ASROCK K10N78M PRO Le manuel du propriétaire

11

1

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans-

lated in any language, in any form or by any means, except duplication of documen-

tation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identifica-

tion or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or omissions

that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind,

either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose. In no event shall

ASRock, its directors, officers, employees, or agents be liable for any indirect, special,

incidental, or consequential damages (including damages for loss of profits, loss of

business, loss of data, interruption of business and the like), even if ASRock has been

advised of the possibility of such damages arising from any defect or error in the guide

or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Published July 2009

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic

substance controlled in Perchlorate Best Management Practices (BMP) regulations

passed by the California Legislature. When you discard the Lithium battery in

California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

22

2

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

Motherboard LayoutMotherboard Layout

Motherboard Layout

1 PS2_USB_PW1 Jumper 16 Chassis Speaker Header

2 ATX 12V Power Connector (ATX12V1) (SPEAKER 1, Purple)

3 AM2 940-Pin CPU Socket 17 System Panel Header (PANEL1, Orange)

4 CPU Heatsink Retention Module 18 USB 2.0 Header (USB8_9, Blue)

5 2 x 240-pin DDR2 DIMM Slots 19 USB 2.0 Header (USB6_7, Blue)

(Dual Channel: DDRII_1, DDRII_2; Yellow) 20 Infrared Module Header (IR1)

6 CPU Fan Connector (CPU_FAN1) 21 Print Port Header (LPT1, Purple)

7 ATX Power Connector (ATXPWR1) 22 Floppy Connector (FLOPPY1)

8 Primary IDE Connector (IDE1, Blue) 23 Serial Port Connector (COM1)

9 SATAII Connector (SATAII_2 (PORT 1), Red) 24 Internal Audio Connector: CD1 (Black)

10 SATAII Connector (SATAII_4 (PORT 3), Red) 25 Front Panel Audio Header

11 SATAII Connector (SATAII_1 (PORT 0), Red) (HD_AUDIO1, Lime)

12 SATAII Connector (SATAII_3 (PORT 2), Red) 26 PCI Slots (PCI1- 2)

13 SPI BIOS Chip 27 PCI Express x16 Slot (PCIE2, Green)

14 Clear CMOS Jumper (CLRCMOS1) 28 PCI Express x1 Slot (PCIE1, White)

15 Chassis Fan Connector (CHA_FAN1) 29 NVIDIA GeForce 8100 Chipset

33

3

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

I/O PI/O P

I/O P

anelanel

anel

* To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. Please refer to below steps for the software setting of Multi-Streaming.

For Windows

®

XP:

After restarting your computer, you will find “Mixer” tool on your system. Please select “Mixer

ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or

“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker

and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then

reboot your system.

For Windows

®

Vista

TM

:

After restarting your computer, please double-click “Realtek HD Audio Manager” on the

system tray. Set “Speaker Configuration” to “Quadraphonic” or “Stereo”. Click “Device

advanced settings”, choose “Make front and rear output devices playbacks two different audio

streams simultaneously”, and click “ok”. Then reboot your system.

LAN Port

ACT/LINK

LED

SPEED

LED

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED

indications.

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description

Off No Activity Off 10Mbps connection

Blinking Data Activity Orange 100Mbps connection

Green 1Gbps connection

1 PS/2 Mouse Port (Green) 7 USB 2.0 Ports (USB45)

* 2 LAN RJ-45 Port 8 USB 2.0 Ports (USB23)

3 Line In (Light Blue) 9 VGA/DVI-D Port

4 Line Out (Lime) 10 VGA/D-Sub Port

5 Microphone (Pink) 11 PS/2 Keyboard Port (Purple)

6 USB 2.0 Ports (USB01)

44

4

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

1.1.

1.

IntroductionIntroduction

Introduction

Thank you for purchasing ASRock K10N78M Pro motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It de-

livers excellent performance with robust design conforming to ASRock’s commit-

ment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock website

as well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit

our website for specific information about the model you are using.

www.asrock.com/support/index.asp

1.11.1

1.1

Package ContentsPackage Contents

Package Contents

ASRock K10N78M Pro Motherboard

(Micro ATX Form Factor: 9.6-in x 7.5-in, 24.4 cm x 19.1 cm)

ASRock K10N78M Pro Quick Installation Guide

ASRock K10N78M Pro Support CD

One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable

One Serial ATA (SATA) Data Cables (Optional)

One I/O Panel Shield

55

5

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - Micro ATX Form Factor: 9.6-in x 7.5-in, 24.4 cm x 19.1 cm

CPU - Support for Socket AM2+ / AM2 processors: AMD Phenom

TM

FX / Phenom / Athlon 64 FX / Athlon 64 X2 Dual-Core / Athlon

X2 Dual-Core / Athlon 64 / Sempron

processor

- Support for AM3 processors: AMD Phenom

TM

II X4 / X3 and

Athlon II X4 / X3 / X2 processors

- AMD LIVE!

TM

Ready

- Supports AMD’s Cool ‘n’ Quiet

TM

Technology

- FSB 2600 MHz (5.2 GT/s)

- Supports Untied Overclocking Technology (see CAUTION 1)

- Supports Hyper-Transport 3.0 (HT 3.0) Technology

Chipset - NVIDIA

®

GeForce 8200

Memory - Dual Channel DDR2 Memory Technology (see CAUTION 2)

- 2 x DDR2 DIMM slots

- Support DDR2 1066/800/667/533 non-ECC, un-buffered

memory (see CAUTION 3)

- Max. capacity of system memory: 8GB (see CAUTION 4)

Expansion Slot - 1 x PCI Express 2.0 x16 slot (green @ x16 mode)

- 1 x PCI Express x1 slot

- 2 x PCI slots

- Supports NVIDIA

®

Hybrid SLI

TM

Graphics - Integrated NVIDIA

®

GeForce 8200 graphics

- DX10 VGA, Pixel Shader 4.0

- Max. shared memory 512MB (see CAUTION 5)

- Dual VGA Output: support DVI-D and D-Sub ports by

independent display controllers

- Supports HDCP function with DVI-D port

- Supports Full HD 1080p Blu-ray (BD) / HD-DVD playback with

DVI-D port (see CAUTION 6)

- NVIDIA

®

PureVideo

TM

HD Ready

Audio - 5.1 CH Windows

®

Vista

TM

Premium Level HD Audio

(ALC662 Audio Codec)

- Chipset embeded HDMI Audio

LAN - Gigabit LAN 10/100/1000 Mb/s

- Giga PHY Realtek RTL8211CL

- Supports Wake-On-LAN

Rear Panel I/O I/O Panel

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x VGA/D-Sub Port

66

6

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

- 1 x VGA/DVI-D Port (see CAUTION 7)

- 6 x Ready-to-Use USB 2.0 Ports

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)

- HD Audio Jack: Line in / Front Speaker / Microphone

Connector - 4 x SATAII 3.0Gb/s connectors, support RAID (RAID 0,

RAID 1, RAID 0+1, RAID 5 and JBOD), NCQ, AHCI and “Hot

Plug” functions (see CAUTION 8)

- 1 x ATA133 IDE connector (supports 2 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x Print port header

- 1 x COM port header

- CPU/Chassis FAN connector

- 24 pin ATX power connector

- 4 pin 12V power connector

- CD in header

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

(see CAUTION 9)

BIOS Feature - 8Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- AMBIOS 2.3.1 Support

- Supports Smart BIOS

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)

Unique Feature - ASRock OC Tuner (see CAUTION 10)

- Intelligent Energy Saver (see CAUTION 11)

- Instant Boot

- ASRock Instant Flash (see CAUTION 12)

- Hybrid Booster:

- CPU Frequency Stepless Control (see CAUTION 13)

- ASRock U-COP (see CAUTION 14)

- Boot Failure Guard (B.F.G.)

- ASRock AM2 Boost: ASRock Patented Technology to boost

memory performance up to 12.5% (see CAUTION 15)

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan

77

7

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

CAUTION!

1. This motherboard supports Untied Overclocking Technology. Please read

“Untied Overclocking Technology” on page 29 for details.

2. This motherboard supports Dual Channel Memory Technology. Before

you implement Dual Channel Memory Technology, make sure to read

the installation guide of memory modules on page 13 for proper

installation.

3. Whether 1066MHz memory speed is supported depends on the AM2+

CPU you adopt. If you want to adopt DDR2 1066 memory module on this

motherboard, please refer to the memory support list on our website for

the compatible memory modules.

ASRock website http://www.asrock.com

4. Due to the operating system limitation, the actual memory size may be

less than 4GB for the reservation for system usage under Windows

®

XP

and Windows

®

Vista

TM

. For Windows

®

XP 64-bit and Windows

®

Vista

TM

64-bit with 64-bit CPU, there is no such limitation.

5. The maximum shared memory size is defined by the chipset vendor

and is subject to change. Please check NVIDIA

®

website for the latest

information.

6. 1080p Blu-ray (BD) / HD-DVD playback support on this motherboard re-

quires the proper hardware configuration. Please refer to page 9 and 10 for

the minimum hardware requirement and the passed 1080p Blu-ray (BD) /

HD-DVD films in our lab test.

7. This DVI-D port for the chipset adopted on this motherboard can support

DVI/HDCP and HDMI format signal. You may use the DVI to HDMI adapter to

convert this DVI-D port to HDMI interface. DVI to HDMI adapter is not bundled

with our product, please refer to the adapter vendor for further information.

8. Before installing SATAII hard disk to SATAII connector, please read the “SATAII

Hard Disk Setup Guide” on page 31 of “User Manual” in the support CD to

adjust your SATAII hard disk drive to SATAII mode. You can also connect

SATA hard disk to SATAII connector directly.

WARNING

Please realize that there is a certain risk involved with overclocking, including

adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using

the third-party overclocking tools. Overclocking may affect your system stability, or

even cause damage to the components and devices of your system. It should be

done at your own risk and expense. We are not responsible for possible damage

caused by overclocking.

- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore

OS - Microsoft

®

Windows

®

XP / XP Media Center / XP 64-bit / Vista

TM

/ Vista

TM

64-bit compliant

Certifications - FCC, CE, WHQL

* For detailed product information, please visit our website: http://www.asrock.com

88

8

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

9. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

Vista

TM

64-bit / Vista

TM

/ XP 64-bit / XP SP1 or SP2.

10. It is a user-friendly ASRock overclocking tool which allows you to surveil

your system by hardware monitor function and overclock your hardware

devices to get the best system performance under Windows

®

environment. Please visit our website for the operation procedures of

ASRock OC Tuner. ASRock website: http://www.asrock.com

11. Featuring an advanced proprietary hardware and software design,

Intelligent Energy Saver is a revolutionary technology that delivers

unparalleled power savings. The voltage regulator can reduce the

number of output phases to improve efficiency when the CPU cores are

idle. In other words, it is able to provide exceptional power saving and

improve power efficiency without sacrificing computing performance.

To use Intelligent Energy Saver function, please enable Cool ‘n’ Quiet

option in the BIOS setup in advance. Please visit our website for the

operation procedures of Intelligent Energy Saver.

ASRock website: http://www.asrock.com

12. ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM.

This convenient BIOS update tool allows you to update system BIOS

without entering operating systems first like MS-DOS or Windows

®

. With

this utility, you can press <F6> key during the POST or press <F2> key to

BIOS setup menu to access ASRock Instant Flash. Just launch this tool

and save the new BIOS file to your USB flash drive, floppy disk or hard

drive, then you can update your BIOS only in a few clicks without prepar-

ing an additional floppy diskette or other complicated flash utility. Please

be noted that the USB flash drive or hard drive must use FAT32/16/12 file

system.

13. Although this motherboard offers stepless control, it is not recommended

to perform over-clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU.

14. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

15. This motherboard supports ASRock AM2 Boost overclocking technology for

AM2 CPU. If you enable this function in the BIOS setup, the memory perfor-

mance will improve up to 12.5%, but the effect still depends on the AM2 CPU

you adopt. Enabling this function will overclock the chipset/CPU reference

clock. However, we can not guarantee the system stability for all CPU/DRAM

configurations. If your system is unstable after AM2 Boost function is enabled,

it may not be applicative to your system. You may choose to disable this

function for keeping the stability of your system.

99

9

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

1.31.3

1.3

Minimum Hardware Requirement for 1080p Blu-rayMinimum Hardware Requirement for 1080p Blu-ray

Minimum Hardware Requirement for 1080p Blu-ray

(BD) / HD(BD) / HD

(BD) / HD

-D-D

-D

VD Playback SupporVD Playback Suppor

VD Playback Suppor

tt

t

1080p Blu-ray (BD) / HD-DVD playback support on this motherboard

requires the proper hardware configuration. Please refer to below table

for the minimum hardware requirement.

CPU AMD Athlon X2 4000+

VGA Onboard VGA with DVI-D port

Memory Dual Channel DDR2 667, 1GB x 2

Suggested OS Windows

®

Vista

TM

or Windows

®

Vista

TM

64

* If you need to use CyberLink PowerDVD Ultra version 7.3, we suggest to disable

Hardware Acceleration function for better playback performance and compatibility.

After executing CyberLink PowerDVD Ultra program, please follow below steps to

disable Hardware Acceleration function.

A. Right-click the main page of CyberLink PowerDVD Ultra program.

B. Click “Configuration”.

C. Select “Video”.

D. Click “Enable hardware acceleration (nVidia PureVideo)” to remove the “V” mark

in this item.

E. Click “OK” to save the change.

1010

10

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

1.41.4

1.4

PP

P

assed 1080p Blu-ray (BD) / HDassed 1080p Blu-ray (BD) / HD

assed 1080p Blu-ray (BD) / HD

-D-D

-D

VD FVD F

VD F

ilms in Our Lilms in Our L

ilms in Our L

abab

ab

TT

T

estest

est

DVD Film Name Format Producer

Type

Blu-ray SWORDFISH VC-1 WB

DVD UNDERWORLD EVOLUTION MPEG-2 SONY

X-MEN III MPEG-4-AVC FOX

SPEED MPEG-4-AVC FOX

CASINO ROYALE MPEG-4-AVC SONY

THE LEAGUE OF MPEG-4-AVC FOX

EXTRAORDINARY GENTLEMEN

HD- KING KONG VC-1 UNIVERSAL

DVD NEW ORLEANS CONCERT MPEG-2 WEA

ONE SIX RIGHT MPEG-2 TERWILLIGER

* MPEG-4-AVC mentioned above refers to the same format of H.264.

* Above passed films are tested under below configuration.

Items Configurations

CPU AMD Athlon X2 4000+

VGA Onboard VGA with DVI-D port

Memory Dual Channel DDR2 667, 1GB x 2

OS Windows

®

Vista

TM

or Windows

®

Vista

TM

64

Playback Software CyberLink PowerDVD Ultra

DVD Player Blu-ray-DVDRW-LG-GBW-H10N (BD)

HD DVD-HP-TOSD-H802A-01 (HD-DVD)

1111

11

ASRock K10N78M Pro Motherboard

2.2.

2.

InstallationInstallation

Installation

This is a Micro ATX form factor (9.6-in x 7.5-in, 24.4 cm x 19.1 cm) motherboard.

Before you install the motherboard, study the configuration of your chassis to en-

sure that the motherboard fits into it.

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install motherboard

components or change any motherboard settings.

Before you install or remove any component, ensure that the

power is switched off or the power cord is detached from the

power supply. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

1. Unplug the power cord from the wall socket before touching any

component.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet or

the like. Also remember to use a grounded wrist strap or touch a

safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded anti-

static pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the motherboard

to the chassis, please do not over-tighten the screws! Doing so may

damage the motherboard.

EnglishEnglish

English

1212

12

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90

o

angle.

Step 2. Position the CPU directly above the socket such that the CPU corner with

the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

2.22.2

2.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

Installation of CPU Fan and Heatsink

After you install the CPU into this motherboard, it is necessary to install a

larger heatsink and cooling fan to dissipate heat. You also need to spray

thermal grease between the CPU and the heatsink to improve heat

dissipation. Make sure that the CPU and the heatsink are securely fas-

tened and in good contact with each other. Then connect the CPU fan to

the CPU FAN connector (CPU_FAN1, see Page 2, No. 6). For proper

installation, please kindly refer to the instruction manuals of the CPU fan

and the heatsink.

STEP 1:

Lift Up The Socket Lever

STEP 2 / STEP 3:

Match The CPU Golden Triangle

To The Socket Corner Small

Triangle

STEP 4:

Push Down And Lock

The Socket Lever

Lever 90° Up

CPU Golden Triangle

Socket Corner

Small Triangle

1313

13

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

2.3 Installation of Memory Modules (DIMM)2.3 Installation of Memory Modules (DIMM)

2.3 Installation of Memory Modules (DIMM)

K10N78M Pro motherboard provides two 240-pin DDR2 (Double Data Rate 2) DIMM

slots, and supports Dual Channel Memory Technology. For dual channel configuration,

you always need to install two identical (the same brand, speed, size and chip-

type) memory modules in the DDR2 DIMM slots to activate Dual Channel Memory

Technology. Otherwise, it will operate at single channel mode.

1. It is not allowed to install a DDR memory module into DDR2 slot;

otherwise, this motherboard and DIMM may be damaged.

2. If you install only one memory module or two non-identical memory

modules, it is unable to activate the Dual Channel Memory

Technology.

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

1414

14

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

2.4 Expansion Slots (PCI and PCI Express Slots)2.4 Expansion Slots (PCI and PCI Express Slots)

2.4 Expansion Slots (PCI and PCI Express Slots)

There are 2 PCI slots and 2 PCI Express slots on this motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

PCIE slots: PCIE1 (PCIE x1 slot; White) is used for PCI Express cards with x1 lane

width cards, such as Gigabit LAN card, SATA2 card, etc.

PCIE2 (PCIE x16 slot; Green) is used for PCI Express cards with x16

lane width graphics cards.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in a

chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

1515

15

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

2.52.5

2.5

Hybrid SLIHybrid SLI

Hybrid SLI

TMTM

TM

Operation Guide Operation Guide

Operation Guide

This motherboard supports NVIDIA

®

Hybrid SLI

TM

feature. Hybrid SLI

TM

technology, based

on NVIDIA

®

’ s industry-leading SLI

TM

technology, delivers multi-GPU (graphics processing

unit) benefits when an NVIDIA

®

motherboard GPU is combined with an NVIDIA

®

discrete

GPU. Hybrid SLI

TM

technology today includes two primary features: GeForce

®

Boost

and HybridPower

TM

. Hybrid SLI

TM

increases graphics performance with GeForce

®

Boost

and provides intelligent power management with HybridPower

TM

. Currently, NVIDIA

®

Hybrid

SLI

TM

Technology is only supported with Windows

®

Vista

TM

OS, and is not available with

other OS. Please visit our website for the driver update in the future.

GeForce

®

Boost

GeForce

®

Boost turbocharges the performance of NVIDIA

®

discrete GPU when

combined with NVIDIA

®

motherboard GPU. When GeForce

®

Boost is enabled, the

motherboard GPU and the discrete GPU share the rendering load by rendering

different frames of an image. Installing NVIDIA

®

Hybrid SLI

TM

-enabled graphics card

into NVIDIA

®

Hybrid SLI

TM

-enabled motherboard allows you to enjoy additive

performance.

HybridPower

TM

HybridPower

TM

enables users to switch off the discrete GPU when the higher

processing power of the discrete GPU is not required and use the motherboard

GPU for non intensive graphics applications. Switching off the discrete GPU not

only lowers the total system power consumption for everyday computing tasks like

browsing the Web, word processing, or watching HD videos but also lowers total

system noise.

Minimum System Configuration for Hybrid SLIMinimum System Configuration for Hybrid SLI

Minimum System Configuration for Hybrid SLI

TMTM

TM

For best Hybrid SLI

TM

benefits, the following minimum system configuration is

recommended. Please refer to below table for the minimum system configuration for

GeForce

®

Boost mode and HybridPower

TM

mode.

GeForce

®

Boost

CPU AMD Phenom CPU

Memory Dual Channel DDR2 800, 1024MB x 2

256MB or 512MB shared memory for motherboard GPU

Suggested OS Windows

®

Vista

TM

or Windows

®

Vista

TM

64

HybridPower

TM

CPU AMD Athlon X2 3800+ CPU

Memory Dual Channel DDR2 667, 1024MB x 2

256MB or 512MB shared memory for motherboard GPU

Suggested OS Windows

®

Vista

TM

or Windows

®

Vista

TM

64

1616

16

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

Supported PCI Express Card for Hybrid SLISupported PCI Express Card for Hybrid SLI

Supported PCI Express Card for Hybrid SLI

TMTM

TM

GeForce

®

Boost and HybridPower

TM

features are supported only with certain set of discrete

GPUs. Please refer to our website for the graphics cards update in the future.

Enjoy the benefit of NVIDIAEnjoy the benefit of NVIDIA

Enjoy the benefit of NVIDIA

®®

®

Hybrid SLI Hybrid SLI

Hybrid SLI

TMTM

TM

To enjoy Hybrid SLI

TM

feature, please refer to below installation and setup procedures

according to the mode you plan to use.

A. GeForceA. GeForce

A. GeForce

®®

®

Boost Boost

Boost

Step 1. Install one compatible PCI Express graphics card to PCIE2 slot (green). For

the proper installation procedures, please refer to section “Expansion Slots”.

Step 2. Connect the monitor cable to the correspondent connector on the PCI

Express graphics card on PCIE2 slot.

Step 3. Boot your system. Press <F2> to enter BIOS setup. Enter “Advanced” screen,

and enter “Chipset Settings”. Then set the option “Hybrid SLI” to [256MB] or

[512MB].

For users using single monitor: If you connect the monitor to the

motherboard GPU, you can switch between GeForce

®

Boost mode (Boost

Performance) and HybridPower

TM

mode (Save Power). If you connect the

monitor to the card GPU, you can choose GeForce

®

Boost mode (Boost

Performance) only.

If you want to use onboard VGA output, after step 1 to 3, please follow

below steps:

A. Set up the BIOS option “Primary Graphics Display” to [Onboard], and

save your BIOS change and exit BIOS setup.

B. Power off your system.

C. Switch your monitor cable to the connector on the I/O shield.

After reboot your system, you are allowed to switch between GeForce

®

Boost mode (Boost Performance) and HybridPower

TM

mode (Save

Power) according to your request.

For GeForce

®

Boost

Vendor Chipset Model Driver

NVIDIA GeForce 8400GS Gigabyte GV-NX84G256H 174.83

GeForce 8400GS Foxconn FV-N84SM2DT 174.83

GeForce 8400GS Leadtek WinFast PX8400 GS TDH 174.83

GeForce 8500GT Gigabyte GV-NX85T256H 174.83

For HybridPower

TM

Vendor Chipset Model Driver

NVIDIA GeForce 9800GX2 ASUS PCIE-ASUS-9800GX2/512M174.83

1717

17

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

B. HybridPowerB. HybridPower

B. HybridPower

TMTM

TM

Step 1. Install one compatible PCI Express graphics card to PCIE2 slot (green). For

the proper installation procedures, please refer to section “Expansion Slots”.

Step 2. Boot your system. Press <F2> to enter BIOS setup. Enter “Advanced” screen,

and enter “Chipset Settings”. Then set the option “Hybrid SLI” to [256MB] or

[512MB]. And set the option “Primary Graphics Display” to [Onboard].

Step 3. Save your BIOS change and exit BIOS setup.

Step 4. Power off your system.

Step 5. Connect the monitor cable to the correspondent connector on the I/O shield.

Step 6. Boot into OS. Install Hybrid SLI

TM

driver from our support CD to your system.

Hybrid SLI

TM

driver is in the following path of ASRock support CD:

(There are two ASRock support CD in the motherboard gift box pack, please

choose the one for Windows

®

Vista

TM

/ Vista

TM

64-bit.)

..\Drivers\Hybrid SLI driver\Vista

* Currently, Hybrid SLI

TM

driver only has Vista

TM

32 version, please visit our

website for future update.

Step 7. Restart your computer. Then you will find the Hybrid icon on your Windows

®

taskbar. Please click the icon and select the item “Save Power”.

Step 4. Boot into OS. Install Hybrid SLI

TM

driver from our support CD to your system.

Hybrid SLI

TM

driver is in the following path of ASRock support CD:

(There are two ASRock support CD in the motherboard gift box pack, please

choose the one for Windows

®

Vista

TM

/ Vista

TM

64-bit.)

..\Drivers\Hybrid SLI driver\Vista

* Currently, Hybrid SLI

TM

driver only has Vista

TM

32 version, please visit our

website for future update.

Step 5. Restart your computer. Then you will find the Hybrid icon on your Windows

®

taskbar.

Step 6. The default setting is GeForce

®

Boost mode (Boost Performance). You do not

need to adjust the setup anymore.

1818

18

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

C. Dual MonitorsC. Dual Monitors

C. Dual Monitors

Step 1. Install one compatible PCI Express graphics card to PCIE2 slot (green). For

the proper installation procedures, please refer to section “Expansion Slots”.

Step 2. Boot your system. Press <F2> to enter BIOS setup. Enter “Advanced” screen,

and enter “Chipset Settings”. Then set the option “Share Memory” to [32MB],

[64MB], [128MB], [256MB] or [512MB].

Step 3. Connect one monitor cable to the correspondent connector on the I/O shield.

Connect the other monitor cable to the correspondent connector on the PCI

Express graphics card on PCIE2 slot.

Step 4. Boot into OS. Install Hybrid SLI

TM

driver from our support CD to your system.

Hybrid SLI

TM

driver is in the following path of ASRock support CD:

(There are two ASRock support CD in the motherboard gift box pack, please

choose the one for Windows

®

Vista

TM

/ Vista

TM

64-bit.)

..\Drivers\Hybrid SLI driver\Vista

* Currently, Hybrid SLI

TM

driver only has Vista

TM

32 version, please visit our

website for future update.

Step 5. Restart your computer. Then you will find the Hybrid icon on your Windows

®

taskbar. Please click the icon and select the item “Additional Displays”.

Step 6. Click the desktop. Then your system is switched to Dual Monitors mode

(Additional Displays).

Step 8. Click the desktop. Then your system is switched to HybridPower

TM

mode

(Save Power).

1919

19

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

VGA/D-Sub port

2.6 Dual Monitor and Surround Display Features2.6 Dual Monitor and Surround Display Features

2.6 Dual Monitor and Surround Display Features

Dual Monitor Feature

This motherboard supports dual monitor feature. With the internal dual VGA output

support (DVI-D and D-Sub), you can easily enjoy the benefits of dual monitor feature

without installing any add-on VGA card to this motherboard. This motherboard also

provides independent display controllers for DVI-D and D-Sub to support dual VGA

output so that DVI-D and D-sub can drive same or different display contents. To enable

dual monitor feature, please follow the below steps:

1. Connect the DVI-D monitor cable to the VGA/DVI-D port on the I/O panel of this

motherboard. Connect the D-Sub monitor cable to the VGA/D-Sub port on the I/O

panel of this motherboard.

2. If you have installed onboard VGA driver from our support CD to your system

already, you can freely enjoy the benefits of dual monitor function provided by

VGA/DVI-D and VGA/D-Sub ports with this motherboard after your system

boots. If you haven’t installed onboard VGA driver yet, please install onboard

VGA driver from our support CD to your system and restart your computer.

Then you can start to use dual monitor function provided by VGA/DVI-D and

VGA/D-Sub ports with this motherboard.

1. When you playback HDCP-protected video from Blu-ray (BD) or

HD-DVD disc, the content will be displayed only in one of the two

monitors instead of both monitors.

2. This motherboard does not support dual monitor feature under DOS

because in this situation, the VGA/DVI-D output is not available. There

is no such limitation under Windows

®

OS.

VGA/DVI-D port

2020

20

ASRock K10N78M Pro Motherboard

EnglishEnglish

English

Surround Display Feature

This motherboard supports surround display upgrade. With the internal dual VGA

output support (DVI-D and D-Sub) and the external add-on PCI Express VGA card, you

can easily enjoy the benefits of surround display feature. Please refer to the following

steps to set up a surround display environment:

1. Install the NVIDIA

®

PCI Express VGA card to PCI Express slot. Please refer to

page 14 for proper expansion card installation procedures for details.

2. Connect the DVI-D monitor cable to the VGA/DVI-D port on the I/O panel of this

motherboard. Connect the D-Sub monitor cable to the VGA/D-Sub port on the I/O

panel of this motherboard. And connect the other monitor cables to the correspond-

ing connectors of the add-on PCI Express VGA cards on PCIE2 slot.

3. Boot your system. Press <F2> to enter BIOS setup. Enter “Share Memory”

option to adjust the memory capability to [32MB], [64MB], [128MB], [256MB] or

[512MB] to enable the function of VGA/D-sub. Please make sure that the value

you select is less than the total capability of the system memory. If you do not

adjust the BIOS setup, the default value of “Share Memory”, [Auto], will disable

VGA/D-Sub function when the add-on VGA card is inserted to this

motherboard.

4. Install the onboard VGA driver and the add-on PCI Express VGA card driver to

your system. If you have installed the onboard VGA driver and the add-on PCI

Express VGA card driver already, there is no need to install them again.

5. Set up a multi-monitor display.

For Windows

®

XP / XP 64-bit OS:

Right click the desktop, choose “Properties”, and select the “Settings” tab

so that you can adjust the parameters of the multi-monitor according to the

steps below.

A. Click the “Identify” button to display a large number on each monitor.

B. Right-click the display icon in the Display Properties dialog that you wish

to be your primary monitor, and then select “Primary”. When you use

multiple monitors with your card, one monitor will always be Primary,

and all additional monitors will be designated as Secondary.

C. Select the display icon identified by the number 2.

D. Click “Extend my Windows desktop onto this monitor”.

E. Right-click the display icon and select “Attached”, if necessary.

F. Set the “Screen Resolution” and “Color Quality” as appropriate for the

second monitor. Click “Apply” or “OK” to apply these new values.

G. Repeat steps C through E for the diaplay icon identified by the number

one, two, three and four.

For Windows

®

Vista

TM

/ Vista

TM

64-bit OS:

Right click the desktop, choose “Personalize”, and select the “Display

Settings” tab so that you can adjust the parameters of the multi-monitor

according to the steps below.

La page charge ...

ASROCK K10N78M PRO Le manuel du propriétaire

ASROCK K10N78M PRO Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents