ASROCK K10N78HSLI-GLAN Le manuel du propriétaire

11

1

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans-

lated in any language, in any form or by any means, except duplication of documen-

tation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identifica-

tion or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or omissions

that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind,

either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose. In no event shall

ASRock, its directors, officers, employees, or agents be liable for any indirect, special,

incidental, or consequential damages (including damages for loss of profits, loss of

business, loss of data, interruption of business and the like), even if ASRock has been

advised of the possibility of such damages arising from any defect or error in the guide

or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Published April 2008

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic

substance controlled in Perchlorate Best Management Practices (BMP) regulations

passed by the California Legislature. When you discard the Lithium battery in

California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

22

2

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PW1 Jumper 18 SATAII Connector (SATAII_3 (PORT2))

2 ATX 12V Power Connector (ATX12V1) 19 NVIDIA GeForce 8200 Chipset

3 CPU Fan Connector (CPU_FAN1) 20 System Panel Header (PANEL1)

4 CPU Heatsink Retention Module 21 Chassis Speaker Header (SPEAKER 1)

5 AM2 940-Pin CPU Socket 22 Chassis Fan Connector (CHA_FAN1)

6 2 x 240-pin DDR2 DIMM Slots 23 Floppy Connector (FLOPPY1)

(Dual Channel A: DDRII_1, DDRII_2; Yellow) 24 DeskExpress Hot Plug Detection Header

7 2 x 240-pin DDR2 DIMM Slots (IR1)

(Dual Channel B: DDRII_3, DDRII_4; Orange) 25 Internal Audio Connector: CD1 (Black)

8 Primary IDE Connector (IDE1, Blue) 26 Front Panel Audio Header (HD_AUDIO1)

9 Clear CMOS Jumper (CLRCMOS1) 27 WiFi/E Header (WIFI/E)

10 SATAII Connector (SATAII_5 (PORT4)) 28 PCI Slots (PCI1- 3)

11 SATAII Connector (SATAII_6 (PORT5)) 29 HDMI_SPDIF Header (HDMI_SPDIF1)

12 SATAII Connector (SATAII_4 (PORT3)) 30 PCI Express x1 Slot (PCIE3, White)

13 SATAII Connector (SATAII_2 (PORT1)) 31 PCI Express x1 Slot (PCIE2, White)

14 USB 2.0 Header (USB8_9, Blue) 32 PCI Express x16 Slot (PCIE1, Green)

15 USB 2.0 Header (USB6_7, Blue) 33 ATX Power Connector (ATXPWR1)

16 SATAII Connector (SATAII_1 (PORT0)) 34 COM Port Header (COM1)

17 SPI BIOS Chip 35 eSATAII Connector (eSATAII_TOP)

33

3

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

ASRASR

ASR

ock eSock eS

ock eS

AA

A

TT

T

AII_SPDIF I/OAII_SPDIF I/O

AII_SPDIF I/O

* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.

See the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

1 PS/2 Mouse Port (Green) 8 USB 2.0 Ports (USB01)

2 LAN RJ-45 Port 9 USB 2.0 Ports (USB23)

3 Rear Speaker (Black) 10 USB 2.0 Ports (USB45)

4 Central / Bass (Orange) 11 eSATAII Port

5 Line In (Light Blue) 12 Optical SPDIF Out Port

*6 Front Speaker (Lime) 13 Coaxial SPDIF Out Port

7 Microphone (Pink) 14 PS/2 Keyboard Port (Purple)

* To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. Please refer to below steps for the software setting of Multi-Streaming.

For Windows

®

XP:

After restarting your computer, you will find “Mixer” tool on your system. Please select “Mixer

ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or

“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker

and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then

reboot your system.

For Windows

®

Vista

TM

:

After restarting your computer, please double-click “Realtek HD Audio Manager” on the

system tray. Set “Speaker Configuration” to “5.1 Speaker”. Click “Device advanced settings”,

choose “Make front and rear output devices playbacks two different audio streams

simultaneously”, and click “ok”. Then reboot your system.

Audio Output Channels Front Speaker Rear Speaker Central / Bass

(No. 6) (No. 3) (No. 4)

2 V -- --

4VV--

6VVV

44

4

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

1.1.

1.

IntroductionIntroduction

Introduction

Thank you for purchasing ASRock K10N78hSLI-GLAN motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It delivers

excellent performance with robust design conforming to ASRock’s commitment to qual-

ity and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock website

as well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit

our website for specific information about the model you are using.

www.asrock.com/support/index.asp

1.11.1

1.1

PP

P

ackack

ack

age Contentsage Contents

age Contents

ASRock K10N78hSLI-GLAN Motherboard

(ATX Form Factor: 12.0-in x 8.4-in, 30.5 cm x 21.3 cm)

ASRock K10N78hSLI-GLAN Quick Installation Guide

ASRock K10N78hSLI-GLAN Support CD

One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

Two Serial ATA (SATA) Data Cables (Optional)

One Serial ATA (SATA) HDD Power Cable (Optional)

One HDMI_SPDIF Cable (Optional)

One “ASRock eSATAII_SPDIF I/O” I/O Panel Shield

55

5

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - ATX Form Factor: 12.0-in x 8.4-in, 30.5 cm x 21.3 cm

CPU - Support for Socket AM2+ / AM2 processors: AMD Phenom

TM

FX / Phenom / Athlon 64 FX / Athlon 64 X2 Dual-Core / Athlon

X2 Dual-Core / Athlon 64 / Sempron

processor

- AMD LIVE!

TM

Ready

- Supports AMD’s Cool ‘n’ Quiet

TM

Technology

- FSB 2600 MHz (5.2 GT/s) (see CAUTION 1)

- Supports Untied Overclocking Technology (see CAUTION 2)

- Supports Hyper-Transport 3.0 (HT 3.0) Technology

Chipset - NVIDIA

®

GeForce 8200

Memory - Dual Channel DDR2 Memory Technology (see CAUTION 3)

- 4 x DDR2 DIMM slots

- Support DDR2 1066/800/667/533 non-ECC, un-buffered memory

(see CAUTION 4)

- Max. capacity of system memory: 8GB (see CAUTION 5)

Expansion Slot - 1 x PCI Express 2.0 x16 slot (green @ x16 mode)

- 2 x PCI Express x1 slots

- 3 x PCI slots

- Supports NVIDIA

®

Hybrid SLI

TM

Geforce

®

Boost feature

(see CAUTION 6)

Audio - 5.1 CH Windows

®

Vista

TM

Premium Level HD Audio

(ALC662 Audio Codec)

LAN - Gigabit LAN 10/100/1000 Mb/s

- Giga PHY Realtek RTL8211B

- Supports Wake-On-LAN

Rear Panel I/O ASRock eSATAII_SPDIF I/O

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Coaxial SPDIF Out Port

- 1 x Optical SPDIF Out Port

- 6 x Ready-to-Use USB 2.0 Ports

- 1 x eSATAII Port

- 1 x RJ-45 LAN Port

- HD Audio Jack: Rear Speaker/Central/Bass/Line in/Front

Speaker/Microphone (see CAUTION 7)

Connector - 6 x SATAII 3.0Gb/s connectors, support RAID (RAID 0, RAID 1,

RAID 0+1, JBOD and RAID 5), NCQ, AHCI and “Hot Plug”

functions (see CAUTION 8)

66

6

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

- 1 x eSATAII 3.0Gb/s connector (shared with 1 SATAII

connector) (see CAUTION 9)

- 1 x ATA133 IDE connector (supports 2 x IDE devices)

- 1 x Floppy connector

- 1 x DeskExpress Hot Plug Detection header

- 1 x COM port header

- 1 x HDMI_SPDIF header

- CPU/Chassis FAN connector

- 24 pin ATX power connector

- 4 pin 12V power connector

- CD in header

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

(see CAUTION 10)

- 1 x WiFi/E header (see CAUTION 11)

BIOS Feature - 4Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- AMBIOS 2.3.1 Support

- CPU, DRAM, Chipset Core, HTT Voltage Multi-adjustment

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)

Unique Feature - ASRock OC Tuner (see CAUTION 12)

- Intelligent Energy Saver (see CAUTION 13)

- Hybrid Booster:

- CPU Frequency Stepless Control (see CAUTION 14)

- ASRock U-COP (see CAUTION 15)

- Boot Failure Guard (B.F.G.)

- ASRock AM2 Boost: ASRock Patented Technology to boost

memory performance up to 12.5% (see CAUTION 16)

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore

OS - Microsoft

®

Windows

®

XP / XP Media Center / XP 64-bit / Vista

TM

/ Vista

TM

64-bit compliant

Certifications - FCC, CE, WHQL

* For detailed product information, please visit our website: http://www.asrock.com

77

7

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

CAUTION!

1. If you install AM2 CPU on this motherbord, the system bus speed will be

HT1.0 (2000 MT/s). If you install AM2+ CPU on this motherbord, the system

bus speed will be HT3.0 (up to 5200 MT/s), and the HT Link frequency

depends on the ability of the AM2+ CPU you adopt. Please refer to the CPU

support list on our website for more information.

ASRock website http://www.asrock.com

2. This motherboard supports Untied Overclocking Technology. Please read

“Untied Overclocking Technology” on page 28 for details.

3. This motherboard supports Dual Channel Memory Technology. Before

you implement Dual Channel Memory Technology, make sure to read

the installation guide of memory modules on page 12 for proper

installation.

4. Whether 1066MHz memory speed is supported depends on the AM2+

CPU you adopt. If you want to adopt DDR2 1066 memory module on this

motherboard, please refer to the memory support list on our website for

the compatible memory modules.

ASRock website http://www.asrock.com

5. Due to the operating system limitation, the actual memory size may be

less than 4GB for the reservation for system usage under Windows

®

XP

and Windows

®

Vista

TM

. For Windows

®

XP 64-bit and Windows

®

Vista

TM

64-bit with 64-bit CPU, there is no such limitation.

6. Hybrid SLI

TM

feature should depend on the driver from NVIDIA

®

and it may

be updated in the future. As long as we have the latest Hybrid SLI

TM

driver,

we will update it to our website. Please visit our website for the updated

Hybrid SLI

TM

driver in the future. For the operation procedures, please refer

to “Hybrid SLI

TM

Operation Guide” on page 15.

7. For microphone input, this motherboard supports both stereo and mono

modes. For audio output, this motherboard supports 2-channel, 4-channel

and 6-channel modes. Please check the table on page 3 for proper

connection.

8. Before installing SATAII hard disk to SATAII connector, please read the “SATAII

Hard Disk Setup Guide” on page 30 of “User Manual” in the support CD to

adjust your SATAII hard disk drive to SATAII mode. You can also connect

SATA hard disk to SATAII connector directly.

9. This motherboard supports eSATAII interface, the external SATAII

specification. Please read “eSATAII Interface Introduction” on page 23

for details about eSATAII and eSATAII installation procedures.

WARNING

Please realize that there is a certain risk involved with overclocking, including

adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using

the third-party overclocking tools. Overclocking may affect your system stability, or

even cause damage to the components and devices of your system. It should be

done at your own risk and expense. We are not responsible for possible damage

caused by overclocking.

88

8

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

10. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

Vista

TM

64-bit / Vista

TM

/ XP 64-bit / XP SP1 or SP2.

11. WiFi/E header supports WiFi+AP function with ASRock WiFi-802.11g or

WiFi-802.11n module, an easy-to-use wireless local area network

(WLAN) adapter. It allows you to create a wireless environment and

enjoy the convenience of wireless network connectivity. Please visit our

website for the availability of ASRock WiFi-802.11g or WiFi-802.11n

module. ASRock website http://www.asrock.com

12. It is a user-friendly ASRock overclocking tool which allows you to surveil

your system by hardware monitor function and overclock your hardware

devices to get the best system performance under Windows

®

environment. Please visit our website for the operation procedures of

ASRock OC Tuner. ASRock website: http://www.asrock.com

13. Featuring an advanced proprietary hardware and software design,

Intelligent Energy Saver is a revolutionary technology that delivers

unparalleled power savings. The voltage regulator can reduce the

number of output phases to improve efficiency when the CPU cores are

idle. In other words, it is able to provide exceptional power saving and

improve power efficiency without sacrificing computing performance.

To use Intelligent Energy Saver function, please enable Cool ‘n’ Quiet

option in the BIOS setup in advance. Please visit our website for the

operation procedures of Intelligent Energy Saver.

ASRock website:

http://www.asrock.com

14. Although this motherboard offers stepless control, it is not recom-

mended to perform over-clocking. Frequencies other than the recom-

mended CPU bus frequencies may cause the instability of the system

or damage the CPU.

15. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC

system.

16. This motherboard supports ASRock AM2 Boost overclocking technology

for AM2 CPU. If you enable this function in the BIOS setup, the memory

performance will improve up to 12.5%, but the effect still depends on the

AM2 CPU you adopt. Enabling this function will overclock the chipset/CPU

reference clock. However, we can not guarantee the system stability for all

CPU/DRAM configurations. If your system is unstable after AM2 Boost func-

tion is enabled, it may not be applicative to your system. You may choose to

disable this function for keeping the stability of your system.

99

9

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

1.31.3

1.3

Minimum Hardware RMinimum Hardware R

Minimum Hardware R

equirement Tequirement T

equirement T

able for Wable for W

able for W

indowsindows

indows

®®

®

VistaVista

Vista

TMTM

TM

Premium 2008 and Basic Logo Premium 2008 and Basic Logo

Premium 2008 and Basic Logo

For system integrators and users who purchase this motherboard and

plan to submit Windows

®

Vista

TM

Premium 2008 and Basic logo, please follow

below table for minimum hardware requirement.

CPU Sempron 2800+

Memory 1GB system memory (Premium)

512MB system memory (Basic)

VGA DX10 with WDDM Driver

with 128bit VGA memory (Premium)

with 64bit VGA memory (Basic)

* After June 1, 2008, all Windows

®

Vista

TM

systems are required to meet above

minimum hardware requirements in order to qualify for Windows

®

Vista

TM

Premium

2008 logo.

1010

10

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

2.2.

2.

InstallationInstallation

Installation

This is an ATX form factor (12.0-in x 8.4-in, 30.5 cm x 21.3 cm) motherboard.

Before you install the motherboard, study the configuration of your chassis to en-

sure that the motherboard fits into it.

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install motherboard

components or change any motherboard settings.

Before you install or remove any component, ensure that the

power is switched off or the power cord is detached from the

power supply. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

1. Unplug the power cord from the wall socket before touching any

component.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet or

the like. Also remember to use a grounded wrist strap or touch a

safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded anti-

static pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the motherboard

to the chassis, please do not over-tighten the screws! Doing so may

damage the motherboard.

1111

11

ASRock K10N78hSLI-GLAN Motherboard

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90

o

angle.

Step 2. Position the CPU directly above the socket such that the CPU corner with

the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

2.22.2

2.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

Installation of CPU Fan and Heatsink

After you install the CPU into this motherboard, it is necessary to install a

larger heatsink and cooling fan to dissipate heat. You also need to spray

thermal grease between the CPU and the heatsink to improve heat

dissipation. Make sure that the CPU and the heatsink are securely fas-

tened and in good contact with each other. Then connect the CPU fan to

the CPU FAN connector (CPU_FAN1, see Page 2, No. 3). For proper

installation, please kindly refer to the instruction manuals of the CPU fan

and the heatsink.

STEP 1:

Lift Up The Socket Lever

STEP 2 / STEP 3:

Match The CPU Golden Triangle

To The Socket Corner Small

Triangle

STEP 4:

Push Down And Lock

The Socket Lever

EnglishEnglish

English

Lever 90° Up

CPU Golden Triangle

Socket Corner

Small Triangle

1212

12

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

2.3 Installation of Memor2.3 Installation of Memor

2.3 Installation of Memor

y Modules (DIMM)y Modules (DIMM)

y Modules (DIMM)

This motherboard provides four 240-pin DDR2 (Double Data Rate 2) DIMM slots,

and supports Dual Channel Memory Technology. For dual channel configuration,

you always need to install identical (the same brand, speed, size and chip-type)

DDR2 DIMM pair in the slots of the same color. In other words, you have to install

identical DDR2 DIMM pair in Dual Channel A (DDRII_1 and DDRII_2; Yellow slots;

see p.2 No.6) or identical DDR2 DIMM pair in Dual Channel B (DDRII_3 and

DDRII_4; Orange slots; see p.2 No.7), so that Dual Channel Memory Technology

can be activated. This motherboard also allows you to install four DDR2 DIMMs for

dual channel configuration, and please install identical DDR2 DIMMs in all four

slots. You may refer to the Dual Channel Memory Configuration Table below.

Dual Channel Memory Configurations

DDRII_1 DDRII_2 DDRII_3 DDRII_4

(Yellow Slot) (Yellow Slot) (Orange Slot) (Orange Slot)

(1) Populated Populated - -

(2) - - Populated Populated

(3)* Populated Populated Populated Populated

* For the configuration (3), please install identical DDR2 DIMMs in all four slots.

1. If you want to install two memory modules, for optimal compatibil-

ity and reliability, it is recommended to install them in the slots of

the same color. In other words, install them either in the set of

yellow slots (DDRII_1 and DDRII_2), or in the set of orange slots

(DDRII_3 and DDRII_4).

2. If only one memory module or three memory modules are in-

stalled in the DDR2 DIMM slots on this motherboard, it is unable to

activate the Dual Channel Memory Technology.

3. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in

DDRII_1 and DDRII_3, it is unable to activate the Dual Channel

Memory Technology .

4. It is not allowed to install a DDR memory module into DDR2 slot;

otherwise, this motherboard and DIMM may be damaged.

1313

13

ASRock K10N78hSLI-GLAN Motherboard

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

EnglishEnglish

English

1414

14

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

2.4 Expansion Slots (PCI and PCI Express Slots)2.4 Expansion Slots (PCI and PCI Express Slots)

2.4 Expansion Slots (PCI and PCI Express Slots)

There are 3 PCI slots and 3 PCI Express slots on this motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

PCIE slots: PCIE1 (PCIE x16 slot; Green) is used for PCI Express cards with x16

lane width graphics cards.

PCIE2 / PCIE3 (PCIE x1 slot; White) is used for PCI Express cards with

x1 lane width cards, such as Gigabit LAN card, SATA2 card and ASRock

PCIE_DE card.

If you want to use ASRock DeskExpress function on this motherboard,

please install ASRock PCIE_DE card on PCIE3 slot.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in a

chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

1515

15

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

2.52.5

2.5

Hybrid SLIHybrid SLI

Hybrid SLI

TMTM

TM

Operation Guide Operation Guide

Operation Guide

This motherboard supports NVIDIA

®

Hybrid SLI

TM

feature. Hybrid SLI

TM

technology, based

on NVIDIA

®

’ s industry-leading SLI

TM

technology, delivers multi-GPU (graphics processing

unit) benefits when an NVIDIA

®

motherboard GPU is combined with an NVIDIA

®

discrete

GPU. Hybrid SLI

TM

technology today includes two primary features: GeForce

®

Boost

and HybridPower

TM

. This motherboard is compatible with GeForce

®

Boost feature in

Hybrid SLI

TM

, which can increase graphics performance. Currently, NVIDIA

®

Hybrid SLI

TM

Technology is only supported with Windows

®

Vista

TM

OS, and is not available with other

OS. Please visit our website for the driver update in the future.

GeForce

®

Boost

GeForce

®

Boost turbocharges the performance of NVIDIA

®

discrete GPU when

combined with NVIDIA

®

motherboard GPU. When GeForce

®

Boost is enabled, the

motherboard GPU and the discrete GPU share the rendering load by rendering

different frames of an image. Installing NVIDIA

®

Hybrid SLI

TM

-enabled graphics card

into NVIDIA

®

Hybrid SLI

TM

-enabled motherboard allows you to enjoy additive

performance.

Minimum System Configuration for Hybrid SLIMinimum System Configuration for Hybrid SLI

Minimum System Configuration for Hybrid SLI

TMTM

TM

For best Hybrid SLI

TM

benefits, the following minimum system configuration is

recommended. Please refer to below table for the minimum system configuration for

GeForce

®

Boost mode.

CPU AMD Phenom CPU

Memory Dual Channel DDR2 800, 1024MB x 2

256MB or 512MB shared memory for motherboard GPU

Suggested OS Windows

®

Vista

TM

or Windows

®

Vista

TM

64

Supported PCI Express Card for Hybrid SLISupported PCI Express Card for Hybrid SLI

Supported PCI Express Card for Hybrid SLI

TMTM

TM

GeForce

®

Boost feature is supported only with certain set of discrete GPUs. Please

refer to our website for the graphics cards update in the future.

Vendor Chipset Model Driver

NVIDIA GeForce 8400GS Gigabyte GV-NX84G256H 174.91

GeForce 8400GS Foxconn FV-N84SM2DT 174.91

GeForce 8400GS Leadtek WinFast PX8400 GS TDH 174.91

GeForce 8500GT Gigabyte GV-NX85T256H 174.91

1616

16

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

Enjoy the benefit of NVIDIAEnjoy the benefit of NVIDIA

Enjoy the benefit of NVIDIA

®®

®

Hybrid SLI Hybrid SLI

Hybrid SLI

TMTM

TM

To enjoy Hybrid SLI

TM

feature, please refer to below installation and setup procedures.

Step 1. Install one compatible PCI Express graphics card to PCIE1 slot (green). For

the proper installation procedures, please refer to section “Expansion Slots”.

Step 2. Connect the monitor cable to the correspondent connector on the PCI

Express graphics card on PCIE1 slot.

Step 3. Boot your system. Press <F2> to enter BIOS setup. Enter “Advanced” screen,

and enter “Chipset Settings”. Then set the option “Hybrid SLI” to [Auto] or

[Chipset Default].

Step 4. Boot into OS. Install Hybrid SLI

TM

driver from our support CD to your system.

Hybrid SLI

TM

driver is in the following path of ASRock support CD:

(There are two ASRock support CD in the motherboard gift box pack, please

choose the one for Windows

®

Vista

TM

/ Vista

TM

64-bit.)

..\Drivers\Hybrid SLI driver\nVIDIA\Vista(174.91) (For Windows

®

Vista

TM

OS)

..\Drivers\Hybrid SLI driver\nVIDIA\Vista64(174.91) (For Windows

®

Vista

TM

64-bit OS)

Step 5. Restart your computer. Then you will find the Hybrid icon on your Windows

®

taskbar.

Step 6. The default setting is GeForce

®

Boost mode (Boost Performance). You do not

need to adjust the setup anymore.

NOTE

If you click the Hybrid icon on the Windows

®

task bar, you are allowed to select your

required Hybrid SLI

TM

mode. However, since this motherboard only support

GeForce

®

Boost mode (Boost Performance), please do not select the options

(“Save Power” and “Additional Displays”) other than “Boost Performance”.

1717

17

ASRock K10N78hSLI-GLAN Motherboard

OpenShort

Clear CMOSDefault

EnglishEnglish

English

2.62.6

2.6

Jumpers SetupJumpers Setup

Jumpers Setup

The illustration shows how jumpers are setup.

When the jumper cap is placed on pins, the

jumper is “Short”. If no jumper cap is placed on

pins, the jumper is “Open”. The illustration

shows a 3-pin jumper whose pin1 and

pin2 are “Short” when jumper cap is placed on

these 2 pins.

Jumper Setting

PS2_USB_PW1 Short pin2, pin3 to enable

(see p.2, No. 1) +5VSB (standby) for PS/2 or

USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

Clear CMOS Jumper

(CLRCMOS1)

(see p.2, No. 9)

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power supply.

After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1

for 5 seconds. However, please do not clear the CMOS right after you update the

BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you

must boot up the system first, and then shut it down before you do the clear-

CMOS action.

1818

18

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

the red-striped side to

Pin1

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

2.7 Onboard Headers and Connectors2.7 Onboard Headers and Connectors

2.7 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper

caps over the headers and connectors will cause permanent dam-

age of the motherboard!

•

Floppy Connector

(33-pin FLOPPY1)

(see p.2, No. 23)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE connector (Blue)

(39-pin IDE1, see p.2, No. 8)

Note: Please refer to the instruction of your IDE device vendor for the details.

Serial ATA II Connectors These six Serial ATAII

(SATAII_1 (PORT0): (SATAII) connectors support

see p.2, No. 16) SATA data cables for internal

(SATAII_2 (PORT1): storage devices. The current

see p.2, No. 13) SATAII interface allows up to

(SATAII_3 (PORT2): 3.0 Gb/s data transfer rate.

see p.2, No. 18)

(SATAII_4 (PORT3):

see p.2, No. 12)

(SATAII_5 (PORT4):

see p.2, No. 10)

(SATAII_6 (PORT5):

see p.2, No. 11)

SATAII_6 (PORT5) connector can be used for internal storage device

or be connected to eSATAII connector to support eSATAII device.

Please read “eSATAII Interface Introduction” on page 23 for details

about eSATAII and eSATAII installation procedures.

SATAII_1 SATAII_3 SATAII_5

(PORT0) (PORT2) (PORT4)

SATAII_2 SATAII_4 SATAII_6

(PORT1) (PORT3) (PORT5)

1919

19

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

eSATAII_TOP

eSATAII Connector This eSATAII connector

(eSATAII_TOP: see p.2, No. 35) supports SATA data cable for

external SATAII function. The

current eSATAII interface

allows up to 3.0 Gb/s data

transfer rate.

USB 2.0 Headers Besides six default USB 2.0

(9-pin USB8_9) ports on the I/O panel, there are

(see p.2 No. 14) two USB 2.0 headers on this

motherboard. Each USB 2.0

header can support two USB

2.0 ports.

(9-pin USB6_7)

(see p.2 No. 15)

WiFi/E Header This header supports WiFi+AP

(15-pin WIFI/E) function with ASRock

(see p.2 No. 27) WiFi-802.11g or WiFi-802.11n

module, an easy-to-use wireless

local area network (WLAN)

adapter. It allows you to create a

wireless environment and enjoy the

convenience of wireless network

connectivity.

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA /

(Optional) SATAII hard disk or the SATAII

connector on this motherboard.

You can also use the SATA data

cable to connect SATAII_6

(PORT5) connector and eSATAII

connector.

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

connect to

the power

supply

connect to the SATA

HDD power connector

2020

20

ASRock K10N78hSLI-GLAN Motherboard

EnglishEnglish

English

DeskExpress Hot Plug Detection This header supports the Hot

Header Plug detection function for

(5-pin IR1) ASRock DeskExpress.

(see p.2 No. 24)

Internal Audio Connectors This connector allows you

(4-pin CD1) to receive stereo audio input

(CD1: see p.2, No. 25) from sound sources such as

a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

Front Panel Audio Header This is an interface for the front

(9-pin HD_AUDIO1) panel audio cable that allows

(see p.2, No. 26) convenient connection and

control of audio devices.

1. High Definition Audio supports Jack Sensing, but the panel wire on

the chassis must support HDA to function correctly. Please follow the

instruction in our manual and chassis manual to install your system.

2. If you use AC’97 audio panel, please install it to the front panel audio

header as below:

A. Connect Mic_IN (MIC) to MIC2_L.

B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C. Connect Ground (GND) to Ground (GND).

D. MIC_RET and OUT_RET are for HD audio panel only. You don’t

need to connect them for AC’97 audio panel.

E. Enter BIOS Setup Utility. Enter Advanced Settings, and then select

Chipset Configuration. Set the Front Panel Control option from

[Auto] to [Enabled].

F. Enter Windows system. Click the icon on the lower right hand

taskbar to enter Realtek HD Audio Manager.

If you don’t plan to use WiFi+AP functin on this motherboard, this header can be

used as a 4-Pin USB 2.0 header to support one USB 2.0 port. To connect the

4-Pin USB device cable to this header, please refer to

this picture for proper installation.

CD1

La page est en cours de chargement...

ASROCK K10N78HSLI-GLAN Le manuel du propriétaire

ASROCK K10N78HSLI-GLAN Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents