. Remove the filter screen from the

assembly, as shown.

2. Rinse with clean water.

3. Press the filter screen firmly back in

place and tighten assembly.

NOTE: Never store the cleaner in direct sunlight.

To store the cleaner for the winter:

1. Remove cleaner from the pool and drain all water to avoid freezing water damage

(freeze damage is not covered under the warranty).

2. Remove the UWF from the pool wall using the Quick Disconnect. Use a pulling

pressure as you unscrew.

If necessary, use the UWF Removal Tool (part #10-102-00) available from

any Polaris

dealer.

Bag Collar

Zipper

Closure

English

Troubleshooting

Problem Solution

Cleaner hangs up on steps or other

obstacles for longer than 3

minutes.

1. Check the wheel RPM.

2. Verify the back-up valve is cycling.

3. Adjust the thrust jet.

4. Remove unnecessary pool hardware or install a Ladder

Guard Kit (part # G21) from a Polaris

dealer.

Cleaner is sluggish, running with less

power than normal.

1. Check the filter screen in the in-line filter and clean, if

necessary.

2. Clean the skimmer basket, pump basket, and pool

filter.

3. Check all of the hoses, connections, and swivels for

leaks that could cause loss of water pressure.

4. Check the wheel RPM.

Cleaner flies around the pool and/or

does not make contact with

the bottom.

1. Confirm that the blue restrictor disk is installed in

the UWF to decrease water flow. Or, install the red

restrictor disk to decrease water flow even more.

2. Check the wheel RPM. If more than 32 RPM, unscrew

the pressure relief valve to decrease water flow to

the cleaner. Note: The pressure relief valve should only

be adjusted when a restrictor disk is installed.

3. Verify the back-up valve is cycling. Hold the valve out

of the water and watch the jet. It should come on and

go off.

Cleaner does not back up. 1. Verify the back-up valve is cycling.

2. Check the wheel RPM.

3. If the bag is full, empty it.

4. If the head float has water in it, replace it.

5. Make sure feed hose is floating.

Cleaner only turns in one direction. 1. Adjust the thrust jet.

2. Make sure feed hose is floating.

English

Problem Solution

Feed hose becomes tangled. 1. Remeasure the hose to verify that it is adjusted to the

proper length for the pool shape.

2. With the cleaner operating, check that the swivels in

the hose and the hose connections turn freely.

3. Make sure feed hose is floating.

4. With the cleaner turned off, spin each of the wheels.

All wheels should turn together.

Sweep hose is sucked into

the vacuum tube.

1. Make sure the opening at the end of the sweep hose is

not blocked by the sweep hose scrubber.

2. Adjust the sweep hose to a gentle sweeping motion.

Sweep hose sprays too much water

out of the pool.

1. Verify the TailSweep PRO

is installed correctly.

2. Adjust the speed of the sweep hose by tightening the

adjustment screw.

3. Replace the sweep hose scrubber if it is worn or

missing.

4. Add a sweep hose weight (part #B2) available through

a Polaris

dealer.

The cleaner does not clean the

entire pool.

1. Check the hose length reaches within 6” of the farthest

point of the pool. If not, order a new hose section from

your

Polaris dealer.

2. Check thrust jet for straight back position that optimizes

random turning.

3. While the cleaner is operating, hold it upside down

and look into the vacuum tube. There should be two

distinct, even jets of water. If there are not, contact

Customer Service or a Polaris dealer for assistance.

The cleaner is running in circles on

its side.

1. Check filter bag, if full it can weigh the cleaner down on

one side.

2. Remove the head float and shake it. If there is water in

the float, order a new one.

3. Check the hose floats to ensure they are spaced

evenly.

Zodiac Pool Systems LLC

2620 Commerce Way, Vista, CA 92081

1.800.822.7933 | polarispool.com

Zodiac Pool Care Europe

Boulevard de la Romanerie -BP 90023

49180 St. Barthelemy d’Anjou cedex FRANCE

zodiac-poolcare.fr

Zodiac Pool Systems Canada, Inc.

2-3365 Mainway, Burlington, ON L7M 1A6

1.800.822.7933 | ZodiacPoolSystems.ca

Zodiac Group Australia PTY, Ltd.

19 Woodpark Rd. Smithfield

NSW, 2164

1300 763 021 | Zodiac.com.au

2018 Zodiac Pool Systems LLC H0646400 REV A

Polaris

y el diseño de limpiafondos de tres ruedas son marcas registradas de Zodiac Pool Systems, Inc.

Las demás marcas mencionadas en esta guía son propiedad de sus respectivos propietarios.

Polaris

and the 3-wheeled cleaner design are registered trademarks of Zodiac Pool Systems, Inc.

All other trademarks referenced herein are the property of their respective owners.

Polaris

et la conception de nettoyeur à 3 roues sont des marques déposées de Zodiac Pool Systems, Inc.

Toutes les autres marques de commerce citées dans le présent document appartiennent à leurs propriétaires respectifs.

MANUEL UTILISATEUR

Français

H0646500_REVA

Français

Pour contacter le service clientèle ou le support :

• Avant d'installer le nettoyeur Polaris

, assurez-vous que le filtre de la piscine est propre.

• Les nouvelles conduites de plomberie doivent être rincées avant d'installer le nettoyeur.

• Le nettoyeur ne doit pas être utilisé pour éliminer la poussière de plâtre dans les nouvelles piscines.

• Sauf lors du contrôle de la vitesse de rotation de la roue, ne manipulez pas le robot pendant qu'il

fonctionne.

• Retirez toujours le nettoyeur avant que des personnes pénètrent dans la piscine.

• Débranchez le nettoyeur de la paroi de la piscine lors du nettoyage ou du lavage à contre-courant du

filtre de la piscine.

• Retirez toujours le nettoyeur de la piscine avant tout traitement chimique.

• Après le nettoyage ou le lavage à contre-courant, laissez le système de filtration fonctionner pendant

au moins cinq minutes avant de rebrancher le nettoyeur.

Pour éviter les risques de blessures potentiellement graves :

• Ne manipulez pas le nettoyeur Polaris pendant son fonctionnement, sauf lors de la vérification

de la vitesse de la roue.

• Retirez toujours le nettoyeur Polaris avant que des personnes pénètrent dans la piscine.

ATTENTION

Avant de commencer : informations importantes

AVERTISSEMENT

UTILISATION D'UN POLARIS TR28P DANS UNE PISCINE AVEC LINER EN VINYLE

La surface de certains revêtements vinyle à motifs est particulièrement sensible et peut s'user rapidement et

les motifs peuvent disparaître au contact d'objets tels que brosses de nettoyage, jouets, bouées, fontaines,

distributeurs de chlore et nettoyeur de piscine automatique. Les motifs de certains revêtements vinyle peuvent

être égratignés ou usés par simple frottement, tel qu'avec une brosse de piscine. La couleur du motif peut

également s'effacer pendant l'installation ou en cas de contact avec des objets présents dans la piscine. Les

motifs effacés, l'usure ou l'égratignure des revêtements vinyle ne relèvent pas de la responsabilité des Zodiac

Pool Systems LLC, ses sociétés afliées ou ses liales, et ne sont pas couvertes par la garantie limitée.

Zodiac Pool Systems LLC

2620 Commerce Way, Vista, CA 92081

1.800.822.7933 | polarispool.com

Zodiac Pool Care Europe

Boulevard de la Romanerie -BP 90023

49180 St. Barthelemy d'Anjou cedex FRANCE

zodiac-poolcare.fr

Zodiac Pool Systems Canada, Inc.

2-3365 Mainway, Burlington, ON L7M 1A6

1.800.822.7933 | ZodiacPoolSystems.ca

Zodiac Group Australia PTY, Ltd.

19 Woodpark Rd. Smithfield

NSW, 2164

1300 763 021 | Zodiac.com.au

Instructions d'origine

Français

a - Corps du nettoyeur

b - Sachet à glissière tout usage

c - Flotteur de tête

d - Tuyau de balayage

e - TailSweep PRO

avec nettoyeur de

tuyau de balayage

f - Tuyau d'alimentation avec coude

g - Tuyau de raccordement

h - Flotteurs

i - Vanne de secours

j - Pivot central

k - Tuyau d'alimentation

l - Assemblage de filtre en ligne

m - Déconnexion rapide avec valve de décharge de pression (m

)

n - Raccord mural universel (UWF

)

o - Disques restricteurs - (disque bleu installé / disque rouge dans

le sac)

p - Écrou de tuyau

q - Clip de sac

Contenu de la boîte

Français

Installation du nettoyeur

Lisez tout le manuel d'utilisation

avant de commencer.

Rincer les canalisations de plomberie

1. Mettre en marche la pompe de filtration, laisser s'amorcer. Mettre en

marche le suppresseur et purger les canalisations pendant 5 minutes.

2. Arrêter les deux pompes.

Installer le raccord mural universel fileté (UWF)

L'UWF s'installe sur les piscines avec une conduite de retour de nettoyeur

dédiée et un raccord fileté femelle 3.8 cm.

1. Retirez le raccord mural universel (UWF) (n) avec le disque restricteur bleu

(o) de la déconnexion rapide (m).

2. Vissez l'UWF (n), avec le disque restricteur bleu (o) en place, dans

l'ouverture de la ligne de retour dédiée du nettoyeur.

ligne de

retour dédiée

du nettoyeur

Français

Ajuster l'assemblage du tuyau

3a.

Ajustez la longueur du tuyau de raccordement à la

plus grande profondeur de la piscine

Tuyau de raccordement

1. Redressez l'assemblage du tuyau en l'étendant à plat au soleil.

2. Identifiez la section du tuyau de raccordement (g), marquée Polaris

Leader Hose.

3. Mesurez et marquez la plus grande profondeur de la piscine, habituellement au drain

principal, en utilisant une perche de

piscine télescopique.

4. Posez la perche de piscine télescopique

à côté du tuyau de raccordement (g)

à partir de l'extrémité du tuyau de

raccordement près de la vanne de

secours (i). Transférez la marque de

niveau d'eau de la perche télescopique

sur le tuyau de raccordement (g).

REMARQUE : Si la profondeur de la piscine est de 3m ou plus, NE PAS couper le

tuyau de raccordement. Allez à la section 3b : Ajuster le tuyau d'alimentation à la

longueur de la piscine.

marque de niveau d'eau.

= plus grande

profondeur de

la piscine

5. Coupez le tuyau de raccordement (g) à la marque (ne pas couper le flotteur). Détachez

l'excès de tuyau de raccordement du pivot et jetez-le.

6. Rattachez le tuyau de raccordement (g) au tuyau d'alimentation (k) au pivot.

REMARQUE : Il est plus facile de réinstaller le pivot lorsque le tuyau et le pivot sont mouillés.

plus grande profondeur

de la piscine

Français

3b.

Ajuster le tuyau d'alimentation à la longueur de la piscine

1. Raccordez l'ensemble de tuyau à l'ouverture dédiée

de la conduite de retour du nettoyeur en tournant la

déconnexion rapide (m) dans le sens des aiguilles

d'une montre dans le raccord mural universel (n) et en

tirant pour le fixer.

2. Étendez l'extrémité du tuyau jusqu'au point le plus

éloigné de la piscine. N'incluez pas les marches ou les

zones de sièges.

6" (15 cm)

+ / -

3. L'extrémité du tuyau doit être à plus ou moins 15 cm (6 po) du point le plus éloigné

(voir l'image). La portion de tuyau qui dépasse du point le plus éloigné est le tuyau

excédentaire. Voir les instructions de réglage du tuyau ci-dessous.

Tuyau trop long ?

- Avec l'assemblage du tuyau posé au sol, identifiez le pivot central (j).

- Faites glisser les flotteurs du tuyau à l'écart du pivot central (j) et séparez le pivot du tuyau.

- Coupez la moitié de la quantité excédentaire de chaque extrémité des sections de tuyau qui se

fixent au pivot central (j).

- Rebranchez les sections de tuyau avec le pivot central (j). Assurez-vous que la flèche de direction

d'écoulement (

) sur le pivot central (j) est pointée vers le nettoyeur.

Tuyau trop court ?

- Ajoutez une section de tuyau d'alimentation, un pivot et deux écrous de tuyau, disponibles chez

votre revendeur Polaris

local. N'ajoutez pas plus d'une section de tuyau de 3 m.

- Ajustez à la bonne longueur.

4. Positionnez le premier flotteur de tuyau (h) contre la valve de secours (i) et le flotteur de

tuyau suivant à une distance de 60 à 90 cm. Positionnez les flotteurs de tuyau restants

(h) à 45-90 cm sur l'ensemble de tuyau comme indiqué.

45 - 90 cm

oint

Leader Hose Floats

2-3' apart

Leader Hose

Length = Max. Depth

60 - 90 cm

La page charge ...

Polaris TR28P Le manuel du propriétaire

Marque: Polaris

Modèle: TR28P

Catégorie: Accessoires de piscine hors terre

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Polaris TR28P Owner's manual
español: Polaris TR28P El manual del propietario

Polaris TR28P Le manuel du propriétaire

Polaris TR28P Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents